COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of TP-LINK Technologies Co., Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK Technologies Co., Ltd. Copyright © 2006 TP-LINK Technologies Co., Ltd. All rights reserved.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
¾Reorient or relocate the receiving antenna.
¾Increase the separation between the equipment and receiver.
¾Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
¾Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference.
(2)This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter”.
CE Declaration of Conformity
For the following equipment: MR0-WR641G
is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (89/336/EEC), Low-voltage Directive (73/23/EEC) and the Amendment Directive (93/68/EEC), the procedures given in European Council Directive 99/5/EC and 89/3360EEC.
The equipment was passed. The test was performed according to the following European standards:
¾EN 300 328 V.1.4.1 (2003)
¾EN 301 489-1 V.1.4.1 (2002) / EN 301 489-17 V.1.2.1 (2002)
¾EN 60950-1: 2001
European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range 2.400-2.4835GHz; In France, the equipment must be restricted to the 2.4465-2.4835GHz frequency range and must be restricted to indoor use.
Package contents.............................................................................................................. |
1 |
|
Chapter 1: About this Guide .............................................................................................. |
2 |
|
1.1 |
Purposes.............................................................................................................. |
2 |
1.2 |
Conventions ......................................................................................................... |
2 |
1.3 |
Overview of this User Guide ................................................................................ |
2 |
Chapter 2: Introduction...................................................................................................... |
3 |
|
2.1 |
Overview of the Router ........................................................................................ |
3 |
2.2 |
Features............................................................................................................... |
3 |
2.3 |
Panel Layout ........................................................................................................ |
4 |
|
2.3.1 The Front Panel ......................................................................................... |
4 |
|
2.3.2 The Rear Panel.......................................................................................... |
5 |
Chapter 3: Connecting the Router .................................................................................... |
6 |
|
3.1 |
System Requirements.......................................................................................... |
6 |
3.2 |
Installation Environment Requirements................................................................ |
6 |
3.3 |
Connecting the Router ......................................................................................... |
6 |
Chapter 4: Quick Installation Guide................................................................................... |
8 |
|
4.1 TCP/IP configuration ............................................................................................ |
8 |
|
4.2 |
Quick Installation Guide ..................................................................................... |
10 |
Chapter 5: Configuring the Router .................................................................................. |
14 |
|
5.1 login ................................................................................................................... |
14 |
|
5.2 |
Status................................................................................................................. |
14 |
5.3 |
Quick Setup ....................................................................................................... |
15 |
5.4 |
Network.............................................................................................................. |
15 |
|
5.4.1 LAN.......................................................................................................... |
16 |
|
5.4.2 WAN......................................................................................................... |
16 |
|
5.4.3 MAC Clone .............................................................................................. |
27 |
5.5 |
Wireless ............................................................................................................. |
28 |
|
5.5.1 Wireless Settings ..................................................................................... |
28 |
|
5.5.2 MAC Filtering ........................................................................................... |
31 |
|
5.5.3 Wireless Statistics .................................................................................... |
34 |
5.6 DHCP................................................................................................................. |
34 |
|
|
5.6.1 DHCP Settings......................................................................................... |
35 |
|
5.6.2 DHCP Clients List .................................................................................... |
35 |
|
5.6.3 Address Reservation................................................................................ |
36 |
5.7 |
Forwarding ......................................................................................................... |
37 |
|
5.7.1 Virtual Servers ......................................................................................... |
37 |
|
5.7.2 Port Triggering ......................................................................................... |
39 |
|
5.7.3 DMZ ......................................................................................................... |
41 |
|
5.7.4 UPnP ....................................................................................................... |
