Instruction manual
Electric Storage |
|
|
|
Water Heater |
|
|
|
/ Models
|
SWH RE3 50 V |
SWH RE3 30 V SL |
|
SWH RE3 80 V |
SWH RE3 50 V SL |
|
SWH RE3 100 V |
SWH RE3 80 V SL |
|
SWH RE4 30 VH |
|
|
SWH RE4 50 VH |
|
|
SWH RE4 80 VH |
|
RE4 |
SWH RE4 100 VH |
|
RE3 |
|
|
|
|
. |
|
Outlook of devices, aslo colour scores can be revised without any special advance notices. |
|
TABLE OF CONTENTS |
|
|||
1. |
Important information..................................................................................... |
2 |
||
2. |
Precautions.................................................................................................... |
|
2 |
|
3. |
Performance parameters............................................................................. |
3 |
||
|
Technical characteristics............................................................... |
4 |
||
|
Dimensions............................................................................................ |
|
5 |
|
4. |
Water |
heater |
description....................................................................... |
5 |
5. |
Scope |
of delivery......................................................................................... |
5 |
|
6. |
Water |
heater |
installation...................................................................... |
6 |
|
Location.................................................................................................. |
|
6 |
|
|
Water |
heater |
mounting methods.......................................................... |
6 |
|
Water |
heater |
mounting............................ ................................................. |
7 |
|
Connection to water main........................................................................... |
7 |
||
|
Connection to electric main....................................................................... |
8 |
||
7. Water |
heater |
operation.............................................................. |
9 |
|
8. Maintenance............................................................................................ |
|
10 |
||
9. Troubleshooting............................................................................. |
11 |
|||
10. Wiring |
diagram...................................................................... |
11 |
||
11. Disposal..................................................................................................... |
|
12 |
||
Dear Customer!
Thank you for your good choice. You purchased TIMBERK electric storage water heater with an enameled internal tank. It will serve you for a long time!
TIMBERK electric storage water heaters will provide a lot of hot water and will automatically maintain the specified temperature. They are perfect to provide hot water for country houses, cottages, baths and other standalone amenity rooms.
1.IMPORTANTINFORMATION
Please, read this operation manual carefully prior to operating the water heater. This operation manual contains important information regarding your safety, as well as recommendations on proper operation of the appliance and its maintenance.
Keep this operation manual together with a guarantee slip, a sales check, and, if possible, carton box and packaging material.
Different types of this device are described in this manual.
The water heater that you have bought can slightly differ from the one, described in the manual, but that doesn't affect its operating procedures.
IMPORTANT PRECAUTIONS AND INSTRUCTIONS, CONTAINED IN THIS MANUAL, DO NOT ACCOUNT FOR ALL POSSIBLE MODES AND SITUATIONS TO BE ENCOUNTERED. IT IS VITAL TO UNDERSTAND THAT COMMON SENSE, CAUTION AND THOROUGHNESS ARE THE FACTORS THAT ARE IMPOSSIBLE TO BE BUILT-IN IN ANY PRODUCT. THESE FACTORS MUST BE TAKEN INTO CONSIDERATION BY A PERSON, INTERESTED IN PROPER OPERATION OF THE UNIT. THE MANUFACTURER DOES NOT BEAR ANY RESPONSIBILITY IN CASE WHEN THE UNIT OR ITS PARTS ARE DAMAGED DURING TRANSPORTATION, AS A RESULT OF IMPROPER INSTALLATION, VOLTAGE FLUCTUATIONS, AS WELL AS IF SOME PART OF THE UNITWAS ALTERED OR MODIFIED.
2.PRECAUTIONS
A number of precautions is to be observed upon operation of the water heater. Improper operation as a result of ignoring precautions may harm health of the user and other people, as well as damage their property.
1.Any electrical appliance must be supervised when in operation, especially if there are children nearby. Make sure children do not touch the appliance.
2.Prior to installing the water heater, not connecting it to electrical main, check and make sure the outlet for the water heater has a ground pin and if it is properly earthed. If there is no earth circuit in your electrical main then operation of the water heater is dangerous for your life.
3.Connect the water heater only to 220V, 50Hz main. If necessary, find out parameters of your mains at power suppliers.
4.To prevent overheating and risk of fire, as well as damage of internal electrical main, do no modify the power cord's length and do no connect the water heater through electrical extenders.
