Ubiquiti ULEDAC User Manual
LED
Network-Managed
LED Panel Powered by AC
Model: ULED-AC
Introduction
Thank you for purchasing the Ubiquiti Networks® UniFi®LED
Panel. This Quick Start Guide is designed to guide you through
installation and includes warranty terms.
Package Contents
LED
Network-Managed
LED Panel Powered by AC
Model: ULED-AC
UniFi LED Panel Quick Start Guide
System Requirements
• Network switch (for wired configuration), or access point (for
wireless configuration)
• UniFi LED mobile app software
• Mobile device: iOS 10 or Android 5.0
• UniFi EoT Controller software
• Computer: UniFi Application Server 0.5.0, Ubuntu 16.04
LTS (Xenial Xerus) 64-bit or Debian 9 64-bit
• Web browser: Google Chrome (Other browsers may have
limited functionality.)
• UniFi Dimmer Switch, model UDIM-AC or UDIM-AT
TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet
cable and earth grounding must be used as conditions of product warranty. TOUGHCable™ is
designed for outdoor installations. It is the professional installer’s responsibility to follow local
country regulations, including operation within legal frequency channels, output power, and
Dynamic Frequency Selection (DFS) requirements.
Installation Requirements
• Phillips screwdriver
• Wire stripper/cutter
• Needle-nose pliers (Optional)
IMPORTANT: The ULED-AC is to be installed by
a qualified electrician in accordance with local
electrical codes and regulations.
IMPORTANT : Le ULED-AC doit être installé par
un électricien qualifié conformément aux codes
électriques locaux et des règlements.
WARNING: TO AVOID FIRE, SHOCK OR DEATH, turn off
power at the circuit breaker or fuse before installing.
AVERTISSEMENT : POUR ÉVITER TOUT RISQUE
D'INCENDIE, D'ÉLECTROCUTION OU DE DÉCÈS;
coupez le courant au niveau du disjoncteur ou du
coupe-circuit ou fusible avant l'installation.
Network Topology Requirements
Network topology requirements are as follows:
• DHCP-enabled network (for the UniFi LED Panel to obtain
an IP address)
• Network switch (for wired configuration), or access point (for
wireless configuration)
• For UniFi Dimmer Switch only:
A UniFi Dimmer Switch connected to the same Layer 2
network as the UniFi LED Panel
• For EoT Controller software:
A UniFi Application Server running the UniFi EoT Controller
software and connected to the same Layer 2 network as a
the UniFi LED Panel
• For UniFi LED app only:
A UniFi AP connected to the same Layer 2 network as the
UniFi LED Panel
Connection Options
A UniFi LED Panel can use either a wired connection or a
wireless connection. A wired connection to a switch allows
immediate detection and control by the EoT Controller, but
if a panel is in a location where Ethernet cabling is not a
reasonable option, then the panel can connect via Wi-Fi to a
UniFi AP.
Control Options
You can control the UniFi LED Panel’s state (on/off) and
brightness. There are three ways to control the Panel:
UniFi Dimmer Switch A user in the immediate vicinity
controls the UniFi LED Panel using the UniFi Dimmer Switch.
UniFi LED App over Layer 2 Network A local user runs the
app to connect to a UniFi AP on the same Layer 2 network as
the UniFi LED Panel.
UniFi EoT Controller over Layer 2 Network Alocal user runs
the EoT Controller software on the same Layer 2 network as
the UniFi LED Panel.
UAP-AC-PRO
UniFi LED
100-277VAC
ULED-AC
802.3af PoE
App
UniFi PoE Switch
USG-XG-8
(DHCP Server)
Sample Network Diagram - Wireless Topology
UDIM-AT
LAN
WAN
OR
UniFi EoT
Controller
Internet
UDIM-AC
100-240VAC
UniFi Application Server
UniFi Application Server
ULED-AC
UAP-AC-PRO
UniFi LED
App
UniFi PoE Switch
Ethernet
802.3af PoE
LAN
UDIM-AT
UniFi EoT
Controller
100-277VAC
USG-XG-8
(DHCP Server)
WAN
Sample Network Diagram - Wired Topology
*640-00340-03*
640-00340-03
Internet
Daisy-Chain Configuration
For installations using multiple UniFi LED Panels in a wired
configuration, we recommend using a daisy chain topology,
asillustrated in the following diagram.
(Additional LED Panels)
UniFi EoT
Controller
Internet
100-277VAC
100-277VAC
Ethernet
ULED-AC
Ethernet
ULED-AC
802.3af PoE
UDIM-AT
UniFi PoE Switch
LAN
USG-XG-8
(DHCP Server)
Daisy Chain Topology - Sample Network Diagram
WAN
UniFi Application Server
Hardware Overview
LED
Status LED
State Status
Flashing White Initializing.
Steady White System ready.
Steady Blue Adopted by EoT Controller.
Alternating
White/Blue
Ports
Ethernet Use these 10/100 Ethernet ports to connect to the
LAN or to daisy-chain with other UniFi LED Panels.
Firmware upgrade is taking place.
Ethernet
Loading...