41 |
5.8 |
Security.............................................................................................................. |
42 |
|
5.8.1 Firewall .................................................................................................... |
43 |
|
5.8.2 IP Address Filtering.................................................................................. |
43 |
|
5.8.3 Domain Filtering....................................................................................... |
45 |
|
5.8.4 MAC Filtering ........................................................................................... |
47 |
5.8.5 Remote Management .............................................................................. |
49 |
5.8.6 Advanced Security ................................................................................... |
49 |
5.9 Static Routing..................................................................................................... |
51 |
5.10 DDNS............................................................................................................... |
52 |
5.10.1 Dyndns.org DDNS ................................................................................. |
52 |
5.10.2 Oray.net DDNS...................................................................................... |
53 |
5.10.3 Comexe.cn DDNS.................................................................................. |
54 |
5.11 System Tools .................................................................................................... |
55 |
5.11.1 Time ....................................................................................................... |
55 |
5.11.2 Firmware ................................................................................................ |
56 |
5.11.3 Factory Defaults ..................................................................................... |
57 |
5.11.4 Backup and Restore............................................................................... |
57 |
5.11.5 Reboot ................................................................................................... |
58 |
5.11.6 Password ............................................................................................... |
58 |
5.11.7 Log ......................................................................................................... |
59 |
5.11.8 Statistics................................................................................................. |
59 |
Appendix A: FAQ............................................................................................................. |
61 |
Appendix B: Configuring the PC ..................................................................................... |
65 |
Appendix C: Specifications.............................................................................................. |
70 |
Appendix D: Glossary ..................................................................................................... |
71 |
Appendix E: Contact Information..................................................................................... |
73 |
MR0-WR641G 108M Wireless Router User Guide
The following contents should be found in your box:
¾One MR0-WR641G 108Mbps Wireless Router
¾One AC power Adapter for MR0-WR641G 108Mbps Wireless Router
¾Quick Installation Guide
¾One Resource CD for MR0-WR641G 108Mbps Wireless Router, including:
•This Guide
•Other Helpful Information
Note: If any of the listed contents are damaged or missing, please contact the retailer from whom you purchased the MR0-WR641G 108Mbps Wireless Router for assistance.
- 1 -
MR0-WR641G 108M Wireless Router User Guide
Thank you for choosing the MR0-WR641G 108Mbps Wireless Router. This router provides dedicated solution for Small Office/Home Office (SOHO) networks. With your network all connected, your local wired or wireless network can share Internet access, files and fun for multiple PCs through one ISP account.
It adopts 108M Super G™ WLAN Transmission Technology, which offers the highest throughput performance available on the market today, and data rates of up to 108Mbps. In dynamic 108M mode, the router can attach IEEE 802.11b, 802.11g and 108Mbps Super G™ devices at the same time in an integrated environment.
It adopts 2x to 3x eXtended Range™ WLAN transmission technology so that transmission distance is 2-3 times of traditional IEEE 802.11g/b solutions, up to 855.36m tested in China. Transmission range is extended to 4-9 times.
It is an easy web-based setup for installation and management. Even though you may not be familiar with the router, this guide will make configuring the router easy. Before installing the router, please look through this guide to get to know all the router’s functions.
This Guide tells you how to use the MR0-WR641G 108Mbps Wireless Router.
The router mentioned in this guide stands for MR0-WR641G 108Mbps Wireless Router.
Chapter 1: About this Guide
Chapter 2: Introduction
Chapter 3: Connecting the Router
Chapter 4: Quick Installation Guide
Chapter 5: Configuring the Router
Appendix A: FAQ
Appendix B: Configuring the PC
Appendix C: Specifications
Appendix D: Glossary
Appendix E: Contact Information
- 2 -
MR0-WR641G 108M Wireless Router User Guide
The MR0-WR641G 108Mbps Wireless Router integrates 4-port Switch, firewall, NAT-router and Wireless AP. Its design is dedicated to Small Office/Home Office (SOHO) wireless network solutions. The MR0-WR641G 108Mbps Wireless Router will allow you to connect your network wirelessly better than ever, sharing Internet Access, files and fun, easily and securely.
In the most attentive wireless security, the MR0-WR641G 108Mbps Wireless Router provides multiple protection measures. It can be set to turn off the wireless network name (SSID) broadcast so that only stations that have the SSID can be connected. The router provides wireless LAN 64/128/152-bit WEP encryption security, and WPA/WPA2 and WPA-PSK/WPA2-PSK authentication, as well as TKIP/AES encryption security. It also supports VPN pass-through for sensitive data secure transmission.
