Sony KP-53S55, KP-46S55 Owner’s Manual

SONY

3-754-298-22 (1)

Color Rear Video

Projector

Operating Instructions

KP-46S55

KP-53555

@1994 by Sony Corporation

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

RISK OF ELECIRIC SHOCK

DO NOT OPEN

Note on Closed Caption

This television receiver provides display of televisio,_ closed captioning in accordance with §15.119 of the

FCC rules.

Note on CATV system installer

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as

close to the point of cable entry as practical.

Use of this television receiver for other than private viewing of programs broadcast on UHF or VHF or

transmitted by cable companies for the use of the general public may require authorization from the broadcaster/cable company and/or program owner.

CAUTION: TO REDUCE THE RISK OF ELI-C-IRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO OUALIFIED SERVICE PERSONNEL.

I ills _ymbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the

presence of important operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

CAUTION

TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS

POLARIZED AC PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

Note on convergence adjustment

Before you use your projection TV, make sure to adjust convergence. For the procedure, see page 10.

Note on cleaning

Clean the cabinet of the projection TV with a dry soft cloth. To remove dust from the screen, wipe it gently

with a soft cloth using vertical strokes only. Stubborn

stains may be removed with a cloth slightly dampened with a mild detergent solution. Never use strong

solvents such as thinner or benzine for cleaning. If the picture becomes dark after using the projection TV for a long period of time, it may be necessary to clean the inside of the projection TV. Consult qualified

service personnel.

Owner's Record

The model and serial numbers are located at the rear ot

the projection TV. Record these numbers in the spaces provided below. Refer to them whenever you call upon your Sony dealer regarding this product.

Model No.

Serial No.

CAUTION

When using TV games, computers, and similar products with your projection TV, keep the brightness and contrast functions at low settings. If a fixed (non- moving) pattern is left on the screen for long periods of time at a high brightness or contrast setting, the image

can be permanently imprintd onto the screen. These types of imprints are not covered by your warranty

because they are the result of misuse.

4 Welcome! 4 Precautions

fl II

Getting Started

5 Step 1: Installing the projection TV 6 Step 2: Connections

10 Step 3: Setting up the remote commander 10 Step 4: Adjusting convergence (CONVERGENCE) 11 Step 5: Setting cable TV on or off 12 Step 6: Presetting channels 14 Changing the menu language

Operations

15 Watching TV programs 16 Watching two programs at one time -PIP 18 Selecting picture and sound effects (PROGRAM

PALETTE)

19 Adjusting the picture (VIDEO) 20 Adjusting the color temperature (TRINITONE)

20 Reducing picture noise (NR) 21 Adjusting sound (AUDIO) 22 Listening to surround sound (SURROUND) 22 Selecting stereo or bilingual programs (MTS) 23 Setting the speaker switch (SPEAKER) 23 Displaying closed caption 24 Setting daylight saving time (DAYLIGHT SAVING) 25 Setting the clock (CURRENT TIME SET) 26 Turning the projection TV on and off automatically

(ON/OFF TIMER)

27 Blocking a TV program from appearing on the

screen (CHANNEL BLOCK)

28 Customizing channel names (CHCAPTION) 29 Setting video labels (VIDEOLABEL) 30 Selecting your favorite channels (FAVORITE

CHANNEL)

31 Operating video equipment 33 Operating a cable box

Additional Information

34 Troubleshooting 35 Specifications

Back cover Index

The captions inparentheses indicate menu names.

Fhank you for purchasing the Sony Color Rear Video Projection TV. Here are some of the features you will enjoy with your projection TV:

This pl'ojection 'IV operates on extremely high voltage. To prevent fire or electric shock, please follow the precautions below.

• On Screen menus that let you set the picture quality,

sound, and other settings

• Picture-in-Picture that allows you to watch another TV

channel, video or cable image as a window picture

• On/off timer that allows you to make the TV program of your choice be displayed on the screen for a

specified duration

• Dynamic Focus circuitry that automatically focuses the scanning electron beam for enhanced sharpness, especially at the comers

• Universal remote commander supplied that allows you to operate Sony and other manufacturers' video equipment

About this manual

The instructions in this manual are for two models.

There are no differences between these models in

operation. The differences in specifications are indicated in the text.

Instructions in this manual are based on use of the remote commander. You can also use the controls on

the projection TV if they have the same name as those on the remote commander.

Safety

• Operate the projection TV only on 120 V AC.

• One blade of the plug is wider than the other for safety purposes and will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, contact your dealer.

• Should any liquid or solid object fall into the cabinet, unplug the projection TV and have it checked by

qualified personnel before operating it further.

• Unplug the projection TV from the wall outlet if you are not going to use it for several days or more. To

disconnect the cord, pull it out by the plug. Never pull the cord itself.

