Ultimate Speed Car Seat Cover User Manual [en, fr, de]

CAR SEAT COVER SET

GB IE

CAR SEAT COVER SET

Assembly and safety advice

SE

BILKLÄDSEL-SET

Monterings- och säkerhetsanvisningar

FR BE

HOUSSES DE SIEGES AUTO

Instructions de montage et consignes de sécurité

DE

ATIECH

AUTOSITZBEZUG-SET

Montage- und Sicherheitshinweise

IAN 89890

FI

AUTON ISTUINPÄÄLLINEN

Asennus- ja turvaohjeet

DK

BILSÆDEBETRÆK-SÆT

Monterings- og sikkerhedshenvisninger

NL BE

SET AUTOSTOELBEKLEDINGEN

Montage- en veiligheidsinstructies

GB

SE DK BE

FI

GB IE

Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the
product.

FI

Käännä ennen lukemista molemmat kuvalliset sivut esiin ja tutustu seuraavaksi tarkemmin tuotteen kaikkiin
osiin.

SE

Vik ut båda bildsidorna och ha den till hands när du läser igenom anvisningarna. Gör dig sedan bekant
med produktens funktioner.

DK

Klap begge sider med illustrationerne ud, inden du læser, og sæt dig ind i alle produktets funktioner.

FRNLBE

Avant de lire le mode d‘emploi, ouvrez les deux pages contenant les illustrations et familiarisez-vous
ensuite avec toutes les fonctions du produit.

BE

Vouw vóór het lezen de beide pagina‘s met de afbeeldingen open en maak u vertrouwd met alle functies
van het product.

DE

AT CH

Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend
mit allen Funktionen des Produkts vertraut.

GB/IE Assembly and safety advice Page 5
FI Asennus- ja turvaohjeet Sivu 7
SE Monterings- och säkerhetsanvisningar Sidan 9
DK Monterings- og sikkerhedshenvisninger Side 11
FR/BE Instructions de montage et consignes de sécurité Page 13
NL/BE Montage- en veiligheidsinstructies Pagina 15
DE/AT/CH Montage- und Sicherheitshinweise Seite 17

1

5 6 7 8

9 10 11 12

2 3 4

13 14 15 16

17 18 19 20

21 23 24

22

25 26 27

28 29 30

31 32 33 34

35 36 37

38 39 40

42

43 44 45

41

Car seat cover set

DANGER OF SUFFOCATION! Keep

WARNING!

the packaging out of reach of small children.

Introduction

We congratulate you on your purchase. You have chosen a high
quality product. The instructions for use are to be considered as

part of this product. Before using the product, please familiarise
yourself with all the safety information and instructions for use. Only use the
product as instructed and only for the stated areas of use. If you pass the product
on to anyone else, please ensure that you also pass on all the documentation
with it.

Intended use

Set of car seat covers for the driver‘s seat, passenger‘s seat and the back
seats of cars (according to the enclosed type list).

Scope of delivery

Installation is permissible only in cars that are indicated in the list of types

on the packaging or in the enclosed, detailed list of types.

Correct assignment of the seat (driver and front passenger seat). The
covers are assigned by the marking „airbag“ attached to the seat cover.
This marking must be attached to the outer side of the backrest
(see fig. 1.0).

Fig. 1.0

Headrest inserts, adjustment levers / wheels for release of backrests or
armrests may not be covered with the seat cover. Allowances must be
made for appropriate inserts. Please observe the instructions given in
section “Installation”.

Displaced seat covers must be repositioned. If this is no longer possible
due to a advanced state of wear and tear, the cover must be removed or
replaced.

Manipulation of the opening of the seat covers is not permissible
(no covering, sewing up or repairs by yourself).

2 x covers for front seats (in 1 or 2 - 5 x covers for headrests
2 parts according to design) (according to design)

1 x cover for rear backrest (in 1 1 x cover for back seat (not sepa
to 5 parts according to design) rable)

Metal hooks (located in the List of types
headrest covers)

Safety instructions

Correct installation res. fastening of the seat covers to the vehicle is essential
to guarantee the safety of the user. Please pay attention to the following
information when installing the seat covers:

This protective cover has been tested by TÜV Rhineland Group.

CAUTION! If the seat covers are installed incorrectly, the proper extension

and inflation of the seat air bag cannot be guaranteed in the case of a
collision.

Installation

You need a pair of pointed scissors.

Installation of seat covers

Important: Please read the information below before installing the seat covers!

Fig. 1: Remove headrests (in some car models the headrests must

be dismantled in a garage).