The MR0-WR641G 108Mbps Wireless Router complies with the IEEE 802.11g/b standards and adopts 108M Super G™ WLAN transmission technology so that the data transmission rate is up to 108Mbps. It adopts 2x to 3x eXtended Range™ WLAN transmission technology so that transmission distance is 2-3 times that of traditional IEEE 802.11g/b solutions, up to a distance of 855.36m tested in China. Transmission range is extended to 4-9 times. It is compatible with all IEEE 802.11g and IEEE 802.11b products.
The MR0-WR641G 108Mbps Wireless Router provides flexible access control so that parents or network administrators can establish restricted access policies for children or staff. It has built-in NAT and DHCP server supporting static IP address distributing. It also supports Virtual Server and DMZ host for Port Triggering needs, and remote management and log so that network administrators can manage and monitor the network in real time.
The MR0-WR641G 108Mbps Wireless Router is easy-to-manage. Quick Setup is supported and friendly help messages are provided for every step. So you can configure it quickly and share Internet access, files and fun.
¾Complies with IEEE 802.11g, IEEE 802.11b, IEEE 802.3, IEEE 802.3u standards.
¾1 10/100M Auto-Negotiation RJ45 WAN port, 4 10/100M Auto-Negotiation RJ45 LAN ports,
¾supporting Auto MDI/MDIX.
¾Adopts 2x to 3x eXtended Range™ and 108M Super G™ wireless LAN transmission technology.
¾Supports 108/54/48/36/24/18/12/9/6Mbps or 11/5.5/3/2/1Mbps data transfer rates.
¾Provides WPA/WPA2, WPA-PSK/WPA2-PSK authentication, TKIP/AES encryption security.
¾Shares data and Internet access for users, supporting PPPoE, Dynamic IP, Static IP, L2TP, PPTP, BigPond Cable Internet access.
-3 -
MR0-WR641G 108M Wireless Router User Guide
¾Supports Virtual Server, Special Application and DMZ host.
¾Supports UPnP, Dynamic DNS, Static Routing, VPN Pass-through.
¾Connecting Internet on demand and disconnecting from the Internet when idle for PPPoE.
¾Built-in NAT and DHCP server supporting static IP address distributing.
¾Built-in firewall supporting IP address filtering, Domain Name filtering, and MAC address filtering.
¾Supports connecting/disconnecting from the Internet on a specified time of day.
¾Supports access control, parents and network administrators can establish restricted access policies based on time of day for children or staff.
¾Provides 64/128/152-bit WEP encryption security and wireless LAN ACL (Access Control List).
¾Supports Flow Statistics.
¾Supports ICMP-FLOOD, UDP-FLOOD, TCP-SYN-FLOOD filter.
¾Ignores Ping packets from WAN or LAN ports.
¾Supports firmware upgrade.
¾Supports Web management.
The front panel of the MR0-WR641G consists of several LED indicators, which is designed to indicate connections. View from left. Table 2-1 describes the LEDs on the front panel of the router.
|
|
Figure 2-1 Front Panel sketch |
|
|
|
|
|
Name |
Action |
|
Description |
PWR |
Not lit |
|
No Power |
Lit up |
|
Power on |
|
|
|
||
|
Lit up |
|
The router is initializing |
SYS |
Flashing |
|
The router is working properly |
|
Not lit |
|
The router has a hardware error |
WLAN |
Not lit |
|
There is no wireless device linked to the device |
Flashing |
|
The Wireless function is enabled |
|
|
|
||
|
Not lit |
|
There is no device linked to the corresponding port |
WAN,1-4 |
Lit up |
|
There is a device linked to the corresponding port but no |
|
activity |
||
|
|
|
|
|
Flashing |
|
There is an active device linked to the corresponding port |
|
|
Table 2-1 The LEDs description |
- 4 -
MR0-WR641G 108M Wireless Router User Guide
The rear panel contains the following features. (View from left to right)
¾AC power socket: only use the power adapter supplied with the MR0-WR641G 108Mbps Wireless Router, use of a different adapter may result in product damage.