For details concerning safety precautions, see the supplied leaflet"IMPORTANT SAFEGUARDS."

Installing

• To prevent internal heat build-up, do not block the

ventilation openings.

• Do not install the projection TV in a hot or humid

place, or in a place subject to excessive dust or mechanical vibration.

• Avoid operating the projection TV at temperatures below 5°C (41°F).

• If the projection TV is transported directly from a cold to a warm location, or if the room temperature has changed suddenly, the picture may be blurred or show poor color. This is because moisture has condensed on the mirror or lenses inside. If this happens, let the moisture evaporate before using the projection TV.

• To obtain the best picture, do not expose the screen to direct illumination or direct sunlight. It is recommended to use spot lighting directed down from the ceiling or to cover the windows that face the screen

with opaque drapery. It is desirable to install the projection TV in a room where the floor and walls are not of reflecting material. If necessary, cover them with

dark carpeting or wall paper.

Getting Started

For the best picture quality, install the projection TV within the areas shown below.

Optimum viewing area (Horizontal)

Preparing for your projection TV

Before you use your projection TV, adjust convergence. For the procedure, see "Step 4: Adjusting convergence (CONVERGENCE)" on page 10.

Optimum viewing area (Vertical)

Getting Started I S

Although you can use either an indoor antenna or outdoor antenna with your projection TV, we

recommend connecting to an outdoor antenna or a cable TV system for improved picture quality.

To an antenna

Connect your antenna cable to the VHF/UHF antenna

terminal. If you cannot connect your antenna cable directry to the terminal, follow one of the instructions

below depending on your cable type.

Connecting an antenna/cable TV system without a VCR

To cable or antenna

(Rear of projection TV)

Cable

To cable box

If your cable company requires you to connect a cable box, make the connection as follows:

Cable box

VHF/UHF

(Rear of projection W)

VHF/UHF

A (Rear of projection W)

• VHF only 75-ohm coaxial cable

• VHF/UHF

• Cable

• VHF only 300-ohm twin lead cable

• UHF only I

• VHF/UHF Antenna connector

• VHF J_

and __D_ HF

• UHF [

Notes

• Most VHF/UHF combination antennas have a signal splitter. Remove the splitter before attaching the appropriate connector.

• If you use the U/V mixer, snow and noise may appear in the picture when viewing cable TV channels over 37(W+1).

75-ohm coaxial cable

300-ohm twin lead cable

(Rear of projection "IV)

(Rear of projection TV)

EAC-66 U/V mixer

(not supplied)

VHF/UHF

6 IGetting Started

Connecting an antenna/cable TV system with a VCR

For details on connection, see the instruction manual of your VCR. Before connecting, disconnect the AC

power cords of the equipment to be connected.

After making these connections, you will be able to do the following:

• View the playback of video tapes

• Record one TV program while viewing another program

• Watch two TV programs at one time using a window picture (Picture-in-Picture)

To a conventional VCR

Without a cable box

(Rear of projection TV)

AVuIDIEoO(L_e/IhOWel-'_h_F_ _

AUDIO-R(red) -_ VMC-810S/820S (not supplied)

Note

• To connect a monaural VCR, connect the audio output of the VCR to AUDIO-L (mono) of VIDEO 1/2 IN on the projection TV.

With a cable box

(Rear of projection TV) _L!_OUT 112___

-- VHF/UHF output

I AUDIO VIDEO

B m

_ VHF/UHF output

OOT I

OUT LINE

VCR

Video and audio outputs

IN _ [_ Antenna _able

VHF/UHF input

Cable box

Cable

I AUDIO VIDEO OUT_! I

_L__NT E IN _ VHF/UHF input

AUDIO-L(white) _ I_

VlDEO(yellow)___ h h _ _ _ VCR

AUDIO-R(red) ----_ _ Video and audio outputs

VMC-810S/820S (not supplied) T

Getting Started I 7

To an S video equipped VCR

If your VCR has an S video output jack, make the connection as follows and then set S-VIDEO to ON on

your projection TV. It is set to ON at the factory.

Without a cable box

(Rear of projection "IV) _ J

sVIDEO

AUDIO L (white)_-_

AUDIO R (red)_

Note

• Video signals are composed of Y (luminance) and C (chroma)

signals. The S connection sends the two signals separately preventing degradation, and gives better picture quality

compared to conventional connection.

RK-74A (not supplied)

YC-15V/30V (not supplied)

_ VHF/UHF output

AUDIO VIDEO S VIDEO ouTi_ ILINE l_=_ _ Antenna cable

VCR

P' outputs output

l iAudio I Svideo

With a cable box

(Rear of projection TV)

SV,DEO-- &

AUDIO L (white) _

AUDIO R (red)_

RK-74A (not supplied) J

YC-15V/30V (not supplied)

Setting S video on or off

1 Press MENU.

2 Press + Z_or - _7to select MODE SET and

press RETURN.