5.It is forbidden to switch on the water heater if it is not filled with water or if water cannot go through a pressure safety valve.
2 www.timberk.com electric storage water heater
6.Never use the water heater if it is broken.
7.Do not remove the water heater cover when it is in operation.
8.Immediately unplug the water heater from electrical main if strange sounds, odor or smoke are coming from it.
9.Always unplug the water heater from electrical main during a thunderstorm.
10.Prior to cleaning and maintenance of the water heater unplug it from electrical main. Cleaning and maintenance must be performed in compliance with instructions of this operation manual.
11.Do not use hazardous chemical substances to clean the water heater and prevent their contact with the appliance.
12.To prevent electrical shock the damaged power cord must be replaced only in manufacturer's authorized service centers by qualified specialists.
13.To prevent electrical shock do not place the power cord nearby heating devices and flammables or combustibles.
14.Since temperature of water in the water heater can reach 75°C, when it is in operation you should not place your body parts under hot water at the first run. To prevent burns you should adjust the temperature of the discharging water.
15.Do not use the water heater for purposes not specified by this operation manual.
16.Do not use the water heater in an explosive or corrosive environment. Do not store gas and other volatile flammable liquids next to the appliance
it is very dangerous!
17.It is forbidden to make alterations in the design of the water heater or modify it.
18.Any service operations must be performed by a specialized organisation and qualified specialists. Improper installation may cause voiding of guarantee maintenance.
19.The water heater is not intended for use by children and persons with reduced physical, sensory or mental capabilities, or a lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by an individual responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
ENGLISH
3. PERFORMANCE PARAMETERS
1.Completely automatic control: automatic water heating, continuous automatic water temperature control.
2.DROP Defense leakage protection and protection against surplus pressure within a tank (pressure safety valve).
HOT Defense two-stage overheating protection (thermostat and temperature limiter).
ALL PROTECTION SYSTEMS ARE RELIABLE AND SAFE.
3.Steel internal tank with a special titanium fine glass enamel coating, applied by the modern electrostatic dry enameling method, is resistant to corrosion and scale. Also enamel has an increased adhesive capability and high ductility (hardened at 850°C), which allows it to expand and contract at temperature drops in the same ratio as the internal tank walls not generating microcracks, where corrosion may emerge.
4.Pipes of heating elements are designed taking into account high heat load: safe and reliable, with an increased service life.
5.The water heater is equipped with an anode bar to protect the internal tank from corrosion and decrease scale generation on the heating element.
6.Internal thickened urethane foam insulation allows to efficiently preserve temperature of the heated water and minimize heat losses, reducing power consumption of the water heater.
7.The water heater has simple structure and is convenient in service.
www.timberk.com electric storage water heater |
3 |
Technical characteristics
Technical characteristics of water heaters are given below in Table 1, 2.
Table 1
|
|
|
|
|
|
|
Product item |
|
|
|
|
|
Description |
Units |
SWH RE3 50 V |
SWH RE3 80 V |
SWH RE3 100 V |
SWH RE3 30V SL |
SWH RE3 50V SL |
