Teac TE-AV300 Installation & Connection Manual
CAR DVD/CD/MP3 PLAYER
/RADIO RECEIVER
MODEL: TE-AV300
INSTALLATION CONNECTION MANUAL
1
Copyright Information
©2009 All rights reserved. This document may not in whole or in part be reproduced,
stored in a retrieval system, transmitted in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, or reduced to any electronic medium
or machine-readable form without prior consent, in writing, from [COMPANY].
[PRODUCT] and [BRAND] are registered trademarks of [COMPANY]. The logo’s,
standards, software, and/or product names mentioned herein are manufacturer and
publisher trademarks and are used only for the purpose of identification.
Disclaimer
The publishers and author assume no responsibility whatsoever for the uses made of this
material or for decisions based on its use. Further, [COMPANY] makes no warranties,
either expressed or implied, regarding the contents of this product, its completeness,
accuracy, merchantability, or fitness for any particular purpose. Neither the publisher nor
anyone else who has been involved with the creating, production, or delivery of the
material shall be liable for any reason. [COMPANY] may make improvements and/or
changes in the products and/or options described in this document at any time and
without notice.
All brand and product names used throughout this document are trademarks or
registered trademarks of their respective companies. The brand and product names are
used in editorial fashion only and for the benefit of such companies. No such use, or the
use of any trade name, is intended to convey endorsement or other affiliation with the
document.
Product specifications are subject to change without prior notice
www.[WEBSITE]
WEEE (Waste Electrical and Electronic Equipment Directive)
If at any time in the future you should need to dispose of this product
please note that: Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice.
Disposing of the battery / batteries
Please check local regulations for disposal of batteries or call your local city office or your
household waste disposal service or the shop where you purchased the product.
The battery / batteries should never be placed in municipal waste. Use a battery disposal
facility in your neighborhood or community, if available.
2
Dear Customer,
Thank you for selecting our product. In order for you to utilize this device and all its
options, we recommend that you read the corresponding instructions in this manual
before the initial use of the device, even if you’re familiar with handling electronic
devices. Please pay particular attention to the chapter “Important safety instructions”.
Store this manual in a safe location for future reference. The descriptions and features
in this manual only serve as general information and do not represent a guarantee. In
order to offer you a product of the highest quality, we reserve the right to make
possible improvements or changes without prior notification.
Important Safety Instructions
Please read and strictly observe the following instructions!
- Never open the case of the car radio; it does not contain any serviceable parts!
If the case is open, there is a risk of fatality due to electric shock.
- Do not give your car radio and especially the accessories to children. Never
let your children use electrical devices without supervision. Children are not
always able to recognize potential hazards. Also keep the packaging films
away from children. There is a danger of suffocation.
- The car radio and the accompanying components may not be exposed to
dripping or sprayed water. Make sure that no containers filled with liquid, such
as e.g. cups or bottles, are placed in the vicinity of the device.
- Make sure that the display is not exposed to any bumps. This could damage
the display.
- Please familiarize yourself with the different functions of your device before
you begin driving. Excessively high volumes can pose a risk for you and other
people in traffic. Therefore always select the volume at such a level that
environmental sounds (horns, sirens, etc.) can still be perceived.
- Don’t use the car radio at an excessive volume. This poses a risk to your
hearing.
- Please only perform lengthy changes of the device settings while the vehicle
is parked. Your concentration might be affected by the changes.
- Only install the device in such a manner that safe driving is assured.
- Install the device in such a manner that it doesn't impede the driver and can't
injure any of the vehicle’s occupants in the event of emergency braking.
- The TFT color monitor consists of glass and liquid crystals. Don’t put any
excessive pressure on the monitor, since otherwise it might scratch, break, or
sustain other damages. In addition, the image quality might be impaired.
- Don’t touch the monitor surface with hard objects and only clean it with a soft,
dry cloth and special TFT cleaner.
3
- Don’t use the device for a longer period while the vehicle's engine isn't running.
This could drain the vehicle battery to the degree that the car can no longer be
started. In addition, this might reduce the lifespan of the battery.
- Don’t park your vehicle in direct sunlight for extended periods, otherwise the
temperature in the car’s interior could rise to the point that the device overheats
and causes malfunctions. If possible, cool the interior of the vehicle in order to
ensure that the device will operate properly.
- Only let the device be installed by qualified vehicle technicians.
- Before the final installation of the device into a DIN insertion compartment in the
dashboard, connect the cables and test the connections.
- Only use the accessories included in the delivery. Usage of unauthorized
components can cause damages.
- If you need to drill holes or make other changes for the installation, consult a
specialized workshop in your area.
- This device is designed for a vehicle power supply of 12 V with the ground on
the car body (negative pole). Check the battery voltage before installing it into a
camping vehicle, bus, or truck.
- To avoid short circuits, the battery has to be disconnected before the
installation.
- Read the guidelines in this handbook for the connection of the power supply
and other options.
- Secure the installed cables with insulating tape, cable ties, or cable clamps. To
protect the cables from damage, use insulating tape when guiding them past
metal components. Place and secure all cables in such a manner that they are
not in the vicinity of movable parts, such as e.g. the parking brake,
gas/brake/coupling pedals, handlebars and seat tracks.
- Don’t place any cables in the vicinity of heat sources (e.g. near the heater
ventilation), since the insulation of the cables might get damaged and result in
short circuits.
- Don’t short circuit any cables. This can result in damages to the vehicle and
device.
- Never establish a power supply to other devices by removing the insulation of
the device’s power supply and connecting an additional cable. Otherwise, the
maximum power rating of the cable will be exceeded and there will be a danger
of overheating.
- If you have to replace the fuse, only use an identical one with the same rating.