¾Four 10/100Mbps RJ45 LAN ports for connecting the router to the local PCs
¾RJ45 WAN port for connecting the router to a cable, DSL modem, or Ethernet
¾Factory Default Reset button
¾There are two ways to reset the router's factory defaults:
1)Use the Factory Defaults function on System Tools -> Factory Defaults page in the router's Web-based Utility.
2)Use the Factory Default Reset button: First, turn off the router's power. Second, press and hold the default reset button then turn on the router's power, until the SYS LED lights up (about 3 seconds). Last, release the reset button and wait for the router to reboot.
Note: Ensure the router is powered on before it restarts completely.
¾Wireless antenna
Figure 2-2 Rear Panel sketch
- 5 -
MR0-WR641G 108M Wireless Router User Guide
¾Broadband Internet Access Service (DSL/Cable/Ethernet)
¾One DSL/Cable modem that has an RJ45 connector (you do not need it if you connect the router to the Ethernet)
¾Each PC in the LAN needs a working Ethernet Adapter and an Ethernet cable with RJ45 connectors
¾TCP/IP protocol must be installed on each PC
¾Web browser, such as Microsoft Internet Explorer 5.0 or later, Netscape Navigator 6.0 or later
¾Do not place in direct sunlight or near a heater or heating vent
¾Do not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on all sides of the router
¾Well ventilated (especially if it is in a closet)
¾Operating temperature: 0 ~40 (32 ~104 )
¾Operating Humidity: 10%~90%RH, Non-condensing
Before you install the router, you should connect your PC to the Internet through your broadband service successfully. If there is any problem, please contact your ISP. After that, please install the router according to the following steps. Don't forget to pull out the power plug and keep your hands dry.
1.Power off your PC, Cable/DSL modem, and the router.
2.Locate an optimum location for the router. The best place is usually near the center of the area in which your PC will wirelessly connect. The place must accord with the Installation Environment Requirements..
3.Adjust the direction of the antenna. Normally, upright is a good direction.
4.Connect the PCs and each Switch/Hub in your LAN to the LAN Ports on the router, shown in figure 3-1. (If you have the wireless NIC and want to use wireless connector, you can skip this step.)
5.Connect the DSL/Cable Modem to the WAN port on the router, shown in figure 3-1.
6.Connect the AC power adapter to the AC power socket on the router, and the other end into an electrical outlet. The router will start to work automatically.
7.Power on your PC and Cable/DSL modem.
- 6 -
MR0-WR641G 108M Wireless Router User Guide
Figure 3-1 Hardware Installation of the MR0-WR641G 108Mbps Wireless Router
- 7 -
MR0-WR641G 108M Wireless Router User Guide
After connecting the MR0-WR641G Router into your network, you should configure it. This chapter describes how to configure the basic functions of your MR0-WR641G Wireless Router. These procedures only take you a few minutes. You can access the Internet via the router immediately after successfully configuring.
The default IP address of the MR0-WR641G 108Mbps Wireless Router is 192.168.1.1. And the default Subnet Mask is 255.255.255.0. These values can be seen from the LAN. They can be changed as you desire, as an example we use the default values for description in this guide.
Connect the local PC to the LAN ports of the router. There are then two ways to configure the IP address for your PC.
¾Configure the IP address manually
1)Set up the TCP/IP Protocol for your PC. If you need instructions as to how to do this, please refer to Appendix B: "Configuring the PC."
2)Configure the network parameters. The IP address is 192.168.1.xxx ("xxx" is from 2 to 254), Subnet Mask is 255.255.255.0, and Gateway is 192.168.1.1 (The router's default IP address)
¾Obtain an IP address automatically
1)Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC. If you need instructions as to how to do this, please refer to Appendix B: "Configuring the PC."
2)Power off the router and PC. Then turn on the router and restart the PC. The built-in DHCP server will assign IP address for the PC.
Now, you can run the Ping command in the command prompt to verify the network connection between your PC and the router. The following example is in Windows 2000 OS.
Open a command prompt, and type ping 192.168.1.1, then press Enter.
If the result displayed is similar to that shown in figure 4-1, the connection between your PC and the router has been established.
- 8 -
MR0-WR641G 108M Wireless Router User Guide
Figure 4-1 Successful result of Ping command
If the result displayed is similar to that shown in figure 4-2, it means that your PC has not connected to the router.
