TANDBERG C90, D14128.02 User Manual
Software version TC1.0
NOVEMBER 2008
D14128.02—NOVEMBER 2008
TANDBERG Codec C90
System Integrator Guide
1
Codec C90
Contents
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
What’s in
this guide?
The top menu bar and the entries in the
Table of Contents are all hyperlinks, just
click on them to go to the topic.
Table of Contents
Introduction
Intellectual Propert y Rights ........................................................... 5
Trademark ..................................................................................... 5
Disclaimer .....................................................................................5
Patent Information .........................................................................5
Copyright Notice ...........................................................................5
Safety Instructions ........................................................................6
Environmental Issues ....................................................................7
Getting started
Assemble your system ..................................................................9
Using the Remote Control ........................................................... 10
Turn on the system ...................................................................... 12
Verify IP address settings ............................................................ 12
If you need to set a static IP address .......................................... 12
Add the system to the network ................................................... 13
Verify your settings ...................................................................... 13
Time zone settings ...................................................................... 13
About monitors ........................................................................... 14
The main monitor .................................................................... 14
Dual monitors .......................................................................... 14
Interfaces and sockets
The front panel ............................................................................ 16
Rear panel sockets overview ...................................................... 17
The Video Input Matrix ................................................................18
About the matrix ..................................................................... 18
Configure the video inputs ...................................................... 18
Administrator settings ............................................................. 18
API commands ....................................................................... 18
Video inputs (I) ............................................................................ 19
Component 1–2 (Y-Pr-Pb) ....................................................... 19
HD-SDI 1–4 ............................................................................. 19
Composite 5* / S-Video (YC) 5* .............................................. 19
HDMI 1–4 ................................................................................20
DVI-I 3 and 5 ...........................................................................20
Video outputs .............................................................................. 21
HDMI 1 and 3 ..........................................................................21
DVI-I 2 and 4 ...........................................................................21
Composite 5 ........................................................................... 21
Audio inputs (I ) ............................................................................22
Microphone/Line In 1–8 (XLR) ................................................ 22
HDMI In 3, 4 ............................................................................ 22
Line In 1–4 (RCA) .................................................................... 23
Audio outputs (I) .......................................................................... 24
Line Out 5–6 (XLR) ................................................................. 24
HDMI Out 1, 3 ......................................................................... 24
Line Out 1–4 (RCA) ................................................................. 25
Audio Signal Levels tables ..........................................................26
Audio hardware information table ............................................... 27
Volume control table ...................................................................27
Network connectors ................................................................... 28
Ethernet interface .................................................................... 28
COM port and Camera Control port ...........................................29
COM port ................................................................................ 29
Camera Control port ............................................................... 29
Power ......................................................................................... 30
Power socket ..........................................................................30
Power switch........................................................................... 30
Chassis grounding ..................................................................30
Other connectors ........................................................................ 31
USB ........................................................................................ 31
GPIO .......................................................................................31
T Link ......................................................................................31
About the TANDBERG API
TANDBERG API .......................................................................... 33
Basic Principles ......................................................................33
The TANDBERG API-Engine ...................................................33
Structuring of Information ...................................................33
Addressing Using XPath or TANDBERG SimplePath ..........34
Feedback ............................................................................34
Connecting to the codec ............................................................ 35
Accessing XACLI ....................................................................35
Telnet/SSH login .................................................................35
Serial port login ................................................................... 35
Serial port configurations ....................................................35
Hardware & Cabling (RS-232) ................................................. 36
Troubleshooting (RS-232) .......................................................36
Value types and formats ............................................................. 37
Root commands .........................................................................38
Main type of commands ............................................................. 39
Configuration type commands ................................................ 39
Command type commands .................................................... 39
Status type commands ........................................................... 39
Special commands .................................................................39
Feedback type command ................................................... 39
D14128.02—NOVEMBER 2008
2
Codec C90
Contents
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Preferences type command ................................................ 39
About xConfiguration ..................................................................40
xConfiguration operations ........................................................... 41
Return result parameters ........................................................ 41
xConfiguration Help ................................................................ 41
xConfiguration Read ............................................................... 41
xConfiguration Write ................................................................ 41
About xCommand ....................................................................... 42
xCommand operations ...............................................................43
Return result parameters ........................................................43
xCommand Help ..................................................................... 43
xCommand Write .................................................................... 43
About xStatus commands ..........................................................44
Query status information ......................................................... 45
About xHistory command ........................................................... 46
About xFeedback ........................................................................ 47
About xPreferences .................................................................... 48
TANDBERG XML API service ......................................................49
xConfiguration type commands
Description of the xConfiguration commands ............................. 51
The Audio settings .................................................................. 51
The Camera settings ............................................................... 53
The Conference settings ......................................................... 54
The Do not disturb setting ...................................................... 55
The H323 Profile settings ........................................................55
The Network settings ..............................................................56
The Network services settings ................................................ 57
The Phone book settings ........................................................59
The Provisioning settings ........................................................ 59
The Serial por t settings ...........................................................59
The SIP Profile settings ...........................................................60
The Standby settings .............................................................. 60
The System unit set tings ......................................................... 61
The Time zone setting ............................................................. 61
The Video settings .................................................................. 61
The Experimental menu ..........................................................63
xCommand type commands
xCommands with parameters ..................................................... 65
The Audio commands ............................................................. 65
The Boot command ................................................................67
The Call commands ................................................................67
The Call Log commands .........................................................68
The Camera commands .........................................................69
The Dial command .................................................................. 71
The DTMF Send command ..................................................... 72
The TString Send command ................................................... 72
The Far End Control commands .............................................73
The HTTP Feedback commands ............................................ 74
The Key commands ................................................................ 75
The Presentation commands ..................................................76
The Preset commands ............................................................ 77
The SString Send command ................................................... 78
The Standby commands ......................................................... 78
The Video command ............................................................... 79
The CamCtrlPip command .....................................................79
The System Unit commands ................................................... 80
The Phone book commands ................................................... 81
The Experimental menu ..........................................................85
xStatus type commands
xStatus commands ..................................................................... 89
Examples of returned status information ................................ 89
The Audio status ..................................................................... 89
The Call status ........................................................................90
The Camera status.................................................................. 91
The Conference status ............................................................ 92
The Diagnostics Call status ..................................................... 93
The H323 Gatekeeper status .................................................. 97
The HTTPFeedback status .....................................................97
The Media channels call status ............................................... 97
The Network status ................................................................. 99
The SIP status ....................................................................... 100
The System unit status.......................................................... 10 0
The Standby status ............................................................... 103
The Video status ................................................................... 103
Cameras
The PrecisionHD 1080p camera ............................................... 10 6
Connecting the camera ........................................................ 107
Best view—Face recognition ..................................................... 108
Video output formats ................................................................ 10 9
Cameras in daisy chain ..............................................................110
Appendices
Software upgrade ......................................................................112
Upload certificates .....................................................................11 3
XML files .....................................................................................114
Log files ......................................................................................11 5
NTP Time Zone expressions ......................................................116
Suppor ted RFCs in SIP ..............................................................119
Current RFCs and drafts supported in SIP ............................119
Media capabilities supported in SIP .......................................11 9
TANDBERG Remote Control TRC5 ........................................... 120
TANDBERG Remote Control TRC5 key map ............................ 121
The PrecisionHD camera ..........................................................122
Connecting the camera ........................................................ 122
CE Declaration for Codec C90 .................................................. 123
China RoHS table ..................................................................... 124
TANDBERG Codec C90 dimensions ........................................ 12 5
PrecisionHD 1080p camera dimensions ................................... 126
PrecisionHD camera dimensions .............................................. 127
Technical specifications ............................................................ 128
D14128.02—NOVEMBER 2008
3
Codec C90
Introduction
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Chapter 1
Introduction
Thank you for choosing TANDBERG !
