Topcon FC-5000 Owner's Manual

owner’s manual

owner’s manual

©

Copyright March 2016 Topcon, Inc All rights reserved.

Information is subject to change without notice.

Topcon® is a registered trademarks of Topcon, Inc. FC-5000™
Ruggedized Field Computer is a recognized trademark of
Topcon, Inc.

Windows, Windows 10, Windows 8.1, and the Windows
logo are trademarks or registered trademarks of Microsoft
Corporation in the United States and/or other countries.

The Bluetooth® word mark is owned by the Bluetooth SIG,
Inc. Any use of such marks by Topcon, Inc. is under license.

Adobe® Acrobat® and Adobe® Reader® are registered
trademarks of Adobe Systems Incorporated in the United
States and/or other countries.

The names of other companies and products mentioned
herein may be the trademarks of their respective owners.

This product manufactured by Juniper Systems, 1132 West
1700 North, Logan, Utah, 84321. Phone [phone].

WARNING! This symbol indicates that failure to follow

!

directions could result in serious injury.

CAUTION: This symbol indicates that failure to follow

!

directions could result in damage to equipment or loss of
information.

Part Number 25357-00 JS, 1013583-02 Topcon

Topcon Positioning Systems, Inc.

tel: [phone]

7400 National Drive, Livermore, CA 94550

ii FC-5000 Ruggedized Field Computer Owner’s Manual

web: www.topconpositioning.com

l

Contents

1 Getting Started 1

Operating System Languages and Document
Updates 8

2 Standard Features 9

Windows 10 Pro Operating System 10
Display and Touchscreen 10
Keypad Features 12
Power Management 13
LED Activity Indicators 16
Light Sensor 16
Connector Ports 18
Audio Features 18
Sleep, Reset, Hibernate, Power-Off, and Recovery 18
Sensors 21

Bluetooth® Wireless Communication 21

Wi-Fi Wireless Networking 22

3 Optional Features 23

GPS/GNSS 24
Camera 25
4G LTE Data Modem 25
Wireless Safety 27

A Storage, Maintenance, and Recycling 29

Storing the FC-5000 and Battery Pack 30
Protecting the Touchscreen 31
Recycling the FC-5000 and Batteries 31

B Warranty and Repair Information 33

Limited Product Warranty 34
Complete Care Service Plans 37

Contents iii

C Warnings, Regulatory Information, Licensing 39

Product Warnings 40
Certications and Standards 42
Licensing Information 45

D Specications 47

Index 55

iv FC-5000 Ruggedized Field Computer Owner’s Manual

1

Getting Started

Getting Started

The standard features for the FC-5000 Ruggedized Field
Computer from Topcon include a 7” display, capacitive
touchscreen, keypad, Bluetooth, and Wi-Fi. Standard
accessories include a removable lithium-ion battery pack,
an internal battery pack, AC wall charger, hand strap,

connector port cover, and a ne tip capacitive stylus and

tether. Options include front and rear cameras, GPS/GNSS,
and a cellular data modem.

The Anatomy of the FC-5000

Front and Back Features

2

1

6

5

4

3

1 Ambient Light Sensor

2 Front Facing Camera Lens,

2 MP

3 Keypad

4 Power Key

5 Notication LEDs

6 Touchscreen and Display

7 Protective Over-molded

Bumper (all four edges)

7

8

8 Microphone (one on each

side)

9 Rear Facing Camera Lens,

8 MP

10 Camera Flash

11 Speaker

12 Battery Door Lock

13 Door to Removable

Battery Compartment and
Card Slots

14 External Device

Attachment Point (1 of 3
on the back)

15 Location of Internal

10

2 FC-5000 Ruggedized Field Computer Owner’s Manual

13

14

15

16

12

11

9

Battery (not user
accessible)

16 Stylus Storage Slot

Battery Compartment and Card Slots

1

3
4

5
6

2

7

1 Battery Pack, Removable

2 Battery Door

3 Micro SIM Card Slot and

Micro SD/SDHC Card Slot
(underneath card retainer)

4 Flexible Card Retainer

5 Battery Compartment

6 Docking Connection

7 Hand Strap Attachment

Point (2 on each side)

Connector Ports

1 Connector Ports

2 Connector Port Protector

1

2

3 4 5

6

3 12 V DC Power Input Jack

4 USB 3.0 Host, Full Size

5 Microphone/Speaker Jack

6 Stylus Storage Slot

Note: Your FC-5000 might look different than these images,

Perform Initial Tasks

When you receive your FC-5000, perform the tasks outlined

in this section before rst use.

Review Documentation

The owner’s manual, quick start guide, and Microsoft®
License Agreement are available in multiple languages.
Other documents like release notes are available in English.

Chapter 1 Getting Started 3

These documents are located on our website at: htt p ://

TO ENSURE DOO R SEAL, IN SERT SIDE (A ) FIRST!

PARA VEDAR A P ORTA, INSIR A O LADO (A) PR IMEIRO!

PARA SELL AR LA PUERTA , INSERTE PRI MERO LADO ( A)

ERST SEITE ( A) EINLEGEN – S ICHERT TÜRD ICHTUNG!

P/ VEDAR A PORTA, IN SIRA O LAD O (A) PRIMEI RO!

(A)

(A)

topconcare.com/en/hardware/eld_controllers/topcon-

fc-5000. You will need to have an active Topcon Total Care

account to download information from this site. View,
download, and print documents as desired. (Adobe Reader
must be installed on your computer. It is available from
Adobe’s website at: www.adobe.com.)

Documentation will be updated during the life of the FC-

5000. Compare version numbers to see if a document has
changed.

Install the Battery Pack, Micro SD Card, and Micro SIM
Card

The FC-5000 comes with a rechargeable and removable
Li-Ion battery pack. Install and charge the battery pack as
follows:

1. The battery compartment is accessed from the back of
the tablet. Push the battery lock switch in, slide it to the
unlocked position, and remove the door.

!

CAUTION: The FC-5000 is not sealed against water and
dust when the battery door is not installed.

2. If you are using a micro SD card for additional memory
or a micro SIM card with the Cellular Data Modem
(optional), you can install them now before you install
the battery pack or at another time. If you do this,

make sure you replace the exible card retainer before

installation of the battery. See Chapter 2, Standard
Features, SD Cards for more details.

3. Follow the graphic on the battery label to insert the
battery pack properly.

4 FC-5000 Ruggedized Field Computer Owner’s Manual

Hold the battery so that the black tab on the front edge

of the battery is up and facing the door latch (this tab
helps you pull the battery out). Place the back edge

in rst, gently pushing it underneath the two battery

catches. Rotate the front edge down until it is in position.

!

CAUTION: Do not set the battery pack straight down.
Damage to the unit could occur.

Black Tab

4. Replace the door and press down on it until the latch
pops into the locked position.

5. Attach the appropriate plug for your country into the
AC wall charger and plug into a wall socket. Plug the
other end into the DC power jack on the FC-5000.

Note: Use the AC wall charger that came with the FC­5000 or an approved charger. See Appendix C, Wall
Charger Warnings, for details.

6. Charge the battery pack at room temperature (68° F or

20° C) for 6 hours (for the rst charge). While the battery

pack is charging, the red LED blinks. When it is fully

charged and external power is applied, the red LED is

solid.

Note: If you have an optional internal battery as well as
a removable battery, the FC-5000 will not recognize the
internal batter y until the FC-5000 is being charged and
is powered on.

Chapter 1 Getting Started 5

Perform Set Up

1. Press the power key . The tablet powers on and begins

the startup process. The rst time the FC-5000 is turned

on, a Getting ready screen comes up with a progress
indicator. This process can take a few minutes

2. Windows setup menus are presented for rst time set up.

- Pick your language (only those we have translated

the operating system into are listed here; for other

languages, see the next section), country, app

language, keyboard preference, and time zone.

- Read and accept the license agreement.

- To nish the setup process, you need internet access.

Pick the network you want to use. For Cellular, you
need to insert a SIM card (see Chapter 3, Optional
Features, 4G LTE Data Modem for details). For Wi-Fi,
you may need a security key.

- Select Express settings.