Figure 4-2 Failed result of Ping command
Please check it following these steps:
1.Is the connection between your PC and the router correct?
Note: The 1/2/3/4 LEDs of LAN port which you link to on the router and LEDs on your PC's adapter should be lit.
2.Is the TCP/IP configuration for your PC correct?
Note: If the router's IP address is 192.168.1.1, your PC's IP address must be within the range of 192.168.1.2 ~ 192.168.1.254, the gateway must be 192.168.1.1
- 9 -
MR0-WR641G 108M Wireless Router User Guide
With a Web-based (Internet Explorer or Netscape® Navigator) utility, it is easy to configure and manage the MR0-WR641G 108Mbps Wireless Router. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a web browser.
Connect to the router by typing http://192.168.1.1 in the address field of web browser.
Figure 4-3 Login the router
After a moment, a login window will appear similar to that shown in Figure 4-4. Enter admin for the User Name and Password, both in lower case letters. Then click the OK button or press the Enter key.
Figure 4-4 Login Windows
Note: If the above screen does not pop-up, it means that your web-browser has been set to a proxy. Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it.
If the User Name and Password are correct, you can configure the router using the web browser. Please click the Quick Setup link on the left of the main menu and the Quick Setup screen will appear.
Figure 4-5 Quick Setup
- 10 -
MR0-WR641G 108M Wireless Router User Guide
Click Next, then Choose WAN Connection Type page will appear, shown in figure 4-6.
Figure 4-6 Choose WAN Connection Type
The router supports three popular ways to connect to Internet. Please select one compatible with your ISP. Click Next to enter the necessary network parameters.
If you choose "PPPoE", you will see this page shown in figure 4-7:
Figure 4-7 Quick Setup - PPPoE
¾User Name and Password - Enter the User Name and Password provided by your ISP. These fields are case sensitive. If you have difficulty with this process, please contact your ISP.
If you choose "Dynamic IP", the router will automatically receive the IP parameters from your ISP without needing to enter any parameters.
If you Choose "Static IP", the Static IP settings page will appear, shown in figure 4-8:
Figure 4-8 Quick Setup - Static IP
Note: The IP parameters should have been provided by your ISP.
¾IP Address - This is the WAN IP address as seen by external users on the Internet
-11 -
MR0-WR641G 108M Wireless Router User Guide
(including your ISP). Enter the IP address into the field.
¾Subnet Mask - The Subnet Mask is used for the WAN IP address, it is usually 255.255.255.0
¾Default Gateway - Enter the gateway IP address into the box if required.
¾Primary DNS - Enter the DNS Server IP address into the boxes if required.
¾Secondary DNS - If your ISP provides another DNS server, enter it into this field.
After you complete the above, click Next, the Wireless settings page will appear, shown in figure 4-9.
Figure 4-9 Quick Setup - Wireless settings
In this page, you can configure the following wireless parameters:
¾Wireless Radio - Indicates whether the Access Point feature of the router is enabled or disabled. If disabled, the WLAN LED on the front panel will not be lit and the wireless stations will not be able to access the router. If enabled, the WLAN LED will be lit up and wireless stations will be able to access the router.
¾SSID - Enter a value of up to 32 characters. The same SSID must be assigned to all wireless devices on your network. The default SSID is TP-LINK. This value is case-sensitive. For example, TP-LINK is NOT the same as tp-link.
¾Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the router can be used. It may be illegal to use the wireless function of the router in a region other than one of those specified in this field.
¾Channel - The current channel in use. This field determines which operating frequency will be used.
¾Mode - Indicates the current mode (108Mbps (Dynamic), 108Mbps (Static), 54Mbps (802.11g), 11Mbps (802.11b)). If you select 108Mbps (Dynamic), it is compatible with 54Mbps (802.11g) and 11Mbps (802.11b). If you select 54Mbps (802.11g), it is compatible with 11Mbps (802.11b).
These settings are only for basic wireless parameters, for advanced settings, please refer to Section 5.5: "Wireless."
