Wacom DTU-1141 Instruction Manual

Contents

IndexContents

USER’S MANUAL Interactive Pen Display

Model: DTU-1141 and DTU-1031X Interactive Pen Display

Installation Using the pen Using and customizing the Radial Menu Customizing the ExpressKeys Application-specific settings Troubleshooting Technical support options

Contents

Index

Interactive pen display

Contents

Index

Wacom reserves the right to revise this publication without obligation to provide notification of such changes. Wacom does its best to provide current and accurate information in this manual. However, Wacom reserves the right to change any specifications and product configurations at its discretion, without prior notice and without obligation to include such changes in this manual.

The above year indicates when this manual was prepared. However, the date of release to the users of the manual is simultaneous with the introduction into the market of the applicable Wacom product.

Wacom is a registered trademark of Wacom Co., Ltd. Adobe and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United

States and/or other countries. Microsoft, Windows, and Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Apple, the Apple logo, and Macintosh are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.

Any additional company and product names mentioned in this documentation may be trademarked and/or registered as trademarks. Mention of third-party products is for informational purposes only and constitutes neither an endorsement nor a recommendation. Wacom assumes no responsibility with regard to the performance or use of these products.

Contents

Index

Interactive pen display

ABOUT THE MANUAL 4 Navigating the manual 5

YOUR INTERACTIVE PEN DISPLAY 6 Pen display features 6

Front view 7

Rear view 8 Pen display incline 9 Pen features 10

Pen Tether 10 INSTALLATION 11

System requirements 11 Step 1: Pen display installation 12 Step 2: Pen tablet installation 13

USB cable installation 13

Adding other display devices 14 WORKING WITH THE INTERACTIVE PEN DISPLAY 15

Ergonomics 15 Pen display orientation 15 Using the pen 16

Holding the pen 16

Positioning 16

Clicking 17

Dragging 17

Using the pen switch 18

Working with pressure sensitivity 18 Working with multiple monitors 18

Using the ExpressKeys 19 CUSTOMIZING 20

Opening the control panel 20 Control panel overview 21 Calibrating and adjusting the pen display 23 Customizing the pen 24

Adjusting tip feel and double-click 24

Advanced tip pressure settings 25

Customizing Pen mode and options 26 Customizing the ExpressKeys 27 Function settings 28 Using and customizing the Radial Menu 32 Working with Display Toggle 33

Index

CONTENTS

Application-specific settings 34

Creating an application-specific setting 35 Changing application-specific settings 36 Removing application-specific settings 36

TROUBLESHOOTING 37 Testing the interactive pen display 38 Testing your pen 39 Display troubleshooting 40

General display problems 40

Pen tablet troubleshooting 41

General problems 41 Windows-specific problems 44

Macintosh-specific problems 45 Technical support options 47 Obtaining driver downloads 48

APPENDIX 49 Caring for the interactive pen display 49 Replacing the pen tip 50 Using an alternate mount or stand 51 Uninstalling the interactive pen display 52 Managing preferences 53 Installing multiple tablets 54 Pen and digital ink capabilities in Windows 55 About the Windows Tablet PC Input Panel 56 Product information 57

Warranty Service 57 GLOSSARY 58 INDEX 60

Contents

Index

Interactive pen display

Contents

Index

ABOUT THE MANUAL

This document provides quick access to information about your interactive pen display. Click on a navigation button or highlighted word to move through the document. The information is common to Windows and Macintosh computers. Windows screen captures are shown, unless otherwise noted.

If you are new to electronic documentation, read navigating the manual

• Go directly to Contents

•S

MALL CAPITAL LETTERS identify the names of keyboard keys, dialog boxes, and Control Panel options.

• You can use your viewer zoom-in tool to increase the size of the page on your display screen.

• The following information is not included with this product: information about your specific computer hardware or operating system, or information about your application software. Your best source for this information is the set of manuals and discs that came with your hardware, operating system, or application.

• Many applications have built-in support for pen display features (such as pressure sensitivity). Visit Wacom’s web site to find a listing of applications that support these features (see product

information).

• For information on how best to use pen display features within a specific application, see the instructions in that application’s manuals.

or Index topics by clicking on them.

Wacom’s philosophy is to continually improve all of its products. As a result, engineering changes and improvements are made from time to time. Therefore, some changes, modifications, and improvements may not be covered in this document.

Contents

Index

Interactive pen display

Contents

Index

Contents

Index

NAVIGATING THE MANUAL

Use the navigation controls to move through the manual:

Go to front page.

Go to table of contents.

Go to index.

Go back to previous view.

Page back, or page forward.

Adobe for more information.

