How it Works
Sony
Loading...
MHC-V909AV

Sony MHC-V909AV Operating Instructions Manual

Mini Hi-Fi Component System
Operating Instructions
3-860-316-11(1)
MHC-V909AV
©1997 by Sony Corporation
SONY MHC-V909AV (E) 3-860-316-11(1)Actual page number:
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.
Laser component in this product is capable of emitting radiation exceeding the limit for Class 1.
This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.
This caution label is located inside the unit.
This stereo system is equipped with the Dolby Pro Logic Surround system* and the Dolby B-type noise reduction system. * Manufactured under license from Dolby Laboratories Licensing Corporation. DOLBY, the double-D symbol a and “PRO LOGIC” are trademarks of Dolby Laboratories Licensing Corporation.
This system can play the following discs:
VIDEO CDs Audio CDs
Disc logo
Contents Audio + Video Audio
(moving pictures) Disc size 12 cm/8 cm 12 cm/8 cm Play time 74 min./20 min. 74 min./20 min.
Note on VIDEO CDs
This system conforms to VIDEO CDs without PBC* functions (Ver. 1.1) and VIDEO CDs with PBC* functions (Ver. 2.0) of VIDEO CD standards. You can enjoy two kinds of playback according to the disc type.
Disc type You can
VIDEO CDs without Enjoy video playback PBC functions (moving pictures) as (Ver. 1.1 discs) well as audio CDs.
VIDEO CDs with Play interactive PBC functions software using menu (Ver. 2.0 discs) screens displayed on
the TV screen (menu playback), in addition to the video playback function of VIDEO CDs without PBC functions. Moreover, you can play high or standard quality still picture.
2
* PBC = PlayBack Control
SONY MHC-V909AV (E) 3-860-316-11Actual page number:
Table of Contents
Getting Started
Step 1: Hooking up the system............. 4
Step 2: Setting up your speakers .......... 8
Step 3: Setting the time ........................ 10
Step 4: Presetting radio stations ......... 11
Connecting optional AV components 12
Basic Operations
Playing a VIDEO CD ........................... 15
Playing a CD ......................................... 17
Recording a CD/VIDEO CD .............. 18
Listening to the radio........................... 20
Recording from the radio .................... 22
Playing a tape........................................ 24
Recording from a tape ......................... 26
Singing along: Karaoke ....................... 27
The VIDEO CD/CD Player
Playing a VIDEO CD with PBC
functions (Ver 2.0) ......................... 29
Checking the remaining time ............. 31
Using the on-screen display ............... 32
Locating a specific part of a disc ........ 34
Playing a VIDEO CD from where it was
last stopped..................................... 39
Reducing distortion of the picture with
advanced DNR ............................... 40
Setting the sharpness ........................... 41
Adding trails to moving pictures....... 41
Playing CD tracks repeatedly ............. 42
Playing CD tracks in random order ......
.......................................................... 43
Programming CD tracks ..................... 44
Playing CDs without interruption ..... 45
The Tape Deck
Recording on a tape manually ........... 46
Recording a CD by specifying track
order ................................................ 47
DJ Effects
Looping part of a CD ........................... 49
Flashing part of a CD ........................... 49
Waving the equalizer ........................... 50
Sound Adjustment
Adjusting the sound ............................ 51
Selecting the surround menu ............. 52
Enjoying the Dolby Pro Logic Surround
sound ............................................... 53
Selecting the audio emphasis ............. 53
Adjusting the audio emphasis............ 55
Making a personal audio emphasis
file .................................................... 56
Other Features
Mixing and recording sounds ............ 57
Falling asleep to music ........................ 58
Waking up to music ............................. 58
Timer-recording radio programs ....... 60
Additional Information
Precautions ............................................ 61
Troubleshooting ................................... 62
Specifications ........................................ 65
Glossary ................................................. 67
Index........................................ back cover
3
SONY MHC-V909AV (E) 3-860-316-11Actual page number:
Getting Started
Step 1: Hooking up the system
Do the following procedure 1 to 9 to hook up your system using the supplied cords and accessories.
AM loop antenna
FM lead antenna
Right
surround speaker
Left
surround speaker
Center
surround speaker
Right front speaker
4
Left front speaker
SONY MHC-V909AV (E) 3-860-316-11Actual page number:
Connect the front speakers.
1
Connect the speaker cords to the FRONT SPEAKER jacks of the same color.