Note: The change of wireless settings won't take effect until the router reboots! You can reboot it manually. If you need instructions as to how to do this, please refer to Section 5.11.5: "Rebooting the Router"
- 12 -
MR0-WR641G 108M Wireless Router User Guide
Click the Next button, you will then see the Finish page:
Figure 4-10 Quick Setup - Finish
After finishing all configurations of basic network parameters, please click Finish button to exit this Quick Setup.
- 13 -
MR0-WR641G 108M Wireless Router User Guide
This chapter describes each web page's key functions.
After your successful login, you can configure and manage the router. There are ten main menus on the left of the web-based utility. Submenus will be available after you click one of the main menus. The ten main menus are: Status, Quick Setup, Network, Wireless, DHCP, Forwarding, Security, Static Routing, DDNS and System Tools. On the right of the web-based utility, there are the detailed explanations and instructions for the corresponding page. To apply any settings you have altered on the page, please click the Save button.
The detailed explanations for each web page key’s function is listed below.
The Status page displays the router's current status and configuration. All information is read-only.
1.LAN
This field displays the current settings or information for the LAN, including the MAC address, IP address and Subnet Mask.
2.Wireless
This field displays basic information or status for wireless function, including Wireless
Radio, SSID, Channel, Mode, Wireless MAC address and IP address.
3.WAN
These parameters apply to the WAN port of the router, including MAC address, IP address, Subnet Mask, Default Gateway, DNS server and WAN connection type. If PPPoE is chosen as the WAN connection type, the Disconnect button will be shown here while you are accessing the Internet. You can also cut the connection by clicking the button. If you have not connected to the Internet, just click Connect to establish the connection.
4.Traffic Statistics
This field displays the router's traffic statistics.
5.System Up Time
The amount of time from when the router was switched on or reset.
- 14 -
MR0-WR641G 108M Wireless Router User Guide
Figure 5-1 Router Status
Please refer to Section 4.2: "Quick Installation Guide."
Figure 5-2 the Network menu
- 15 -
MR0-WR641G 108M Wireless Router User Guide
There are three submenus under the Network menu (shown in figure 5-2): LAN, WAN and MAC Clone. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below.
5.4.1 LAN
You can configure the IP parameters of LAN on this page.
Figure 5-3 LAN
¾MAC Address - The physical address of the router, as seen from the LAN. The value can't be changed.
¾IP Address - Enter the IP address of your router in dotted-decimal notation (factory default: 192.168.1.1).
¾Subnet Mask - An address code that determines the size of the network. Normally use 255.255.255.0 as the subnet mask.
Note:
a.If you change the IP Address of LAN, you must use the new IP Address to login the router.
b.If the new LAN IP Address you set is not in the same subnet, the IP Address pool of the DHCP server will not take effect, until they are re-configured.
c.If the new LAN IP Address you set is not in the same subnet, the Virtual Server and DMZ Host will change accordingly at the same time.
5.4.2 WAN
You can configure the WAN port parameters on this page.
First, please choose the WAN Connection Type (Dynamic IP/Static IP/PPPoE/802.1X + Dynamic IP/802.1X + Static IP/BigPond Cable/L2TP/PPTP) for Internet. The default type is Dynamic IP. If you aren’t given any login parameters (fixed IP Address, logging ID, etc), please select Dynamic IP. If you are given a fixed IP (static IP), please select Static IP. If you are given a user name and a password, please select the type of your ISP provided(PPPoE/BigPond/L2TP/PPTP). If you are not sure which connection type you use currently, please contact your ISP to obtain the correct information.
1.If you choose Dynamic IP, the router will automatically get IP parameters from your ISP. You can see the page as follows (figure 5-4):
-16 -
MR0-WR641G 108M Wireless Router User Guide
Figure 5-4 WAN – Dynamic IP
This page displays the WAN IP parameters assigned dynamically by your ISP, including IP address, Subnet Mask, Default Gateway, etc. Click the Renew button to renew the IP parameters from your ISP. Click the Release button to release the IP parameters.
MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. For some ISPs you need to reduce the MTU. But this is rarely required, and should not be done unless you are sure it is necessary for your ISP connection.
If your ISP gives you one or two DNS addresses, select Use These DNS Servers and enter the primary and secondary addresses into the correct fields. Otherwise, the DNS servers will be assigned dynamically from your ISP.