- Select the owner of the PC, My organization or I own it.

- If you selected My organization, choose how you will

connect to their infrastructure. In most situations, you
want to select Domain. We suggest you check with
your IT department. If you select yourself, go to the

next step.

- Connect to an existing Microsoft user account or

establish one. You can also chose to do this later if you
prefer.

2. You might be asked to restart the tablet to complete
installation.

3. The Microsoft Start screen appears in Tablet mode,
which shows the Windows Start Menu with prominent
app tiles. Select the symbol in the upper left screen
to see the full Start Menu. If you prefer the traditional
desktop view, open the Action Center and select Tablet
mode which toggles it off. It stays off unless you toggle it
back on.

Attach the Hand Strap and Stylus Tether

A hand strap, ne tip capacitive stylus, and tether are

included with the FC-5000.

6 FC-5000 Ruggedized Field Computer Owner’s Manual

To attach the hand strap and tether to the FC-5000, follow
the diagrams below. You can attach them to the right or left
side of the tablet:

1

2

3

1. Attach one end of the stylus tether to the stylus. To
attach the tether to the tablet, follow these steps:

2. Push the free tether loop through one of the tether
attachment points located on the side of any of the four
corners.

3. Insert the stylus with the attached tether through this
loop and tighten the loop.

4. Place the stylus into the stylus storage slot located on
the bottom of the FC-5000.

Chapter 1 Getting Started 7

Operating System Languages and Document Updates

Install the Operating System in Other Languages

During the Windows set up process, you selected English or
one of the languages that the operating system has been
translated into, including the unique FC-5000 operating
system features. Other languages are also available,
however the unique FC-5000 operating system features are
shown in English and not the language selected.

From the Start screen, go to Settings > Time & Language >
Region & Language. Select your country or region from the
pull down list. Select the + symbol to see a list of possible
languages you can select from. You can also go to related
settings and make additional location related adjustments.

Updates to Technical Documents

Periodically check for updates to documentation associ­ated with the FC-5000 on our website at http://topconcare.

com/en/hardware/eld_controllers/topcon-fc-5000 . Com-

pare part numbers or dates to see if you have the most
recent version of these documents.

8 FC-5000 Ruggedized Field Computer Owner’s Manual

2

Standard Features

Standard Features

This chapter discusses the standard features included with
every model of the FC-5000 rugged tablet.

Windows 10 Pro Operating System

The FC-5000 has the Windows 10 Pro operating system.
If you are not familiar with this operating system, we
recommend that you go to the Start menu > Get Started
(you need internet access to do this). Watch the videos and

read the text to familiarize yourself with Windows 10. You

can also go to Microsoft’s website from another computer
to learn about Windows 10.

Windows Start Menu

Press the Windows logo key or screen icon to open the
Start menu. All applications are listed here and you can
select Settings and File Explorer. Tiles provide easy access to
apps and can be customized.

Action Center

The Action Center provides quick controls, notications,

and messages. To view the Action Center, select the
Action Center icon on the bottom tray (located on the
far right end) or, from the right edge of the screen, swipe
left towards the center of the screen. The Action Center is
shown on the right hand side. Tiles are shown at the bottom.
Some are toggles like Tablet mode, which toggles between
Tablet mode and the traditional desktop mode. Some tiles
take you to other screens where you can take action, like
Notes, or view other menus like All settings.

View System Information for Your FC-5000

To view information about your FC-5000 like the operating
system edition and OS build, go to the Action Center. Select
All Settings > System > About.

Display and Touchscreen

The FC-5000 has a bright color display and capacitive
touchscreen with a diagonal viewing area of 7 inches
(178 mm). It is easy to view outdoors and is sealed against
water and dust. The Windows® 10 operating system

10 FC-5000 Ruggedized Field Computer Owner’s Manual

enhances the ability of the FC-5000 to recognize touch

gestures, making it easy to use a nger to make selections
and navigate. You can also use the ne tip capacitive

stylus included with the FC-5000 or optimize it for rain (see

Touchscreen Settings in the next section).

DisplayandTouchscreenProleSettings

Display Settings

To adjust the display settings including the text size,

brightness, and orientation, go to the Action Center and
select All settings > System > Display.

Backlight Brightness

There are a few shortcuts to adjust the display backlight
brightness.

Open the Action Center. Tap the percent tile (sun icon) to
toggle the display backlight brightness up or down in 25%
increments from 0% to 100%. This same tile can be accessed
by tapping the battery icon on the desktop. To simply dim
the backlight, tap the Battery saver tile. Tap it again to
return it to the previous brightness.

Display Magnier

To turn the magnier on, go to the Action Center and select
All settings > Ease of Use > Magnier. Turn the magnier on
and adjust other settings as desired. Once the magnier is

turned on, you can use the + and – symbols on the display
to zoom in and out.

If you use this feature frequently, you can set up a
programmable key to zoom in and out on the display. See
Keyboard Features, Programmable Keys later in this chapter
for more information.

Touchscreen Prole Settings

The touchscreen prole default is nger and stylus use. The
prole can be adjusted to wet, optimal nger, or optimal
stylus from the Touchscreen Proles app.

To adjust the touchscreen prole, go to the Start menu

and select Touchscreen Proles (located at the bottom of
the Start menu screen in a tile). Select the prole you want

the screen optimized for: nger and stylus (default), nger,

Chapter 2 Standard Features 11

stylus, or wet conditions. As the new prole loads, a progress

bar is shown. Do not interrupt the loading process. You can

try different proles to see which one works best for you.

Calibration Tool - Do Not Use

The calibration tool in Windows 10 is intended for a
resistive touchscreen. The FC-5000 has a capacitive
touchscreen. If the Windows 10 screen calibration tool is
used, it may degrade touchscreen performance. Topcon
is constantly trying to improve and update the quality and

responsiveness of the different touchscreen proles.

Keypad Features

The FC-5000 has several programmable function keys, a
power/suspend key, windows key, and a navigation pad.
The keys are sealed and have backlight illumination. Some
keys are programmable.

Key Function

Windows Start screen

p1 Volume down (programmable)

p2 Volume up (programmable)

Enter (return)

Move left

Move right

Move up

Move down

p3 On screen keyboard (programmable)

Enter (return)

12 FC-5000 Ruggedized Field Computer Owner’s Manual

Key Function

Power

 Press and release: On or sleep
 Hold for 5 seconds and pull down screen: Power

off

!

 Hold for 10 seconds: Reset device. CAUTION:

before doing this, see the Sleep, Reset, Hibernate,
Power-Off, and Recovery section in this chapter.

 Hold for 20 seconds: Electrically disconnect the

battery pack(s); to reconnect the batteries, you

are required to plug in the charger or external

!

12 V power. CAUTION: before doing this, see the
Sleep, Reset, Hibernate, Power-Off, and Recovery
section later in this chapter.

Programmable Keys

The p1, p2, and p3, function keys can be set up
programmatically. These keys can also be selected to
launch applications or functions.

To adjust the programmable keys, open the Start menu and
select Keypad Settings (located at the bottom of the Star t

menu screen in a shortcut tile). The Keypad Buttons and
Backlight panel appears. The programmable keys and their

current assignments is shown. Select your preferred function
per key from the drop down menus.

Keypad Backlight Brightness

To adjust the keypad backlight brightness, go to the Start
menu and select Keypad Settings At the bottom of the
Keypad Buttons and Backlight panel is a slider that adjusts
the keypad backlight brightness. You can make the
backlight brighter by moving the slider to the right or turn it
down by moving the slider to the left. Dimming the keypad
backlight saves battery power when the FC-5000 is in use.

Power Management

The FC-5000 runs on battery power. It comes with a Li-Ion
rechargeable and removable battery pack. An internal
battery pack is an option. You can use one type of battery or
both.

Chapter 2 Standard Features 13

Battery Status and Management

To nd out how much battery life you have left, tap on
the battery icon at the bottom of the desktop screen. The
amount of charge left as a percent and the status of each
battery is shown. The cumulative amount of battery life

left for installed batteries and the approximate amount

of time battery power will last is also shown. (This is an

approximation. The amount of time left varies depending

on what you are doing with the unit).