SWH RE3 80V SL |
|
|
|
Rated voltage |
V/Hz |
~220/50 |
~220/50 |
~220/50 |
~220/50 |
~220/50 |
~220/50 |
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
Rated current |
|
9,1 |
9,1 |
9,1 |
9,1 |
9,1 |
9,1 |
|
|
|
Rated power |
W |
2000 |
2000 |
2000 |
2000 |
2000 |
2000 |
|
|
|
consumption |
|
|
|
|
|
|
|
|
|
|
Tank capacity |
l |
50 |
80 |
100 |
30 |
50 |
80 |
|
|
|
Rated pressure |
MPa |
0,75 |
0,75 |
0,75 |
0,75 |
0,75 |
0,75 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Protection class |
- |
IP 4 |
IP 4 |
IP 4 |
IP 4 |
IP 4 |
IP 4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Electrical |
|
I |
I |
I |
I |
I |
I |
|
|
|
protection class |
|
|
||||||
|
|
Heating time, at |
min |
40 |
68 |
80 |
25 |
40 |
68 |
|
|
|
30 ºC |
|
|||||||
|
|
Appliance |
mm |
390x645x390 |
440x775x440 |
440x925x440 |
355x515x355 |
355x745x355 |
390x925x390 |
|
|
|
dimensions |
|
|||||||
|
|
(W x H x D) |
|
|
|
|
|
|
|
|
|
|
Weight |
kg |
15,1 |
22,0 |
26,0 |
11,5 |
16,3 |
23,3 |
|
|
|
Factual year |
kW h |
405,15 |
525,6 |
631,45 |
357,7 |
401,5 |
518,3 |
|
|
|
energy consumption |
|
|||||||
|
|
Constant daily loss |
kW h/day |
1,15 |
1,49 |
1,76 |
1 |
1,13 |
1,44 |
|
Table 2
|
|
|
|
|
Product item |
|
|
Description |
Units |
SWH RE4 30 VH |
SWH RE4 50 VH |
SWH RE4 80 VH |
SWH RE4 100 VH |
|
Rated voltage |
V/Hz |
~220/50 |
~220/50 |
~220/50 |
~220/50 |
|
Rated current |
|
9,1 |
9,1 |
9,1 |
9,1 |
|
Rated power |
|
2000 |
2000 |
2000 |
2000 |
|
consumption |
W |
||||
|
Tank capacity |
l |
30 |
50 |
80 |
100 |
|
Rated pressure |
MPa |
0,75 |
0,75 |
0,75 |
0,75 |
|
|
|||||
|
Protection class |
- |
IP 4 |
IP 4 |
IP 4 |
IP 4 |
|
Electrical |
|
I |
I |
I |
I |
|
protection class |
|
||||
|
Heating time, |
min |
25 |
40 |
68 |
80 |
|
at 30 ºC |
|||||
|
Appliance |
|
355x515x355 |
390x645x390 |
440x775x440 |
440x925x440 |
|
dimensions |
mm |
||||
|
(W x H x D) |
|
|
|
|
|
|
Weight |
kg |
11,5 |
15,1 |
22,0 |
26,0 |
|
Factual year |
kW h |
339,45 |
357,7 |
514,65 |
631,45 |
|
energy consumption |
|
||||
|
Constant daily loss |
kW h/day |
0,96 |
1,14 |
1,46 |
1,77 |
4 www.timberk.com electric storage water heater
Dimensions |
|
|
|
G |
|
|
|
|
|
|
|
D |
|
|
F |
|
C |
|
E |
|
|
|
||
A |
Fig. 1 |
B |
Fig. 2 |
Fig. 3 |
Dimensions of water heaters (mm) are made in accordance with fig. 1, fig. 2 and fig. 3.
Table 3
Model name |
Capacity, l |
A |
B |
C |
D |
E |
F |
G |
SWH RE3 30 V SL/ RE4 30 V |
30 |
100 |
95 |
200 |
160 |
84 |
450 |
Ø355 |
SWH RE3 50 V SL |
50 |
100 |
95 |
300 |
186 |
84 |
680 |
Ø355 |
SWH RE3 50 V/RE4 50 V |
50 |
100 |
112 |
250 |
160 |
84 |
580 |
Ø390 |
SWH RE3 80V SL |
80 |
100 |
112 |
450 |
176 |
84 |
860 |
Ø390 |
SWH RE3 80 V/RE4 80 V |
80 |
100 |
137 |
300 |
173 |
84 |
710 |
Ø440 |
SWH RE3 100 V/RE4 100 V |
100 |
100 |
137 |
450 |
173 |
84 |
860 |
Ø440 |
4. WATER HEATER DESCRIPTION |
3 |
|
RE3 V, RE3 |
V SL |
2 |
|
||
|
1 |
4 |
|
10 |
|
|
9 |
|
|
8 |
|
|
7 |
|
Fig. 4
6 |
5 |
ENGLISH
1.Internal tank
2.External case
3.Thermometer
4.Power cable
5.Hot water inlet nozzle
6.Hot water outlet nozzle
7.Control panel
8.Heating element
9.Protective magnesium anode
10.Heat insulation
RE 4...V
10 |
9 |
7 |
6 |
5
4
Fig. 5
1 |
2 |
8 |
3 |
1.Body of water heater
2.Internal tank
3.Control panel
4.Hot water outlet pipe
5.Power cord
6.Inlet pipe
7.Heat insulation
8.Heating element
9.Protective magnesium anode
10.Thermometer
5. SCOPE OF DELIVERY
1. Water heater 1 pc.
2. Anchor bolt 2 pcs.
3. Pressure safety valve 1 pc.
4. Operation manual 1 pc.
5. Guarantee slip 1 pc.
6. Package 1 pc.
www.timberk.com electric storage water heater |
5 |
6. WATER HEATER INSTALLATION
Location
1.Electric water heater should be mounted on a firm wall.
