Sony DSR-370L, DSR-370K2, DSR-370K1, DSR-370PK1, DSR-370PK2 User Manual

...

3-206-360-12(1)

Digital Camcorder

Operating Instructions

Before operating the unit, please read this manual thoroughly and retain it for future reference.

Note

The supplied CD-ROM includes operation manuals for the DSR-370/570WS series of digital camcorders (English, Japanese, French, German, Italian and Spanish versions). For more details, see page 14 “Using the CD-ROM Manual.”

DSR-370L/370PL DSR-370K1/370PK1 DSR-370K2/370PK2 DSR-570WSL/570WSPL

 2001 Sony Corporation

Owner’s Record

VAROITUS

The model and serial numbers are located on the top. Record these numbers in the spaces provided below. Refer to them whenever you call upon your Sony dealer regarding this product.

Model No.

Serial No.

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

Paristo voi räjähtää jos se on virheellisesti

asennettu.

Vaihda paristo ainoastaan laitevalmistajan

suosittelemaan tyyppiin.

Hävitä käytetty paristo valmistajan ohjeiden

mukaisesti.

For customers in the USA

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

The shielded interface cable recommended in this manual must be used with this equipment in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.

ADVARSEL!

Lithiumbatteri-Eksplosionsfare ved fejlagtig

håndtering.

Udskiftning må kun ske med batteri

af samme fabrikat og type.

Levér det brugte batteri tilbage til leverandøren.

ADVARSEL

Lithiumbatteri - Eksplosjonsfare.

Ved utskifting benyttes kun batteri som

anbefalt av apparatfabrikanten.

Brukt batteri returneres

apparatleverandøren.

VARNING

Explosionsfara vid felaktigt batteribyte.

Använd samma batterityp eller en likvärdig typ

som rekommenderas av apparattillverkaren.

Kassera använt batteri enligt gällande

föreskrifter.

For the customers in Europe (DSR-370PL/370PKI/ 370PK2/570WSPL only)

This product with the CE marking complies with the EMC Directive (89/336/EEC) issued by the Commission of the European Community. Compliance with this directive implies conformity to the following European standards:

• EN55103-1: Electromagnetic Interference (Emission)

• EN55103-2: Electromagnetic Susceptibility (Immunity) This product is intended for use in the following Electromagnetic Environment(s): E1 (residential), E2 (commercial and light industrial), E3 (urban outdoors) and E4 (controlled EMC environment, ex. TV studio).

Note about laser beams

Laser beams can damage the CCDs of this camcorder. In environments where laser beams are used, be careful to prevent the laser beams from striking the surfaces of the CCDs.

Chapter 1

Overview

Product Configurations ....................................................9

Features ........................................................................... 10

Features of the DSR-370/370P/570WS/570WSP Camera

Section .......................................................................... 10

Features of the DSR-570WS/570WSP Camera Section ... 12

Features of VCR Section ................................................... 12

Other Features ................................................................... 13

Using the CD-ROM Manual............................................. 14

CD-ROM System Requirements ....................................... 14

Preparations ....................................................................... 14

To Read the CD-ROM Manual.......................................... 14

Location and Function of Parts ..................................... 15

Front View ......................................................................... 15

Right Side View ................................................................. 16

Left and Upper View ......................................................... 26

Rear and Bottom................................................................ 28

VCL-716BX Zoom Lens (for DSR-370K2/370PK2) ....... 30

Chapter 2

Fitting and Connections

VCL-719BX Zoom Lens (for DSR-370K1/370PK1) ....... 32

DXF-801/801CE Viewfinder............................................. 35

Inserting and Replacing the Lithium Battery ............... 37

Fitting the Lens ............................................................... 39

Using Accessories .......................................................... 41

Using the Viewfinder ......................................................... 41

Fitting the 5-inch Electronic Viewfinder ........................... 42

Fitting to a Tripod.............................................................. 42

Using an Optional Microphone ......................................... 43

Using a Video Light........................................................... 44

Fitting the Shoulder Strap ................................................. 45

Connecting to Audio System ............................................. 46

Connecting a CA-370 Intercom Adaptor .......................... 48

Using the Optional LC-DS500 Carrying Case .................. 49

Using the Optional LC-DS300SFT Soft Carrying Case ... 49

Table of Contents 3

Table of Contents

Chapter 2

Fitting and Connections

(Continued)

Chapter 3

Shooting

Connections .................................................................... 50

Connecting a Number of Camcorders ............................... 50

Connecting an External VCR ............................................ 51

Connecting an i.LINK Digital Cassette Recorder ............. 51

Connecting a Camera Control Unit ................................... 52

Power Supply ................................................................... 53

Using a BP-L40/L40A/L60/L60A/L90/L90A/M50/M100

Battery Pack ................................................................. 53

Using an AC Adaptor ........................................................ 55

Using the Anton Bauer Intelligent Battery System ........... 55

Basic Procedure for Shooting........................................ 57

Using DynaLatitude Function ........................................... 58

Recording ........................................................................ 59

Usable Cassettes ................................................................ 59

Recording on the Internal VCR......................................... 60

Recording External Video Signals..................................... 64

Recording on an External VCR Using the VTR/CCU

Connector (26-pin) or DV OUT Connector ................. 64

Back Space Editing ......................................................... 67

Starting Back Space Editing at Any Tape Position ........... 67

Using the Edit Search Function While Back Space

Editing .......................................................................... 68

Using the Freeze Mix Function ......................................... 69

Playback — Checking Recorded Contents ................... 70

Checking the Recorded Contents Immediately After

Shooting — Recording Review.................................... 70

Viewing Monochrome Playback in the Viewfinder........... 70

Viewing Color Playback.................................................... 70

Setting Time Values .........................................................71

Setting the User Bit Value ................................................. 72

Setting the Time Code Value ............................................. 73

Synchronization With External Time Code Signals

— Gen-Lock ................................................................ 75

4 Table of Contents

ClipLink Shooting ........................................................... 77

Setting Editing Points While Shooting.............................. 79

Resuming Recording in ClipLink Mode ........................... 81

Chapter 4

Viewfinder Screen Indications and Menus

Viewfinder Screen Indications ....................................... 85

Changing the Viewfinder Display ..................................... 85

Viewfinder Normal Indications....................................... 87

Status Indications .............................................................. 90

Viewfinder Basic Menu ...................................................92

Basic Menu Operations ..................................................... 92

Contents and Settings of Each Menu Page........................ 92

Viewfinder Advanced Menu ............................................ 98

Advanced Menu Operations .............................................. 98

Contents and Settings of Each Menu Page...................... 100

Video Output and Viewfinder Picture (DSR-570WS/

570WSP only) ............................................................ 107

Setup Files .....................................................................108

Calling up a Setup File .................................................... 108

Changing File Settings .................................................... 110

Saving File Settings......................................................... 110

Using SetupNavi and SetupLog................................... 113

Chapter 5

Adjustments and Settings

Setting Up the Camera Using Data Recorded on Tape ... 113

Recording the Menu Settings Onto a Tape ...................... 114

Viewing SetupLog Data .................................................. 115

Setting on the VCR Section — VCR Menu................... 117

VCR Menu Operation .................................................... 118

Basic Operation ............................................................... 118

Menu 101 Setting the Real Time Clock and Calendar ... 119 Menu 201 Checking the Total Operating (Power-On)

Hours .......................................................................... 119

