Sony SCPH-10173, SCPH-10172 Instruction Manual

DVD Remote Control

(for PlayStation®2) with IR Receiver Unit

Instruction Manual

Thank you for purchasing the DVD Remote Control (for PlayStation Control is exclusively for use with the PlayStation entertainment system.

®2) with IR Receiver Unit. This DVD Remote

®2 computer

SCPH-10173

3-069-287-32(1)

Precautions

This product has been designed with the highest concern for safety. However, any electrical device, if used improperly, has the potential for causing fire, electrical shock or personal injury. To ensure accident-free operation, be sure to follow these guidelines:

• Do not use the device if it functions in an abnormal manner.

• Keep the IR receiver unit (for PlayStation®2) in a place out of the reach of small children. If swallowed, the IR receiver unit can cause choking.

• Never disassemble or modify the DVD Remote Control or IR receiver unit.

• Keep the DVD Remote Control and IR receiver unit away from heat and dust, and from smoky, greasy or humid locations.

• Do not leave the DVD Remote Control or IR receiver unit on the floor.

• Do not allow liquid or small particles to get into the DVD Remote Control or IR receiver unit.

• Dispose of all packaging materials and worn-out products properly.

• If the device does not function properly, please contact the appropriate PlayStation® customer service helpline which can be found within every PlayStation® and PlayStation®2 format software manual.

Table of contents

Precautions .................................... 2

Discs that can be played with the

PlayStation®2 console .............. 4

Setup ...................... 5

Before use .......................................... 5

Notes on use ....................................... 5

Inserting batteries into the

DVD Remote Control (for PlayStation

Attaching the IR receiver unit

(for PlayStation

®2) ....................... 6

®2) ....................... 7

Startup with the supplied DVD Player

disc ........................ 8

Installing the DVD Player

on a Memory Card (8MB) (for PlayStation

®2) ....................... 8

Viewing a DVD

video .................... 10

Playback of a DVD video ................ 10

When the DVD video is

finished ....................................... 11

Operating the DVD Player ............... 11

About the Control Panel .................. 12

Using the DVD Remote Control

(for PlayStation

Direct button operation with the

Analog Controller (DUALSHOCK

®2) ..................... 16

®2) ..................... 18

Playback from the last stopping

point (Resume Play) ................... 20

Playback in desired order

(Program Play) ........................... 21

Playback in random order

(Shuffle Play).............................. 23

Repeated playback

(Repeat Play) .............................. 24

Repeated playback of a selected

section (AyB Repeat) ............. 25

Using the Control

Panel .................... 26

Selecting a specific scene for

playback ...................................... 27

Displaying title and chapter

numbers ...................................... 28

Finding a particular point on

a disc (Search) ............................ 29

Setup display item list ...................... 30

Troubleshooting ... 31

Specifications ...... 33

Discs that can be played with the PlayStation

The following discs can be played on the PlayStation®2 console:

2 console

Disc type

Disc logo

Contents

Disc size

Play time

DVD video systems and regional restrictions

• This console conforms to the PAL broadcast standard. You cannot play discs recorded for other broadcast standards (such as NTSC) on this console (unless the NTSC disc displays the compatible TV is used).

• Most DVD videos are marked with region numbers such as 4. The number contained within the symbol represents the region number of DVD players on which the disc can be played. DVD videos that do not bear this symbol, or that do not display the number 4, cannot be played on your console.

• DVDs with the to play any other DVDs, a message stating, “This disc cannot be played due to regional restrictions.” will appear onscreen.

• Some DVDs that have no region code markings may still be subject to area restrictions and may not be playable on the console.

About 4 hrs (single-sided) About 80 min (single-sided)

About 8 hrs (double-sided) About 160 min (double-sided)

ALL

label can also be played on this console. If you attempt

12 cm 8 cm

DVD video

The “DVD VIDEO” logo is a trademark.

Audio and video

ALL

label and an NTSC

Note on the playback of DVD video

This console plays DVD video as originally designed by the software producers. Some of the playback features of this console may not have been incorporated into the DVD video design. As a result, some playback features may not be available with certain software. Please refer to the instructions supplied with your DVD video for details.

