TP-Link OC200 Installation Guide
Thank you for purchasing OC200, the Omada Cloud Controller.
This Installation Guide is designed to guide you through
installation.
Package Contents
Typical Network Topology
A DHCP server (typically a router) with DHCP function enabled
is required to assign IP addresses to the EAPs and OC200 in
your local network.
OC200
Installation Guide
Omada Cloud Controller
7106508054 REV1.0.0
Hardware Overview
Front Panel
Cloud LED
Power LED
ETH1 (PoE IN) ETH2 USB 2.0 Port Reset
Cloud LED
On: The device is bound to a TP-Link ID.
Slow Flashing: The device is connected to cloud but not
bound to a TP-Link ID.
Quick Flashing: The device is being reset to its factory default
settings.
O: The device is disconnected from cloud.
OC200
Installation Guide
Omada Cloud Controller
OC200
Ethernet Cable
ETH2 Port
Connected to a device to transmit data.
USB 2.0 Port
Connected to a storage device to automatically back up the
conguration le and database. This function is only available
when OC200 is powered by a PoE device.
Reset Button
After the device is initialized, press and hold the button for 5
seconds to reset the device to its factory default settings.
Rear Panel
Installation Guide
Feet
Router
SwitchOC200
Management Device
EAP245EAP225
EAP225-Outdoor
Power On
Via Standard PoE Device
Connect an Ethernet cable from the ETH1 (PoE IN) port of
OC200 to a standard 802.3af or 802.3at PoE device, such as
TP-Link PoE switch.
Via USB Power Source
Connect a USB cable (not provided) from the micro USB port
of OC200 to the USB Power Source (5V DC, minimum 1A).
Power LED
On: Working normally.
O: Working abnormally.
ETH1 (PoE IN) Port
Connected to a standard 802.3af or 802.3at PoE device, such
as a TP-Link PoE switch, to transmit data and gain power
supply simultaneously.
Kensington Security Slot
Kensington Security Slot
Secure the lock (not provided) into the security slot to prevent
the device from being stolen.
Micro USB
Connected to a USB Power Source (5V DC, minimum 1A) to
gain power supply if PoE is not available.
Micro USB
The Cloud LED ashes three times when initialization is
completed.
Software Congurations
OC200 supports two management options:
To configure and manage OC200 without requiring internet access, please refer to Local Management.
To configure and manage OC200 through cloud services, please refer to Remote Management.
Local Management
Via Omada App
1. Download the Omada app on your mobile device. It can be
downloaded from Apple Store or Google Play:
or
Scan for Omada App Download Omada App
2. Make sure that your mobile device and OC200 are on the
same subnet.
3. Launch the app and go to Local Access. Then tap the +
button on the upper-right corner to add OC200.
4. Follow the step-by-step instructions to complete the
conguration wizard.
Remote Management
Via Omada App
1. Make sure that your mobile device and OC200 can access
the internet.
2. Download the Omada app on your mobile device. It can be
downloaded from Apple Store or Google Play:
or
Scan for Omada App Download Omada App
3. Launch the app and go to Cloud Access. Then log in with
your TP-Link ID.
4. Tap the + button on the upper-right corner and follow the
instructions in the app to add OC200.
5. Follow the step-by-step instructions to complete the
conguration wizard.
Via a Web Browser
1. Make sure that your management device and OC200 are on
the same subnet.
2. Check the DHCP server (typically a router) for OC200’s IP
Address. The default fallback IP address is 192.168.0.253.
If you have downloaded the Omada app, you can also
check the app for OC200’s IP address.
The fallback IP address is used when OC200 fails to get
dynamic IP address from the DHCP server.
3. Launch a web browser and type OC200’s IP address in the
address bar, then press Enter (Windows) or Return (Mac).
https://<IP_address>
Via a Web Browser
1. Make sure that your management device and OC200 can
access the internet.
2. Launch a web browser and type https://omada.tplinkcloud.com
in the address bar, then press Enter (Windows) or Return (Mac).
https://omada.tplinkcloud.com
3. Enter your TP-Link ID and password to log in. Then click Add
Cloud Controller and follow the instructions to add your OC200.
4. Click Launch in the Action column to visit the web
management interface of OC200.
4. Click Let’s Get Started and follow the step-by-step
instructions to complete the conguration wizard.
For detailed congurations, please visit
https://www.tp-link.com/support to download the User
Guide of OC200 in the download center.
5. Click Let’s Get Started and follow the step-by-step
instructions to complete the conguration wizard.
For technical support, User Guide and other information, please visit
https://www.tp-link.com/support, or simply scan the QR code.
The products of TP-Link partly contain software code developed by third parties,
including software code subject to the GNU General Public License (“GPL”). As
applicable, the terms of the GPL and any information on obtaining access to the
respective GPL Code used in TP-Link products are available to you in GPL-Code-Centre
under (https://www.tp-link.com/en/support/gpl/). The respective programs are
distributed WITHOUT ANY WARRANTY and are subject to the copyrights of one or more
authors. For details, see the GPL Code and other terms of the GPL.
© 2018 TP-Link
Loading...