Keep the speaker cords away from the antennas to prevent noise.
Insert only the stripped portion.
R
+
Connect the center speaker.
3
Connect the speaker cords to the CENTER SURROUND SPEAKER jacks of the same color.
Keep the speaker cords away from the antennas to prevent noise.
Insert only the stripped portion.
R
L
+
L
Red (‘)
Connect the rear speakers.
2
Black (’)
Connect the speaker cords to the SURROUND SPEAKER jacks of the same color.
Keep the speaker cords away from the antennas to prevent noise.
Insert only the stripped portion.
R
L
Red (‘)
+
Black (’)
+
–
Black (’)Red (‘)
Connect the FM/AM antennas.
4
+
–
Set up the AM loop antenna, then connect it.
Extend the FM lead
AM loop antenna
+
–
antenna horizontally.
FM75
AM
continued
5
SONY MHC-V909AV (E) 3-860-316-11Actual page number:
Step 1: Hooking up the system
VOLTAGE SELECTOR
110-120V 220-240V
(continued)
5 Connect the video input jack of your
TV to the VIDEO OUT jack with the supplied video connecting cable.
VID
EO
O
U
T
S VIDEO OUT
When using a TV
Turn on the TV and select the video input so you can view the pictures from this system.
Tip
For even higher quality video images, you can use an optional S VIDEO cord to connect the S VIDEO input jack on your TV to the S VIDEO OUT jack.
6 Set SYSTEM SELECT (color system)
to the appropriate position (PAL or NTSC), according to your TV.
NTSC AUTO PAL
SYSTEM SELECT
If your TV automatically changes the color system according to the input signal:
The factory setting (AUTO) automatically changes the color system of the video output according to the color system of the current VIDEO CD. If you turn off the system, the color system will be set to NTSC automatically when you turn on the system again.
If the color system of your TV is PAL:
Set SYSTEM SELECT to PAL.
Picture recorded in the NTSC color system will be stretched horizontally and will be displayed with the upper and lower parts of the screen masked in black.
Note
Be sure to turn off the system before changing the SYSTEM SELECT setting.
7 Set VOLTAGE SELECTOR to the
position of your local power line voltage (except for Thailand and Malaysian models).
8 Connect the power cord to a wall
outlet.
Demo mode appears in the display. If the plug on this unit does not fit your wall outlet, detach the supplied adapter from the plug (except for Malaysia and China).
9 Deactivate the demo mode by
pressing DISPLAY/DEMO when the system power is turned off.
If the color system of your TV is NTSC:
Set SYSTEM SELECT to NTSC.
Picture recorded in the PAL color system will be stretched vertically and will be displayed with the upper and lower parts of the picture cut off.
6
SONY MHC-V909AV (E) 3-860-316-11Actual page number:
Inserting two size AA (R6) batteries into the remote
Using the remote
You can use shaded the buttons shown below to operate Sony TV.
To attach the center speaker pads
Attach the supplied center speaker pads to the bottom of the center speaker to stabilize the speakers and prevent them from slipping.
To attach the front speaker pads
Attach the supplied front speaker pads to the bottom of the front speakers to stabilize the speakers and prevent them from slipping.
TV/VIDEO
To Press on the remote
Turn the TV on or TV POWER. off
Switch the TV's TV/VIDEO. video input
Change the TV TV CH +/–. channels
Adjusts the volume TV VOL +/–. of the TV speaker(s)
TV POWER TV VOL +/–
TV CH +/–
Tip
With normal use, the batteries should last for about six months. When the remote no longer operates the system, replace both batteries with new ones.
Note
If you do not use the remote for a long period of time, remove the batteries to avoid possible damage from battery leakage.
Tip
You can reinforce the bass sound by connecting an optional super woofer to the super woofer connector.
Note
You need to connect both left and right rear speakers. Otherwise, the sound will not be heard.
When carrying this system
Do the following to protect the CD mechanism.
1 Press FUNCTION repeatedly until “CD”
appears in the display.
2 Hold down PLAY MODE and press
POWER so “LOCK” appears in the display.
7
SONY MHC-V909AV (E) 3-860-316-11Actual page number:
Step 2: Setting up your speakers
Connecting the supplied rear and center speakers enables you to fully enjoy Dolby Pro Logic Surround sound. Dolby Pro Logic Surround is a decoding system standardized in TV programs and movies. Dolby Pro Logic Surround improves sound image by using four separate channels. These channels manipulate the sound to be heard and enhance the action as it happens on the screen.