Preserving Battery Power

There are some settings you can adjust to preserve battery
power. From the battery screen, the display backlight
brightness can easily be toggled up or down in 25%
increments from 0% to 100% by tapping the percent tile (see
the sun icon). Tap the Battery saver tile to dim the backlight
or return it to the previous brightness. To make additional
adjustments, select Power and sleep settings. Settings like
how much time passes before the tablet turns off or goes to
sleep and whether or not Wi-Fi stays connected while it is
asleep can be adjusted.

Charging the Battery Pack(s)

For instructions on how to insert and charge the removable
battery pack, refer to the instructions in Chapter 1, Getting
Started. It typically takes 4 to 5 hours to fully charge a battery
pack.

For tablets that have both a removable battery pack and
an optional internal battery pack, the intelligent internal

battery charging circuit rst charges the battery pack with

the least amount of energy. When this battery pack comes
to the same level as the other battery pack, then both
battery packs are charged at the same time until they are
both fully charged.

Battery packs are charged most efciently at room

temperature (68° F or 20° C). They will not charge if it is too
hot or too cold.

We recommend that you keep the tablet battery pack(s)
charging when it is not in use for up to two weeks. When you

14 FC-5000 Ruggedized Field Computer Owner’s Manual

plug the tablet into the wall charger that comes with it, the
batteries are prevented from being overcharged.

CAUTION: Always power off the tablet before removing

!

the battery. Failure to do so may cause loss of data or
damage to the tablet. EXCEPTION: If your tablet has an
internal battery, this caution does not apply. You can
safely remove (hot swap) the removable battery while the
unit is running.

CAUTION: The FC-5000 is not sealed against water and dust

!

when the battery or battery door is not installed properly.

Battery Life

Battery life on a full charge can be 20 hours or more. This
varies depending on whether or not you also have an
optional internal battery, the applications used, backlight
usage, and radio usage. The optional internal battery adds

5-6 extra hours of battery life.

The shelf life of a battery is about one year (they come
from the manufacturer charged to 50%). Battery packs last

approximately 1,000 to 3,000 charging cycles before they

need to be replaced. This is impacted by applications and
environmental factors. The optional internal pack should last
for the life of the FC-5000.

CAUTION: Only use batteries designed for the FC-5000 from

!

an approved vendor. Use of non-approved batteries may
void your product warranty. The FC-5000 must be returned
to the factory for replacement of the optional internal
battery, although the internal battery pack is designed to
last the life of the tablet.

Power States

The FC-5000 runs on battery power, or external power.
If external power is used, a replaceable and/or internal

battery must be installed.

CAUTION: The unit is not designed to run on external power

!

without a battery installed. Doing so can damage internal
components of your unit and void the warranty.

Chapter 2 Standard Features 15

You can adjust some settings to preserve power:

 Turn off the display (suspend) after a set interval.
 Disable radios when not in use.
 Turn down the display and keypad backlights.

LED Activity Indicators

LED activity indicators are located on the front of the FC­5000 in the upper-left corner.

 Red LED, solid: 1) When the FC-5000 is put to sleep or

powered off by pressing the power key (see details
later in this chapter), the red LED is solid until the unit
has successfully completed the process, and then the
red LED turns off. (The battery should not be removed
while the light is solid until the process is complete.) 2)
The AC adapter is plugged in and the battery is full (not
charging). Red LED, blinking: The AC adapter is plugged
in and the battery is in the process of charging.

 Green LED, solid or blinking: Programmable.
 Blue LED, solid or blinking: Programmable.

 Amber Light: Front or rear facing camera is in use.

The green and blue LEDs are in the same location. They
can not be shown simultaneously. These LEDs can be
programmed by a developer. Sample code is available
upon request

Light Sensor

All units have an ambient light sensor located on the front
of the FC-5000 in the upper-right corner. The light sensor
dynamically adjusts the backlight on the display.

You can disable this process and manually control the
display brightness if you prefer. Go to the Start menu
and select Settings > System > Display. Turn off Change

brightness automatically when lighting changes and tap
Apply. To manually adjust the display backlight, tap on

the battery icon at the bottom of the desktop screen. The
display backlight brightness can easily be toggled up or
down in 25% increments from 0% to 100% by tapping the
percent tile (see the sun icon).

16 FC-5000 Ruggedized Field Computer Owner’s Manual

SD Cards

The FC-5000 has a slot for a micro SD card located in the

battery compartment. The card slot and exible card

holder are designed to hold the card securely in place so it
will not come out or disconnect if the tablet is dropped. To
insert or remove a card, follow these step:

1. Power off the tablet.

2. Remove the battery door as outlined in chapter 1.

!

CAUTION: The FC-5000 is not sealed against water and
dust when the battery pack and battery door are not
installed properly.

!

CAUTION: Always power off the tablet before removing
the battery. Failure to do so may cause loss of data or
damage to the tablet. EXCEPTION: If your tablet has an
internal battery, this caution does not apply. You can
safely remove the removable battery while the unit is
running.

3. Remove the battery pack by pulling up on the black tab
on the battery pack.

4. An image on the battery compartment label shows the
correct location and orientation for the SD card (slot on

the right). Pull the exible card holder back out of the

way. Push the card into the slot to insert it.

5. Push the exible card holder back into place, covering

the card slots.

6. Replace the battery pack, and attach the battery door.

To remove the SD card, pull it out. Use tape or an eraser if
you have trouble.

Chapter 2 Standard Features 17

Connector Ports

The FC-5000 has the following jacks and connectors:

1 Connector Ports

2 Connector Protector

1

2

3 4 6

7

5

3 12 V DC Power Input Jack

4 USB Host, Full Size

5 Connector Protector Retainer

6 Microphone/Speaker Jack

7 Stylus/Storage Slot

The connector protector is removable and replaceable.
See your sales representative for if you need a new one. To
remove it, pull it out of the ports, then gently pull the curved
rubber retainers out of the holes they are in. Replace it by
inserting the curved rubber retainers back into the holes.

Note: The connectors are sealed. A connector protector
to not required to prevent water ingress. It protects the
connectors from exposure to excessive dust and dirt.

Audio Features

The FC-5000 has the following audio features (see The
Anatomy of the FC-5000 images for the locations of these

items):

 Speaker - The speaker provides audible indicators

and program feedback. You can listen to mono audio
les and watch video. For stereo audio, use Bluetooth,
headphones or HDMI output from the optional dock.

 Microphone - Use the microphone to record audio notes

or add sound to a video when using the camera (option).
Built in microphones can also be used for Skype calls.

 Audio Jack - The audio jack supports a stereo headset

or headset/microphone combination with 3.5 mm
connections.

Sleep, Reset, Hibernate, Power-Off, and Recovery

Putting the FC-5000 to Sleep

The FC-5000 goes to sleep after 10 minutes by default. When

18 FC-5000 Ruggedized Field Computer Owner’s Manual

the tablet is in a sleep state, it is still powered up, but in a low
power state.

1. To put the FC-5000 to sleep, press and release the
power key or go to the Start menu, select the Power
symbol, and select Sleep. Going into a sleep state can
take several seconds, depending on which activities the
tablet is working on at the time. While it is going to sleep,
the red LED remains lit.

2. To wake the tablet from a sleep state, press and release
the power key again. When it is awakened, the tablet
quickly resumes where it was before it was put to sleep.

3. You can change the sleep default setting by going to
the Start menu and selecting Settings > System > Power
and Sleep > Sleep.

Hibernating the FC-5000

The FC-5000 can be set up to hibernate, which powers
down the FC-5000. The state of the tablet is saved to a

special le. When the tablet is powered up, the unit boots,
sees the special le, and restores everything to the state

it was in before it hibernated. This is a safer choice versus

sleep if battery power is a concern. For example, your

battery is fairly consumed, but you won’t have access to the
charger for a while. Hibernate will stretch your battery life
out.

By default, when the FC-5000 is powered off, it goes to
sleep. You can change this setting to hibernate (or other
options).