Setup

Before use

Check that you have the following items:

• DVD Remote Control (for PlayStation®2) (1)

• IR receiver unit (for PlayStation

• DVD Player (for PlayStation

• R03 (AAA) batteries (2)

• Instruction manual (1)

If any items are missing, please contact the appropriate PlayStation® customer service helpline which can be found within every PlayStation® and PlayStation®2 format software manual.

Notes on use

• Some PlayStation®2 or PlayStation® format software may not function properly when operated using the DVD Remote Control (for PlayStation®2).

• The DVD Remote Control will not work if you push more than one button at a time.

• Two or more DVD Remote Controls or IR receiver units should not be used simultaneously.

®2) (1)

®2) disc (1)

Setup (continued)

Inserting batteries into the DVD Remote Control (for PlayStation®2)

Insert the two R03 (AAA) batteries (supplied) into the DVD Remote Control paying attention to the plus and minus terminals (polarity) as indicated in the battery compartment.

Notes

• Incorrect use of batteries can result in battery content leakage or explosion.

When using batteries, be sure to abide by the following instructions: – Make sure that the plus and minus terminals of the batteries are inserted in the

correct directions. – Do not mix old and new or different types of batteries. – Do not attempt to recharge non-rechargeable type batteries. – Remove the batteries when the DVD Remote Control will not be used for an

extended period of time. – If battery contents have leaked, be sure to carefully remove all residue before

inserting new batteries.

• When using the DVD Remote Control, be sure that the IR receiver of the IR receiver unit is not in direct sunlight or exposed to other strong light. The DVD Remote Control may not function properly under such conditions.

Attaching the IR receiver unit (for PlayStation®2)

Holding the IR receiver unit with the arrow mark facing up, securely insert the connector into a controller port of the PlayStation®2 console.

IR receiver unit (for PlayStation®2)

IR receiver

Note

When using the IR receiver unit for the first time, be sure to remove the protective scratch resistant film before inserting the unit into the PlayStation

®2 console.

Startup with the supplied DVD Player disc

To use all DVD Remote Control functions, you may need to install the DVD Player (for PlayStation®2) on a Memory Card (8MB) (for PlayStation®2) (sold separately). For details, refer to the “Notes” section on page 9.

1 Press the MAIN POWER switch on the PlayStation®2 console rear

to turn the console on.

The 1 indicator turns red, and the console is in standby mode.

2 Press the 1/RESET button.

The 1 indicator turns green, and the console startup screen is displayed.

3 Press the A button.

The disc tray opens.

4 Place the disc into the disc tray with the label side facing up. 5 Press the A button.

The disc tray closes. Once the disc has started, the disc startup screen is displayed.

Note

The DVD Player (for PlayStation®2) is software that allows playback of DVD videos on the PlayStation

Installing the DVD Player on a Memory

®2 console.

Card (8MB) (for PlayStation®2)

The DVD Player must be installed on a Memory Card (8MB) (for PlayStation®2) (sold separately). If you delete the DVD Player, you can install it from the supplied disc again at any time.

1 Insert the Memory Card (8MB) (for PlayStation®2) into MEMORY

CARD slot 1 of the PlayStation®2 console.

2 Start the supplied DVD Player disc. 3 On the startup screen, press the ✕ button.

The Basic Operations screen is displayed.

4 With the Basic Operations screen displayed, press the ✕ button.

The Menu screen is displayed.

5 Select the “Installing DVD Player” option from the Menu screen

and press the ✕ button.

Complete the installation following the onscreen instructions.

Notes

• To view DVD video using the DVD Player installed on a Memory Card (8MB) (for PlayStation PlayStation

• Some DVD Remote Control functions will not work if you use DVD Player software earlier than version 2.00. Refer to the PlayStation®2 console instruction manual for details on how to check the version of your DVD Player software. For PlayStation®2 consoles of model numbers SCPH-30002 and SCPH-35002GT, you must install DVD Player (ver 2.00), or later, on a Memory Card (8MB) (for PlayStation

• Before installing the DVD Player on the Memory Card (8MB) (for PlayStation on the Memory Card.