Menu 204 Selecting Frame Mode (DF/NDF) for Time

Code (for DSR-370/570WS only).............................. 119

Menu 206 Selecting Battery Capacity Indication .......... 120

Menu 207 Setting Standby-On Period ........................... 120

Menu 210 Using Auto-Check Function .......................... 121

Menu 211 Selecting ClipLink Function ......................... 123

Menu 212 Selecting Audio Recording Mode................. 123

(Continued)

Table of Contents 5

Table of Contents

Chapter 5

Adjustments and Settings (Continued)

Menu 213 Selecting Audio Reference Level.................. 124

Menu 214 Setting Fade-In/Fade-Out for the Audio

Recording Start and Stop Points ................................ 124

Menu 220 Using Setup Add

(for DSR-370/570WS only) ....................................... 125

Menu 221 Using Setup Remove

(for DSR-370/570WS only) ....................................... 125

White Balance Adjustment ........................................... 126

Saving an Appropriate White Balance Value in

Memory ...................................................................... 126

Using the Preset White Balance Settings ........................ 127

Light Sources and Color Temperature............................. 128

Using the ATW (Auto Tracing White Balance)

Function ..................................................................... 128

Black Balance Adjustment ...........................................129

Shutter Settings ............................................................ 130

Viewfinder Screen Adjustments .................................. 132

Adjusting the Lens ........................................................ 133

Appendix

Flange Focal Length Adjustment .................................... 133

Iris Adjustments............................................................... 134

Adjusting the Iris Sensitivity ........................................... 135

Macrophotography .......................................................... 135

Settings for Special Cases ...........................................137

Skin Detail Correction..................................................... 138

Adjusting Color in the Specified Area ............................ 138

Important Notes on Operation ..................................... 139

Characteristics of CCD Sensors ...................................... 140

Cleaning the Video Heads ............................................ 141

Warning System ............................................................142

Condensation ................................................................... 143

Troubleshooting ............................................................144

Specifications ................................................................ 146

6 Table of Contents

Related Products.............................................................. 149

Appendix

(Continued)

Chart of Optional Components and Accessories ...... 151

What Is ClipLink? ..........................................................152

How ClipLink Changes Video Production Techniques ... 152

ClipLink Operation Flow ............................................... 153

Example System Configuration ...................................... 153

Data Generated When Shooting ...................................... 154

Glossary ......................................................................... 157

Table of Contents 7

Overview

Product Configurations

Chapter1

The eight models, DSR-370L/370PL, DSR-370K1/ 370PK1/, DSR-370K2/370PK2/ and DSR-570WSL/ 570WSPL, comprise both NTSC and PAL versions and the components as shown in the figure below.

DSR-370K1/370PK1/370K2/370PK2

DSR-370L/370PL/570WSL/570WSPL

Microphone

DXF-801/801CE Viewfinder

Switch guard

Shoulder strap

The operation of the basic camcorder is the same in all cases.

VCT-U14 Tripod Adaptor

VCL-716BX Zoom Lens (for DSR-370K2/370PK2)

Test chart for flange focal length adjustment

• Lens mount cap

• Binding tie

• Operating instructions

DSR-370/370P/570WS/ 570WSP Camcorder

a) Part No. A-8279-329-A (for DSR-370/570WS)

Part No. A-8326-150-A (for DSR-370P/570WSP) b) The switch guard can be removed. (See page 15.) c) Use an optional zoom lens with the DSR-570WS/570WSP.

VCL-719BX Zoom Lens (for DSR-370K1/370PK1)

Chapter 1 Overview 9

Features

The DSR-370/370P is a 4:3 standard screen type digital camcorder. The DSR-570WS/570WSP is a 16:9 wide screen type (4:3/16:9 switchable) digital camcorder.

The performance of the Camcorder CCDs is as

Chapter 1 Overview

follows.

DSR-370/370P

/2-inch IT type Power HAD CCD

The DSR-370/370P uses 1/2-inch IT type Power HAD CCDs which excel in reduction of smear, sensitivity and picture quality.

• Smear: –110 dB

• Sensitivity: F11.0 (at 3200 K, 2000 lux)

• S/N: 62 dB

DSR-570WS/570WSP

/3-inch IT type Power HAD CCD

The DSR-570WS/570WSP uses 2/3-inch IT type Power HAD CCDs with 520,000 pixels which excel in picture quality and sensitivity.

• Smear: –120 dB

• Sensitivity: F11.0 (at 3200 K, 2000 lux)

• S/N: 63 dB

Features of the DSR-370/370P/ 570WS/570WSP Camera Section

Following are common features of the DSR-370/370P and DSR-570WS/570WSP camera section.

For more information about the DSR-570WS/570WSP, see “Features of the DSR-570WS/570WSP Camera Section” on page 12.

DCC+ (dynamic contrast control plus)

Prevents white breakup when shooting a high intensity subject, and also prevents color faults in high intensity subject.

Black stretch and compress

Enables control of luminance signal levels in black areas without changing the hue.

Variety of detail corrections

• Skin detail function: this function gives a slightly softer appearance to the subject’s face. The target skin color can be automatically set.

• Black halo correction

• Red/green vertical detail correction: this function

performs vertical detail compensation for both red and green signals.

• Horizontal detail frequency control

New Functions boost operability

EZ (easy) mode function

When there isn’t time to check the camcorder settings, simply press the EZ mode button to start the auto adjustment function using standard settings. There is no need to lose a shot for lack of setup time.

EZ (easy) focus

Press the EZ focus button before shooting to ensure a quick and accurate focus.

Dual pixel readout (DPR

When the gain is set to either 18 dB or 24 dB, the gain setting can be doubled (6 dB up) without increasing the noise level.

)

Sophisticated image processing

TruEye™ processing makes the following performance features possible. This digital signal processing has brought reproduction of natural colors to the level achieved by the human eye.

DynaLatitude™

Enables detailed adjustment of contrast control in each pixel in accordance with a histogram of luminance signal levels (see page 58).

..........................................................................................................................................................................................................

1) DPR = Dual Pixel Readout

Programmable gain

The amount of gain relative to the GAIN switch setting (H, M, or L) can be programmed as –3 dB, 0 dB, 3 dB, 6 dB, 9 dB, 12 dB, 18 dB, 18 dB+DPR, 24 dB, 24 dB+DPR and hyper gain.

Hyper gain

Hyper gain (36 dB , or about 60 times greater than 0 dB (about 120 times greater for DSR-570WS/570WSP only)) can be easily set via one switch setting. This can also be done from remote equipment.

10 Chapter 1 Overview

Auto tracing white balance (ATW)

This function automatically traces the white balance, which constantly changes as lighting conditions change. Auto tracing white balance is especially useful when there is no time to manually adjust the white balance or when shooting moves between indoor and outdoor locations.

Total level control system (TLCS)

Even if the incoming light exceeds the range in which the standard auto iris can control exposure, the auto gain control (AGC) or auto exposure (AE) backs up to ensure proper exposure.

Recording time (REC TIME) display

Recording time can be displayed in either of the following modes.

• Total recording time for all cuts (TTL

• Total recording time for current cut (DUR

)

Viewfinder super detail

Video signals for the viewfinder are mixed with DTL signals to make focusing easier.

Dual zebra pattern display

Two types of zebra patterns, zebra 1 and zebra 2 can be displayed simultaneously or independently. The zebra 1 can be set to the levels ranging from 70 to 90 IRE on the DSR-370/570WS (or from 70 to 90% on the DSR-370/570WSP) and the zebra 2 indicates the levels of 100 IRE or more for the DSR-370/570WS (or the levels of 100% or more for the DSR-370/ 570WSP).