VHF/UHF output_ _[_

• I AUDIO VIDEO S VIDEO OUT_I I __NTE IN _ VHF/UHFinput

V_ _Audi°IOutputs

VCR

Svideo output

3 Make sure the cursor (1_) is beside S-VIDEO

and press RETURN.

If the cursor is not beside S-VIDEO, press + ZXor

- V to move the cursor and press RETURN.

Cable box

Notes

• If S VIDEO appears in black, set a video input to VIDEO 1.

• If you set S VIDEO to ON, the TV automatically receive S

video signals whenever a VCR with S video is connected.

8 JGetting Started

4 Press + _ or - _7to select ON or OFF and

press RETURN,

Connecting a camcorder

This connection is convenient for watching the picture from a camcorder.

(Front of projection TV)

=o-i@ oo,o.ro0,

-- AUDIO L(white)

VMC-810SI820S (not supplied)

Note

• To connect a monaural camcorder, connect the audio output of the camcorder to AUDIO-L (mono) of VIDEO 3 IN on the

projection TV.

Connecting an audio system

When connecting audio equipment, see page 23 for

more information.

Audio and video outputs

(Rear of projection TV)

____,_ RK-74A (not supplied)

Note

• You can adjust the bass, treble and balance, or select surround or an MTS (Multichannel TV Sound) mode with the supplied

remote commander.

AUDIO OUT L(white)

Set the amplifier's function to line input.

AUDIO OUT R(red) L

_ Line input _ _l_

iI i

Stereo amplifier

Getting Started j 9

Insert one size AA (R6) battery (supplied) by matching the + and - on the battery to the diagram inside the

battery compartment.

rl'he projection tube image appears on the screen in

three layers (red, green and blue). If they do not

converge, the color is poor and the picture blurs. To correct this, adjust convergence.

POWER

Notes

• With normal use, the battery should last for approximately six

months.

• If you do not use the remote commander for an extended

period of time, remove the battery to avoid possible damage from battery leakage.

• Do not handle the remote commander roughly. Do not drop it, step on it or let it get wet.

• Do not place the remote commander in direct sunlight, near a heater, or where the humidity is high.

RETURN

Press POWER to turn on the projection TV.

The TIMER/STAND BY indicator flashes until the picture appears.

POWER

Press MENU.

The main menu appears.

_[_PROG PALETTE

[_MODE SET

TIME

_SET UP [_]3ENGLISH

r_CONVERGENCE

SELECT _ RETURN EXIT_

Press + _ or - V to move the cursor (1_) to CONVERGENCE and press RETURN.

The CONVERGENCE adjustment screen appears.

10 IGettingStarted

RETURN

J 1_3CONVERGENCE

R G

B B

_LECT _ RETLk_J EXJT J_

R=Red G=Green

B=Blue

"_1

Press + _ or - _7to move the cursor (1_) to

the symbol showing the line you want to

adjust, and press RETURN.

RETURN

I'_'ICONVERGENCE

SELEC1 _ RETUI3N EXI T

I: Red vertical line (left/right adjustment)

--: Red horizontalline (up/down adjustment)

I: Blue vertical line (left/right adjustment)

--: Blue horizontalline (up/down adjustment)

Press + _ or - _7to move the line until it converges with the center green line, and

press RETURN.

RETURN

To move up/right, press + A. To move down/left, press - V.

._ONVERGENCE

G , __1

B 5 _ B

G+R ,T_

_1 _1

If you have connected the projection TV to a cable TV system, you should set the cable connection on or off. Set CABLE to ON, the factory setting, to preset or

watch cable TV channels. Set to OFF to preset or watch VHF/UHF channels.

_MENU

RETURN

1 Press MENU.

The main menu appears.

6 Repeat steps 4 and 5 to adjust the other

lines until all three lines converge and are seen as a white cross.

I_ICON VE R,__

-- -- "_1

SEL[CT _ RET_ EXIT_ |

white cross

7 Press MENU to return to the original screen.

Note

• If more than 90 seconds elapse after you press a button, the menu disappears automatically.

Press + _ or - _7 to move the cursor (1_) to

,[_]PROG PALETTE

[Z_MODE SET

£_SET UP []ENGLISH [iJCONVERGENCE

SELECT_ RET_N EXIT

SET UP and press RETURN.

The SET UP menu appears.

RETURN

,CABLE: ON

AUTO PROGRAM

CH ERASE/ADD CH CAPTION

VIDEO LABEL FAVORITE CHANNEL

_MENU

TIME

Getting Started I 11

+ 25 hidden pages