- The connected speakers have to be high-performance speakers with a
minimum output of 40 W and impedance ranging from 4 to 8 ohm. If you
connect speakers with other output or impedance ratings, the speakers may
burn, smoke, or sustain other kinds of damage.
- When the device is turned on, a control signal adjoins the blue cable of the
connection A5 (ISO plug A). You can connect this to the relay of the extendable
4
vehicle antenna (max. 100mA, 12 V=). If your vehicle has a wire antenna inside
the windshield, connect the blue cable A5 (ISO plug A) to the pre-amplifier of
the antenna.
- If an external audio amplifier is connected to the device, the blue cable of
connection A5 (ISO plug A) may not be connected to the power supply of the
amplifier. Likewise, you may not connect it to the power supply of an active car
antenna. This poses a risk of short circuits and malfunctions.
- Insulate unused connection cables with insulating tape. The same applies to
unused speaker cables. Otherwise there is a risk of short circuits.
- Some external hard disks may not be supported. Hard disks that have built-in
power supply should be favored.
- Some models of USB storage devices or MP3 players may not be played.
- The quality and speed for reading JPEG photos depend on the resolution & the
compression ratio of the photos. Some JPEG photos may not be played due to
the discs quality and the formats. JPEG files cannot be displayed at 4:3 picture
size.
- Dirt or condensed moisture on the lens of the CD/DVD drive may impede and
even prevent the playback of data carriers.
- In general, the playback of self-burned data carriers is possible, but it depends
on the used software and the settings made with it, so that there may be
problems during playback in individual cases. You can receive further
information from the manufacturer of your software.
- Additional CD data carriers can be played back just like audio CDs. It’s
possible that CD-R/CD-RW data carriers can’t be played back correctly if they
are recorded by a device other than an audio CD recorder or due to the quality
or burning conditions.
- In addition, it may be the case that a data carrier (CD-R/CD-RW) recorded with
an audio CD recorder can’t be played back due to the conditional features,
irregular formats, or soiling of the data carriers.
- The information recorded on the data carrier (ID3TAG) is displayed by this
device.
- After inserting a CD-RW data carrier, it takes a little longer for the playback to
begin than with regular CD or CD-R data carriers. Also read the guidelines on
the sleeves of the CD-R/CD-RW data carriers before you insert them.
5
Table of Contents
Copyright Information ……………………………………………………...…………………1
Important Safety Instructions.........................................................................................2
Table of Contents..........................................................................................................5
Accessories...................................................................................................................6
Control Reference Guide...............................................................................................7
Removing & Attaching the Faceplate ............................................................................8
Removing.................................................................................................................8
Attaching..................................................................................................................8
Wiring Connections .......................................................................................................9
Installation in Dashboard.............................................................................................10
Disc Loading & Ejecting ..............................................................................................12
Basic Operations.........................................................................................................13
Multimedia Setup Menu...............................................................................................19
System Setup ........................................................................................................19
Language Setup.....................................................................................................20
Audio Setup ...........................................................................................................21
Video Setup ...........................................................................................................21
Digital Setup ..........................................................................................................21
SD/MMC Cards & USB Operations.............................................................................22
Factory Default Settings (“RESET“) .......................................................................23
Remote Control ...........................................................................................................24
Changing the Battery...................................................................................................25
Unit Operation with Remote Control............................................................................26
Technical Specifications..............................................................................................29
6
Accessories
Package contains the following accessories for installation and operation of the unit.
Installation Kit:
1 x Mounting Bracket
1 x Assemble Bar
1 x Screw B15x16
4 x Bolt M5
1 x Nut M5
1 x Flat Washer
1 x Spring Washer
2 x Unit Ejection Bars
1x UNIT IR-Remote Control
with one CR2025 3Volt cell
battery.
User Manual.
1x front panel protection case
Note:
Product image may vary from the actual delivery.
1x AV-IN Cable
Mounting Collar
7
Control Reference Guide
1. POWER/MUTE Button
2. MENU Button
3. BAND Button
4. VOLUME Button
5. DSP Button
6. AS/PS Button
7. IR Sensor
8. OPEN Button
9. PREVIOUS Button
10. NEXT Button
11. MODE Button
12. PLAY/PAUSE MEM Button
13. TFT LCD Display
14. AV-IN Jack
15. USB Socket
16. MEMORY Card Slot
17. EJECT Button
18. ANTI-THEFT LED
19. DISC Loading Slot
20. RESET Button (Hole)
8
Removing & Attaching the Faceplate
Removing
Open the front to min 45 degrees or to its fold down position. Gently press the right
side towards the left and gently remove the faceplate by pulling it towards you.
Attaching
Gently place the left side of the front onto the locking pin, then gently click the right
side onto the locking pin and close the front until you hear a click.
CAUTION: DO NOT insert the control panel into the right side. It can damage the
control panel. Never use force or a tight grip onto the buttons or the information
display when removing or attaching the Control Panel. The control panel can easily be
damaged by shocks. To avoid damage or potential theft remove the Control panel,
place it into the protective case and be careful not to drop it or subject it to strong
shocks. The rear connector that connects between the main unit and the control panel
is an extremely important part. Be careful not to damage it by pressing on it with
fingernails, pens, screwdrivers, etc.
9
Wiring Connections
Make sure you have good chassis ground. A good ground connection will eliminate
most electrical noise problems. A good chassis ground requires a tight connection to
the vehicle’s metal chassis. The area around the ground connection should be clean,
bare metal without rust, paint, plastic, dust, or dirt for a good electrical connection.
INCORRECT WIRING OR OPERATION WILL VOID THE WARRANTY
Caution: Do not interchange the connection of the wiring!!!
For some car models you may need to modify wiring of the supplied power cord.
Contact your authorized car dealer before installing this unit.
Remark: When you back a car, screen display switch to Rear Camera automatically.
Loading...