Reader® provides additional tools for using and printing the manual. See the Adobe Reader help

Contents

Index

Interactive pen display

Contents

Index

YOUR INTERACTIVE PEN DISPLAY

This manual describes the installation and use of interactive pen display DTU-1141 or DTU-1031X. The Wacom Control Panel enables you to customize your pen and pen display settings. To learn more, see

customizing Pen display features

Pen display incline Pen features

The following information is not included with this product: information about your specific computer hardware or operating system, or information about your application software. Your best source for this information is the set of manuals and discs that came with your hardware, operating system, or application.

Note: Not all product models are available in all regions. For illustrations of the items included with your pen display, see the Quick Start Guide included in the

product box.

PEN DISPLAY FEATURES

Familiarize yourself with the features and components of your product.

Contents

Index

Interactive pen display

Pen Display Features 1 - Status LED

2 - Pen storage compartment 3 - Pen stand 4 - ExpressKeys

DTU-

1141 ExpressKeys are shown as 1

through 4, from left to right (standard Landscape mode)

The features of the DTU-1141 pen display are illustrated below and listed in the Pen Display Features box. See Using the ExpressKeys

for descriptions and a table of default ExpressKey functions. Note: The DTU-1031X does not have ExpressKeys. Place the pen into the storage compartment by inserting the nib end of the pen into the left side of the

compartment with the side switch up. Gently press the pen into the compartment. Take care not to damage the pen nib.

Note: The DTU-1141 pen has a side switch, and the DTU-1031X pen does not. The DTU-1141 pen can be used with the DTU-1031X. To obtain a DTU-1141 pen, please contact your Wacom representative.

To place the cover on the pen compartment, position the cover with the pen nib outline facing to the left. Align the cover with the top of the pen compartment and press the cover into place.

Remove the pen by pressing on the pen tip side near the top notch to eject the opposite end from the compartment, being careful not to damage the pen nib. Grasp the pen and remove.

The pen can also be placed upright in the pen stand, or secured to the pen display with the pen tether provided (see Pen Tether

Pen Display Orientation Options

• Landscape (shown) - ExpressKeys top

• Landscape Flip - ExpressKeys bottom

• Portrait - ExpressKeys right

• Portrait Flip - ExpressKeys left

Contents

Index

FRONT VIEW

Contents

Index

Interactive pen display

The features of your DTU-1141 are illustrated below and listed in the Pen Display Features box. You can connect a security cable to the Security slot to prevent theft. The pen can be secured to the pen display through the pen tether holes with the pen tether provided (see

Pen Tether

The USB port is used to connect the pen display to your computer. See Step 2: Pen tablet installation

The leg stand can be used to incline the pen display. See Pen display incline

The pen display can be mounted to articulated arms or other third-party stands meeting the VESA specification for display stands. For details, see Using an alternate mount or stand

DTU-1141 Pen Display Features 5 - Security lock slot

6 - Pen tether holes 7 - USB port 8 - Rubber foot 9 - Leg stand 10 - VESA mount holes Note: Both the DTU-1141 and the DTU-

1031X have a single leg stand

Contents

Index

REAR VIEW

Contents

Index

Interactive pen display

You may want to place the pen display flat on your desk while you work. However, the leg stand on the back allows you to adjust your pen display to a different angle for working and viewing. Both the DTU-1031X and the DTU-1141 have a single leg stand. The diagram shows the leg stand for the DTU-1141.

Contents

PEN DISPLAY INCLINE

Index

Contents

Index

Interactive pen display

Pen switch): Be sure the pen’s programmable switch is in a convenient location where you can toggle it with your thumb or forefinger but not accidentally press it while using the pen. You can use the switch whenever the pen tip is within proximity of the display screen surface; you do not need to touch the pen tip to the display surface.

Note: The DTU-1141

pen has a side switch, and the DTU-

1031X pen does not. The DTU-1141 pen can be used with the DTU-1031X. To obtain a DTU-1141 pen, please contact your Wacom representative.

Pen tip (replaceable nib)

: The pen is activated as soon as it is brought within proximity (5 mm/.2 inch) of the pen display screen. This allows you to position the screen cursor without touching the pen tip to the display screen.

When pressure is applied to the pen tip, the pen simulates a primary mouse button click. Tip click pressure can be adjusted in the Wacom Control Panel.

PEN FEATURES

Contents

Index

Notes:

When not in use, place the pen in the pen storage compartment or the pen stand, or lay it flat on your desk. To maintain the sensitivity of your pen, do not store it in a position where it will rest on its tip.

Place the pen into the storage compartment by inserting the nib end of the pen into the left side of the compartment with the side switch up. Gently press the pen into the compartment. Take care not to damage the pen nib.