Color temperature display

When reading the white balance, the color temperature is displayed on the viewfinder screen.

Switching the color temperatures for the preset white balance

You can select the preset white balance at 3200 K or 5600 K by setting the FILTER control. The preset white balance can be switched to other value when the menu setting is changed (see page 93).

1-kHz reference signal output

Along with a color bar, a 1-kHz reference signal can also be output.

Freeze mix function

The freeze mix function superimposes any previously recorded still picture on the viewfinder screen to facilitate framing the subject when reshooting the scene.

Edit Search Function

Pressing the EDIT SEARCH buttons allows the tape to play back in search mode. Set either of two playback speeds.

SetupLog

function

Settings at shooting are recorded onto the tape in real time. This recorded data can then be used to reproduce the same shooting conditions in subsequent shots. It also makes it easier to identify the cause of problems in previous shots.

Video light control

A video light connector and control switch are equipped. You can turn the light on and off automatically as you start and stop the VCR operation.

High-performance viewfinder (DXF-801/ 801CE)

• High resolution (600 TV lines of horizontal resolution)

• DISPLAY switch that can turn the character display on and off

• Light that can light the lens control elements

• Large-diameter eye cup for easier viewing and

focusing

• PEAKING potentiometer for vertical and horizontal detail control

• Two indicators can be used as TALLY indicators

• Tough die-cast aluminum body

• Automatic aspect ratio switching between 16:9 and

4:3 (DSR-570WS/570WSP only)

Chapter 1 Overview

Video monitor output with text

The video signal with text superimposed that is shown in the viewfinder can also be output to an external video monitor.

1) TTL = Total 2) DUR = Duration

Chapter 1 Overview 11

Features

Features of the DSR-570WS/ 570WSP Camera Section

Following are features of the DSR-570WS/570WSP,

Chapter 1 Overview

considered only as a 16:9 wide screen type camcorder. For features which are common with the DSR-370/ 370P 4:3 standard screen type camcorder, see “Features of the DSR-370/370P/570WS/570WSP Camera Section” on the previous page.

Switchable between aspect ratios 16:9 and 4:3

Menu operations allows instantaneous switching between 16:9 (wide screen) and 4:3 (standard screen) aspect ratios. In 4:3 mode, 16:9 video signals produced by wide aspect CCDs are digitally processed to extract the section corresponding to a 4:3 screen (see page

105).

Addition of aspect ID signal

By menu settings, a wide-aspect ID signal added to video signals

Automatic switching of viewfinder aspect ratio

When the supplied DXF-801/801CE viewfinder is used, the scan size of the viewfinder screen switches automatically to match the current aspect ratio (16:9 or 4:3) (see page 105).

in 16:9 mode (see page 105).

can be

DVCAM cassettes

• This camcorder can use both standard-size and minisize DVCAM cassettes. According to cassette size, the camcorder automatically corrects reel position.

• The maximum recording/playback times are 184 minutes for standard size cassettes and 40 minutes for mini cassettes.

• DVCAM cassettes include a cassette memory. Information about the editing points (ClipLink™ log data) that is specified while shooting is recorded into this cassette memory.

Able to record the external video signals

Fitting the optional DSBK-501/501P Analog Composite Input Board enables the camcorder to record external analog video signals. (See pages 27, 64

and 93.)

ClipLink™ function

The ClipLink function links all stages from shooting to editing. Once editing points have been set with this function during shooting, they can be used to boost the efficiency of editing work.

Features of VCR Section

Creation of clips

Using the ClipLink function, the camcorder operator

Features of the VCR section are common to the DSR370/370P and DSR-570WS/570WSP. The camcorder uses the DVCAM recording format. The internal signal processing is digitalized to provide more stable output signals and higher reliability.

can create clips to be used during editing. The images captured at the Mark IN points are recorded in a compressed format onto the tape as

“Index Pictures”

. In addition, editing point-related data (scene number, time code for Mark IN/OUT points, etc.) is recorded in the cassette memory.

Compatible with consumer DV

ClipLink mode

To use the ClipLink function, select the menu setting

A DV cassette recorded on a DV-format VCR can be played back on the camcorder. (Cassettes recorded in LP mode cannot be played back.)

1) ID signals complying with EIAJ CPR-1204 (DSR-370/ 570WS) or complying with ETS WSS (DSR-370P/ 570WSP).

2) Video signals refer to the following:

• Video signals output from the VIDEO OUT connector

and MONITOR OUT connector.

to set the camcorder into ClipLink mode. There is also a ClipLink continue function that enables clips to be continued even after a break in recording.

• The Y component of Y/C separate signals and the Y component of component signals output from the VTR/ CCU connector.

3) It is necessary to fit the optional DSBK-301A Index Picture Board.

12 Chapter 1 Overview

PCM digital audio

Equipped with DV OUT connector

Recording/playback can be set to audio lock mode. You are able to select between two-channel recording (with a sampling frequency of 48 kHz) mode or fourchannel recording (with a sampling frequency of 32 kHz) mode (CH-1 and CH-2 only).

Equipped with audio output connectors

During recording or playback, audio output can be monitored via a built-in speaker, a connected earphone or via (two-channel) audio output connectors.

Color playback

Connect an external video monitor for color playback (playback adaptor not required). This camcorder is equipped with two video monitor connectors: one for composite video output and the other for S-video output.

The DV OUT connector is i.LINK

compatible. You can connect Sony equipment with DV input connectors. You can control cut editing, dubbing, recording, and recording pause if you connect the DSR-70A/70AP Digital Videocassette Recorder (with the DSBK-140 i.LINK/DV Input/Output Board fitted) to the DV OUT connector on the camcorder, using an i.LINK cable (DV connecting cable). (See pages 29, 51, and

64.)

Other Features

Can be combined with portable VCR and CCU

You can connect Betacam VCRs, commercial S-VHS VCRs, and the CCU-M5A/M5AP to the 26-pin VTR/ CCU connection on the front panel.

Chapter 1 Overview

VCR data display

This camcorder is able to display the following data on the viewfinder screen.

• Time values (counter, time code, or user bit values)

• Audio recording levels

• Remaining tape time

• Operation mode of the VCR section

• Remaining battery capacity

• ClipLink information

1) is a trademark of Sony Corporation and indicates that this product is in agreement with IEEE 1394-1995 specifications and their revisions.

Chapter 1 Overview 13

Location and Function of Parts

Using the CD-ROM Manual

The supplied CD-ROM includes operation manuals for the DSR-370/570WS series of digital camcorders and players (English, Japanese, French, German, Italian and Spanish versions).

Chapter 1 Overview

CD-ROM System Requirements

The following are required to access the supplied CDROM disc.

• Computer: PC with MMX Pentium 166 MHz or

faster CPU, or Macintosh computer with PowerPC CPU.

- Installed memory: 32 MB or more

- CD-ROM drive: × 8 or faster

• Monitor: Monitor supporting resolution of 800 × 600

or higher

When these requirements are not met, access to the CD-ROM disc may be slow, or not possible at all.

Preparations

To Read the CD-ROM Manual

To read the operation manual contained in the CDROM disc, do the following.

1 Insert the CD-ROM disc in your CD-ROM drive.

A cover page appears automatically in your browser. If it does not appear automatically in the browser, double click the index.htm file on the CD-ROM disc.