Your TANDBERG Codec C90 has been
designed to give you many years of safe,
reliable operation.
How to read this document
You will find that some places information
has been copied from other chapters (but
adapted, when needed) to let you have all
the relevant information there and then.
This helps eliminating the need to read
through long sections before you can even
think of get ting started.
Our main objective with this user guide is
to address your goals and needs. Please
let us know how well we succeeded!
We recommend you visit the TANDBERG
web site regularly for updated versions of
the manual.
Go to: http://www.tandberg.com/docs
In this chapter...
Intellectual property rights
Trademark
Copyright
Disclaimer
Patent information
Safety instructions
Environmental issues
D14128.02—NOVEMBER 2008
4
Codec C90
Introduction
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Intellectual Property Rights
This System Integrator Guide and the Products to which it relates
contain information that is proprietary to TANDBERG and its licensors.
Information regarding the Products is found on the page entitled
License Agreements and Patent Information.
This System Integrator Guide may be reproduced in its entirety,
including all copyright and intellectual property notices, in limited
quantities in connection with the use of the Products. Except for the
limited exception set forth in the previous sentence, no par t of this
System Integrator Guide may be reproduced, stored in a retrieval
system, or transmitted, in any form, or by any means, electronically,
mechanically, by photocopying, or otherwise, without the prior written
permission of TANDBERG. Requests for such permission should be
addressed to tandberg@tandberg.com.
Tra dem ark
TANDBERG® is a registered trademark belonging to Tandberg ASA.
Other trademarks used in this document are the property of their
respective holders.
COPYRIGHT © 2008, TANDBERG
All rights reser ved.
Philip Pedersens vei 20
1366 Lysaker, Norway
Tel: +47 67 125 125 Fax: +47 67 125 234
E-mail: tandberg@tandberg.com
Disclaimer
The specifications for the Products and the information in this
document are subject to change at any time, without notice, by
TANDBERG.
Every effort has been made to supply complete and accurate
information in this System Integrator Guide, however, TANDBERG
assumes no responsibility or liability for any errors or inaccuracies that
may appear in this document.
INTELLECTUAL PROPERT Y RIGHTS
The Products that are covered by this System Integrator Guide are
protected under copyright, patent, and other intellectual property
rights of various jurisdictions. Any applicable software licenses and
any limited warranty are located in the License Information section in
this TANDBERG Codec C90 System Integrator Guide.
This Product is
COPYRIGHT © 2008, TANDBERG
All rights reser ved.
Patent Information
The products described in this manual are covered by one or more of
the following patents:
US6,584,077 US5,838,664 US5,600,646
US5,003,532 US5,768,263 US5,991,277
US7,034,860 US7,010,119 EP01953201
US6.731.334 GB1338127
Other patents pending.
Please view www.tandberg.com/tandberg_pm.jsp for an updated
list
Copyright Notice
The product that is covered by this System Integrator Guide is
protected under copyright, patent, and other intellectual property
rights of various jurisdictions. This product is Copyright © 2008,
Tandberg Telecom AS. All rights reser ved. This product includes
copyrighted software licensed from others.
A document describing the copyright notices and the terms and
conditions of use can be found at: http://www.tandberg.com/docs
Navigate to User manuals > TANDBERG Codec C90 Copyright and
License Information to download the pdf.
IMPORTANT: USE OF THIS PRODUCT IS SUBJECT IN ALL CASES
TO THE COPYRIGHT RIGHTS AND THE TERMS AND CONDITIONS
OF USE REFERRED TO ABOVE. USE OF THIS PRODUCT
CONSTITUTES AGREEMENT TO SUCH TERMS AND CONDITIONS.
D14128.02—NOVEMBER 2008
5
Codec C90
Introduction
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Safety Instructions
For your protection please read these safety
instructions completely before you connect the
equipment to the power source. Carefully observe
all warnings, precautions and instructions both on
the apparatus and in these operating instructions.
Retain this manual for future reference.
Water and Moisture
Do not operate the apparatus under or near water –
for example near a bathtub, kitchen sink, or laundry
tub, in a wet basement, near a swimming pool or in
other areas with high humidity.
Never install jacks for communication cables •
in wet locations unless the jack is specifically
designed for wet locations.
Do not touch the product with wet hands.•
Cleaning
Unplug the apparatus from communication lines,
mains power-outlet or any power source before
cleaning or polishing. Do not use liquid cleaners
or aerosol cleaners. Use a lint-free cloth lightly
moistened with water for cleaning the ex terior of
the apparatus.
Ventilation
Do not block any of the ventilation openings of the
apparatus. Never cover the slots and openings with
a cloth or other material. Never install the apparatus
near heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers)
that produce heat.
Do not place the product in direct sunlight or close
to a surface directly heated by the sun.
Lightning
Never use this apparatus, or connect/disconnect
communication cables or power cables during
lightning storms.
Dust
Do not operate the apparatus in areas with high
concentration of dust.
Vibration
Do not operate the apparatus in areas with
vibration or place it on an unstable surface.
Power Connection and Hazardous
Voltage
The product may have hazardous voltage inside.
Never attempt to open this product, or any •
peripherals connected to the product, where
this action requires a tool.
This product should always be powered from •
an earthed power outlet.
Never connect attached power supply cord to •
other products.
In case any parts of the product has visual •
damage never attempt to connect main power,
or any other power source, before consulting
service personnel
The plug connecting the power cord to the •
product/power supply serves as the main
disconnect device for this equipment. The
power cord must always be easily accessible.
Route the power cord so as to avoid it being •
walked on or pinched by items placed upon or
against it. Pay particular attention to the plugs,
receptacles and the point where the cord exits
from the apparatus.
Do not tug the power cord.•
If the provided plug does not fit into your outlet, •
consult an electrician.
Never install cables, or any peripherals, without •
first unplugging the device from its power
source.
Servicing
Do not attempt to service the apparatus •
yourself as opening or removing covers may
expose you to dangerous voltages or other
hazards, and will void the warranty. Refer all
servicing to qualified service personnel.
Unplug the apparatus from its power source •
and refer servicing to qualified personnel under
the following conditions:
If the power cord or plug is damaged or •
frayed.
If liquid has been spilled into the apparatus.•
If objects have fallen into the apparatus. •
If the apparatus has been exposed to rain •
or moisture
If the apparatus has been subjected to •
excessive shock by being dropped.
If the cabinet has been damaged.•
If the apparatus seems to be overheated. •
If the apparatus emits smoke or abnormal •
odor.
If the apparatus fails to operate in •
accordance with the operating instructions.