Positioning the speakers
Before you connect them, determine the best location for your speakers.
1 Place the front speakers at an angle
of 45 degrees from your listening position.
Front speaker (L)
Center speaker
Front speaker (R)
2 Place the center speaker so it is
placed at about the same height as the front speakers (A). Align the center speaker with the front speakers or place it slightly back from the position of the front speakers (B).
A
B
Center speaker
3 Place the rear speakers facing each
other at about 60 to 90 cm above your listening position.
Rear speaker
45°
Rear speaker (L)
8
Rear speaker (R)
60 to 90cm
SONY MHC-V909AV (E) 3-860-316-11Actual page number:
Adjusting the speaker volume
To enjoy Dolby Pro Logic Surround sound, turn the Dolby Pro Logic mode on, then adjust the volume of each speaker using the test tone that the system provides.
POWER
1
1 Press PRO LOGIC (or PRO LOGIC
ON/OFF on the remote).
“PRO LOGIC ON” appears.
2 Press T.TONE ON/OFF on the
remote.
The test tone is heard from the speakers in the following order. Adjust the volume of the test tone.
Front (left) n Center n Front (right)
n
Rear
3 From your listening position, press
CENTER LEVEL +/– and REAR LEVEL +/– on the remote to adjust the volume.
The volume levels from each speaker must become the same.
4 Press T.TONE ON/OFF when you
are done adjusting.
The test tone is turned off.
Tip
If you turn VOLUME (or press VOL +/– on the remote) all the speaker volumes change.
2,4 3
1
9
SONY MHC-V909AV (E) 3-860-316-11Actual page number:
Step 3: Setting the time
You must set the time before using the timer functions.
1 3,52,4
1 Press CLOCK/TIMER SET.
The hour indication flashes.
Tips
• If you’ve made a mistake, start over from step 1.
• Setting the time deactivates the demo mode.
If you want to display the demo mode, press DISPLAY/DEMO when the power is off.
Note
When setting the time, set the equalizer display to anything other than Spectrum analyzer pattern 3. (See “To change the equalizer display” on page 54.)
2 Turn the jog dial to set the hour.
The clock is on a 12-hour system.
3 Press ENTER/NEXT.
The minute indication flashes.
4 Turn the jog dial to set the minute. 5 Press ENTER/NEXT.
The clock starts working.
10
03/04-11_MHC-V909AV.11E 98.11.9, 11:45 AM10
SONY MHC-V909AV (E) 3-860-316-11Actual page number:
Step 4: Presetting radio stations
You can preset up to 40 stations, 20 for FM, 10 for MW and 10 for SW. For 2 band models, you can preset up to 30 stations, 20 for FM and 10 for AM.
3 Turn the jog dial.
The frequency indication changes and scanning stops when the system tunes in a station. “TUNED” and “STEREO” (for stereo programs) appear.
AUTO
TUNED STEREO
MHz
VOLUME
POWER
3,56214
1 Press TUNER/BAND repeatedly
until the band you want appears in the display.
Each time you press this button, the band changes as follows:
2 band model: FM ˜ AM 3 band model: FM n MW n SW
n
2 Press TUNING MODE repeatedly to
select “AUTO.”
4 Press TUNER MEMORY.
A preset number appears in the display.
Preset number
TUNED STEREO
AUTO
VOLUME
5 Turn the jog dial to select the preset
number you want.
6 Press ENTER/NEXT.
The station is stored.
7 Repeat steps 1 to 6 to store other
stations.
To tune in a station with a weak signal
Press TUNING MODE repeatedly to select “MANUAL” in step 2, then turn the jog dial to tune in the station.
To change the preset number
Start over from step 1.
To change the AM tuning interval
The AM tuning interval is factory-preset to 9 kHz. To change the AM tuning interval, tune in any AM station first, then turn off the power. While holding down the ENTER/NEXT button, turn the power back on. When you change the interval, AM preset stations will be erased. To reset the interval, repeat the same procedure.
Tip
The preset stations are retained for half a day even if you unplug the power cord or a power failure occurs.
03/04-11_MHC-V909AV.11E 98.11.9, 11:45 AM11
11
SONY MHC-V909AV (E) 3-860-316-11Actual page number:
Connecting optional AV components
To enhance your system, you can connect optional components. Refer to the instructions of each component.