2 Select and click the operation manual that you

want to read.

A PDF file of the operation manual opens.

Note

If you lose the CD-ROM disc or become unable to read its content, for example because of a hardware failure, contact a Sony service representative.

The following software must be installed on your computer in order to use the operation manuals contained in the CD-ROM disc.

• Microsoft Internet Explorer Version 4.0 or higher, or

Netscape Navigator Version 4.0 or higher

• Adobe Acrobat Reader Version 4.0 or higher

Notes

• If Microsoft Internet Explorer is not installed, it may

be downloaded from the following URL: http://www.microsoft.com/ie

• If Netscape Navigator is not installed, it may be

downloaded from the following URL: http://home.netscape.com/

• If Adobe Acrobat Reader is not installed, it may be

downloaded from the following URL: http://www.adobe.com/products/acrobat/ readstep.html

• MMX and Pentium are registered trademarks of Intel

Corporation or its subsidiaries in the United States and other countries.

• PowerPC is a registered trademark of International

Business Machines Corporation.

• Macintosh is a registered trademark of Apple Computer,

Inc.

• Microsoft is a registered trademark of Microsoft

Corporation in the United States and/or other countries.

• Netscape Navigator is a registered trademark of Netscape Communications Corporation in the U.S. and other countries.

• Adobe and Acrobat are registered trademarks of Adobe Systems Incorporated in the United States and/or other countries.

14 Chapter 1 Overview

Location and Function of Parts

Front View

0 Switch guard

How to remove the switch guard

1. Detach the two screws (M3).

2. Remove the switch guard, and replace the screws detached in step 1.

Chapter 1 Overview

1 MIC IN +48 V connector

2 VF connector

3 FILTER control

4 Lens mount

5 SHUTTER switch

6 TAKE button

7 AUDIO LEVEL knob

8 WHT/BLK switch

9 VTR button

1 MIC (microphone) IN +48 V connector (XLR 3-

pin, female)

Connect the supplied microphone or an optional

microphone (operable with a 48 V supply).

2 VF (viewfinder) connector (20-pin)

This is the connector for the DXF-801/801CE

viewfinder.

3 FILTER control

Select the color temperature conversion filter

appropriate to the lighting conditions. (See page 58.)

4 Lens mount

Attach the zoom lens here.

5 SHUTTER switch

Use this switch to set the shutter speed, CLS (clear scan), or EVS setting (see page 130). Usually, set this switch to OFF.

6 TAKE button

Press this button to specify an editing point (Mark IN/ OUT or Cue point) at the current tape position during shooting. (See page 79.)

7 AUDIO LEVEL knob

You can use this knob to manually adjust the channel 1 audio recording level.

8 WHT/BLK (white/black) switch

This switch is used for automatic adjustment of the white balance and black balance. (See pages 126 to

129.)

9 VTR button

Press this button to start and stop recording on the VCR.

0 Switch guard

Prevents mis-operation of the EZ MODE button (4 on page 17), A.IRIS MODE switch (6 on page 17),

and ATW button (qf on page 17). When using these buttons and switch, open the guard.

Chapter 1 Overview 15

Location and Function of Parts

Right Side View

Front section

Chapter 1 Overview

1 EZ FOCUS button

2 EDIT SEARCH buttons

3 LIGHT switch

4 EZ MODE button and indicator

5 ZEBRA button and indicator

6 A.IRIS MODE switch and indicator

1 EZ FOCUS button

Press this button to turn the “easy focus” function on. This opens the iris, to make it easier to focus before shooting. The indication “EZ FOCUS” appears in the viewfinder while the function is on; to turn it off, press the EZ FOCUS button again. If left on, the function automatically turns off after about ten seconds.

Note

If the “easy focus” function is still on when you press the VTR button, it turns off automatically and recording starts about one second later.

7 MENU switch

8 W.BAL switch

9 MENU dial

0 POWER switch

qa OUTPUT/DL/DCC+ switch

qs NG button

qd GAIN switch

qf ATW button and indicator

2 EDIT SEARCH buttons

You can see the search playback while pressing either of these buttons at recording pause mode to quickly find the next recording start point. Two playback speeds are available. Press either of the buttons to the inner position to increase the speed.

3 LIGHT (video light) switch

Controls the video light connected as follows.

AUTO: turns on the video light during recording if

the power switch on the light is set to on.

MAN (manual): allows the power switch on the

video light to turn the light on and off.

16 Chapter 1 Overview

4 EZ (“easy”) MODE button and indicator

Press this button (EZ mode on) when you want to shoot immediately, with automatic adjustment of the camcorder settings to standard values. (See page 104 for EZ mode setting.) When this function is used, the iris and the white balance are adjusted automatically. (The total level control system functions.) Press this button again to return the camcorder to the previous settings (EZ mode off).

Note

EZ mode does not function in the following cases.

• When the RM-M7G Remote Control Unit is

connected

• When the CCU-M5A/M5AP Camera Control Unit is

connected

• When external analog signals are being input.

5 ZEBRA button and indicator

Depress this button to display a zebra pattern (diagonal stripes) in the viewfinder.

Depending on the zebra setting in advanced menu page 4 (see page 102), the zebra 1 for video levels between 70 to 90 IRE (or 70 to 90%) and the zebra 2 for video levels 100 IRE or more (or 100% or more) can be displayed independently or simultaneously.

9 MENU dial

Use this dial to change menu pages or settings.

0 POWER switch

Powers the camcorder on or off.

qa OUTPUT/DL/DCC+ (DynaLatitude/dynamic contrast control plus) switch

Use this switch to select the DCC+ function, the DynaLatitude function, or color bar output. Select the CAM/DCC+ position in most cases.

CAM/DCC+: This activates the DCC+ function.

This prevents color faults when shooting highintensity subjects.

CAM/DL: This setting uses the DynaLatitude

function, which finely adjusts the contrast of each pixel according to a histogram of luminance signal levels. Access advanced menu page 2 to set the DynaLatitude function ON or OFF. The DynaLatitude effect can be set to any of three levels, Low, STD (standard), and High with basic menu page 2.

BARS: This setting displays color bars.

For details of menu operation, see Chapter 4 “Viewfinder Screen Indications and Menus” (See page 85).

Chapter 1 Overview

6 A.IRIS (auto iris) MODE switch and indicator

When you use the auto iris function (by setting the iris selector on the lens to A), set this switch to suit the shooting conditions. Selecting BACK L gives more light to back-lit subjects, and selecting SPOT L adjusts for high contrast in spot-lit subjects. For normal shooting, set this switch to STD.

7 MENU switch

When you press this switch to the ON position, the basic menu is displayed. Keep pressing it to the ON position to cycle through the various menu displays. When you press the switch to the STATUS position, the camcorder’s status (of current settings) is displayed.

8 W. BAL (white balance) switch

This selects the white balance setting from the preset value, the value in memory A or the value in memory B. (See page 126.) You can select the preset white balance at 3200 K or 5600 K using the FILTER control (3 on page 15). You can change the preset color temperature on basic menu page 2. (See page

93.)

qs NG button

When using the ClipLink function during shooting, you can designate a particular scene as “NG” (No Good) by pressing this button before shooting the next scene. Press the button again to cancel the NG setting.

qd GAIN switch

This selects one of the three gain settings, high, medium or low. You can choose the gain values assigned to the H, M and L settings from values from

–3 dB to 24 dB + DPR and hyper gain. (See page

100.) The factory default selections are 18 dB (H), 9

dB (M) and 0 dB (L).