Accessories
Use only accessories specified by the
manufacturer, or sold with the apparatus.
Communication Lines
Do not use communication equipment to repor t a
gas leak in the vicinity of the leak.
IMPORTANT!
There should always be a distance of minimum
10 cm (0.33 ft) free space in the front of the codec.
Min. 10 cm
WARNING!
Make sure the Codec
C90 never rest on
the front panel.
D14128.02—NOVEMBER 2008
6
Codec C90
Introduction
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Environmental Issues
Thank you for buying a product which contributes
to a reduction in pollution, and thereby helps save
the environment. Our products reduce the need for
travel and transport and thereby reduce pollution.
Our products have either none or few consumable
parts ( chemicals, toner, gas, paper).
TANDBERG’s Environmental Policy
Environmental stewardship is important to
TANDBERG’s culture. As a global company with
strong corporate values, TANDBERG is committed
to following international environmental legislation
and designing technologies that help companies,
individuals and communities creatively address
environmental challenges.
TANDBERG’s environmental objectives are to:
Develop products that reduce energy •
consumption, CO2 emissions, and traf fic
congestion
Provide products and services that improve •
qualit y of life for our customers
Produce products that can be recycled or •
disposed of safely at the end of product life
Comply with all relevant environmental •
legislation.
Digital User Guides
TANDBERG is pleased to announce that we have
replaced the printed versions of our user guides
with digital versions available on the TANDBERG
web site: http://www.tandberg.com/docs. The
environmental benefits of this are significant. The
user guides can still be printed locally, whenever
needed.
European Environmental Directives
As a manufacturer of electrical and electronic
equipment TANDBERG is responsible for
compliance with the requirements in the European
Directives 2002/96/EC (WEEE - Waste Electrical
and Electronic Equipment) and 2002/95/EC
(RoHS).
The primary aim of the WEEE Directive and RoHS
Directive is to reduce the impact of disposal of
electrical and electronic equipment at end-of-life.
The WEEE Directive aims to reduce the amount
of waste electrical and electronic equipment sent
for disposal to landfill or incineration by requiring
producers to arrange for collection and recycling.
The RoHS Directive bans the use of certain heavy
metals and brominated flame retardants to reduce
the environmental impact of WEEE which is in
landfill or incinerated.
TANDBERG has implemented necessar y process
changes to comply with the European WEEE
Directive (2002/96/EC ) and the European RoHS
Directive (2002/95/EC).
Waste Handling
In order to avoid the dissemination of hazardous
substances in our environment and to diminish the
pressure on natural resources, we encourage you
to use the appropriate recycling systems in your
area. Those systems will reuse or recycle most
of the materials of your end of life equipment in a
sound way.
Information for Recyclers
As part of compliance with the European
WEEE Directive, TANDBERG provides recycling
information on request for all types of new
equipment put on the market in Europe af ter
August 13th 2005.
Please contact TANDBERG and provide the
following details for the product for which you
would like to receive recycling information:
Model number of TANDBERG product •
Your company’s name •
Contact name •
Address •
Telephone number •
E-mail. •
D14128.02—NOVEMBER 2008
TANDBERG products put on the market af ter
August 2005 are marked with a crossed-out
wheelie bin symbol that invites you to use
those take-back systems.
Please contact your local supplier, the regional
waste administration or visit our web page http://
www.tandberg.com/recycling if you need more
information on the collection and recycling system
in your area.
7
Codec C90
Getting Started
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Chapter 2
Getting started
This chapter introduces you to the codec
and gets you up and going.
This guide has been divided into several
chapters, all of which provide different
information. You can access the chapters
directly by clicking on the menu bar at the
top of this page.
In this chapter...
Assemble your system
Using the remote control
Turn on the system
Verify IP address settings
Setting a static IP address
Add the system to the network
Verify your settings
Time zone settings
About monitors
D14128.02—NOVEMBER 2008
8
Codec C90
Getting Started
!
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Assemble your system
The illustration shows you the basic setup when connecting your monitor, PC,
1
camera, microphone, loudspeakers (if applicable ), LAN and line voltage to your
codec.
OPTIONAL:
Loudspeakers
Monitor
(Audio from HDMI 1 or
Line Out 1–2)
OPTIONAL:
Dual monitor setup
Connect the second
monitor to HDMI 3
Main camera:
Video from
PrecisionHD 1080p
Video
from PC
Main camera:
Camera Control to
PrecisionHD 1080p
OPTIONAL:
Audio from PC
Microphone
LAN/
Ethernet
Mains Power
Cable
OPTIONAL:
You may connect additional
microphones
OPTIONAL:
You may connect a second camera.
(extra camera not included). Extra camera will
require separate power supply and control
cabling. Consult the documentation supplied
with the extra camera for details.
Make sure the codec has been switched off and
disconnected from the line voltage whenever
connecting or disconnecting other equipment.
D14128.02—NOVEMBER 2008
9
Codec C90
Getting Started
4
7
ghi
pqrs
6
#
abc/123
9
1
.@
5
0
8
jkl
tuv
2
abc
3
def
mno
wxyz
1
.@
2
abc
3
def
1
.@
2
abc
3
def
System Integrator Guide
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
Using the Remote Control
ARROW UP/DOWN: Use
the up and down
arrow keys to navigate in
the menu.
ARROW RIGHT: Press
the right arrow key
to expand the selected
menu item or to move
to the right in a text
field.
OK/S EL ECT: Press the OK /
Select key to confirm your
choice or selection.
The functions keys
in the upper part of
the remote control
reflects the soft keys
on screen.
... and the middle
part of the remote
control is used to
handle the video
part of the call.
... while the lower
part of the remote
control resembles
very much the
keypad of a mobile
phone
FUNCTION KEYS: Each key reflects
a soft key on screen and represents
shortcuts and advanced functions.
ARROW LEF T: Press
the left arrow key
to go one step back
in the menu or to
move to the left in a
text field.
Batteries
Make sure the remote control has
working batteries (4 x AAA batteries).
D14128.02—NOVEMBER 2008
MICROPHONE: Press the
Microphone key to toggle
the microphones on/of f.
VOLUME: Press
the + or – on the
Volume key to adjust
the codec volume.
PR ESE NTATIO N: Press the
Presentation key to show/hide
a presentation.
ZOOM : Press
the + or – on the Zoom
key to zoom the camera
in and out.
PHONE BOOK: Press
the Phone Book key to
display the local phone
book.
L AYO UT: Press the Layout
key to display the layout
menu, then select a view
in the menu.
HOME: Press the
Home key to go back
to the main menu.
10
Codec C90
Getting Started
4
7
ghi
pqrs
6
9
1
.@
5
8
jkl
tuv
2
abc
3
def
mno
wxyz
4
7
ghi
pqrs
6
#
abc/123
9
1
.@
5
0
8
jkl
tuv
2
abc
3
def
mno
wxyz
4
7
ghi
pqrs
6
#
abc/123
9
1
.@
5
0
8
jkl
tuv
2
abc
3
def
mno
wxyz
4
7
ghi
pqrs
6
#
abc/123
9
1
.@
5
0
8
jkl
tuv
2
abc
3
def
mno
wxyz
4
7
ghi
pqrs
6
#
abc/123
9
1
.@
5
0
8
jkl
tuv
2
abc
3
def
mno
wxyz
System Integrator Guide
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
Using the Remote
Control, cont...