Connecting audio components
Select one of the following two connections, depending on the equipment to be connected and method of connecting.
Connecting an MD deck for digital recording
You can record from a CD to an MD deck digitally by connecting an optical cable.
To the DIGITAL IN jack of the MD deck
Connecting an MD deck for analog recording
Be sure to match the color of the plugs and the connectors. To listen to the sound of the connected MD deck, press FUNCTION repeatedly until “MD” appears.
To the audio outputs of the MD deck
Note
If you cannot select “MD” by pressing FUNCTION, press POWER while pressing FUNCTION when the power is turned off. “VIDEO” will be switched to “MD.” To return to “VIDEO,” do the same procedure.
To the audio inputs of the MD deck
Note
You cannot record from a VIDEO CD to an MD deck digitally. When you record from a VIDEO CD to an MD deck, connect an optional audio cable to the audio output. (See “Connecting an MD deck for analog recording.”)
12
04/12-14_MHC-V909AV.11E 98.11.9, 11:45 AM12
Tip
If you connect a turntable with an MM cartridge, connect it to VIDEO/MD IN using the optional MM cartridge equalizer and an audio connecting cord. To listen to the sound, press FUNCTION repeatedly until “VIDEO” or “MD” appears.
SONY MHC-V909AV (E) 3-860-316-11Actual page number:
Connecting a super woofer speaker
You can connect an optional super woofer speaker.
Connecting a VCR
Be sure to match the color of the plugs and the connectors. To listen to the sound of the connected VCR, press FUNCTION repeatedly until “VIDEO” appears.
By connecting the audio output jacks of your VCR to the VIDEO/MD (AUDIO) IN jacks using an optional audio cable, you can enjoy video playback in powerful stereo sound.
Moreover, if you connect the video input on the VCR to the VIDEO/MD (AUDIO) OUT jacks and VIDEO OUT (or S VIDEO OUT) jack using the supplied video connecting cable (or an optional S VIDEO connecting cable), you can record the audio and video signals from a VIDEO CD onto video tape.
To super woofer
To the audio outputs of the VCR using an optional audio cable
To the audio inputs of the VCR using an optional audio cable
Note
If the sound is distorted when selecting “VIDEO,” switch to “MD” (see “Note” on page 12).
To the S VIDEO input of the VCR using an optional S VIDEO cable
To the video input of the VCR using a video cable
04/12-14_MHC-V909AV.11E 98.11.9, 11:45 AM13
13
SONY MHC-V909AV (E) 3-860-316-11Actual page number:
Connecting outdoor antennas
Connect the outdoor antenna to improve the reception.
FM antenna
Connect an optional FM outdoor antenna. You can also use the TV antenna instead.
Screw clamp
75-ohm coaxial cable (not supplied)
FM75
y
AM
Ground wire (not supplied)
AM antenna
Connect a 6 to 15 meter (20 to 50 feet) insulated wire to the AM antenna terminal. Leave the supplied AM loop antenna connected.
Insulated wire (not supplied)
Screw clamp
Ground wire (not supplied)
Important
If you connect an outdoor antenna, ground from y terminal with the screw clamp. To prevent a gas explosion, do not connect the ground wire to a gas pipe.
14
04/12-14_MHC-V909AV.11E 98.11.9, 11:45 AM14
FM75
AM
y
SONY MHC-V909AV (E) 3-860-316-11Actual page number:
Basic Operations
·∏
§
π
0)
+=
Playing a VIDEO CD
You can play both VIDEO CDs without PBC functions (Ver 1.1) and VIDEO CDs with PBC functions (Ver 2.0).
You can enjoy two kinds of playback according to the disc type.
POWER
DISC SKIP EX-CHANGE
0/)
3
1/ALL DISCS
p
jog dial
2
VOLUME
·∏
1 Turn on your TV and select the
video input.
Refer to the operating instructions supplied with your TV if you need help.
2 Press § OPEN/CLOSE and place
up to two VIDEO CDs on the disc tray.
If a disc is not placed properly, it will not be recognized.
With the label side up. When you play a VIDEO CD single, place it on the inner circle of the tray.
To insert a third disc, press DISC SKIP EX-CHANGE to rotate the disc tray.
3 Press one of the DISC 1~3 buttons.
The disc tray closes and playback starts. If you press ·∏ (or SELECT CD ( on the remote) when the disc tray is closed, playback starts from the CD whose button is lit green.