Open the Start menu and select Settings, then go to System

> Power and sleep. At the bottom of the screen under
Related settings, select Additional power settings > Choose
what the power button does. Under Power button settings,
When I press the power button: select Hibernate from the
pull down lists for the On battery and Plugged in options.

Powering Off and On the FC-5000

To preserve battery power, we recommend you power off
the FC-5000 if it will not be used over a long weekend or
several days. Remember that when a unit is powered off
it is still operating, though at a low power state, and this
consumes battery power.

Chapter 2 Standard Features 19

CAUTION: Be aware that when the FC-5000 is powered

!

off, it closes all programs and powers down all system
components. If hibernate is not used, all programs are
closed and data may be lost.

1. Save open les, and close any running programs.

2. Go to the Start menu, select the Power symbol, and
select Shut Down. If the Start menu is not available, press
and hold the power key for 5 seconds and slide the
screen that drops down towards the bottom of the FC­5000 screen.

3. On battery power, if typically takes about 30 seconds for
the tablet to completely shut down, although it can take
several minutes.

4. To power on the FC-5000, press the power key.

Ctrl-Alt-Delete Function

Press and hold down the Microsoft key, then press the On
key. A list that includes the Task Manager is shown. Select
Task Manager to see which apps are running. Press More
details at the bottom to view Processes, Performance, and
other items. This can be useful if your FC-5000 is not acting
correctly and you want to do some troubleshooting.

Resetting the FC-5000

If the FC-5000 is unresponsive, slow, or programs won’t
launch, performing a reset might solve the issue. You
might be asked to perform a reset when an application is
installed.

CAUTION: Be aware that during a reset, applications are

!

closed and unsaved work may be lost.

To reset your FC-5000, Go to the Start menu, select the
Power symbol, and select Restart.

FC-5000 is Locked Up

If the FC-5000 is completely stuck and won’t respond or you
cannot get to the Start menu, hold the power key down for

ve seconds to see if that solves it. If that doesn’t work, hold

it down for 10 seconds. This causes a hardware shut off.

20 FC-5000 Ruggedized Field Computer Owner’s Manual

If 10 seconds doesn’t work, hold the power button down for
20 seconds. Batteries are forced to electrically disconnect
from the tablet, causing a complete shut down. The tablet
cannot be powered on again until it is plugged in with the

AC adapter. Keep this in mind if you are in the eld.

CAUTION: Holding the power button down for 20 seconds

!

for a forced disconnect is recommended only as a last
resort. It can be very hard on the system hardware. NEVER
do this to power off or reset a FC-5000.

Recovery Image

You can restore the FC-5000 back to the factory defaults
using the Recovery Image.

Before initiating a recovery, make sure that the tablet is
plugged in. Go to the Start Menu and select Settings >
Update & Security > Recovery > Reset This PC > Get Started.
Choose Keep my les or Remove everything depending on

your personal needs. A verication screen asks you to verify
what you want to do with the existing les.

The recovery process can take up to 3 hours.

Sensors

Compass, Accelerometer, and Gyroscope

The FC-5000 has a built-in compass and accelerometer. The
accelerometer assists the compass in determining direction,

even when the device is not resting at. The gyroscope

senses change in motion. The compass, accelerometer,
and gyroscope can also be used by other user applications.

The sensors in the FC-5000 have been factory calibrated.
Periodic user calibrations helps the compass be calibrated
to the environment it is being used in. A user calibration
consists of moving the device though all orientations and
angles.

Bluetooth® Wireless Communication

The FC-5000 has built-in Bluetooth® wireless technology,
allowing you to connect it to other wireless devices with
Bluetooth tec h nol o gy.

Chapter 2 Standard Features 21

Creating a Partnership/Pairing a Bluetooth Device

To create a partnership between the FC-5000 and another
device with Bluetooth technology:

1. Turn both devices on.

2. Place them within a few feet of each other. (The FC­5000 has long range Bluetooth, but the other device
might not.)

3. Make Bluetooth discoverable on both devices. Bluetooth
on the FC-5000 is off by default. To activate it, open the
Action Center and press and hold the Bluetooth icon.
Select Go to settings.

4. In the Bluetooth settings screen, you should see a list of
all Bluetooth devices within range. Tap on the name of
the device in the list you would like to pair with, then tap
Pair. If prompted, enter the Pin or Passcode of the paired
device. You should now be paired with the device.

Note: If Bluetooth is on and the tablet enters sleep or
hibernate mode, Bluetooth turns off to save batter y power.
The connection is resumed once it powers back on.

Wi-Fi Wireless Networking

The FC-5000 has built-in Wi-Fi wireless networking to

connect to the Internet or an ofce network.

Connecting to a Wi-Fi Network

To use Wi-Fi, you need to be in range of a Wi-Fi access
point to make a connection. When Wi-Fi is turned on (the
default), the FC-5000 automatically starts scanning the area
for available Wi-Fi networks.

From the Action Center, click and hold the Wi-Fi network
icon, then select go to settings. A list of available networks
is shown. Select the network you want to use and enter
the network security key. The FC-5000 remembers the Wi-Fi
network connections created.

Wi-Fi can be turned off and on and settings can be
managed from this set up screen.

22 FC-5000 Ruggedized Field Computer Owner’s Manual

3

Optional Features

Optional Features

This chapter discusses the optional features that can be
included with the FC-5000 rugged tablet.

GPS/GNSS

FC-5000 Geo models have GPS/GNSS with 2 to 5 meter
accuracy. Use Maps to see your location and ensure that
GPS is working. Open the Start menu and select Maps from
the Most used apps list.

GPS/GNSS Support

Integrated GPS/GNSS Support in Windows

The Windows operating system provides built-in support for
GPS/GNSS devices. As part of that support, the Windows
Sensor and Location platform provides a standard way
for GPS/GNSS information to be made available to
applications that have been designed using the Windows
Sensor and Location application programming interfaces
(APIs).

Legacy Support

In addition to the Sensor and Location APIs, legacy
applications that require access to a serial port can access
NMEA data through a serial COM port interface. The name
of the COM port can be found by using Device Manager

and looking under Ports (COM & LPT) for “uBlox Virtual COM
port (COMx) where “x” is the port number allocated on

your device.

GPS/GNSS Accuracy

The GPS/GNSS antenna is under the notication LEDs and

is intended to work in both portrait view and landscape
view. Do not put your hand or another object over this area.
Accuracy could be reduced. The more items between the
antenna and the satellites, the lower the accuracy.

24 FC-5000 Ruggedized Field Computer Owner’s Manual

Camera

FC-5000 Geo models have a front facing camera that is 2
MP and a rear facing camera that is 8 MP.

The camera app is accessed from the Start menu, All apps
> Camera. There is also a camera tile in the Start menu. You
can set up a programmable key to launch the camera app
if you desire. See Chapter 2, Standard Features, Keyboard
Features, Programmable Keys for more information.

Both the still image camera and video camera are
available from this screen. Other options like audio and a

ash are shown at the top of the camera screen.

Audio

You can record sound with videos. From the Video screen,

tap Include audio when recording video les to turn audio

on.

Photo and Video Library

Photographs and videos are automatically stored in the
Pictures folder.

4GLTEData Modem

The 4G LTE data modem is an option for FC-5000 Geo
models, adding Wide Area Network data modem
capability.

This modem supports all major service providers in North
America, Europe, and many other regions of the world.
Refer to frequency bands and modes supported by the

FC-5000 located in Appendix D, Specications, and your

service provider of choice for compatibility.

Set up a Data Account with a Wireless Provider

Contact a wireless provider to set up data service for the
cellular data modem and obtain an account and micro SIM
card. You need to provide the following information when
setting up an account:

Chapter 3 Optional Features 25

1. Billing Information and business ID, such as your Federal

Tax I.D. or VAT number.

2. The wireless services required. Specify that you need
data service only. You do not need voice or messaging
services.

3. You may be asked for the modem’s IMEI number. From
the Start menu, select Settings > Network & Internet >

Cellular. Tap on the Cellular icon, then select Advanced
Options. The IMIE number is listed under Properties.