The functions keys
in the upper part of
the remote control
reflects the soft keys
on screen.
... and the middle
part of the remote
control is used to
handle the video
part of the call.
... while the lower
part of the remote
control resembles
very much the
keypad of a mobile
phone
CALL KEY
INITIATE CALL: Select a name from the Phone book or enter the
name, number or URI and press the Call key to initiate the call.
SHORTCUT TO RECENT CALLS: Use the Call button as a
shortcut to Recent Calls when the Call menu is not visible.
END CALL, STANDBY:
Press the End Call
key to end a call, or
when idle, press and
hold the key to go into
standby mode.
CLEAR: Press the Cancel
key to remove characters
in a text field.
Waking up the system
Press any key on the remote control to wake up the system.
ALPHANUMERIC KEYPAD
Use the keypad in the same way as you would
use a cellular phone.
0-9, a-z, period (.), @, space, *:
Press a key repeatedly to toggle
between the options displayed
on each key.
abc/123 #: Press the # key to
toggle bet ween lower case
characters and numbers.
IR sensor range ( DIP switch setting)
The IR sensor has a short and long range. Open the battery cover and remove
the batteries to set the DIP switch.
Short range (1 m): Move the DIP switch down•
Long range: Move the DIP switch up.•
D14128.02—NOVEMBER 2008
Press the HOME
key to show the
menu on screen
Touch the rubber
line sensors along
the sides to wake
The DIP
switch
up the system
11
Codec C90
Getting Started
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Turn on the system
1 3
Turn on the codec and wait a few minutes for the system to start•
Make sure the remote control has the batteries installed.•
Press • Home ( ) on the remote control to show the menu on screen
When you can see the menu on screen, proceed to Step 2.•
Show the menu:
Press • Home ( ) on the remote control to show the menu on screen
Navigate in the menu:
Use the arrow keys on the remote control to navigate up and down in •
the menus
Confirm your choice:
To confirm your choice, press • OK ( ) on the remote control
Verify IP address settings
2
Go to System Information to verif y the IP address:
Navigate to Settings > System Information1.
If you need to set a static IP address
Go to IP Settings to set static IP addresses:
Navigate to Settings > Administrator Settings > IP Settings. 1.
Set IP Assignment to Static. Press the lef t arrow key to go back one step2.
Enter the IP Address, Subnet Mask and Gateway address in the address fields. 3.
The sequence is shown below.
Press 4. OK to save the changes, or Cancel to leave without saving.
Press 5. Home ( ) to exit.
D14128.02—NOVEMBER 2008
When the IP address is automatically assigned from a DHCP ser ver, the 2.
Address of the codec is shown on the System Information page.
Press 3. Home ( ) to exit.
12
Codec C90
Getting Started
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Add the system to the network
4 5
Your service provider should have provided you with the information you
need to get on-line.
For H323 type of communication, this will include such things as system
name, H323 alias, gatekeeper address, etc. For SIP type of communication,
similar type of information will be supplied.
For networks administrated through TMS (TANDBERG Management Suite),
your TMS administrator will be able to assist you when configuring.
The H323 and SIP settings are configured from the Administrator Set tings
menu:
Navigate to Settings > Administrator Set tings > Advanced Settings.
Expand the items in need of modification and enter the information •
supplied by your service provider.
6
Verify your settings
We strongly recommend that you verify the settings by inspecting the System
Information list.
You do this by accessing the System Information in the same way as you did
when you verified you IP address setting.
Go to System Information to verif y the settings:
Navigate to 1. Settings > System Information
Verify the previous configurations. For example, if you successfully registered 2.
to a SIP server the Status will show Registered. If the registration failed the
Status will show Not registered.
Press Home ( 3. ) to exit.
Time zone settings
Verify the date and time to see if the time zone settings need to be adjusted. The
date and time is located in the upper right corner on screen.
Go to Time settings to set the NTP (date and time) settings:
Navigate to 1. Settings > Administrator Settings > Time > Zone
D14128.02—NOVEMBER 2008
You may need to consult the NTP Time Zone expression list to find the 2.
exact expression. Go to the Appendices section and the NTP Time Zone
expressions to see a complete overview.
Enter the time zone expression for where the system is located. The default 3.
value is Etc/ UTC.
NOTE: Spelling correctly is important when entering the NTP Time Zone
expression
Press 4. Save to save the changes, or Cancel to leave without saving.
Press 5. Home ( ) to exit.
13
Codec C90
Getting Started
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
About monitors
The main monitor
The main monitor can be connected to the default video output HDMI
1 or one of the other outputs which are HDMI 3, DVI-I 2 or DVI-I 4.
When connecting to HDMI 1
When you connect the main monitor to the default video output on
Codec C90 the menu, icons and other information on screen (OSD on screen display) will show on this monitor.
When connecting to DVI-I 2, DVI-I 4, HDMI 3
When connecting the main monitor to another video output, and no
menu shows on screen, you must run a shortcut on the remote control
to reset the resolution and move the OSD to this output.
The resolution will be set to the default value, which is
1280x720@60Hz for HDMI and 1024x768@ 60Hz for DVI.
The menu on screen, icons and other information (OSD - on screen
display) will be moved to the selected output.
Key sequence
If connected to DVI-I 2, DVI-I 4 or HDMI 3 you must run the following
shortcut or key sequence on the remote control.
Disconnect * # * # 0• x # (where x is output 2, 3 or 4)
Example: Set DVI-I 2 as the OSD output:
Disconnect * # * # 0 2 #•
The video outputs at Codec C90
DVI-I 4
HDMI 3
(the default connector
for the dual monitor)
DVI-I 2
HDMI 1
(the default connector
for the main monitor)
Dual monitors
When you want to run a dual monitor setup, connect the second
monitor to video output HDMI 3 on Codec C90.
Dual monitor configuration
You can also set the resolution and the OSD output by setting up a
serial port connection and run API commands. See the Codec C90
System Integrator Guide for information about API commands.
D14128.02—NOVEMBER 2008
Go to Administrator settings to set the monitor to dual:
Navigate to Settings > Administrator Settings > Video > Output > 1.
Monitor
Set the 2. Monitor to Dual.
Press 3. Home ( ) to exit.
14
Codec C90
Interfaces
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Chapter 3
Interfaces and sockets
In this chapter you will find an in-depth
presentation of the rear panel sockets and
interface of the TANDBERG Codec C90,
including audio signal levels and formats
supported.
In this chapter...
The front panel
Rear panel overview
The video input matrix
Video inputs
Video outputs
Audio inputs
Audio outputs
Audio signal level tables
Audio hardware information
Volume control table
Network connectors
COM ports
Camera control port
Power
Other connectors
D14128.02—NOVEMBER 2008
15
Codec C90
Interfaces
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
The front panel
There are four LED’s in the front of the Codec:
Power• – The POWER LED turns ON when power is connected,
otherwise OFF
Call• – The CALL LED turns ON when there are active calls on the
codec, otherwise OFF
Infrared• – The IR LED flashes when infrared signals are received
Alarm• – The ALARM LED turns ON when there is no connection to
the network, otherwise OFF
D14128.02—NOVEMBER 2008
Power Call IR Alarm
(infrared)
16
Codec C90
Interfaces
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Rear panel sockets overview
The TANDBERG Codec C90 offers a great flexibility
in connecting audio and video equipment to the
system.