Disc tray number Playing time
Basic Operations
SELECT CD (
PREV– / NEXT+
05/15-28_MHC-V909AV.11E 98.11.9, 11:46 AM15
TV POWER TV VOL +/– TV CH +/–
D.SKIP
P
p 0/)
VOL +/–
ALL1DISCS
Track number
VOLUME
continued
15
SONY MHC-V909AV (E) 3-860-316-11Actual page number:
Playing a VIDEO CD (continued)
To Do this
Stop playback Press p. Pause Press ·∏ (or P on the
Resume playbackPress ·∏ (or SELECT CD (
Select a track or Press NEXT+ to go foward, or scene PREV– to go back.
Find a point in a Press and hold 0 or ) track or scene*2during playback, and release
Select a CD Press one of DISC 1~3 button. in stop mode Or press DISC SKIP EX-
Play only the Press 1/ALL DISCS repeatedly VIDEO CD you until “1 DISC” appears. have selected
Play all VIDEO Press 1/ALL DISCS repeatedly
3
CDs* Remove or Press § OPEN/CLOSE.
change the VIDEO CDs
Adjust the Turn VOLUME (or press volume VOL +/– on the remote.
remote)*1.
on the remote).
Or during playback or pause, turn the jog dial clockwise (to go forward) or counterclockwise (to go back) and release it when you reach the desired track*2.
at the desired point.
CHANGE (or D. SKIP on the remote).
until “ALL DISCS” appears.
Tips
• Pressing ·∏ when the power is off
automatically turns the power on and starts VIDEO CD playback if there is a VIDEO CD in the tray (One Touch Play).
• You can switch from another source to the VIDEO
CD player and start playing a VIDEO CD just by pressing ·∏ or the DISC 1~3 buttons (Automatic Source Selection).
• If there is no VIDEO CD in the player,
“CD NO DISC” appears in the display.
• When a disc is selected or the VIDEO CD placed
in that position is playing, the DISC 1~3 button for that position lights green.
*1There may be some disturbance in the video
image.
2
*
Only for VIDEO CDs without PBC functions (Ver
1.1).
3
*
This function cannot be used during menu playback of a VIDEO CD with the PBC functions (Ver 2.0).
16
05/15-28_MHC-V909AV.11E 98.11.9, 11:46 AM16
SONY MHC-V909AV (E) 3-860-316-11Actual page number:
Playing a CD
·∏
§
π
0)
+=
— Normal Play
You can play up to three CDs in a row.
1
POWER
0/)
2
p
·∏
1 Press § OPEN/CLOSE and place
up to two CDs on the disc tray.
If a disc is not placed properly it will not be recognized.
With the label side up. When you play a single CD, place it on the inner circle of the tray.
To insert a third disc, press DISC SKIP EX-CHANGE to rotate the disc tray.
2 Press one of the DISC 1~3 buttons.
The disc tray closes and playback starts. If you press ·∏ (or SELECT CD ( on
the remote) when the disc tray is closed, playback starts from the CD loaded on the tray whose button is lit green.
Disc tray number
Playing time
Basic Operations
EX-CHANGE
SELECT CD (
=/+
1/ALL DISCS
jog dialDISC SKIP
VOLUME
D.SKIP
P
p 0/)
VOL +/–
ALL1DISCS
Track number
VOLUME
continued
17
05/15-28_MHC-V909AV.11E 98.11.9, 11:46 AM17
SONY MHC-V909AV (E) 3-860-316-11Actual page number:
Playing a CD (continued)
Recording a CD/VIDEO
To Do this
Stop playback Press p. Pause Press ·∏ (or P on the
remote). Press again to resume play.
Select a track During playback or pause,
turn the jog dial clockwise (to go forward) or counterclockwise (to go back) and release it when you reach the desired track. Or press + (to go forward) or = (to go back) on the remote.
Find a point in Press and hold down ) or a track 0 during playback and
release it at the desired point.
Select a CD Press a DISC 1~3 button or in stop mode DISC SKIP EX-CHANGE (or
D. SKIP on the remote).
Play only the Press 1/ALL DISCS CD you have repeatedly until “1 DISC” selected appears.
Play all CDs Press 1/ALL DISCS repeatedly
until “ALL DISCS” appears. Remove the CD Press § OPEN/CLOSE. Exchange other Press DISC SKIP
CDs while EX-CHANGE (or D. SKIP on playing the remote).