Fig. 2: Cover the backrest by pulling the cover downwards.
Fig. 3: Pay attention to the correct assignment of the side airbag

label (right / left seat)! The side airbag label must be located
at the outside (door side) of the respective seat.

Fig. 4: Pull the strap through between the seat and the backrest.
Fig. 5: Then close the fastener.
Fig. 6: Cover the seat from the front to the back.
Fig. 7: Fasten the metal hooks to the rubber loops.
Fig. 8+9: Pull the rear rubber loops between the seat and backrest

(as you did with the strap of the backrest cover). Fasten the
metal hooks under the seat according to the car model
(e.g. to the existing metal rods - ATTENTION Do not fasten
to airbag cables!)

Fig. 10: Or fasten all rubber loops together.

ATTENTION!

Openings for backrest releases, adjustment levers, side levers etc. (as described
under fig. 11–21) must be cut out.

GB/IE 5

If your seat is equipped with armrests, proceed as described
under fig. 11. Otherwise go to fig. 15.

Fig. 11: Pull the cover down as far as the armrest. The cover must be

tightly fitting on top.
Fig 12: Cut the cover in the position of the armrest. The cut-out may
not be too large.
Fig. 13: Push up the armrest and pull it through the cut-out opening
of the cover.
Fig. 14: Pull the strap through between the seat and the backrest and
close with the fastener.

If your seat is equipped with side levers, proceed as described
under fig. 15. Otherwise go to fig. 19.

Fig. 15: Cover the seat as described under section 2. The cover must

be tightly fitting on top.
Fig. 16: Cut the cover in the position of the side lever. The cut-out may
not be too large.

Fig. 17+18: With the aid of scissors, push the cover under the guide fitting.

Instructions for care and disposal

Wash the covers by hand

Do not use bleach

Do not dry in a tumbler

Do not iron

Do not dry clean

The seat covers can be disposed of in the household waste.

Please dispose of the packaging in accordance with the local regulations.

If your seat is equipped with seat frame cladding, proceed as
described under fig. 19. Otherwise go to fig. 22.

Fig. 19: (for Renault) Open the seat frame cladding under the seat.
Fig. 20: (for Mercedes) Open the seat frame cladding under the seat.
Fig. 21: Fold the seat frame cladding under the seat cover. Pull the

strap through between the seat and the backrest. Then close
the fastener at the back.

Fig. 22: Cover the headrests.
Fig. 23+24: Position the mounting strip directly above the holes for insertion

of the headrest. Cut open the mounting strip in the exact
positions of the headrest holes. With the aid of the integrated
mounting strip, it is not possible for the material to tear.
Fig. 25+26: Push the cover beneath the plastic of the headrest guide
covering. In a few isolated car models, it could be the case
that these models have no headrest guide covering.
Fig. 27+28: Pull the cover for the back seat towards the back of the seat.
If necessary, tilt the back seat forward and fasten the rubber
loops at the back to the metal hooks (according to the car
model).

Fig. 29: Position the cover exactly in the location of the seat belt.
Fig. 30: Carefully cut the cover in the position of the seat belt.
Fig. 31: Push the cover under the seat belt holder.
Fig. 32: Pull the cover under the backrest. The cover must be under

the seat belt!

Fig. 33: Cut the cover in the position of the belt guide.
Fig. 34+35: Push the cover beneath the plastic of the belt guide.
Fig. 36: The backrest cover is universally suitable for all back seats

due to the triple zip fastener division. The zip-in part can be
used according to the width of the rear backrest.

Fig. 37: Fasten the rubber loops at the back to the metal hooks.

Service

Please contact our Service Hotline in the first instance, before you return the
seat covers to the manufacturer.

Service address:

Walser Industrie- und Handels GmbH
Langenweg 34
DE-88131 Lindau
Germany

Return address:

Walser Customer Service Germany
Walser GmbH
Bleicheweg 15, Postfach 3325
D-88131 Lindau
Germany

Telephone number of Service-Hotline: [phone]
www.walsergroup.com / clix

IAN 89890

If your back seat is equipped with armrests, proceed as
described under fig. 38. Otherwise go to fig. 40.

Fig. 38: Open the zip fasteners. Fold out the armrest. Close the zip

fastener up to the armrest.

Fig. 39: Complete covered armrest.
Fig. 40: In case of divided back seats, open the variable zip fasteners

with the slider facing upwards if necessary.

Fig. 41: Remove the rear headrests.
Fig. 42: Cover the rear headrests.
Fig. 43: Cut the backrest cover in the position of the headrest in an

x-shaped form.
Fig. 44+45: Push the cover under the plastic.

6 GB/IE