The illustration below shows the rear panel of the
TANDBERG Codec C90.
Inputs Outputs TANDBERG Basic
1
* Not supported in version 1
** For future use
1
Codec C90 Rear Panel
Setup
The main connectors
for TANDBERG basic
setup are highlighted
in orange.
Video sockets
The video input sockets are:
4 x HDMI
4 x HD-SDI
2 x DVI-I
2 x Analog Component (Y-Pr-Pb)
1 x Composite* or 1 x S-Video( YC)*
The video output sockets are:
2 x HDMI
2 x DVI-I
1 Composite
Audio socketsVideo sockets
Audio sockets
The audio input sockets are:
8 x XLR Female - Microphone /Line In
4 x RCA - Line In (1 Lef t, 2 Right, 3 Left, 4 Right)
2 x HDMI
The audio output sockets are:
2 x XLR Male - Line Out
4 x RCA - 1 Left ( SPDIF ), 2 Right, 3 Left
(SPDIF), 4 Right
2 x HDMI
The following pages gives a detailed description of the rear panel sockets and connectors.
Other sockets
The other sockets are:
Ethernet 1 and Ethernet 2*
COM - Serial data port
Camera control - Serial port for camera control
Power socket
Grounding - Chassis grounding
Power On/Off switch
GPIO**, USB Host**, USB Device**, T Link**
D14128.02—NOVEMBER 2008
GPIO and USB
Audio socketsVideo sockets Network
T Link
interface
sockets
COM Port,
Camera
Control
Power
socket
Power
switch
17
Codec C90
Interfaces
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
The Video Input Matrix
The video input matrix is found at the rear side of the codec and
illustrates the combinations in which the video inputs can be
connected.
About the matrix
Only one video input source from each row can be active at any time.
The numbers in the left column represents the Video Input Sources
1–5. The main connectors, which are used in basic setup, are marked
in orange color.
The Comp. 5 and S-Video (YC) 5 inputs uses the same physical
connectors and can not be connected at the same time.
Configure the video inputs
You can configure the video input settings from the Administrator
Settings menu or by running API commands.
The default configurations are shown below:
What connectors are active is determined by the configuration of
the video input connector settings:
Video Input Source 1 Connector: HDMI•
Video Input Source 2 Connector: HDMI•
Video Input Source 3 Connector: DVI•
Video Input Source 4 Connector: HDMI•
Video Input Source 5 Connector: DVI•
The video name of the connector inputs should be set:
Video Input Source 1 Name: “Main Camera“•
Video Input Source 2 Name: “Secondar y Camera“•
Video Input Source 3 Name: “PC“•
Video Input Source 4 Name: “DVD“•
Video Input Source 5 Name: “Document Camera“•
The video quality of the connector inputs should be set:
Video Input Source 1 Quality: Motion•
Video Input Source 2 Quality: Motion•
Video Input Source 3 Quality: Sharpness•
Video Input Source 4 Quality: Motion•
Video Input Source 5 Quality: Sharpness•
To determine the main video source and the default presentation
source for the system the following setting must be configured:
Video MainVideoSource: 1•
Video DefaultPresentationSource: 3•
Video input matrix
Input Sources Connector Name
1 1st Camera HDMI 1 HD-SDI 1 YPrPb 1
2 2nd Ca mera HDMI 2 HD-SDI 2 YPrPb 2
3 PC HDMI 3 HD-SDI 3 DVI-I 3
4 HDMI 4 HD-SDI 4 –
5 DVI-I 5 Comp. 5* YC 5*
* Comp 5 and YC 5 are not supporte d in version 1
Administrator settings
Open the menu on screen to configure the video input sources
and which of the sources should be the main video source and
the default presentation source.
If the system is in standby mode, press any key on the remote
control to wake up the system.
Select: Settings > Administrator Settings > Advanced 1.
Configurations
From this point you can:2.
Search for the words “source” or “video” to see a list •
of the available Video Input Source [1–5] Connector
settings
- or,• you can navigate down in the list to Video > Input >
Source 1 > Connector
On the remote control, press the right arrow to edit the 3.
values
Select a value and press Save, or press Cancel to leave •
without saving.
Proceed and configure the:4.
Video Input Source Name, for the current input•
Video Input Source Quality, for the current input•
Video Main Video Source, for the system•
Video Default Presentation Source, for the system•
API commands
Open a telnet or ftp session to the codec to issue an API command to
configure the video input sources and which of the sources should be the
main video source and the default presentation source.
The following commands determines which connector to be active:
xconfiguration video input sou rce 1 con nector: hdm i•
xconfiguration video input sou rce 2 con nector: hdm i•
xconfiguration video input sou rce 3 con nector: dvi•
xconfiguration video input sou rce 4 con nector: hdm i•
xconfiguration video input sou rce 5 con nector: dvi•
Set the video quality and a name of the video inputs 1 to 5:
xconfiguration video input sou rce 1 quality: motion•
xconfiguration video input sou rce 1 na me: “Main Cam era“•
Configure the video inputs 2 to 5•
The main video source is the camera, connected to video input source 1:
xconfiguration video mainvideosource: 1•
The default presentation source is a PC, connected to video input source 3:
xconfiguration video defaultpresentationsource: 3•
D14128.02—NOVEMBER 2008
18
Codec C90
Interfaces
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Video inputs (I)
All video inputs can not be active at the same
time. Please refer to the Video Input Matrix on the
previous page to see an overview.
Component 1–2 (Y-Pr-Pb)
2 x 3 BNC sockets, analog video input 1, 2.
There are three BNC connectors for each
Component inter face ; Y (luma), Pr ( red), Pb (blue).
Typical use. Camera, DVD and Content player.
HD-SDI 1–4
4 BNC sockets, digital video input 1, 2, 3, 4.
Typical use. Cameras.
Composite 5* / S-Video (YC) 5*
2 BNC sockets, analog video input 5.
* Comp 5 and YC 5 are not supported in version 1.
The S-Video (YC) and the composite inputs uses
the same physical connectors, and will not be able
to be connected at the same time.
S-Video 5 - Connect to the Y/Comp 5 (luma) •
and C 5 (chroma) connectors
Composite 5 - Connect to Comp 5 connector•
Typical use. Camera and DVD.