Important: Use only a pen specified for use with your pen display. Other pens may not function properly.

Also, the pen tip is specifically designed for use with the pen display. If your pen display has a coated surface, the tips on other pens could damage the pen display screen.

PEN TETHER

A pen tether to secure the pen to the pen display is provided. The pen is secured by threading the tether through the hole at the end of the pen and one of the tether holes at the top of the pen display. The attachment holes for the tether are shown in the Rear view.

Contents

Index

Interactive pen display

Contents

Index

INSTALLATION

The computer treats the interactive pen display as two separate devices (the display and the pen tablet). Therefore, the installation process is completed in two stages:

• First install as a display.

• Then install as a pen tablet. Both stages require hardware and software installations and adjustments. Carefully follow ALL instructions.

Important: You MUST install the Wacom driver software for correct pen-on-screen functionality.

System requirements Step 1: Pen display installation Step 2: Pen tablet installation

SYSTEM REQUIREMENTS

Make sure your computer meets the following minimum system requirements. DTU-1141:

• PC. Windows 8, Windows 7, Windows Vista ROM drive.

• Macintosh. OS X, v10.8 or greater. Available USB port, and CD-ROM drive.

DTU-1031X:

• PC. Windows 8, Windows 7, or Windows XP (32-bit and 64-bit). Available USB port and CD-ROM drive.

• Macintosh. OS X, v10.7 or greater. Available USB port, and CD-ROM drive.

Note: Wacom recommends that you use both USB connectors to ensure adequate power for the pen

display. However, your system may operate satisfactorily with just one USB connector attached to your computer.

™, or Windows XP (32-bit). Available USB port and CD-

Contents

Index

Interactive pen display

Contents

Index

STEP 1: PEN DISPLAY INSTALLATION

In this step, the driver for the interactive pen display is installed as a monitor on your system. Another application will also be installed to allow the pen display to work properly. The additional application is:

• For the DTU-1141: DisplayLink

• For the DTU-1031X: Magic Control Technology (MCT)

Important:

• You MUST install the Wacom driver and the DisplayLink (DTU-1141) or MCT (DTU-1031X) driver for

correct pen-on-screen functionality.

• You cannot use a DTU-1141 and DTU-1031X connected to the same computer at the same time.

DisplayLink and MCT cannot be installed on the same computer at the same time.

1. Save your work and close all open applications. Temporarily disable any virus protection programs.

2. Insert the Installation CD into your computer’s CD-ROM drive. If the software installer menu does not automatically display, double-click the I install the latest Wacom driver from the Wacom website for your region.

3. Click I

NSTALL TABLET and follow the prompts to install the drivers for the pen display.

• The DisplayLink driver will be installed automatically on Windows 8 and Windows 7. For Windows

XP and all Mac operating systems, it must be installed from the CD.

• The MCT driver must be installed from the CD for all operating systems.

• You can also download and install the DisplayLink driver at www.DisplayLink.com

driver at www.wacom.com.

• See Notes 3 and 4 below for information on re-installing and uninstalling drivers.

4. Reactivate your virus protection program.

5. If you have trouble installing the pen display, see troubleshooting

Notes:

1. Driver installation automatically activates the new pen input functions available within Microsoft

Windows 8, Windows 7, Vista, and XP (except for Windows Starter and Home Basic, and Windows Vista Home Basic). User-specific preferences are supported. After logging in, each user can customize their personal settings in the Wacom Control Panel. Switching to another user will automatically load the settings for that user.

2. On the Mac, you must restart your computer after installing the Wacom driver.

3. If you installing the Wacom and MCT drivers for a DTU-1031X, you must first uninstall any Wacom

or DisplayLink drivers already on the system. To uninstall the driver for the tablet, DisplayLink or MCT, see uninstalling the interactive pen display

4. If you do not use the provided CD for Wacom tablet driver installation, for example if you download

the Wacom driver from the Wacom website, DisplayLink or MCT will not install. You will need to download the DisplayLink driver, or the MCT driver, and install it separately. You can also reinstall either driver by using the Wacom Installation CD. However, on the DTU-1031X, you will need to uninstall any Wacom tablet or DisplayLink drivers before reinstalling.

5. DisplayLink does not support 64-bit Windows XP. MCT does not support Vista.

6. If the pen display does not respond properly or you lose cursor control, the pen display preferences

may be corrupted. You can delete the current preference settings and return the pen display to its factory default condition. See managing preferences

NSTALL icon located on the CD. You can also download and

, and the MCT

Contents

Index

Interactive pen display

Contents

Index

STEP 2: PEN TABLET INSTALLATION

In this step, the interactive pen display is installed as a pen tablet.