Install the SIM Card

The card slot and exible card holder are designed to

hold the card securely in place so it will not come out or
disconnect if the tablet is dropped. To insert or remove a
card, follow these step:

1. Power off the tablet (this is a requirement).

2. Remove the battery door as outlined in chapter 1.

CAUTION: The FC-5000 is not sealed against water and

!

dust when the battery door is not installed properly.

3. Remove the battery pack by pulling up on the black tab
on the front of the battery pack.

4. An image on the battery compartment label shows the
correct location and orientation for the SIM card (slot on

the right). Pull the exible card holder back out of the

way. Push the card into the slot to insert it.

26 FC-5000 Ruggedized Field Computer Owner’s Manual

5. Push the exible card holder back into place, covering

the card slots.

6. Replace the battery pack, and attach the battery door.

To remove the SIM card, gently pull it out with tweezers or a
piece of tape.

Note: If the modem was on before shutting the FC-5000

down to insert the SIM card, you are prompted to congure

the data connection when you reboot.

Wireless Safety

RF Interference Issues

It is important to follow any special regulations regarding
the use of radio equipment due in particular to the
possibility of radio frequency (RF), interference. Here are

some examples:

 Switch OFF your cell modem in hospitals and any other

place where medical equipment may be in use.

 Respect restrictions on the use of radio equipment in fuel

depots, chemical plants or where blasting operations are
in progress.

 Operating your cell modem close to inadequately

protected personal medical devices, such as hearing
aids and pacemakers, could be hazardous. Consult the
manufacturers of the medical device to determine if it is
adequately protected.

 Operation of your cell modem close to other electronic

equipment may also cause interference if the equipment
is inadequately protected. Observe any warning signs
and manufacturers’ recommendations.

 Do not place the FC-5000 with a cell modem alongside

computer discs, credit or travel cards, or other magnetic
media. The modem may affect the information
contained on discs or cards.

Chapter 3 Optional Features 27

28 FC-5000 Ruggedized Field Computer Owner’s Manual

A

Storage, Maintenance, and Recycling

Storage, Maintenance, and Recycling

Follow the instructions in this chapter to properly maintain
and recycle the FC-5000.

Storing the FC-5000 and Battery Pack

When the tablet is not being charged and is in a sleep state,
it draws a small amount of power. This power draw is used to
maintain the memory (RAM) of the tablet in the same state it
was in when it was awake. We recommend charging the tablet
each night or weekend when it is in a sleep state.

If the FC-5000 is not charged while in a sleep state and the
battery reaches a low charge, it automatically powers off to
prevent further drain on the battery.

Note: Data and programs are secure as long as they have
been saved, even if the battery pack becomes discharged.
The tablet does not depend on the batter y to store the data
for extended periods.

Storing the FC-5000 for Less Than Two Weeks

To store the tablet for less than two weeks, complete the
following steps:

1. Close all applications.

2. Plug the tablet into the AC wall adapter that was
shipped with your unit.

Storing the FC-5000 for More than Two Weeks

To store the tablet for two weeks or more, complete the
following steps:

1. Charge the battery pack 30 to 50 percent.

2. Close all running programs, and turn off the tablet.

3. Remove the battery pack.

4. If you have an internal battery pack, press and hold the
power button for 20 seconds to disconnect it.

5. Place the battery pack in a cool, dry location.

6. The AC adapter must be plugged in and connected to
the FC-5000 in order to turn it on after storage.

30 FC-5000 Ruggedized Field Computer Owner’s Manual

Protecting the Touchscreen

Protect the touchscreen from impact, pressure, or abrasive
substances that could damage it. To further protect the
touchscreen, apply a screen protector (optional accessory)
using the directions that come with it in the package.

CAUTION: Be sure to replace the screen protector as often

!

as the screen protector instructions recommend.

Cleaning the FC-5000

Make sure the battery door is securely installed. Remove
the screen protector if you want to clean underneath it.
Use warm water, a mild cleaning solution, and a soft bristle
brush to gently clean the FC-5000.

CAUTION: Do not direct a high-pressure stream of water

!

at the device to clean it. This action could break the seal,
causing water to get inside the device and voiding the
wa rra nty.

CAUTION: Exposure to some cleaning solutions may

!

damage your device, including automotive brake cleaner,
isopropyl alcohol, carburetor cleaner, and similar solutions.
If you are uncertain about the strength or effect of a
cleaner, apply a small amount to a less visible location as a
test. If any visual change becomes apparent, promptly rinse
and wash with a known mild cleaning solution or with water.

Recycling the FC-5000 and Batteries

When the FC-5000 reaches the end of its life, it must not be
disposed of with municipal waste. It is your responsibility
to dispose of your waste equipment by handing it over to
a designated collection point for the recycling of waste
electrical and electronic equipment.

The Li-Ion battery packs for your FC-5000 are recyclable.
Avoid placing them in the trash or municipal waste system.

To nd the nearest battery recycling center in the USA,

you can contact the Rechargeable Battery Recycling
Corporation’s at 1-877-723-1297.

Appendix 3 A 31

32 FC-5000 Ruggedized Field Computer Owner’s Manual

B

Warranty and Repair Information

Warranty and Repair Information

Limited Product Warranty

Two Year Warranty

Juniper Systems, Inc (“JS”) warrants that the FC-5000
Ruggedized Field Computer and optional internal battery
shall be free from defects in materials and workmanship,
under normal intended use, for a period of 24 months from

the date of shipment, excepting that this warranty shall not

apply to user replaceable battery packs, media containing
tablet and desktop PC programs, user documentation, and
any accessories

Ninety Day Warranty

JS warrants that the following items shall be free from
defects in materials and workmanship, under normal
intended use, for a period of ninety (90) days from the date
of shipment:

 User replaceable battery packs
 Media containing the FC-5000 and desktop computer

programs

 User documentation
 Accessories

Warranty Exclusions

This warranty shall not apply if:

(i) the product has been set up improperly or has been

improperly installed or calibrated,

(ii) the product is operated in a manner that is not in

accordance with the user documentation,

(iii) the product is used for a purpose other than for which it

was designed,

(iv) the product has been used in environmental conditions

outside of those specied for the product,

(v) the product has been subject to any modication,

alteration, or change by or on behalf of customer

(except and unless modied, changed or altered by JS

or under direct supervision of JS),

34 FC-5000 Ruggedized Field Computer Owner’s Manual

(vi) the defect or malfunction results from misuse or

accident,

(vii) the serial number on the product has been tampered

with or removed, or

(viii) the product has been opened or tampered with in any

way (such as the tamper evident VOID label indicating

certied IP [Ingress Protection] seal area has been

tampered with or removed).

Parts that are excessively worn are not covered under

warranty. These may include, but are not limited to, the

keyboard elastomer and switch matrix, hand straps, and

the touch screen (if applicable).

This warranty is exclusive and JS will not assume and hereby
expressly disclaims any further warranties, whether express

or implied, including, without limitation, any warranty as

to merchantability, tness for a particular purpose, non-

infringement or any warranties arising from the course of

performance, dealing, or usage of trade. JS specically

makes no warranties as to the suitability of its products for
any particular application. JS makes no warranties that

 its products will meet your requirements or will work in

combination with any hardware or applications software
products provided by third parties,

 the operation of its products will be uninterrupted or error

free, or

 all defects in the product will be corrected.

JS shall not be responsible for software, rmware, information,

or memory data contained in, stored on, or integrated with
any products returned to JS for repair, whether under warranty
or not.

Remedy

In the event a defect in materials or workmanship is

discovered and reported to JS within the specied warranty
period, after evaluation by a technician at a certied repair

center, JS will, at its option, repair the defect or replace the
defective part or product. Replacement products may be
new or reconditioned. JS warrants any replaced or repaired

Appendix B Warranty and Repair Information 35

product for a period of ninety (90) days from the date of
return shipment, or through the end of the original warranty
period, whichever is longer.

Limitation of Liability

To the fullest extent allowed by law, the obligation of JS

shall be limited to the repair or replacement of the product.
JS shall in no event be liable for special, incidental, or
consequential, indirect, special or punitive damages of any

kind, or for loss of revenue or prots, loss of business, loss of
information or data, or other nancial loss arising out of or

in connection with the sale, installation, maintenance, use,
performance, failure, or interruption of any product. Any
responsibility and/or liability of JS shall, in connection with a

warranted product, be limited in the maximum amount to

the original purchase price.