Note

When the HYPER GAIN switch (7 on page 25) is in the ON position, the GAIN switch has no effect.

qf ATW (auto tracing white balance) button and indicator

Press this button, turning the indicator on, when you to automatically adjust the white balance to follow changes in the lighting conditions. (See page 128.)

Chapter 1 Overview 17

Location and Function of Parts

Rear section

Chapter 1 Overview

EJECT

STOP

1 EJECT button

F FWD

PLAYREW

2 Tape transport buttons and indicators

3 EARPHONE connector

4 WARNING indicator

5 LIGHT switch

6 DISPLAY switch

7 AUDIO LEVEL (CH-1/CH-2) knobs

8 Display window

9 RESET/(MENU SET) button

0 Speaker

qa ALARM knob

qs MONITOR knob

1 EJECT Z button

Press to open the cassette holder (1 on page 27) when the camcorder is powered.

2 Tape transport buttons and indicators

These buttons transport the tape as shown below.

Note

During recording, none of these buttons operates.

Buttons

REW m

F FWD M Fast forwards the tape. The indicator lights

PLAY N Plays back the recorded video. The indicator

STOP x

Operation

Rewinds the tape. The indicator lights while the tape is being rewound.

Press while the tape is being rewound or during playback to view reverse search playback.

while the tape is being fast forwarded. Press while the tape is being fast forwarded

or during playback to view forward search playback.

lights during playback.

Stops the tape.

3 EARPHONE connector (mini-jack)

Connect an earphone or headphones. This outputs the same sound that would be output to the speaker (0 on page 21), but mutes the speaker.

4 WARNING indicator

This lights or blinks when an abnormality occurs.

For details, see “Warning System” on page 142.

5 LIGHT switch

This switches the display window (8 on page 19) light on or off.

6 DISPLAY switch

Switches time value indication shown in the display window (8 on page 19).

COUNTER: Shows the tape transport time in

HH:MM:SS (hours, minutes and seconds).

TC: Shows the time code value. U-BIT: Shows the user bit data in the time code.

18 Chapter 1 Overview

7 AUDIO LEVEL (CH-1/CH-2) (audio recording level adjustments for channels 1 and 2) knobs

When the AUDIO SELECT (CH-1/CH-2) switches (4 on page 23) are set to MAN, these knobs adjust the audio levels being recorded on channels 1 and 2.

A Playback indication

B DATE indication

C Non-drop frame indication (DSR-370/570WS only)

PB DATE NDF EXT-LK HOLD

S Time value

indication

R Clip remaining

indication

Q Tape remaining

indication

P Battery capacity

indication

O Service indication

a) When the optional DSBK-301A is fitted

H MIN SEC FRM

CLIP TAPE BATT

DIAG

RF SERVO HUMID SLACK

The audio levels are indicated in the display window 8. For details, see “8 Display window”.

8 Display window

Shows the following items. Use the LIGHT switch (5 on page 18) to light up the display window.

D External synchronization lock indication

E Hold indication

F Audio level indicators

OVER OVER

-12

N Warning indications

CONT

DVCAM

M Audio mode indications

-20

-30

-40

∞

8 32k

8 48k

G ClipLink log data indication

H ClipLink continue

indication

I IP indication

CONT

DVCAM

J Lithium backup

K DVCAM indication

L Cassette memory indication

battery warning

Chapter 1 Overview

Indications in the display window

Indication

Description

A Playback indication Appears during playback, fast forward or rewind with the time data display showing a

time code or user bit value.

B DATE indication Appears when the date or time is displayed in the time value indication area S.

C Non drop-frame indication (DSR-

Appears when non-drop frame mode is selected.

370/570WS only)

D External synchronization indication

Appears when the internal time code generator is locked to an external signal input to the TC IN connector (3 on page 28).

E Hold indication Appears when the internal time code generator is stopped. F Audio level indicators These show the audio recording or playback levels of channel 1 and channel 2.

G ClipLink log data indication

H ClipLink continue indication

Appears when using a cassette with cassette memory containing ClipLink log data.

Appears when back space editing using ClipLink function is possible.

I IP (Index Picture) indication Appears when the ClipLink function is set to on in the VCR menu and Index Picture

recording is allowed. (The optional DSBK-301A is required.)

(Continued)

Chapter 1 Overview 19

Location and Function of Parts

Indication Description

J Lithium backup

battery warning

Chapter 1 Overview

K DVCAM

indication

L Cassette

memory indication

M Audio mode

indications

N Warning

indications

Appears when the voltage of the internal lithium backup battery (CR2032) is low. If this indication appears, replace the lithium backup battery immediately.

For further information about replacing lithium battery, see “Inserting and Replacing the Lithium Battery” (page 37).

Disappears when the cassette being played back is not for DVCAM format.

Appears when using a cassette with cassette memory.

These show audio recording/playback mode.

Fs32k: 4-channel mode (32kHz sampling frequency)

Fs48k: 2-channel mode (48kHz sampling frequency)

For further information about selecting audio recording mode, see “Selecting Audio Recording Mode Menu 212” (page 123).

Include the following.

RF: Appears when the video heads are clogged, or when there is a fault in the

recording system.

SERVO: Appears when the servo lock is not functioning.

HUMID: Appears when there is condensation on the drum.

SLACK: Appears when there is a tape winding fault.

Indications in the display window (continued)

O Service

indication

P Battery

capacity indication

For measures against warning indications, see “Warning System” (page 142).

Appears during maintenance or VCR menu operations during normal operation.

This indicates the battery capacity and voltage as shown below. Change menu setting for the battery you are using.

(page 117)

. It does not appear

For menu settings, see “Selecting Battery Capacity Indication Menu 206” (page 120).

Battery voltage

Indication

BATT E[xxxxxx]F 15.0 V or more 12.5 V or more 14.0 V or more

BATT E[xxxxx ]F 14.0 to 15.0 V 12.0 to 12.5 V 13.65 V to 14.0 V

BATT E[xxxxp]F 13.0 to 14.0 V 11.75 to 12.0 V 13.40 V to 13.65 V

BATT E[xxx p]F 12.0 to 13.0 V 11.5 to 11.75 V 12.90 V to 13.40 V

BATT E[xxpp]F 11.3 to 12.0 V 11.3 to 11.5 V 12.40 V to 12.90 V

BATT E[xxpp]F (blinking)

BATT E[x pp]F (blinking) 11.0 to 11.25 V 11.0 to 11.25 V 11.00 V to 12.25 V

BATT E[ppp]F (blinking) 11.0 V or less 11.0 V or less 11.0 V or less

1) Replace the battery pack when this indication appears.

BP-L40/L40A/ NP-1B/BP-90A L60/L60A/L90/L90A

11.25 to 11.3 V 11.25 to 11.3 V 12.25 V to 12.40 V

BP-M50/M100

20 Chapter 1 Overview

Indications in the display window (continued)

Indication Description

Q Tape remaining indication During recording or pause mode, this indication shows the remaining tape time as

R Clip remaining indication

shown below. It is not displayed when no cassette is loaded.