2.The wall, where the electric water heater is to be mounted, must withstand at least the double weight of the water heater, fully filled with water; there must be no cracks and other damages on the wall. Otherwise it is necessary to take measures to strengthen the mounting or mount the water heater on a special support.
3.If a bathroom is too small, the water heater can be installed elsewhere, unexposed to direct sunlight and unavailable for moisture. However, to reduce heat losses in pipelines, the location, where a water heater is to be installed, must be as close to the place, where hot water is used, as possible.
Water heater mounting methods
Fig. 6 shows the way to mount the water heater for one consumption point (for SWH RE3 ... V).
Vertical installation
|
|
10 |
|
|
2 |
|
9 |
|
|
|
8 |
|
||
|
|
|
||
3 |
|
7 |
|
|
4 |
6 |
11 |
12 |
|
5 |
||||
13 |
|
Fig. 6 |
||
|
|
|||
*Does not included in the scope of delivery |
|
|
|
1.Power cord with a plug
2.Magnesium anode water discharge nozzle 3.Water outlet
4.Hot water supply adjustment tap* 5.Mixer*
6.Shower header*
7.Cold water supply adjustment tap* 8.Pressure relieving opening 9.Check relief valve
10.Water inlet 11.Water heater
12.Water main shut-off valve* 13.Water main
14.T-bend*
IMPORTANT!
You can use the same way of installation for SWH RE4 ... VH series. But, please, note that pipe of cold water (9) is on the left position. Pipe of hot water (2) is on the right.
Water heater mounting methods
Fig. 7 shows the way to mount the water heater for several consumption points (for SWH RE3 ... V).
Vertical installation
Fig. 7
6 www.timberk.com electric storage water heater
1.Power cord with a plug 2.Water heater
3.Check relief valve 4.Cold water supply valve* 5.Mixer*
6.Shower header*
7.Water main shut-off valve* 8.Pressure relieving opening 9.Water main
10.Bath tub* 11.T-bend* 12.Water outlet 13.Water inlet
NOTE:
If you install water heater of SWH RE4 ... VH series as vertical direction, please mind the pipe of hot water is on the right.
Water heater mounting
NOTE:
Please, use accessories, provided by the manufacturer, to install the water heater. Electric water heater must not be mounted on a wall prior you make sure that the bracket is installed firmly and securely. Otherwise the electric water heater may fall down from the wall, which may cause its damage and even serious accidents involving bodily injury. When determining points for bolt holes, it is necessary to provision some spare space between the lower part of the water heater and the floor not less than 0.6 m, and when installing RE4 VH appliance horizontally there also must be some spare space between the side cover on the right side and a wall to make it convenient to perform maintenance if necessary.
ENGLISH
Fig. 8
1.The electric water heater must be mounted on a solid wall. If wall strength doesn't allow to bear the double weight of the total water heater weight fully filled with water, then it should be mounted on a special support.
2.After you chose the proper place to install the water heater, determine points for holes for anchor hook bolts (to be determined in accordance with the data sheet for the appliance you chose). Drill two holes of the corresponding depth in the wall using a drill, dimensionally fit for anchor bolts, enclosed with the water heater.
Then insert bolts into the drilled holes, and, turning bolt hooks clockwise, securely tighten bolt nuts, then hang the water heater on these anchor bolt hooks (see Fig. 8).
3.Fix a power outlet to the wall. Requirements to the outlet are as follows: 220V/10A, single-phase, three-wired. It is recommended to place the outlet on the right side above the water heater.
NOTE:
In places or on the wall, where water may get to, the power outlet installation height must be not less than 1.8 m.
Connection to water main
1. The heater must be connected to water main with at least 0.1 MPa pressure; maximum pressure is 0.75 MPa.
www.timberk.com electric storage water heater |
7 |
NOTE:
The water heater is an appliance, operating in such a manner that pressure of water in the water heater corresponds to the pressure of water in water main. If pressure in the main exceeds 0.75 MPa, then it is necessary to mount a pressure reducer before the water heater so that pressure doesn't exceed 0.75 MPa.
2.G1/2 diameter pipes are used to connect the water heater to the water pipeline.
3.To prevent a leakage when connecting pipes, use rubber sealing gaskets on the threaded pipe ends.