Governing Law

This warranty is governed by the laws of Utah, U.S.A. and

excludes the United Nations Convention on Contracts for

the International Sale of Goods. The courts of Utah shall

have exclusive personal jurisdiction in case of any disputes

arising out of or in connection with this warranty.

Warranty Repairs

Warranty information for the FC-5000 Rugged Tablet is
located on our website at http://www.junipersys.com/

Juniper-Systems-Rugged-Handheld-Computers/support/.

You can evaluate and order service plans, check warranty
status, and view warranty terms and conditions.

To obtain warranty repair, paid upgrade, or service on
the FC-5000, submit a Repair (RMA) Request Form on our
website at https://www.junipersys.com/design/junipersys/

rma_request.php and ll out or contact an authorized

repair center within the applicable warranty period.

Standard repair orders and 3-Day Expedite Service repair

orders are valid for 30 days from the date issued. 1-Day

Expedite Service repair orders are valid for 7 days from the

date issued. If you will not be sending the product to us
immediately, please wait to request a repair until closer to
the time when you are ready to send us the product.

36 FC-5000 Ruggedized Field Computer Owner’s Manual

Services and Materials Provided Under Warranty

 Analysis of problem by service technician
 Labor and materials required to x defective parts
 Functional analysis performed after repair
 Shipping costs to return device to customer

JS strives to provide continued full repair services for our

products for ve years or more from the nal production

date of each product model. However, in some rare cases
(depending on the repair need), it may not be possible
to perform a repair due to an unforeseen discontinuation
or lack of supplied parts from third-party vendors. Repair

support for a product may continue beyond ve years if

obtaining replacement parts or tools remains economically
feasible. Our policy is that we will do what is best and most

benecial for our customers and company.

Complete Care Service Plans

We offer service plan options that provide additional

benets through participating repair centers. Services

include:

 Service plan coverage up to ve years from the original

product ship date

 Up to a 50% discount on all charged repairs
 Expedited repairs and return shipping at no additional

charge

 Replacement of worn and/or damaged parts at no

additional charge

 Complete comprehensive coverage to protect your

investment even when accidents occur

 Loaner product option when an expedited repair is not

enough

 Priority support through a personal account specialist

For more information about our Complete Care service
plans, go to our website athttp://www.junipersys.com/

Juniper-Systems-Rugged-Handheld-Computers/support/
War ranty.

Appendix B Warranty and Repair Information 37

Repairs, Upgrades, and Evaluations

CAUTION: Do not attempt to repair the FC-5000 yourself. This

!

action voids the warranty.

Information about repairs, upgrades, and evaluations is
located on our website at http://www.junipersys.com/

Juniper-Systems/support/Repairs. You can locate a repair

center, submit a repair order, check repair status, view terms
and conditions, get shipping instructions, and view lead
times.

Before returning a unit, please get permission by submitting

a repair order from our website and waiting for conrmation

or by contacting a repair center directly. Be prepared to
provide the following information:

 The product serial number. Information about your FC-

5000 is shown when you go to the Action Center and
select All Settings > System > About. The serial number is
located inside the battery compartment as well.

Note: Before opening the batter y door and removing the
battery, see the proper procedure in Chapter 1, Getting
Started and Chapter 2, Power Management.

 Name and shipping address of company/university/

agency.

 Best contact method (phone, fax, email, cell/mobile).
 Clear, highly-detailed description of the repair or

upgrade.

 Credit card/ purchase order number and billing address

(for a repair or upgrade that is not covered by the

standard warranty or an extended warranty policy).

System Information for your FC-5000

You might be asked to provide additional information
about your FC-5000 when you contact a repair center. To
view information like the operating system edition, OS build
and serial number, go to the Action Center and select All
Settings > System > About.

38 FC-5000 Ruggedized Field Computer Owner’s Manual

C

Warnings, Regulatory Information, Licensing

Warnings, Regulatory Information,
Licensing

Product Warnings

Follow the warnings listed below to use the FC-5000 and
accessories safely.

Battery Warnings

WARNING! This device comes with a lithium-ion

!

rechargeable battery pack. To reduce the risk of re or
burns, do not disassemble, crush, puncture, short external
contacts, or expose the battery pack to re.

Do not disassemble or open, crush, bend or deform,
puncture or shred.

Do not modify or remanufacture, attempt to insert foreign

objects into the battery, immerse or expose to water or
other liquids, expose to re, explosion or other hazard.

Only use the battery for the system for which it is specied.

Only use the battery with a charging system that has

been qualied with the system per this standard. Use of an
unqualied battery or charger may present a risk of re,
explosion, leakage, or other hazard.

Do not short circuit a battery or allow metallic conductive
objects to contact battery terminals.

Replace the battery only with another battery that has

been qualied with the system.

Use of an unqualied battery may present a risk of re,
explosion, leakage, or other hazard.

Promptly dispose of used batteries in accordance with local
regulations.

Battery usage by children should be supervised.

Avoid dropping the battery. If the battery is dropped,
especially on a hard surface, and the user suspects
damage, take it to a service center for inspection.

40 FC-5000 Ruggedized Field Computer Owner’s Manual

Improper battery use may result in a re, explosion or other

hazard.

Excell Battery Company Charge Instructions

 2EXL7492 Internal Battery: 3A Constant Current to 4.2V,

4.2V Contant Voltage to termination current of 50mA

 2EXL7493 Removable Battery: 6A Constant Current to

4.2V, 4.2V Constant Voltage to termination current of
100mA

Wall Charger Warnings

WARNING! To reduce the risk of personal injury, electrical

!

shock, re or damage to the equipment:

Plug the wall charger into an electrical outlet that is easily
accessible at all times.

Do not place anything on the wall charger cord or any
of the other cables. Arrange them so that no one may
accidentally step on or trip over them.

Do not pull on a cord or cable. When unplugging the wall
charger from the electrical outlet, pull on the plug, not the
cord.

The AC wall charger must be approved by Topcon, have
an output rating of 12 VDC and a minimum 1.67 A, and

be certied or listed by a nationally recognized testing

laboratory. The adapter provided with the FC-5000 meets

these criteria. Using any other external power source can

damage your product and void your warranty.

Appendix C Warnings, Regulatory Information, Licensing 41

CerticationsandStandards

There are North America and European Union versions of

the FC-5000, with different certications and standards.

United States

In compliance with the FCC rules 47 CFR 15.19(a)(3), the
statements that follow must appear on the device or in the
user documentation.

1. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

2. The device may not cause harmful interference.

3. This device must accept any interference received,
including interference that may cause undesired
operation.

In compliance with the FCC rules, 47 CFR 15.105(b), the

user must be notied that this equipment has been tested

and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and

rece iver.

 Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

42 FC-5000 Ruggedized Field Computer Owner’s Manual

 Consult the dealer or an experienced radio/TV

technician for help.

In compliance with the FCC rules, 47 CFR 15.21, the user

must be notied that changes or modications to the
Rugged Tablet that are not expressly approved by the

manufacturer could void the user’s authority to operate the
equipment.

Only approved accessories may be used with this
equipment. In general, all cables must be high quality,
shielded, correctly terminated, and normally restricted
to two meters in length. Wall chargers approved for
this product employ special provisions to avoid radio
interference and should not be altered or substituted.

Canada

In compliance with Industry Canada rules, the following
statement must appear on the device or in the user
documentation:

This Class B digital apparatus complies with
Canadian ICES-003.

This device complies with Industry Canada licence-exempt

RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of the
device.

Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions

suivantes: (1) l’appareil ne doit pas produire de brouillage,
et (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.

Appendix C Warnings, Regulatory Information, Licensing 43

Radio Frequency Safety

This equipment complies with radiation exposure limits set

forth for an uncontrolled environment. This equipment is
in direct contact with the body of the user under normal
operating conditions. This transmitter must not be co­located or operating in conjunction with any other antenna
or transmitter.