BNC pin-out
External view of socket
4 x HD-SDI In
GNDSignal
2 x Component In
(YPrPb)
1 x Composite *
or 1 x S-Video* (YC )
BNC: Bayonet Neill-Concelman
HD-SDI: High Definition - Serial Digital Interface
Y-Pr-Pb: Y: Information about luma (luminance);
Pr: Red color; Pb: Blue color
Y-C: Y: Information about luma (luminance ); C:
Information about chroma (color)
Video input formats supported
HD-SDI
1920x1080@30Hz
1920x1080@25Hz
128 0x72 0@ 60Hz
1280x720@50Hz
1280x720@30Hz
128 0x72 0@ 25Hz
Analog component
1920x1080@60Hz
1920x1080@50Hz
1920x1080@30Hz
1920x1080@25Hz
128 0x72 0@ 60Hz
1280x720@50Hz
1280x720@30Hz
720x576@50Hz
720x48 0@60Hz
Composite/S -Video
PAL / NTSC
Levels
HD-SDI
0.8 Vpp, 75 Ω
SMPTE 259M ( 270 Mbps)
SMPTE 292M (1.485, 1.485/1.001 Gbps)
D14128.02—NOVEMBER 2008
Y-Pb-Pr
Y: 1V Vpp, 75 Ω
Pb: 0.7 Vpp, 75 Ω
Pr: 0.7 Vpp, 75 Ω
Composite. 1 Vpp, 75 Ω
S-Video ( YC)
Y: 1 Vpp, 75 Ω
C (PAL): 0.3 Vpp, 75 Ω
C (NTSC ): 0.28 Vpp, 75 Ω
19
Codec C90
Interfaces
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Video inputs (II)
All video inputs can not be active at the same time.
Please refer to the Video Input Matrix (two pages
back) to see an overview.
HDMI 1–4
4 x HDMI sockets, digital video input 1–4. Audio
input on 3 and 4.
HDMI - High Definition Multimedia Interface (digital,
sound & picture)
Typical use. Camera, DVD, PC.
Main connector. The HDMI 1 input is the main
connector to the PrecisionHD 1080p camera.
DVI-I 3 and 5
2 x DVI-I sockets, digital/analog video input 3, 5.
DVI-D •
DVI-A (Analog RGB / VGA)•
DVI-I - Digital Video Interface - Integrated (digital
DVI-D and analog DVI-A)
Typical use. Two digital video inputs for PC
presentations or used for the TANDBERG Precision
HD Camera.
Main connector. The DVI-I 3 is the main
connector for PC input.
DVI-I pin-out
External view of socket
4 x HDMI In
2 x DVI-I In
Video input formats supported
DVI-D/HDMI
1920x1080@60Hz
1920x1080@50Hz
1920x1080@30Hz
1920x1080@25Hz
1920x1080@24Hz
1280x720@60Hz
1280x720@50Hz
720x48 0@60Hz
DVI-A
640x480 @72, 75, 85 Hz (VGA)
800x600@56, 60, 72, 75, 85 Hz (SVGA)
1024x768@60, 70, 75, 85 Hz (XGA)
1280x1024@60, 75 Hz (SXGA)
HDMI pin-out
External view of socket
Pin: 19 17 3 1
Pin: 18 16 4 2
D14128.02—NOVEMBER 2008
HDMI Pin-out
Pin Assignment Pin Assignment
1 T.M.D.S. Data 2+ 11 T.M.D.S. Clock Shield
2 T.M.D.S. Data 2 Shield 12 T.M.D.S. Clock–
3 T.M.D.S. Data 2 – 13 CEC
4 T.M.D.S. Data 1 14 Reserved (N.C. on device )
5 T.M.D.S. Data 1 Shield 15 SCL
6 T.M.D.S. Data 1 – 16 SDA
7 T.M.D.S. Data 0 17 DDC/CEC Ground
8 T.M.D.S. Data 0 Shield 18 +5 V Power (ma x 50 mA)
9 T.M.D.S. Data 0 – 19 Hot Plug Detect
10 T.M.D.S. Clock+
20
Codec C90
Interfaces
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Video outputs
HDMI 1 and 3
2 x HDMI sockets, digital video and audio output
1, 3.
HDMI - High Definition Multimedia Interface (digital,
sound & picture)
Typical use. Monitor, recording device
Main connector. The HDMI output 1 is the main
connector to the monitor.
Dual monitor. Dual output is provided on HDMI
output 3.
DVI-I 2 and 4
2 x DVI-I sockets, digital/analog video output 2, 4.
DVI-D•
DVI-A (Analog RGB / VGA)•
DVI-I - Digital Video Interface - Integrated (digital
DVI-D and analog DVI-A)
Typical use. Monitors.
Composite 5
1 x BNC sockets, analog video output 5.
Typical use. Monitor.
BNC pin-out
External view of socket
2 x HDMI
GNDSignal
1 x Composite Out2 x DVI-I Out
DVI-I pin-out
External view of socket
Video output formats supported
DVI-D/DVI-I/HDMI
1920x1080@60fps ( HD1080p60)
1280x720@60fps (HD720p60)
1366x768@60fps (WXGA)
1280x768@60fps (WXGA)
1024x768@60fps ( XGA)
1280x1024@60fps ( SXGA)
640x480 @60fps ( VGA)
800x600@60fps (SVGA)
Composite
PAL / NTSC
Levels
Composite. 1 Vpp, 75 Ω
D14128.02—NOVEMBER 2008
BNC - Bayonet Neill-Concelman
HDMI pin-out
External view of socket
Pin: 19 17 3 1
Pin: 18 16 4 2
Please refer to previous page for pin-out scheme.
21
Codec C90
Interfaces
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Audio inputs (I)
Unused, but connected audio inputs should be set
to Off to avoid unwanted audio/noise.
Microphone/Line In 1–8 (XLR)
8 x Balanced XLR sockets, audio input 1–8.
Main connector. The Microphone /Line In 1 is the
main connector for the microphone.
All eight microphone inputs are for balanced
electret microphones, 48V phantom powered via
XLR connectors.
The phantom powering of all eight XLR sockets can
be individually switched off. The input will then be a
balanced line level input.
All Microphone /Line In 1–8 are equipped with
acoustic echo canceller.
Use Microphone /Line In 1–8 to connect to an
external microphone amplifier or an external mixer.
Default configuration. In default configuration,
all Microphone /Line In inputs are enabled and
configured as microphones.
2 x HDMI In
8 x Microphone / Line In
HDMI In 3, 4
2 x HDMI connectors, audio input 3, 4
Typical use. Use HDMI In 3 or 4 (2–8 channels)
to connect to external playback devices as DVD
players. Each input support up to two channels at
48kHz sampling rate.
D14128.02—NOVEMBER 2008
XLR pin-out
External view of socket
Pin 1: Gnd
12
Pin 2: Hot
3
XLR - Electrical Connector (Cannon XL series with
Rubber compound)
Pin 3: Cold/neutral
HDMI pin-out
External view of socket
Pin: 19 17 3 1
Pin: 18 16 4 2
Please refer to previous page for pin-out scheme.
22
Codec C90
Interfaces
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Audio inputs (II)
Unused, but connected audio inputs should be set
to Off to avoid unwanted audio/noise.
Line In 1–4 (RCA)
4 x RCA sockets, audio input 1–4
Audio Line In 1–4 are used when connecting to PC
and to external playback devices, such as VCR’s
or DVD players.
Main connectors. The Line In 1 (left) and Line In
2 (right) are the main connectors to a PC.
Stereo. For systems with stereo I/O the audio
inputs can be configured in stereo pairs:
Connect the left channel to Line In 1 or 3 •
Connect the right channel to Line In 2 or 4•
Default configuration for Line In 1–2 . In the
default configuration Line In 1 and 2 are configured
as stereo inputs for ex ternal playback devices,
such as a PC.