USB CABLE INSTALLATION

1. Place your pen display face-down near your computer, using a soft cloth underneath the pen display to protect the surface.

2. Plug the square end of the USB cable into the USB port of the pen display.

3. Place the USB cable attachment on the USB cable as shown, to prevent it from becoming unplugged. If you need to remove the attachment, press in on both sides of the attachment and lift up.

4. Turn the pen display face up.

5. Plug the two connectors at the other end of the USB cable into two available USB ports on your computer.

Note: Wacom recommends that you use both of these USB connectors to ensure adequate power for

the pen display. However, your system may operate satisfactorily with just one USB connector attached to your computer.

6. Turn on your computer.

7. Check the status light (LED) on your pen display. When there is a connection between the computer and the pen display, the status light is dimly lit. When the computer and pen display are connected and the pen is in proximity of the display surface, the status light changes to a steady blue.

8. After completing the software installation (Step 1), make sure you can use your pen on the interactive pen display to move the screen cursor.

9. When you place the pen tip on the display screen, the screen cursor should immediately jump to a corresponding position approximately beneath the pen tip. Lift the pen tip and place it on the display screen surface in a different location. The screen cursor should again jump to the new position. This is known as absolute positioning, and enables you to position the screen cursor without having to drag your pen across the display screen surface.

10. See calibrating and adjusting the pen display

11. To change the brightness of the pen display, adjust the Brightness setting in the Wacom Control Panel (see Customizing

Note: Windows

pen display in your display properties Control Panel.

: If you are using the pen display as a secondary display, you may first need to enable the

to precisely align the screen cursor to the pen tip.

Contents

Index

Interactive pen display

Contents

Index

ADDING OTHER DISPLAY DEVICES

You can connect another display device to your computer’s VGA or DVI connector for use with the pen display. When working with more than one monitor, the pen display will map to the monitors based on how your system is configured. By default, if you are in mirror mode, the pen display will map to the entire space on each monitor.

Note: Make sure you complete the pen display installation before connecting another device to the unit. The Display Toggle

toggle the screen cursor between the pen display and other monitors. Refer to your hardware and operating system documentation for information on connecting other monitors

to your computer and configuring your system for use with multiple monitors. Be sure to use the correct cable and connector when adding an additional device to your system.

For troubleshooting tips, see troubleshooting Notes for the pen display screen:

Each interactive pen display LCD panel is produced under very stringent quality standards. Production techniques cannot guarantee an absolutely perfect display, and some panels may exhibit a certain number of pixels that show an incorrect color.

If an image has fine striping (such as screen stripes), it may appear to flicker or display a moiré pattern.

Do not apply excessive pressure on the display screen surface; it may cause the appearance of a moiré or pooling pattern. If this occurs, use less pressure on the display screen when working with the pen.

When a still image is displayed for a long period of time, an after-image may remain for a short time. To prevent this, use a screen saver or other power management feature.

To extend the life of the pen display backlight, set your computer’s power management to turn off the display when it is not in use for extended periods of time.

function is available for use on systems with more than one monitor. This enables you to

Contents

Index

Interactive pen display

Contents

Index

WORKING WITH THE INTERACTIVE PEN DISPLAY

As you work with the pen display you can rest your hand lightly on the display screen, just as if it were a sheet of paper.

Because the pen display surface will be a little higher than your desk, consider adjusting the height of your desk or chair to assure comfortable use of the device.

Ergonomics Using the pen Working with multiple monitors Customizing Pen mode and options

ERGONOMICS

To minimize fatigue, comfortably organize your work area. Position your pen display, the pen, and your keyboard for easy access without unnecessary reaching. The pen display and any other displays should be positioned so you can view them comfortably with a minimum of eyestrain.

• Take short breaks between tasks to stretch and relax your muscles.

• Use a gentle grip when working with the pen.

• Alternate tasks throughout the day.

• Maintain a good posture at all times. Minimize awkward postures and repetitive movements that cause discomfort.

• Change your position if you feel any discomfort due to your work position.

Tip

The pen display can also be mounted to articulated arms or other third-party stands meeting the VESA specification for display stands. For details, see using an alternate mount or stand

PEN DISPLAY ORIENTATION

Your pen display can be rotated for use in one of two landscape orientations, or one of two portrait orientations. These positions are listed in the Pen Display Orientation Options list (see Pen Display

Orientation Options). Refer to your hardware and operating system documentation for information on

setting the pen display to your preferred orientation.