Cet équipement est conforme aux limites d’exposition
aux radiations dans un environnement non contrôlé.

Cet équipement est en contact direct avec le corps
de l’utilisateur dans des conditions de fonctionnement
normales. Cet émetteur ne doit pas être co-localisées
ou opérant en conjonction avec tout autre antenne ou
transmetteur.

CE Marking (European Union)

Products bearing the CE marking comply with the

2004/108/EC (EMC Directive), 1999/5/EC (R&TTE
Directive), 2006/95/EC (Low Voltage Directive) issued by the
Commission of the European Community.

CE compliance of this device is valid only if powered
with/by a CE-marked wall charger provided by the
manufacturer. Cables connecting to the USB host port must
use a ferrite core/bead on the cable. The ferrite core must
be placed on the cable near the end that connects to the
FC-5000. This device has been evaluated using the following
standards to demonstrate compliance with applicable
directives:

 EN 60950 -1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013

 EN 62311:2008, EN 62209-2:2010
 EN 301 489-1 V1.8.1
 EN 301 489-3 V1.6.1
 EN 301 489-7 V1.3.1
 EN 301 489-17 V2.2.1
 EN 300 328 V1.8.1
 EN 301 893 V1.7.1
 EN 301 511 V9.0.2

44 FC-5000 Ruggedized Field Computer Owner’s Manual

 E N 55022:2010
 E N 55024:2010

The telecommunication functions of this device may
be used in the following EU and EFTA countries: Austria,
Belgium, Bulgaria, Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania,

Luxembourg, Malta, Netherlands, Nor way, Poland, Portugal,

Slovak Republic, Romania, Slovenia, Spain, Sweden,
Switzerland, and United Kingdom.

Restrictions apply to the operation of the radio in this
device.

France (Radio Restrictions)

Restrictions apply to the operation of the Bluetooth radio
in this device. This equipment may be used indoors. Due

to the potential that this radio may transmit in excess of 10

mW in the band 2454 to 2483.5 MHz, outdoor operation is
restricted.

Restrictions apply to the operation of the 802.11b/g radio
in this device. This equipment may be used indoors on
channels 1 to 13. Outdoor operation is permitted on
channels 1 to 8, as transmit power in the band 2454 to

2483.5 MHz is limited to 10 mW. The latest requirements may
be found at: http://www.art-telecom.fr.

Declaration of Conformity

The Declaration of Conformity for CE Marking is available
at: http://us.Topcon.com/products/software-eld-

controllers/eld-controller-hardware/FC-5000.

Licensing Information

This Product is licensed under the AVC, the VC-1 and the
MPEG-4 Part 2 Visual patent portfolio licenses for the
personal and non-commercial use of a consumer to (i)
encode video in compliance with the above standards
(“Video Standards”) and/or (ii) decode AVC, VC-1 and
MPEG-4 Part 2 Visual that was encoded by a consumer
engaged in personal and non-commercial activity or was
obtained from a video provider licensed to provide such

Appendix C Warnings, Regulatory Information, Licensing 45

video. None of the licenses extend to any other product

regardless of whether such product is included with this
product in a single article. No license is granted or will be
implied for any other use. Additional information may be
obtained from MPEG LA, LLC. See www.mpegla.com.

No rights are given for Dolby patents used in the Dolby
portion of this product. A list of relevant patents may
be obtained from Dolby Laboratories, Inc. No rights are
granted to any Dolby copyrights, including the right to
reproduce or distribute any portions of this product that
includes Dolby intellectual property. Licenses for these
activities may be obtained from Dolby.

Any use of this product in any manner other than personal
use that complies with the MPEG-2 standard for encoding

video information for packaged media is expressly

prohibited without a license under applicable patents in
the MPEG-2 patent portfolio, which license is available from
MPEG LA, LLC, 6312 S. Fiddlers Green Circle, Suite 400E,
Greenwood Village, Colorado 80111 U.S.A.

Windows 10 is automatically updated, which is always
enabled. ISP fees may apply. Additional requirements may
apply over time for updates.

Cortana experience may vary by device.

46 FC-5000 Ruggedized Field Computer Owner’s Manual

D

Specifications

FC-5000RuggedTabletSpecications

Note: Specications are subject to change without notice.

FEATURE SPECIFICATION

Operating
System

 Microsoft
 English, French, German, Spanish,

Brazilian Portuguese are built in;
other languages are available for

download
Processor  Quad-core Intel® Atom™ Z3745

Memory  4 GB RAM (LPDDR3)

Primary Data

 64 or 128 GB ash storage

Storage
Micro SD/SDXC

 SD/SDXC slot, user accessible

Card Slot
Physical

Features

 Dimensions, standard: 5,4” wide x

8.48” long x 1.36” thick (137 mm x 215

mm x 35 mm)

 Weight: 1.5 to 2.2 lb (680-907 g)

depending on battery conguration

and internal options installed

 Durable, chemical- and shock-

resistant design

 Easy-to-grip, impact-absorbing,

overmolded bumpers
Display  Active viewing area: 7” (178 mm)

 WXGA 800 x 1280 pixel resolution
 Backlit LCD
 Outdoor viewable
 Landscape or portrait orientation

®

Windows 10 Pro

Touchscreen  Capacitive multi-touch interface for

use with gloves, small tip stylus, and in

wet conditions

 Chemically-strengthened

Dragontrail™ High Ion-Exchange

(HIE™) coverglass for impact and

scratch resistance

 Touchscreen disable function
 Touchscreen prole options

48 FC-5000 Ruggedized Field Computer Owner’s Manual

FEATURE SPECIFICATION

Keyboard  Programmable keys

 Backlit keys

Batteries  FC/SHC-5000 Rechargeable Li-Ion

Bat 3.7VDC 10600 mAh, 38.7 Whr

Topcon PN 1013591- 01

 Run time of up to 20 hours
 Charging time 4 to 6 hours
 Built-in battery intelligence
 User-replaceable
 Internal 19.3 Whr battery provides

an additional 50% of runtime and

hot-swap capability; not user

replaceable (not user accessible)
Connector Ports  USB 3.0 Host (full size A connector)

 Power input is 10 V - 18 V, nominal 12

VDC

 3.5 mm audio jack, supports stereo

headset/microphone
Wireless

Connectivity

 Bluetooth

extra long range

 Wi-Fi 802.11 a/b/g/n 2.4 GHz and 5

®

wireless technology 4.0,

GHz
Audio  Mono speaker, loud and clear

 Microphone, low noise

LED Activity
Indicators

 Red: power applied/charging status
 Green: application programmable
 Blue: application programmable
 Amber Light: Front or rear facing

camera is in use
Standard

Sensors/
Features

 Ambient light sensor
 Compass
 Accelerometer
 Gyroscope
 TPM (Trusted Platform Module) v2.0

Appendix D Specications 49

FEATURE SPECIFICATION

Temperature

Specications

 Operating Temperature: –4° to 122° F

(–20° to 50° C).

Storage Temperature: –22° to 158° F

(–30° to 70° C)

 Battery Charging Temperature: -4° to

140° F (-20° to 60° C)
Shock

Resistance
Environmental

Ratings and
Standards

 Withstands multiple 4 foot drops to

concrete

 IP68 rating (1.4 meters for 2 hours),

waterproof and dustproof

 Designed to MIL-STD810G.

Tests:

ME-60: sand & dust

ME-51,53,& 54: X,Y,& Z-axis helicopter

vibe

ME-55, 56, & 57: X, Y, & Z -axis general

vibe

ME-52: Water Immersion, 1 meter

ME-59: Aggravated Temperature-

Humidity cycle

ME-67: Temperature cycle

ME-62: Temperature shock

ME-66: Altitude

Certications

and Standards

 FCC Class B
 CE Marking (applicable EMC, R&TTE,

and LVD directives)

 Industry Canada
 EN60950 Safety

 Bluetooth SIG qualication

 IP68 waterproof and dustproof
 Designed to MIL-STD 810G
 RoHS 2 compliant

War ranties  24 months for FC-5000

 90 days for accessories
 Extended service and maintenance

plans

50 FC-5000 Ruggedized Field Computer Owner’s Manual

FEATURE SPECIFICATION

Software
Included

 Alarms
 Calculator
 Calendar
 Contacts
 E-Mail
 File Explorer
 Help
 Internet Explorer
 Internet Sharing
 Notes
 Pictures & Videos
 Remote Desktop
 Search
 Settings
 Task Manager
 Tasks

 Software on individual units may vary

from this list.