Default configuration for Line In 3 –4. In the
default configuration Line In 3 and 4 are configured
as stereo input pairs. The two inputs are paired
with Line Out 3 and 4 respectively.
This pairing will avoid feedback situations that
can arise when playback /recording devices are in
standby mode (Loop suppression).
Line In 3 and 4 are used with external playback
devices as VCR’s and DVD players.
RCA pin-out
External view of socket
GNDSignal
4 x Line In
D14128.02—NOVEMBER 2008
RCA - Phono Plug (the Radio Corporation of
America)
23
Codec C90
Interfaces
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Audio outputs (I)
Line Out 5–6 (XLR)
2 x Balanced XLR sockets, audio output 5–6.
Audio Line Out 5–6 are balanced outputs, for
connection to balanced speakers.
Default configuration. In default configuration
Line Out 5 is configured as Lef t speaker, and Line
Out 6 is configured as right speaker.
HDMI Out 1, 3
2 x HDMI connectors, audio out 1, 3
Use HDMI Out 1 to connect to a flatscreen with
speakers. HDMI 1 will provide stereo audio speaker
signals at 48kHz.
Use HDMI Out 3 to connect to a DVD recorder.
HDMI will provide stereo line output signals at
48kHz. Includes local microphones.
Main connector. The HDMI output 1 is the main
connector to the monitor.
HDMI 1. Audio from far end and PC.
HDMI 3. All audio mixed together for recordings.
XLR pin-out
External view of socket
2 x HDMI Out
2 x Line Out (XLR male)
What is a Line output
A Line output consists of all signals from local
side and all signals from far end side.
Left channel
The Left channel consists of all Left channel and
Mono signals.
D14128.02—NOVEMBER 2008
Pin 1: Gnd
12
Pin 2: Hot
3
XLR - Electrical Connector (Cannon XL series with
Rubber compound)
Pin 3: Cold/neutral
What is a Speaker output
A Speaker output consists of all signals from
local side, except microphones, and all signals
from far end side.
Right channel
The Right channel consists of all Right channel
and Mono signals.
24
Codec C90
Interfaces
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Audio outputs (II)
Line Out 1–4 (RCA)
4 x RCA sockets, audio output 1-4
Can be configured as two stereo pairs.
Main connectors. Line Out 1 (left) and Line
Out 2 (right) are the main connectors to the local
loudspeaker system.
The local loudspeaker system may or may not
include the TANDBERG DNAM (Digital Natural
Audio Module).
Default configuration Line Out 1-2. In default
configuration, Line Out 1 and 2 are configured as
stereo speakers.
if a DNAM is present or SPDIF is active on Line Out
1, then Line Out 1 provides a digital stereo speaker
signal and Line Out 2 is not active.
Default configuration Line Out 3- 4. In default
configuration, Line Out 3 and 4 are configured as
stereo line out for external recording devices as
VCR’s or DVD recorders.
if a DNAM is present or SPDIF is active on Line Out
3, then Line Out 3 provides a digital stereo speaker
signal and Line Out 4 is not active.
SPDIF - Sony/Philips Digital Interface, used by the
Digital Natural Audio Module.
RCA pin-out
External view of socket
What is a Line output
A Line output consists of all signals from local
side and all signals from far end side.
GNDSignal
4 x Line Out
Left channel
The Left channel consists of all Left channel and
Mono signals.
D14128.02—NOVEMBER 2008
RCA - Phono Plug (the Radio Corporation of
America)
What is a Speaker output
A Speaker output consists of all signals from
local side, except microphones, and all signals
from far end side.
Right channel
The Right channel consists of all Right channel
and Mono signals.
25
Codec C90
Interfaces
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Audio Signal Levels tables
Microphone Inputs 1 to 8
XLR female
Signa l
levels
Level
setting
[dB] [mVpp] [dBu ] [dBu]
Clipping level Nominal
level
0.0 275.0 -18. 0 -36.0
1.0 2 45 .1 -19.0 - 37. 0
2.0 218 .4 -20.0 -38.0
3.0 194 .7 -2 1.0 -39.0
4.0 173. 5 -22.0 -40.0
5.0 154.6 -23.0 -41. 0
6.0 13 7. 8 -24.0 -42.0
7. 0 122.8 -25.0 -43.0
8.0 109. 5 -26.0 -44.0
9.0 9 7.6 -27.0 -45.0
10.0 8 7.0 -28.0 -46.0
11. 0 7 7.5 -29.0 - 47. 0
12.0 6 9.1 -30.0 -48.0
13.0 61.6 -31.0 -49.0
14. 0 54.9 -32.0 -50.0
15.0 48.9 -33.0 - 51.0
16.0 43.6 -34.0 -52.0
17. 0 38.8 -35.0 -53.0
18.0 34.6 -36.0 -54.0
This specification is valid for Mic 1–8 inputs if
Microphone Level setting is selected.
Line Inputs 1 to 8
XLR female
Signa l
levels
Level
setting
[dB] [Vpp ] [ dBu] [dBu]
Clipping level Nominal
level
0.0 34.7 24.0 6.0
1.0 31.0 23.0 5.0
2.0 27. 6 22.0 4.0
3.0 24. 6 21.0 3.0
4.0 21.9 20.0 2.0
5.0 19. 5 19.0 1.0
6.0 17. 4 18. 0 0.0
7. 0 15.5 17. 0 -1.0
8.0 13.8 16.0 -2.0
9.0 12.3 15 .0 -3.0
10.0 11. 0 14.0 -4.0
11. 0 9.8 13 .0 -5.0
12.0 8.7 12.0 -6.0
13.0 7. 8 11. 0 -7. 0
14.0 6.9 10 .0 -8.0
15.0 6.2 9.0 -9.0
16.0 5.5 8.0 -10.0
17. 0 4.9 7. 0 -11 .0
18.0 4.4 6.0 -12. 0
This specification is valid for Line 1-8 inputs if Line
Level setting is selected.
Line outputs 5 to 6
XLR male
Signa l
levels
Level
setting
[dB] [Vpp ] [ dBu] [dBu]
–18.0 4.4 6.0 -12. 0
–1 7.0 4.9 7.0 -11.0
–16.0 5.5 8.0 -10 .0
–15.0 6.2 9.0 -9.0
–14. 0 6.9 10 .0 -8.0
–13.0 7. 8 11. 0 - 7.0
–12.0 8.7 12 .0 -6.0
–11. 0 9.8 13.0 -5.0
–10.0 11. 0 14. 0 -4.0
Absolute ma x
output level
–9.0 12.4 15.0 -3.0
–8.0 13 .9 16 .0 -2.0
–7. 0 15.6 1 7.0 -1.0
–6.0 17. 5 18.0 0.0
–5.0 19 .6 19.0 1. 0
–4.0 22.0 20.0 2.0
–3.0 24.7 21. 0 3.0
–2.0 2 7.7 22.0 4.0
–1.0 31.0 23.0 5.0
0.0 34.8 24.0 6.0
Nominal
level
Line Inputs 1 to 4
Female RCA/phone
Signa l
levels
Level
setting
[dB] [Vpp ] [ dBu] [dBu]
Clipping level Nominal
level
0.0 17. 4 18.0 0.0
1.0 15.5 1 7.0 -1.0
2.0 13 .8 16 .0 -2.0
3.0 12.3 15 .0 -3.0
4.0 11 .0 14 .0 -4.0
5.0 9.8 13.0 -5.0
6.0 8.7 12.0 -6.0
7. 0 7.8 11.0 - 7.0
8.0 6.9 10.0 -8.0
9.0 6.2 9.0 -9.0
10.0 5.5 8.0 -10.0
11. 0 4.9 7.0 - 11.0
12.0 4.4 6.0 -12. 0
13.0 3.9 5.0 -1 3.0
14.0 3.5 4.0 -14. 0
15.0 3 .1 3.0 -15. 0
16.0 2.8 2.0 -1 6.0
17. 0 2.5 1. 0 -1 7.0
18.0 2.2 0.0 -18 .0
Notes:
Default levels are marked with white text on black1.
