TP-Link TL-WPA7510 KIT Quick Installation Guide
Ethernet Cable
Powerline
Internet
1000Mbps
Quick Installation Guide
1000Mbps
SSID:TP-LINK_XXXX
SSID:TP-LINK_XXXX_5G
Wireless Password:XXXXXXXX
1000Mbps
SSID:TP-LINK_XXXX
SSID:TP-LINK_XXXX_5G
Wireless Password:XXXXXXXX
WAN LAN
TL-WPA7510 KIT
* TL-WPA7510 KIT (European version) is used for demonstration in this guide.
Plug and Play
Extender
TL-WPA7510
On
2
Plug the extender into a power outlet on the same electrical circuit.
Wait until the extender’s Powerline LED turns on.
Note: If the LED is blinking or o, please refer to FAQ > Q2.
3
Connect your devices to the internet using the default SSID (network
name) and password on the label at the top of the extender.
SSID:TP-Link_XXXX
SSID:TP-Link_XXXX_5G
Wireless Password:XXXXXXXX
Router
Adapter
TL-PA7010
1
Plug the adapter into a power outlet
and connect it to the router’s LAN
port via an Ethernet cable.
Tip:
Want to unify Wi-Fi networks or personalize your network?
See the back page for instructions.
Attention
1. Use the product only in the upright direction.
2. Plug powerline devices into wall outlets instead of power strips.
Using power strip will aect network performance or even cause connection drops.
Wall Outlet
Power Strip
©2018 TP-Link 7106508210 REV2.1.0
1000Mbps
PairLED
Wi-Fi
Reset
Unify Your Wi-Fi Networks via WPS
Pair
1000Mbps
1000Mbps
PairLED
Wi-Fi
Reset
SSID:TP-LINK_XXXX
SSID:TP-LINK_XXXX_5G
Wireless Password:XXXXXXXX
1000Mbps
Pair
LED
Wi-Fi
Reset
WPS
SSID:TP-LINK_XXXX
SSID:TP-LINK_XXXX_5G
Wireless Password:XXXXXXXX
Personalize Your Network
Copy SSID and password from your router via WPS to create one unied Wi-Fi network throughout your home.
Note: If your router doesn’t have a WPS button, manually change the extender’s Wi-Fi settings via the tpPLC app, tpPLC Utility, or web interface.
Plug in the extender in the same room as your router. Wait
1
until the extender’s Wi-Fi LEDs turn on.
Press your router’s WPS button. Within 2 minutes, press the
2
extender’s Wi-Fi button for 1 second. The extender’s Wi-Fi
LEDs start blinking. When they stay on, Wi-Fi settings
are copied.
Note: If Wi-Fi settings are not copied within 2 minutes, manually change the
extender’s Wi-Fi settings.
Relocate the extender and enjoy the internet using your
3
Within 2 minutes
WPS/
Wireless Router Extender
Blinking
router’s SSID and password.
Create a Secure Powerline Network by Pairing
Note: You can only pair two devices at a time. We recommend that you plug in the powerline devices near each other when pairing.
Pair the Powerline Devices
Press the Pair button on the adapter for 1 second. Its Power
1
LED starts blinking.
Note: If the Power LED does not blink, press the Pair button again.
Within 2 minutes, press the the extender’s Pair button for 1
2
second. Its Power LED starts blinking.
3
When the extender’s Powerline LED turns on, the pairing
process is complete.
Adapter
Blinking
Within 2 minutes
Extender
Manage your powerline devices using any of the methods below. You
can change the SSID and password, set Wi-Fi schedules, create a guest
network and more.
tpPLC App
On
For easy management via your smartphone or tablet, download the app
from the App Store or Google Play, or simply scan the QR code.
tpPLC AppScan to download
tpPLC Utility
For easy management via your computer, download the utility on the
Blinking
On
product’s Support page at https://www.tp-link.com.
Note: For detailed instructions, refer to the utility manual on the product’s Support page.
Web Interface
To access all settings, connect to an extender wirelessly and visit
http://tplinkplc.net. Use admin for both username and password
upon initial login.
Note: For detailed instructions, refer to the product manual on the product’s Support page.
Sync Wi-Fi Settings to More Extenders
If you have more extenders, simply plug in and pair each one with the existing adapter to join the network. Then the Wi-Fi settings will automatically
sync from the existing extender to the new ones.
Button Legend
Frequently Asked Questions
Extender TL-WPA7510
Reset
Press for at least 2 seconds until all LEDs turn o to reset the
extender to factory default settings.
Pair
Press for 1 second on two powerline devices within two minutes
to pair them.
LED
Press for 1 second to turn all LEDs on or o.
Wi-Fi
Press for 1 second to begin or stop copying Wi-Fi settings from
the router.
Press for about 5 seconds to turn Wi-Fi on or o.
Q1. How do I reset my extender to factory default settings?
A. With the extender plugged into an electrical outlet, press and hold the Reset button until all LEDs
turn o. When the LEDs turn back on, the reset process is complete.
Q2. What should I do if the Powerline LED is blinking or o?
If the LED is blinking:
A. The powerline device is in a location with a poor signal strength. Try another wall socket.
If the LED is o:
A1. Try another wall socket and make sure all powerline devices are on the same electrical circuit.
A2. Try to set up a powerline network by pairing. Refer to the section above for instructions.
A3. If the problem persists, contact our Technical Support.
Q3. What should I do if there is no internet connection in my powerline network?
A1. Make sure all powerline adapters and extenders are on the same electrical circuit.
A2. Make sure the Powerline LEDs are lit on all of your powerline devices. If they are not, pair all
devices again.
A3. Make sure all devices are correctly and securely connected.
A4. Check if you have an internet connection by connecting the computer directly to the modem or
router.
after it is relocated?
A1. Make sure all powerline adapters and extenders are on the same electrical circuit.
A2. Try to pair the extender again, and make sure the Powerline LED is on.
A3. Check for possible interference due to a washing machine, air conditioner or other
household appliance that may be too close to one of the powerline devices. Plug the
appliance into the integrated electrical socket to remove the electrical noise if your
powerline device has an integrated electrical socket.
For technical support, the user guide and more information, please visit
https://www.tp-link.com/support, or simply scan the QR code.
TP-Link hereby declares that the device is in compliance with the essential requirements and other
relevant provisions of directives 2014/53/EU, 2009/125/EC and 2011/65/EU. The original EU
declaration of conformity may be found athttp://www.tp-link.com/en/ce.
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device.
Do not use the device where wireless devices are not allowed.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
Plug the powerline devices directly into the wall outlets but not the power strips.
Q4. What should I do if a successfully-paired extender does not reconnect
Loading...