Note: If you get address and find error when you go to a Web site, it is likely that your DNS servers are set up improperly. You should contact your ISP to get DNS server addresses.
Get IP with Unicast DHCP - A few ISPs' DHCP servers do not support the broadcast applications. If you cannot get the IP Address normally, you can choose this option. (This is rarely required.)
2.If you choose Static IP, you should have fixed IP Parameters specified by your ISP. The Static IP settings page will appear, shown in figure 5-5:
-17 -
MR0-WR641G 108M Wireless Router User Guide
Figure 5-5 WAN - Static IP
You should type the following parameters into the spaces provided:
¾IP Address - Enter the IP address in dotted-decimal notation provided by your ISP.
¾Subnet Mask - Enter the subnet Mask in dotted-decimal notation provided by your ISP, usually is 255.255.255.0.
¾Default Gateway - (Optional) Enter the gateway IP address in dotted-decimal notation provided by your ISP.
¾MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. For some ISPs you may need to modify the MTU. But this is rarely required, and should not be done unless you are sure it is necessary for your ISP connection.
¾Primary DNS - (Optional) Enter the DNS address in dotted-decimal notation provided by your ISP.
¾Secondary DNS - (Optional) Type another DNS address in dotted-decimal notation provided by your ISP if provided.
3.If you choose PPPoE, you should enter the following parameters (figure 5-6):
- 18 -
MR0-WR641G 108M Wireless Router User Guide
Figure 5-6 WAN - PPPoE
¾User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive.
¾Connect on Demand - You can configure the router to disconnect your Internet connection after a specified period of inactivity (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the router to automatically re-establish your connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio button. If you want your Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet connection terminates.
Caution: Sometimes the connection cannot be disconnected although you specify a time to Max Idle Time, since some applications is visiting the Internet continually in the background.
¾Connect Automatically - Connect automatically after the router is disconnected. To use this option, click the radio button.
¾Time-based Connecting - You can configure the router to make it connect or disconnect based on time. Enter the start time in HH:MM format for connecting and end time in HH:MM format for disconnecting in the Period of Time fields.
Note: Only when you have configed the system time on System Tools -> Time page, will the Time-based Connecting function can take effect.
¾Connect Manually - You can configure the router to make it connect or disconnect manually. After a specified period of inactivity (Max Idle Time), the router will disconnect from the Internet connection, and you will not be able to re-establish your connection automatically as soon as you attempt to access the Internet again. To use this option, click the radio button. If you want your Internet connection to remain active at all times, enter "0" in the Max Idle Time field. Otherwise, enter the number
-19 -
MR0-WR641G 108M Wireless Router User Guide
time in minutes that you wish to have the Internet connecting last unless a new link is requested.
Caution: Sometimes the connection cannot be disconnected although you specify a time to Max Idle Time, since some applications are visiting the Internet continually in the background.
Click the Connect button to connect immediately, Click the Disconnect button to disconnect immediately.
Click the Advanced Settings button to set up the advanced option, the page shown in figure 5-7 will then appear:
Figure 5-7 PPPoE Advanced Settings
¾Packet MTU - The default MTU size is 1492 bytes, which value is usually fine. For some ISPs, you need modify the MTU. This should not be done unless you are sure it is necessary for your ISP.
¾Service Name/AC Name - The service name and AC (Access Concentrator) name, these should not be configured unless you are sure it is necessary for your ISP.
¾ISP Specified IP Address - If you know that your ISP does not automatically transmit your IP address to the router during login, click “Use the IP Address specified by ISP” check box and enter the IP Address in dotted-decimal notation, which your ISP provided.
¾Detect Online Interval - The default value is 0, you can input the value between 0 and 120. The router will detect Access Concentrator online at every interval between seconds. If the value is 0, it means, do not detect.
¾DNS IP address - If you know that your ISP does not automatically transmit DNS addresses to the router during login, click “Use the following DNS servers” checkbox and enter the IP address in dotted-decimal notation of your ISP’s primary DNS server. If a secondary DNS server address is available, enter it as well.
-20 -