For the dBu value for input clipping level and absolute max output level, a sine waveform is 2.
assumed
If numbers in dBV are required, dBV value is 2.2 dB lower than the dBu value. 3.
Example: -10 dBu equals -12.2 dBV
D14128.02—NOVEMBER 2008
26
Codec C90
Interfaces
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Audio signal levels, cont...
Line outputs 1 to 4
Female RCA/phone
Signa l
levels
Level
setting
[dB] [Vpp ] [ dBu] [dBu]
-18 .0 2.2 0.0 -18 .0
-17. 0 2.5 1.0 -17.0
-16 .0 2.8 2.0 -1 6.0
-15.0 3 .1 3.0 -15. 0
-14. 0 3.5 4.0 -14 .0
-13.0 3.9 5.0 -13. 0
-12. 0 4.4 6.0 -12. 0
-11. 0 4.9 7.0 -11.0
-10.0 5.5 8.0 -10.0
Notes:
Default levels are marked with white text 1.
on black
For the dBu value for input clipping level 2.
and absolute max output level, a sine
waveform is assumed
If numbers in dBV are required, dBV value 3.
is 2.2 dB lower than the dBu value.
Example: -10 dBu equals -12.2 dBV
Absolute ma x
output level
-9.0 6.2 9.0 -9.0
-8.0 6.9 10.0 -8.0
-7. 0 7. 8 11. 0 - 7.0
-6.0 8.7 12.0 - 6.0
-5.0 9.8 13 .0 -5.0
-4.0 11. 0 14.0 -4.0
-3.0 12.3 15.0 -3.0
-2.0 13 .8 16 .0 -2.0
-1.0 15.5 17. 0 -1.0
0.0 17. 4 18.0 0.0
Nominal
level
Audio hardware information table
Hardware Information
Mic 1–8 * Line in 1–8 ** Line out 5 –6 Line in 1–4 Line out 1–4
Signa l type Balanced Balanced Balanced Unbalanced Unbalanced
Connector (codec) XLR-F XLR-F XLR-M Female RCA /phono Female RCA/phono
Input impedance 8100 Ohm ( pin 2–3) 10k Ohm (pin 2–3) 10 k Ohm
Output impedance 50 Ohm 100 Ohm
Max input level when set to Min input level –18dBu/275mVpp 24dBu/34.7Vpp 18dBu/17.4Vpp
Max input level when set to Max input level –36dBu/35mVpp 6dBu/4.4Vpp 0.0dBu /2.2Vpp
Max output level when set to Min output level 6dBu/4.4Vpp 0dBu/2.2Vpp
Max output level when set to Max output level 24dBu/34.8Vpp 18dBu/17.4Vpp
Gain range <– 18dB (18 steps of 1dB) –>
Phantom power 48 Volt +/- 2%
Phantom power resistor pin 1 6800 Ohm
Phantom power resistor pin 2 6800 Ohm
Max phantom power current (per mic) 14m A
* This specification is valid for Mic 1–8 inputs if Microphone Level setting is selected
** This specification is valid for Line 1-8 inputs if Line Level setting is selected
Volume control table
Volume control
Ring tone volume* Audio ga in value
0 0
1 -34.5 dB
70 0.0 dB
100 15.0 dB
* The ring tone volu me whic h is displayed on screen,
when us ing the TRC5 remote c ontrol, goes from 0 to 20.
D14128.02—NOVEMBER 2008
27
Codec C90
Interfaces
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Network connectors
Ethernet interface
2 × Gigabit Ethernet LAN (RJ-45 Jack) interface
(GbE).
Ethernet 1: Main connector for network connection
Ethernet 2: For future use.
Ethernet 1
Ethernet 2
(for future use)
D14128.02—NOVEMBER 2008
RJ-45 Connector pin-out
1 8
TOP
FRONT
1 8
Wiring diagram
standard cable
1 ---------- 1
2 ---------- 2
3 ---------- 3
6 ---------- 6
28
Codec C90
Interfaces
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
COM port and Camera Control port
COM port
1 x COM (RS-232) data port for codec control and
configuration through API commands.
Camera Control port
1 x Camera Control ( RS-232) port for power and
camera control (pan, tilt, zoom) using the VISCA™*
protocol.
Main connector. The main camera is connected
to the Camera Control port.
Power. Pin No. 4 on the Camera Control port
provides 12 V DC / 1 A to the main camera.
If more than one camera is connected, only the first
camera is powered from the codec. The additional
cameras must be daisy chained by using a serial
cable and external power.
Additional cameras. For information about
additional cameras, go to the Cameras section
later in this guide.
COM por t
Camera Control Por t
*VISCA™ is a trademark of Sony Corporation
RS232 9 pin D-SUB pin-out
External view of socket
1 5
6 9
D14128.02—NOVEMBER 2008
Pin-out—COM Port
Pin Signal name Direction
Carrier detect, CD From DCE
1
Receive data, RXD From DCE
2
Transmit data, TXD To DCE
3
12 V / 1 A To the main camera
4
Signal GND
5
6 Data set ready, DSR
7 Ready to send, RTS
8 Clear to send, CTS
9 Ring indicator, RI
From DCE
To DCE
From DCE
From DCE
Pin-out—VISCA™ camera control
RJ11, 8 pins shielded modular jack
Pin Signal n ame
8 +12V (presence 2.8m A current source
when connected in daisy chain)
7 GND
6 TXD ( out)
5 NC (no connect)
4 NC (no connect)
3 RXD (in)
2 GND
1 +12V
Pin-out—TANDBERG camera cable
Signa l
name
+12V DC 1 Twisted
GND 2 5
RX 3 Twisted
TX 6 3
NC 4 Twisted
NC 5 6
GND 7 Twisted
+12V DC 8 4
RJ-45 pin D -SUB pin
pair
pair
pair
pair
4
2
1
5
29
Codec C90
Interfaces
Contents Introduction Getting Star ted Interfaces About the API xConfiguration xCommand xStatus Cameras Appendices Contact us
System Integrator Guide
Power
Power socket
Power Cord Socket.
Accepts 100-240V, 50/60Hz, 2.8A max.
CAUTI ON! This equipment must be grounded.
Power switch
Power Switch (On /Of f)
Chassis grounding
For grounding of the chassis
Power
Socket
Chassis
Grounding
Power
Switch
D14128.02—NOVEMBER 2008
30
Loading...