4.Screw a relief valve to the inlet nozzle, marked blue and embossed arrow of the water flow direction, so that the water flow direction coincides with direction of the arrow on the valve's case.
NOTE:
Do not mount additional accessories, such as a shut-off valve, between the relief valve and the inlet nozzle.
5. Water heater with the mounted valve must be connected to the water
main install a shut-off valve at the water inlet point.You need to connect a
drain pipe to the opening of the pressure relief of safety valve. Next you
should put a drain pipe to the sewer.
6.Connect the desired number of consumption points to the outlet nozzle, marked red.
7.Open the shut-off tap and one of the tap assemblies. After the tank is filled with water, as evidenced by issue of water from the cock assembly, shut the cock assembly and check the leak integrity of all joints.
IMPORTANT!
If water in the installation location contains a large amount of calcium, manganese or iron salts, then IT IS NECESSARY to mount a respective filter in the delivery system to reduce the amount of scale generated in the tank and on the heating element.
Connection to electric main
IMPORTANT!
Prior to connecting the storage water heater, make sure that the water heater is properly grounded. Proper grounding is important to minimize electric shocks and risk of fire. The power cord is equipped with a plug with a grounding pin. The appliance must be used with a properly grounded power outlet. If the outlet, you are intending to use, is not properly grounded or grounded by a time-delay fuse or a circuit breaker, contact a qualified electrician to install a proper outlet.
1.The water heater is designed to be connected to 220V single-phase electric main. Prior to connecting make sure that parameters of the electric main in the place of connection correspond to parameters, specified on the identification plate with technical parameters of the appliance. You should follow the current electrical safety code when installing the water heater.
2.The power outlet must be properly grounded. The outlet must be designed for rated current not less than 10A, electric cable with copper core must have cross section not less than 3x1.5 mm2 (for copper).
The power outlet and plug must always be dry to prevent current leakage. Regularly check if the power plug is tightly connected to the outlet. Do it in the following order: insert the power plug into the outlet, switch off the water heater after half-hour operation and unplug the cord, check if the plug is heated by your hand. If the plug is heated over 50°C, then to prevent damages, accidents and fire as a result of bad electrical contact, replace the outlet with a new one. A specialist must do this.
8 www.timberk.com electric storage water heater
IMPORTANT!
To provide reliable operation and safe use of the water heater, prior to the first run check if it is properly connected to the 220V AC mains. The water heater to be connected must be securely linked with the earth circuit of your electric mains. The waterheater must be grounded properly, otherwise it is extremly dangerous for life safety.
7. WATER HEATER OPERATION
1. At first, open one of the separable taps at the water heater outlet, then open the inlet tap. The electric water heater will start filling with water. When water flows from separable tap freely, it means the water heater is fully filled with water and you can close the separable tap.
NOTE:
During normal operation the cold water supply valve must be opened.
2. Plug the power cord into the outlet
ENGLISH
IMPORTANT!
The outlet must be designed for rated current not less than 10A, electric cable with copper core must have cross section not less than 3x1.5 mm2 (for copper).
3.Turn the thermostate handle (fig. 4,5) clockwise and set the desirable temperature. The temperature can be set from +35°C (±5° ) (MIN" position of the thermostat knob) up to 70°C (±5° ) (rightmost "MAX" position of the thermostat knob).To reduce the water temperature turn the handle anticlockwise.
4.Water temperature keeps up by the thermostate automatically.
When water temperature reach the set level, Heating is automatically switched off. At that, the indicator lamp in the lower part of the appliance extinguishes. When the temperature wil be lower then set, the heating will automaticlly start again and the indicator lamp lights up.
5.To turn off the waterheater, turn the handle to the closest left position «
» and unplug the power cord or disconnect the appliance from the power supply.
ATTENTION!
Water can start to drip from the opening of safety valve then heating process is going. It s impossible to avoid leakage of water and you can t prevent this! Locking of valve may cause rupture of the inner tank in case of failure.
IMPORTANT!
Optimum position on the control panel corresponds to the optimum water heating temperature of 58 +/-2°C, at which:
1.The user is less likely to get burned in case when the outlet water temperature is incorrectly adjusted.
2.A sufficient amount of hot water is obtained after mixing with cold water, at a lesser power energy consumption.
3.Less scale is generated on the heating element and internal surfaces of the water heater.
www.timberk.com electric storage water heater |
9 |
Loading...