Indication Tape time remaining

TAPExxxxxxx 30 minutes or more

TAPExxxxxx 25 to 30 minutes

TAPExxxxx 20 to 25 minutes

TAPExxxx 15 to 20 minutes

TAPExxx 10 to 15 minutes

TAPExx 5 to 10 minutes

TAPEx 2 to 5 minutes

TAPEx (blinking) 0 to 2 minutes

TAPE (blinking) End of tape

This shows how many clip shots or Cue points can be recorded

Indication Clip shots Cue point

CLIPxxxxxx 51 or more 101 points or more

CLIPxxxxx 41 to 50 81 to 100 points

CLIPxxxx 31 to 40 61 to 80 points

CLIPxxx 21 to 30 41 to 60 points

CLIPxx 11 to 20 21 to 40 points

CLIPx 1 to 10 1 to 20 points

CLIPx (blinking)

CLIP Cannot record

CLIP (blinking)

1 to 3 1 to 6 points

Cannot record

Chapter 1 Overview

1) The optional DSBK-301A is required for Index Picture recording.

2) When back space editing using ClipLink function is possible (when CONT is displayed)

S Time value indication Depending on the DISPLAY switch (6 on page 18) setting, this shows a counter

9 RESET/(MENU SET) (counter reset/VCR

value, time code value or user bit value. Press the MENU button (1 on page 22) to display the VCR menu.

Also, this button is used to change menu settings.

menu) button

Resets the time value shown in the display window. This button operates differently depending on settings

For details on the VCR menu, see “Setting on the VCR Section VCR Menu” (page 117).

of the DISPLAY switch (6 on page 18) and the TC mode switch 1 (9 on page 23) and 2 (8 on page 23).

0 Speaker

Outputs the recorded or playback audio. When a

Switch setting RESET button operation

DISPLAY: COUNTER Resets counter value to

0:00:00.

DISPLAY: TC TC mode switch 1: PRESET TC mode switch 2: SET

DISPLAY: U-BIT TC mode switch 1: PRESET TC mode switch 2: SET

Resets time code to 00:00:00:00.

Resets user bit 00 00 00 00.

warning indicator appears in the viewfinder or display window, the speaker sounds a warning tone. The speaker is muted (does not output a warning tone) when an earphone is connected to the EARPHONE connector (3 on page 18).

For details on the warning tone, see “Warning System” (page 142).

a)Bits of time code recorded on tape, in which users can

record necessary information.

Chapter 1 Overview 21

Location and Function of Parts

qa ALARM (alarm tone volume adjustment) knob

Controls the volume of the warning tone that is output via the speaker (0 on page 21) or EARPHONE connector (3 on page 18). Turning this knob to the minimum setting mutes the alarm tone.

Chapter 1 Overview

Operation panel under the cover

Right side

qs MONITOR (monitor volume adjustment) knob

Controls the volume of the sound other than the warning tone that is output via the speaker (0 on page

21) or EARPHONE connector (3 on page 18). Turning this knob to the minimum setting mutes the audio output.

1 MENU button

2 ADVANCE button

3 SHIFT button

ClipLink

ADVANCE SHIFT

PRESET

CH-1

REGEN

CH-2

DATE/TIME

REC TIME SKIN DTL EXT VTR

TTL

DUR

OFF

TTL RESET

OFF

HYPER

GAIN

SET

SETUP

FILE STD

COMPONENT.

OFF

PARALLEL

INT ONLY

EXT ONLY

FRONT MIC

LOW CUT

OFF

OUTPUT

VBS

Y/C

VTR

TRIGGER

MONITOR SELECT

MIX

EXT

CONTINUE

1 MENU button

Press this button to display the VCR menu in the display window.

For details about the VCR menu, see “Setting on the VCR Section —VCR Menu” (page 117).

2 ADVANCE button

When setting time code and user bit values, or at menu

AUDIO LEVEL

F-RUN

R-RUN

MONITOR OUT

CHARACTER

OFF

SET

LITHIUM BATT

VJ MIC

WIRELESS

AUTO

MAN

AUDIO SELECT

CH-1

AUDIO IN

FRONT

REAR

CH-2

4 AUDIO SELECT

(CH-1/CH-2) switches

5 AUDIO IN (CH-1/

CH-2) switches

6 Lithium battery compartment

7 MONITOR OUT CHARACTER switch

8 TC mode switch 2

9 TC mode switch 1

0 ClipLink CONTINUE button

qa MONITOR SELECT switch

setting, press this button to increment the digit that has been selected with the SHIFT button (3 on page 23). In other case, keep pressing this button to show the clip remaining indication instead of time value. (Example: CLIP 045)

For time code and user bit settings, see page 71.

On how to use the ADVANCE button for menu settings, see “Setting on the VCR Section —VCR Menu” (page 117).

22 Chapter 1 Overview

3 SHIFT button

When setting time code and user bit values, or at menu setting, keep pressing this button to select a digit. The selected digit will start blinking.

In other case, keep pressing this button to show the date (when the DISPLAY switch (6 on page 17) is set to U-BIT) and time (when the DISPLAY switch is set to TC) instead of time value.

For time code and user bit settings, see page 71.

On how to use the SHIFT button for menu settings, see “Setting on the VCR Section —VCR Menu” (page 117).

8 TC (time code) mode switch 2

Sets the mode for advancing time code values when the TC mode switch 1 9 has been set to PRESET.

F-RUN: The time code advances continuously

whether or not the camcorder is recording. Use this setting to align the time code value with real time.

SET: Use this setting to set the time code or user bit

value.

R-RUN: The time code value advances only during

recording. Use this setting to have consecutive recordings on the tape.

Chapter 1 Overview

4 AUDIO SELECT (CH-1/CH-2) (audio recording level adjustments manual/auto selection for channels 1 and 2) switches

These select the audio recording level adjustment method.

AUTO: Use the AGC (automatic gain control) circuit

to automatically adjust the audio level.

MAN: Enables users to manually adjust the AUDIO

LEVEL (CH-1/CH-2) knobs (7 on page 19) for each channel. Select AUTO if excess input levels are likely to occur.

5 AUDIO IN (CH-1/CH-2) (audio input selection for channels 1 and 2) switches

These select the input signals to channels 1 and 2.

FRONT: Signals from the microphone connected to

the MIC IN +48 V connector.

VJ MIC: Signals from the remote control unit with

microphone connected to the REMOTE connector 2

WIRELESS: Signals from the WRR-855A

synthesized tuner connected to the WRR connector via the CA-WR855 Camera Adaptor.

REAR: Signals from a microphone or external

equipment connected to the AUDIO IN (CH-1/ CH-2) connectors.

6 Lithium battery compartment

Insert the supplied CR2032 Lithium Battery.

On how to fit the lithium battery, see page 37.

7 MONITOR OUT (monitor output) CHARACTER switch

Set ON to superimpose text information on the monitor output.

Note

Set this switch ON when using the freeze mix function.

Note for the DSR-370/570WS

There are two time code frame modes: drop-frame (DF) mode and non drop-frame (NDF) mode. This product is shipped with drop-frame mode selected.

For details on switching between drop-frame mode and non drop-frame mode, see “Selecting Frame Mode (DF/NDF) for Time Code (for DSR-370/570WS only) —Menu 204” (page 119).

For details on drop-frame mode and non drop-frame mode, see “Drop-frame mode (for DSR-370/570WS only)” on page

74.

9 TC (time code) mode switch 1

Selects between resetting the time code value or continuing from the time code value at the end of the previous recording.

PRESET: This starts recording time code values on

the tape from the currently set value.

REGEN: During back space editing, this reads the

tape’s current time code value and sets the time code to record starting from that value. The time code value is advanced in R-RUN mode regardless of the setting on TC mode switch 2 8.