Adjust the Turn VOLUME (or press volume VOL +/– on the remote).
CD
— CD Synchro Recording
The CD SYNCHRO button lets you record audio sources from a CD/VIDEO CD to a tape easily. You can use TYPE I (normal) or TYPE II (CrO2) tapes.
DISC SKIP
POWER
EX-CHANGE
4
2
π
53
1
Tips
• Pressing ·∏ when the power is off
automatically turns the power on and starts CD playback if there is a CD in the tray (One Touch Play).
• You can switch from another source to the CD
player and start playing a CD just by pressing
·∏ or the DISC 1~3 buttons (Automatic Source Selection).
• If there is no CD in the player, “CD NO DISC”
appears in the display.
• When a disc tray is selected or the CD placed on
that tray is playing, the DISC 1~3 button for the respective tray lights green.
18
05/15-28_MHC-V909AV.11E 98.11.9, 11:46 AM18
DOLBY NR
SONY MHC-V909AV (E) 3-860-316-11Actual page number:
1 Press § and insert a blank tape into
deck B.
With the side you want to record facing forward.
‚º
π
ª·
§
2 Press § OPEN/CLOSE and place a
CD.
Then press again to close the disc tray. If the indicator for the tray you want to
record is not lit green, press DISC SKIP EX-CHANGE repeatedly so that it lights green.
+=
With the label side up. When you play a single CD, place it on the inner circle of the tray.
0)
π
·∏
§
To stop recording
Press π on deck B or p on the CD player.
Tips
• If you want to record from the reverse side, press ª so that ª (for reverse side) lights up.
• When you record on both sides, be sure to start from the front side. If you start from the reverse side, recording stops at the end of the reverse side.
• When you want to reduce the hiss noise in low­level high-frequency signals, press DOLBY NR on the remote so that “DOLBY NR B” appears after pressing CD SYNCHRO.
Notes
• You cannot listen to other sources while recording.
• You cannot record from a VIDEO CD with PBC functions (Ver 2.0).
Basic Operations
3 Press CD SYNCHRO.
Deck B stands by for recording and the CD player stands by for playback. · (for front side) lights up.
4 Press DIRECTION repeatedly to
select A to record on one side. Select a (or RELAY) to record on both sides.
5 Press ∏ PAUSE on deck B.
Recording starts.
05/15-28_MHC-V909AV.11E 98.11.9, 11:46 AM19
19
SONY MHC-V909AV (E) 3-860-316-11Actual page number:
Listening to the radio
–– Preset Tuning
Preset radio stations in the tuner's memory first (see “Step 4: Presetting radio stations”).
3
POWER
VOLUME
STEREO / MONO
POWER
1 Press TUNER/BAND repeatedly
until the band you want appears in the display.
Every time you press the button, the band changes as follows:
2 band model: FM ˜ AM 3 band model: FM n MW n SW
n
2 Press TUNING MODE repeatedly
so “PRESET” appears in the display.
MANUAL n AUTO n PRESET
n
3 Turn the jog dial (or press = or
+ on the remote) to tune in the
desired preset station.
Turn counterclockwise (or press = on the remote) for lower preset numbers.
12
Preset number Frequency
PRESET
Turn clockwise (or press +
+–
on the remote) for higher preset numbers.
TUNED STEREO
MHz
VOLUME
20
05/15-28_MHC-V909AV.11E 98.11.9, 11:46 AM20
TUNER/ BAND
=/+
VOL +/–
To Do this
Turn off the radio Press POWER. Adjust the volume Turn VOLUME (or press
VOL +/– on the remote).
SONY MHC-V909AV (E) 3-860-316-11Actual page number:
To listen to non-preset radio stations
Press TUNING MODE repeatedly so that “MANUAL” appears in step 2, then tune in the station by turning the jog dial.
Tips
• Pressing TUNER/BAND when the power is off automatically turns the power on and tunes to the last received station (One Touch Play).
• You can switch from another source to the radio just by pressing TUNER/BAND (Automatic Source Selection).
• If an FM program is noisy, press STEREO/MONO so that “MONO” appears in the display. There will be no stereo effect, but the reception will improve. Press the button again to restore the stereo effect.
• To improve broadcast reception, reorient the supplied antennas.
Basic Operations
05/15-28_MHC-V909AV.11E 98.11.9, 11:46 AM21
21
SONY MHC-V909AV (E) 3-860-316-11Actual page number:
Loading...
+ 47 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use