Software on individual units may vary
from list based on the model

Congurations  Standard with Wi-Fi, Bluetooth, 4 GB

RAM, 64 or 128 GB ash storage

 Geo with Standard features plus

Front and Rear Cameras and a GNSS

Receiver and Antenna

 Geo/Cell with Geo features plus

Integrated 4G LTE Modem

US/North America and CE/EU models

Camera (Geo
models)

 Resolution: 8 MP rear, 2 MP front
 Autofocus
 Video capture
 JPEG image format
 Flash

Appendix D Specications 51

FEATURE SPECIFICATION

4G LTE Data
Modem (Geo
model option)

 Sierra Wireless AirPrime EM7355 or

EM7305 (region dependant)

 Supports micro-SIM card only. Micro-

SIM card header inside battery

compartment with card detect

feature and card retainer.

 Does not support voice calls or SMS
 Supports 3G UMTS, HSUPA, HSDPA,

HSPA, HSPA+, WCDMA, EVDO, LTE

* See more details at the end of this
chapter

GPS/GNSS (Geo
models)

 2 to 5 meter typical accuracy
 uBlox NEO-M8N GNSS receiver and

integrated antenna

 Integrated real-time SBAS receiver

(WAAS, EGNOS, etc.)

 72 GNSS tracking channels
 Optional: uBlox NEO-M8T with post-

processing data output and external

GNSS antenna connection for sub-

meter accuracy
Standard

Accessories

 FC/SHC-5000 Adjustable Hand Strap

Topcon PN 10135 89- 01

 Removable Li-Ion battery
 AC wall charger with international

plug kit

- In put: 10 0-24 0 VAC, 50/60 Hz, 0. 5 A

- Output: 12 VDC, 1.67 A

 Capacitive ne tip stylus with tether
 Quick Start Guide
 Owner’s Manual (on our website)
 Two year warranty on FC-5000

Optional
Accessories

 Internal extended battery, 3.65 V

@5300 mAh, 19.3 Whr Li-Ion

 IIntegrated RS-232 9-Pin, D-Sub

Communication

 uBlox NEO-M8T GNSS receiver and

external antenna connection

52 FC-5000 Ruggedized Field Computer Owner’s Manual

FEATURE SPECIFICATION

Optional
Accessories

 FC/SHC5000 Docking Station,

includes power/charge input, HDMI

output, 2 USB 2.0 (full size A), Ethernet

Topcon PN 1013592-01

 FC/SHC-5000 Travel Charger Topcon

PN 1013593 - 01

 FC/SHC-5000 Adj Shoulder Strap

Topcon PN 10145 8 8-01

 FC/SHC-5000 Ultra-Clear Screen

Protector Topcon PN 1013584-01

 FC/SHC-5000 Anti-Glare Screen

Protector Topcon PN 1013586-01

 FC/SHC-5000 Polarized Screen

Protector Topcon PN 1013587-01

 Ofce 365 Survey/GPS pole clamp

and mount

 Vehicle charger cable, 12 V vehicle

power port, 6 ft.

 Vehicle mounting dock with power

and communications.

 Vehicle Dock/Pole mount - dock

attachment

 Serial cable
 Holster carrying case
 Flip cover tted case
 4-point harness
 SD cards in various sizes

*4GLTEDataModem-AdditionalInformation

Mode Model/Region Frequency Bands
LTE North America B2, B4, B5, B13, B17, B25
EU/ROW B1, B3, B7, B8, B20
UMTS/HSPA+ North America B1, B2, B4, B5, B8
EU/ROW B1, B2, B5, B8
GSM/GPRS/EDGE North America GSM 850, EGSM 900,

DCS 1800, PCS 1900
EU/ROW GSM 850, EGSM 900,

DCS 1800, PCS 1900

CDMA 1xRT T/ North America BC0, BC1, BC10

EV-DO Rev A

Note: ROW = Rest of World, or Non- North America

Appendix D Specications 53

54 FC-5000 Ruggedized Field Computer Owner’s Manual

Index

Index

Symbols

4G Data Modem

Data Account, Set up With Wireless Provider 25
Maintenance of Your Modem 27
RF Interference Issues 27
Set up the Cell Modem 27
SIM Card Installation 25

A

Accessories

Optional 53

Standard 52
AC Charger 5, 14 , 41
Action Center 10
Anatomy of the FC-5000 2–3
Audio Features 18

Audio Jack 18

Microphone 18

Speaker 18

B

Battery Compartment 3
Battery Door 2–3
Battery Pack

Battery Life 14, 15

Charge 5, 14

Install 4 –5

Internal 2, 14 –15

Removable 3, 4, 13 –15

Specications

Status 14

Storage 30

Warnings 40
Battery Pack, Internal 14 –15
Battery Pack, Removable 3 –5, 14 –16
Bluetooth Wireless Communication 21–22

56 FC-5000 Ruggedized Field Computer Owner’s Manual

C

Camera 25

Audio 25

Specications 51
Care and Maintenance

Cleaning 31

Storage 30
Cautions 17, 26, 31, 38
Certications and Standards 42

Canada 43

CE Marking, European Union 44

Licensing Information 45

Radio Frequency Safety 44

United States 42
Cleaning 31
Compass 21
Congurations 51
Connector Ports 3, 18
Ctrl-Alt-Delete Function 20

D

Data Modem 25

Set up a Data Account 25

Install the SIM Card 26
Data Storage 48
Declaration of Conformity 45
Display

Backlight 11
Magnier 11

Documentation 3

E

Environmental Ratings and Standards 50
Equipment Warnings 41
Excell Battery Company Charge Instructions 41

F

Features

Optional 24
Standard 10

Index 57

G

Geo Model 24, 25
GPS/GNSS 24, 52

H

Hand Strap 6
Hibernate 19

K

Keypad

Backlight Brightness 13
Key Functions 12–13
Programmable Keys 13

L

Language Installs 8
LED Activity Indicators 16
Light Sensor 16
Limitation of Liability 36
Locked Up 20

M

Magnier 11
Memory 48
Microphone 18, 49

O

Operating System 10, 48

Install Languages 8
Updates 8

P

Physical Features 48
Powering Off and On 19
Power Management

Battery Pack 14

Charging Battery Packs 16
Power Off 19
Product Warnings 40

58 FC-5000 Ruggedized Field Computer Owner’s Manual

R

Recovery Image 21
Recycling the FC-5000 and Batteries 31
Removable Battery Pack 3–5
Repairing 38

System Information 38
Repairs, Upgrades, and Evaluations 38
Reset 20
Restore 21
RS-232C Port 49

S

Screen Protector 53
SD Cards 17
Sensors 21

Accelerometer 21

Compass 21

Gyroscope 21
Service Plans 37
Set Up 6
Set up Tasks, Initial 3
SIM Card 3, 4, 26
Sleep 18
Software Included 51
Speaker 2
Specications 48–55
Start Menu 10
Storing the Mesa 2 30
Stylus 3, 6, 18

Stylus Storage Slot 2

Tether 6
System Information 10, 38

T

Tablet mode 6
Task Manager 20
Temperature Specications 50
Touchscreen 10 –12

Calibration Tool 12

Protecting the Touchscreen 31

Settings 10

Specications 48

Index 59

U

Updates, Operating System and Documentation 8
USB Host 18

W

Wall Charger 5, 14
Warnings 40–41

Battery Warnings 40–41

Wall Charger Warnings 41
War ranty 34–37

Exclusions 34

Limitation of Liability 36

Remedy 35

Repairs 36

Services 37

Warranty Exclusions 34
Wi-Fi Wireless Communication 22

Connecting to a Wi-Fi Network 22
Windows Start Menu 10
Wireless Safety 27

60 FC-5000 Ruggedized Field Computer Owner’s Manual