DATE/TIME: This synchronizes the time code to

the real time clock set in the VCR menu (see page

119). In this case the time code of the DSR-370/ 570WS is recorded in DF (drop-frame mode).

Note

If the ClipLink function is set to on (meaning ClipLink shooting is allowed) in menu 211 and CONT is displayed in the display window, regardless of the setting of this switch, the time code generator automatically enters the REGEN mode at recording. (When not performing ClipLink shooting, set the ClipLink function to oFF (see page 123)).

Chapter 1 Overview 23

Location and Function of Parts

0 ClipLink CONTINUE button

When restarting ClipLink shooting, press this button to add the new clip at the end of the recorded clips.

Note

Chapter 1 Overview

When restart recording without pressing this button, the pre-recorded ClipLink log data and Index Pictures are deleted.

For details , see “ClipLink Shooting” (page 77).

Left side

REC TIME SKIN DTL EXT VTR

TTL

DUR

OFF

TTL RESET

HYPER

GAIN

OFF

qa MONITOR SELECT (audio monitor selection) switch

Selects audio output via the speaker (0 on page 21) or earphone.

CH-1: Channel 1 audio MIX: Mixed audio (channels 1 and 2) CH-2: Channel 2 audio EXT: The sound selected by an external VCR

connected to the VTR/CCU connector (0 on page 29)

1 REC TIME switch

2 SKIN DTL switch

3 EXT VTR OUTPUT switch

ClipLink

ADVANCE SHIFT

PRESET

CH-1

REGEN

CH-2

DATE/TIME

F-RUN

R-RUN

MONITOR OUT

CHARACTER

OFF

SET

LITHIUM BATT

VJ MIC

WIRELESS

AUDIO LEVEL

AUTO MAN

AUDIO SELECT

CH-1

AUDIO IN

FRONT

REAR

CH-2

OUTPUT

COMPONENT.

VBS

OFF

Y/C

SET

PARALLEL

INT ONLY

EXT ONLY

SETUP

FRONT MIC

LOW CUT

FILE

STD

OFF

VTR

TRIGGER

MONITOR SELECT

MIX

EXT

CONTINUE

1 REC (recording) TIME switch

Selects the recording time indication in the viewfinder.

TTL (TOTAL): Displays the total recording time.

The total recording time is not reset even when you stop the VCR and power off the camcorder, for example, to replace the battery pack.

DUR (DURATION): Displays the recording time of

the current cut.

24 Chapter 1 Overview

4 VTR TRIGGER switch

5 FRONT MIC LOW CUT switch

6 SETUP switch

7 HYPER GAIN switch

8 SKIN DTL SET button

9 TTL RESET button

OFF: Switches off the recording time display.

If, however, in advanced menu 6 you set the time code display item (TC IND) to ON (see page

103), then the VCR time data (time code, counter, or user bit value) is displayed.

Note

The recording time displayed when this switch is set to TTL or DUR is obtained by counting the duration of the internal reference signal input to the camcorder.

The value may not agree exactly with the value derived from the time code values. Furthermore, the value displayed may not be correct when another manufacture’s VCR is connected to the camcorder.

2 SKIN DTL (skin detail) switch

Set this switch to ON to use the skin detail correction function.

7 HYPER GAIN switch

Setting this switch to ON increases the gain by a factor of about 60 with respect to 0 dB (a 30 dB increase by electronic amplification and a 6 dB increase for DPR, bringing about a total gain increase of 36 dB, or an increase 42 dB for the DSR-570WS/570WSP only). When this switch is in the ON position, the indication “HYPER” appears in the viewfinder, and the GAIN UP indicator in the viewfinder also lights. When finished shooting, return this switch to OFF position. The “HYPER” indication disappears and the GAIN UP indicator goes out.

Chapter 1 Overview

For details, see “Skin Detail Correction” (page 138).

3 EXT VTR OUTPUT switch

Depending on the external VCR connected to the VTR/CCU connector (0 on page 29), this switches the video signal output to the VCR.

COMPONENT, VBS: Component/composite video

signal

Y/C: S-video signal

Note

When a CCU (camera control unit) is connected, component video signals/composite video signals are output, regardless of the setting of this switch.

4 VTR TRIGGER switch

Sets the function of the VTR button on the camcorder or lens when a VCR is connected to the VTR/CCU connector (0 on page 29) or DV OUT connector (8 on page 29).

PARALLEL: Operates both internal and external

VCRs.

INT ONLY: Operates the internal VCR only.

External VCR operation is performed locally.

EXT ONLY: Operates the external VCR only. Set this switch to INT ONLY when you need to do cut editing or dubbing using the DV OUT connector.

Note

Increasing the gain with this switch reduces the horizontal resolution by approx. 50%.

8 SKIN DTL (skin detail ) SET button

Press this button with the SKIN DTL switch 2 to display the area detect cursor on viewfinder screen. Place the cursor on the target and press this button to perform skin detail correction.

For details, see “Skin Detail Correction” (page 138).

9 TTL (total) RESET button

Pressing this button resets the total recording time (TTL selection) to 0.

5 FRONT MIC LOW CUT switch

Set this switch to ON to insert a high-pass filter in the microphone circuit, reducing wind noise.

Normally leave the switch in the OFF position.

6 SETUP switch

This selects the setup method for this camcorder.

FILE: Set up using both a setup file and the setup

menu.

STD: Set up using the setup menu. The setup file is

no longer displayed.

Chapter 1 Overview 25

Location and Function of Parts

Left and Upper View

Front section

Chapter 1 Overview

1 Shoulder strap fitting

2 Attachment shoe for large viewfinder

3 Accessory fitting shoe and screw hole

4 Viewfinder left-to-right positioning ring

5 Viewfinder fitting shoe

6 REMOTE connector 1

7 Viewfinder front-to-back position locking knob

8 Fitting for optional microphone holder

9 Video light connector

1 Shoulder strap fitting

To use the supplied shoulder strap, fix one end here and the other end to the right side. (See page 45.)

2 Attachment shoe for large viewfinder

This allows you to attach the optional electronic viewfinder. (See page 42.)

3 Accessory fitting shoe and screw hole

Attach optional video lights or other accessories. (See page 44.)

4 Viewfinder left-to-right positioning ring

Loosen this ring to adjust the left-to-right position of the viewfinder. (See page 41.)

5 Viewfinder fitting shoe

Fix the DXF-801/801CE Viewfinder.

0 LENS connector

qa VIDEO OUT connector

qs REMOTE connector 2

6 REMOTE connector 1 (mini-jack)

Connect the RM-LG1 Remote Control Unit to enable remote operation of the ClipLink function.

Note

The RM-81 cannot be connected.

If you connect the optional cable (Sony part number: 1-790-779-11) to this connector, you can control the zoom using the optional RM-VJ1 Remote Control Unit (equipped with microphone and monitor), even when using the conventional lens.

For details, consult your Sony dealer.

7 Viewfinder front-to-back position locking knob

Loosen this knob to adjust the front-to-back position of the viewfinder. (See page 41.)

26 Chapter 1 Overview

8 Fitting for optional microphone holder

You can fit an optional CAC-12 Microphone Holder here. (See page 43.)

9 Video light connector

A video light with a maximum power consumption of 30 W such as the Anton Bauer Ultralight 2 or equivalent can be connected.