• Insert the Memory Card (8MB) (for PlayStation®2) into MEMORY CARD slot 1 of the PlayStation Card in MEMORY CARD slot 2.

• Do not remove the Memory Card (8MB) (for PlayStation®2) while the installation is in progress. The installation will be incomplete if the Memory Card is removed or the PlayStation installing.

®2), you must insert the Memory Card (8MB) (for

®2) into a MEMORY CARD slot of the PlayStation®2 console.

2) to activate all DVD Remote Control functions.

®2), be sure that at least 2,200 KB (2.2MB) of free space is available

®2 console. Installation is not possible with the Memory

®2 console is turned off or reset while

Viewing a DVD video

To view DVD video using the DVD Player installed on a Memory Card (8MB)

(for PlayStation into a MEMORY CARD slot of the PlayStation Some DVD Remote Control functions will not work if you use DVD Player software earlier than version 2.00. Refer to the PlayStation manual for details on how to check the version of your DVD Player software. For PlayStation®2 consoles of model numbers SCPH-30002 and SCPH-35002GT, you must install DVD Player (ver 2.00), or later, on a Memory Card (8MB) (for PlayStation®2) to activate all DVD Remote Control functions. For detailed installation instructions, see “Installing the DVD Player on a Memory Card (8MB) (for PlayStation

Playback of a DVD video

1 Insert the Memory Card (8MB) (for PlayStation®2) containing the

installed DVD Player into any MEMORY CARD slot of the PlayStation®2 console.

2 Press the MAIN POWER switch on the PlayStation®2 console rear

to turn the console on.

3 Press the 1/RESET button. 4 Press the A button. 5 Insert the DVD video you would like to play into the disc tray

with the label side facing up.

6 Press the A button.

The disc tray will close and playback will begin.

2), you must insert the Memory Card (8MB) (for PlayStation®2)

2 console.

2 console instruction

2)” on pages 8-9.

Notes

• Do not remove the Memory Card (8MB) (for PlayStation®2) containing the DVD Player before playback of the DVD video begins.

• With some discs, playback will not begin immediately, but a Title menu or DVD menu will be displayed.

• After the DVD video has finished playing, press the A button on the console to eject the disc and display the browser screen.

• If the power is turned off during playback, any optional settings you have made will be lost.

Notes on the playback of DTS audio from a DVD video

DTS audio signal can only be output through an optical digital cable (sold separately). Please note that it cannot be output through a regular audio cable.

• Do not set the “DTS” option of “Audio Digital Out” under “Audio Setup” to “On” when using an audio component that does not have a built-in DTS decoder. In such cases, if the “DTS” option is set to “On”, a loud noise (or no noise) will come from the speakers, possibly hurting your ears or damaging the speakers.

• When the “DTS” option of “Audio Digital Out” under “Audio Setup” is set to “Off”, the DVD’s DTS audio output will not be played back, even if you connect with an optical digital cable.

When the DVD video is finished

1 Press the A button on the PlayStation®2 console. 2 Remove the disc. 3 Press the A button.

Note: After changing DVD settings

To save your changes, be sure to eject the DVD before pressing the 1/RESET button or turning off the console with the MAIN POWER switch. Please note that changes will not be saved if you reset or turn off the console without first ejecting the DVD.

Operating the DVD Player

The DVD Player can be operated using the buttons of the DVD Remote Control, the direct buttons of the Analog Controller (DUALSHOCK®2) or from the onscreen Control Panel.

Notes

• Depending on the disc used, some operations may vary or may not be possible.

• The method of operation for certain functions may vary depending on whether the IR receiver unit is inserted into the PlayStation

®2 console or not.

+ 25 hidden pages

Sony SCPH-10173, SCPH-10172 Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Precautions

Setup

Before use

Notes on use

Inserting batteries into the DVD Remote Control (for PlayStation®2)

Attaching the IR receiver unit (for PlayStation®2)

Startup with the supplied DVD Player disc

Viewing a DVD video

Playback of a DVD video

When the DVD video is finished

Operating the DVD Player