Contents

Index

Interactive pen display

To position the screen cursor, move the pen slightly above the pen display screen without touching the screen surface. Press the pen tip on the display screen to make a selection.

Note: Calibrating and adjusting the pen display

ensures correct alignment of the screen cursor with the pen tip. If the screen cursor does not jump to a position near the pen tip when you place the pen on the display screen, the pen display software driver may not be installed or is not loading. Re-install the driver software if necessary. Also see troubleshooting

Contents

Index

USING THE PEN

The pen is cordless, battery-free, and senses the amount of pressure you apply to the tip.

Holding the pen Positioning Clicking Dragging Using the pen switch Working with pressure sensitivity Working with multiple monitors

HOLDING THE PEN

Hold the pen like you would a normal pen or pencil. As you work with the interactive pen display you can rest your hand lightly on the display screen. You can tilt the pen in any way that feels most comfortable.

For information on changing the pen settings, see customizing

POSITIONING

Contents

Index

Interactive pen display

Tap the display screen once with the pen tip, or touch the pen to the display screen with enough pressure to register a click.

Windows tip

: To make navigating with the pen easier, configure Windows to select when the pen is over an icon and to launch the icon with a single click. To turn on this feature, first open a folder.

For Windows 8, Windows 7 and Vista

: From the ORGANIZE

pull-down menu choose F

OLDER AND SEARCH OPTIONS.

From the G

ENERAL tab select SINGLE-CLICK TO OPEN AN ITEM

(

POINT TO SELECT). Note: Vista is not supported on the DTU-

1031X. For Windows XP

: From the TOOLS pull-down menu choose

OLDER OPTIONS.... From the GENERAL tab select SINGLE-

CLICK TO OPEN AN ITEM (POINT TO SELECT).

Press the switch if it is set to D

OUBLE CLICK, or quickly tap

the display screen twice in the same place with the pen tip. Double-clicking is easier when the pen is perpendicular to the pen display screen.

Select an object, then slide the pen tip across the display screen to move the object.

CLICKING

Contents

Index

DRAGGING

Contents

Index

Interactive pen display

Contents

Index

USING THE PEN SWITCH

The pen has a programmable switch that can be used whenever the pen tip is within proximity (5 mm (0.2 inch)) of the display screen surface. You do not need to touch the pen tip to the display surface in order to use the switch. By default, the switch is set to R disabled using the Wacom Control Panel. See customizing

Note: The DTU-1141 pen has a side switch, and the DTU-1031X pen does not. The DTU-1141 pen can be used with the DTU-1031X. To obtain a DTU-1141 pen, please contact your Wacom representative.

IGHT CLICK. The switch function can be modified or

WORKING WITH PRESSURE SENSITIVITY

The pen responds to the nuance and inflection of your hand movements, enabling you to create naturallooking pen strokes within applications that support this feature. To annotate and write with pressure, select a pressure-sensitive tool from your application’s tool palette. As you work on the screen surface, use various amounts of downward pressure on the tip of the pen.

WORKING WITH MULTIPLE MONITORS

When you are working with the pen display and additional monitors on the same system, the screen cursor movement on the standard monitors will depend on your system configuration.

If a second monitor is connected in mirror mode, both the pen display and the other monitor will show identical images and screen cursor movement.

If you are using the pen display with other monitors in extended monitor mode, you have the following options for navigating on the other monitors:

• Set the pen switch to the D cursor between the pen display and your other displays. For example, your product can be used as a pen display (the screen cursor is positioned at the pen tip location) or toggled for use as a standard Wacom tablet (the screen cursor can be moved across the entire desktop or additional displays). See

Working with Display Toggle

• Set the pen switch to M pen display and mouse mode for working on the other monitors.

• Set an ExpressKey to D

ISPLAY TOGGLE function. You can then press the switch to toggle the screen

for more information.

ODE TOGGLE. You can then quickly switch between pen mode for working on the

ISPLAY TOGGLE or MODE TOGGLE function.

Contents

Index

Interactive pen display

Contents

Index

USING THE EXPRESSKEYS

Press individual keys to perform frequently used functions or keystrokes. ExpressKeys can also be used to modify your pen properties as you work. Please note that there are no ExpressKeys on the DTU-1031X.

Default settings are shown by ExpressKey numbers, which are numbered 1 through 4 from left to right and shown in Front view

Customizing

ExpressKeys can also be operated in combination with one another. When you press both keys at the same time, a combination function is initiated.

. Use the Wacom Control Panel to set other functions for the ExpressKeys (see

ExpressKey Number Function

1 Scroll Up 2

3 Z 4

Scroll Down

OOM IN

ZOOM OUT

Contents

Index

+ 42 hidden pages