0 LENS connector (12-pin)

If you use a lens with cable, connect the lens cable.

qa VIDEO OUT connector (BNC)

This outputs the video signal captured by the camcorder.

Rear section

qs REMOTE connector 2 (10-pin)

Connect the optional RM-M7G Remote Control Unit to this connector. Set the CAMERA SELECT switch on the bottom of RM-M7G to 1.

Notes

• EZ mode cannot be used if the RM-M7G is connected to the camcorder.

•Be sure to turn off the power of the camcorder before connecting the RM-M7G.

•Be sure to turn off the power of the camcorder before disconnecting the equipment connected to this connector. Otherwise, the camcorder will not work properly.

• To control this unit from a CCU (camera control unit), connect the RM-M7G to the CCU.

Chapter 1 Overview

a) When the optional DSBK-501/501P is fitted

1 Cassette holder

Power the camcorder and press the EJECT button to open the lid. Insert the cassette and close the lid by pressing the indication “PUSH” .

2 GEN LOCK IN (gen lock video input)/VIDEO IN (video input) connector (BNC)

1 Cassette holder

2 GEN LOCK IN/VIDEO IN connector

3 TC IN connector

4 TC OUT connector

5 S VIDEO OUT connector

6 MONITOR OUT connector

7 AUDIO OUT CH-1/CH-2 connectors

GEN LOCK IN: When synchronizing the camcorder

to an external signal, input a reference video signal (VBS or BS). (See page 93.)

VIDEO IN: When the optional DSBK-501/501P

Analog Composite Input Board is fitted to the camcorder, you can input the analog video signals (VBS) to this connector.

Chapter 1 Overview 27

Location and Function of Parts

3 TC IN (time code input) connector (BNC)

Input an external signal for synchronizing the built-in

time code generator. Use an SMPTE (DSR-370/

570WS) or EBU (DSR-370P/570WSP) time code

signal.

Chapter 1 Overview

Note

Use a jitterless LTC signal. Using an LTC signal

reproduced by other equipment may cause the

camcorder to malfunction.

4 TC OUT (time code output) connector (BNC)

This outputs time code signals from the built-in time

code generator. When a time code signal is input to

the TC IN connector, this output signal is synchronized

to it.

For details about time code, see “Setting the Time code

Value” on page 73.

5 S VIDEO OUT (S-video output) connector (DIN 4-pin)

This outputs the image being shot or played back as Svideo signals. Connect to the S-video input connector on an external VCR or video monitor.

6 MONITOR OUT (output) connector

Outputs the image being shot or played back as composite video signals. Connect to the video input connector on an external VCR or video monitor.

Note

The output signal from this connector may discontinue when switching the operation between recording and playback. Do not use as a reference signal for external equipment.

7 AUDIO OUT CH-1/CH-2 (audio output channel 1 and 2) connectors (phono jacks)

These output the sound being recorded or played back. Connect to a stereo amplifier or video monitor’s audio input connectors.

Rear and Bottom

1 TALLY indicator

2 TALLY switch

3 Battery attachment

interface

4 DC IN connector

5 AUDIO IN CH-1/CH-2

connectors and input selection switches

6 WRR connector

7 Cable clamp

8 DV OUT connector

9 DC OUT connector

0 VTR/CCU connector

28 Chapter 1 Overview

qa BREAKER button

1 TALLY (back tally) indicator (red)

This indicator lights during recording. It will not light if the TALLY switch 2 is set to OFF. This indicator also blinks to indicate warnings in the same manner as the REC/TALLY indicator in the viewfinder.

2 TALLY switch

Set this switch to ON to activate the TALLY indicator 1 function.

See “Connecting to Audio System” (page 46) for more information about how to connect a UHF synthesizer tuner. See “Connecting a CA-370 Intercom Adaptor” (page 48) for more information about how to connect an intercom adaptor.

Chapter 1 Overview

7 Cable clamp

Fasten an i.LINK cable (DV connecting cable) to the clamp using the supplied binding tie so that the plug is not pulled out from the DV OUT connector 8.

For details, see “Warning System” on page 142.

3 Battery attachment interface

Attach a battery pack or an AC-DN1/DN2A AC Adaptor. When using the WRR-855A synthesized tuner (for wireless microphones), attach the CAWR855 Camera Adaptor here.

For information about fitting a battery pack or an AC adaptor, see “Power Supply” (page 53). For information about attaching a synthesized tuner, see “Connecting to Audio System” (page 46).

4 DC IN (DC power input) connector (XLR 4-pin, male)

To use the camcorder with an AC power supply connect an optional AC-550/550CE or CMA-8A/ 8ACE AC Adaptor.

5 AUDIO IN CH-1/CH-2 (audio input channel 1 and 2) connectors (XLR 3-pin, female) and input selection switches

Connect a microphone or other external audio equipment. Set the input selection switches as shown below according to the microphone or equipment.

MIC+48V ON (right position): For connecting to a

48-V microphone

Note

If this position is selected for a microphone other than 48-V microphone, the microphone may be damaged.

i.LINK cable (DV connecting cable)

Binding tie

8 DV OUT connector (6-pin)

Connect to the DV input connector of an external VCR via an i.LINK cable.

Notes

• This connector will not work as an input connector.

• When external equipment, such as a VCR, is

connected to this connector, the ClipLink function and the function for audio fade-in/fade-out during recording do not work.

9 DC OUT (DC power output) connector (4-pin, female)

This connector supplies power for a WRR-810A/860A UHF Portable Tuner.

0 VTR/CCU connector (26-pin, male)

Connect an external VCR or CCU-M5A/M5AP or other camera control unit.

MIC (center position): For connecting any

microphone other than 48-V microphone

LINE (left position): For connecting an external

audio signal source such as a stereo amplifier.

6 WRR (synthesizer tuner/intercom adaptor) connector (7-pin)

Connect a CS-WR855 Camera Adaptor with attached WRR-855 UHF Synthesizer Tuner, or a CA-370 Intercom Adaptor for the CCU-M5A/M5AP.

Notes

• This connector always outputs the signals from the camera. It is impossible to output the playback video of the internal VCR.

• The image size on the viewfinder or on the screen of the RM-VJ1 does not switch automatically, even if the aspect ratio (16:9/4:3) of the return signal, input from an external VCR, is switched.

Chapter 1 Overview 29

Location and Function of Parts

• When this connector is used with a battery pack attached, operation may be interrupted due to exhaustion of the batteries. To prevent this, see “Avoiding breaks in operation due to dead

Chapter 1 Overview

batteries” (page 54).

• When a CCU is connected to this connector and a

battery pack is attached, power is supplied automatically from the battery pack. Always power off the camcorder before attaching or detaching a battery pack or switching the power.

VCL-716BX Zoom Lens (for DSR-370K2/370PK2)

When using a lens other than VCL-716BX or VCL-719BX, see page 40 and page 134 (“Designating the lens”).

1 Iris ring

2 Zoom ring

3 Focus ring

qa BREAKER (breaker reset) button

If an excessive current flows in the internal circuits, the internal circuit breaker shuts off the power supply. Push this button after eliminating the cause of the excessive current.

4 MACRO selector

Lens hood

9 RET button

5 F.f adjustment ring

and F.f fixing knob

6 MACRO ring

7 ZOOM selector

8 Zoom remote control

connector

qa Instant automatic iris

adjustment button

qs Iris selector

qd Motorized zoom lever

0 VTR button

30 Chapter 1 Overview

+ 130 hidden pages