TP-Link TL-WPA7510 Installation Manual

Quick Installation Guide

TL-WPA7510 KIT

* TL-WPA7510 KIT (European version) is used for demonstration in this guide.

Plug and Play

Powerline

LAN

WAN

1000Mbps

Adapter

TL-PA7010

1000Mbps

Extender

TL-WPA7510

1 Plug the adapter into a power outlet and connect it to the router’s LAN port via an Ethernet cable.

Cable

Ethernet

Internet

2 Plug the extender into a power outlet on the same electrical circuit. Wait until the extender’s Powerline LED turns on.

Note: If the LED is blinking or off, please refer to FAQ > Q2.

Connect your devices to the internet using the default SSID (network name) and password on the label at the top of the extender.

SSID:TP-Link_XXXX

SSID:TP-Link_XXXX_5G

Wireless Password:XXXXXXXX

	Tip:
	Want to unify Wi-Fi networks or personalize your network?
1000Mbps	See the back page for instructions.

Attention

1.Use the product only in the upright direction.

2.Plug powerline devices into wall outlets instead of power strips.

Using power strip will affect network performance or even cause connection drops.

Wall Outlet

Power Strip

Unify Your Wi-Fi Networks via WPS

Copy SSID and password from your router via WPS to create one unified Wi-Fi network throughout your home.

Note: If your router doesn’t have a WPS button, manually change the extender’s Wi-Fi settings via the tpPLC app, tpPLC Utility, or web interface.

1Plug in the extender in the same room as your router. Wait until the extender’s Wi-Fi LEDs turn on.

2Press your router’s WPS button. Within 2 minutes, press the extender’s Wi-Fi button for 1 second. The extender’s Wi-Fi

LEDs start blinking. When they stay on, Wi-Fi settings

are copied.

Note: If Wi-Fi settings are not copied within 2 minutes, manually change the extender’s Wi-Fi settings.

3Relocate the extender and enjoy the internet using your router’s SSID and password.

WPS

	Within 2 minutes
	10
	00Mbps
Wireless Router	Extender

<![if ! IE]>

<![endif]>Wi-Fi LED Pair Reset

Blinking

Create a Secure Powerline Network by Pairing

Note: You can only pair two devices at a time. We recommend that you plug in the powerline devices near each other when pairing.

Pair the Powerline Devices

1Press the Pair button on the adapter for 1 second. Its Power

LED starts blinking.

Note: If the Power LED does not blink, press the Pair button again.

2Within 2 minutes, press the the extender’s Pair button for 1 second. Its Power LED starts blinking.

3When the extender’s Powerline LED turns on, the pairing process is complete.

<![if ! IE]>

<![endif]>Pair

1000Mbps

Adapter

Blinking

Within 2 minutes

1000Mbps

Extender

Blinking

<![if ! IE]>

<![endif]>Wi-Fi LED Pair Reset

Sync Wi-Fi Settings to More Extenders

If you have more extenders, simply plug in and pair each one with the existing adapter to join the network. Then the Wi-Fi settings will automatically sync from the existing extender to the new ones.

Personalize Your Network

Manage your powerline devices using any of the methods below. You can change the SSID and password, set Wi-Fi schedules, create a guest network and more.

tpPLC App

For easy management via your smartphone or tablet, download the app from the App Store or Google Play, or simply scan the QR code.

Scan to download

tpPLC App

tpPLC Utility

For easy management via your computer, download the utility on the product’s Support page at https://www.tp-link.com.

Note: For detailed instructions, refer to the utility manual on the product’s Support page.

Web Interface

To access all settings, connect to an extender wirelessly and visit http://tplinkplc.net. Use admin for both username and password upon initial login.

Note: For detailed instructions, refer to the product manual on the product’s Support page.

<![if ! IE]>

Button Legend

			Extender TL-WPA7510
			Reset
			Press for at least 2 seconds until all LEDs turn off to reset the
<![if ! IE]> <![endif]>Reset			extender to factory default settings.
<![if ! IE]> <![endif]>Pair			Pair
<![if ! IE]> <![endif]>Pair			Pair
<![if ! IE]> <![endif]>LED			Press for 1 second on two powerline devices within two minutes
<![if ! IE]> <![endif]>Wi-Fi			to pair them.
			LED
			LED
1000Mbps			Press for 1 second to turn all LEDs on or off.
1000Mbps			Wi-Fi
			Wi-Fi
			Press for 1 second to begin or stop copying Wi-Fi settings from
			the router.
			Press for about 5 seconds to turn Wi-Fi on or off.

Frequently Asked Questions

Q1. How do I reset my extender to factory default settings?

A.With the extender plugged into an electrical outlet, press and hold the Reset button until all LEDs turn off. When the LEDs turn back on, the reset process is complete.

Q2. What should I do if the Powerline LEDis blinking or off?

If the LED is blinking:

A. The powerline device is in a location with a poor signal strength. Try another wall socket.

If the LED is off:

A1. Try another wall socket and make sure all powerline devices are on the same electrical circuit. A2. Try to set up a powerline network by pairing. Refer to the section above for instructions.

A3. If the problem persists, contact our Technical Support.

Q3. What should I do if there is no internet connection in my powerline network?

A1. Make sure all powerline adapters and extenders are on the same electrical circuit.

A2. Make sure the Powerline LEDsare lit on all of your powerline devices. If they are not, pair all devices again.

A3. Make sure all devices are correctly and securely connected.

A4. Check if you have an internet connection by connecting the computer directly to the modem or router.

Q4. What should I do if a successfully-paired extender does not reconnect after it is relocated?

A1. Make sure all powerline adapters and extenders are on the same electrical circuit. A2. Try to pair the extender again, and make sure the Powerline LED is on.

A3. Check for possible interference due to a washing machine, air conditioner or other household appliance that may be too close to one of the powerline devices. Plug the appliance into the integrated electrical socket to remove the electrical noise if your powerline device has an integrated electrical socket.

For technical support, the user guide and more information, please visit https://www.tp-link.com/support, or simply scan the QR code.

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC and 2011/65/EU. The original EU declaration of conformity may be found at http://www.tp-link.com/en/ce.

Safety Information

Keep the device away from water, fire, humidity or hot environments.

Do not attempt to disassemble, repair, or modify the device.

Do not use the device where wireless devices are not allowed.

The socket-outlet shall be installed near the equipment and shall be easily accessible.

Plug the powerline devices directly into the wall outlets but not the power strips.