Siemens Mammomat 3000 Nova User manual

MAMMOMAT 1000/3000/3000 Nova
Service
Repair Instructions
Replacement of metal curtains, wi res, wire wheels and spring
© Siemens AG 2000
The reproduction, transmission or use of this docu men t or its con tent s is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model _or_ design,_are_ reserved.
English
Print No.: SPB7-230.091.11.01.02 Doc . Gen. Date: 09.00
Replaces: n.a. 65 58 758
0 - 2 Revision
Chapter Page Revision
All All 01
M1000/3000/3000 Nova SPB7-230.091.11 Page 2 of 4 Siemens-Elema AB Service Rev. 01 09.00 SPS-UD Solna, Sweden
Contents 0 - 3
Page
1 _______Prerequisites __________________________________________________1 - 1
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
Tools required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
Time required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 2
2 _______Work procedure________________________________________________2 - 1
Dismounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 - 1
Exchange upper and/or lower curtain . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 2
Exchange upper and/or lower wire . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 8
Exchange upper and/or lower wire wheel. . . . . . . . . . . . . . . . . . . . . . . 2 - 12
Exchange spring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 16
Siemens-Elema AB SPB7-230.091.11 Page 3 of 4 M1000/3000/3000 Nova Solna, Sweden Rev . 01 09.00 SPS-UD Service
0 - 4 Contents
This page intentionally left blank.
M1000/3000/3000 Nova SPB7-230.091.11 Page 4 of 4 Siemens-Elema AB Service Rev. 01 09.00 SPS-UD Solna, Sweden

Prerequisites 1

General 1

This document describes how to exchange the upper and the lower curtai n, the wires, the wire wheels and the spring at a MAMMOMAT 1000/3000/3000 Nova.
The upper curtain kit with part no. 65 22 291 contains the following parts:
Article Quantity Part no. See page
Upper curtain 1 64 82 934 2 - 2 Repair Instructions (this docu ment) 1 65 58 758
The lower curtain kit with part no. 65 22 317 contains the following parts:
Article Quantity Part no. See page
Lower curtain 1 64 82 942 2 - 2 Repair Instructions (this docu ment) 1 65 58 758
The wire kit with part no. 64 83 346 contains the following parts:
1 - 1
Article Quantity Part no. See page
Wire 2 64 82 496 2 - 8 Spring 1 63 46 647 2 - 16 Repair Instructions (this docu ment) 1 65 58 758
The wire wheel kit with part no. 64 83 296 contains the following parts:
Article Quantity Part no. See page
Wire wheel 2 64 62 118 2 - 12 Spacer 2 64 82 470 2 - 12 Locking ring 2 60 35 810 2 - 12 Screw 2 60 24 079 2 - 12 Washer 3 69 67 731 2 - 12 Washer 1 62 05 467 2 - 12 Washer 2 65 87 422 2 - 12 Repair Instructions (this docu ment) 1 65 58 758

Tools required 1

Standard service equipment

Time require d 1

Approximately 1 hour / 1 person.
Siemens-Elema AB SPB7-230.091.11 Page 1 of 2 M1000/3000/3000 Nova Solna, Sweden Rev . 01 09.00 SPS-UD Service
1 - 2 Prerequisites
WARNING
WARNING

Safety information 1

The edges of the metal curtains are very sharp and may cause severe injury.
When mounting the stand covers, make sure the screws at the top of the stand are securely tightened and have functioning con­tact washers. These screws are used to establish protective ground connections.
M1000/3000/3000 Nova SPB7-230.091.11 Page 2 of 2 Siemens-Elema AB Service Rev. 01 09.00 SPS-UD Solna, Sweden

Work procedure 2

Dismounting 2

1. Remove the cap.
2. Remove the stand covers.
3. Move the lifting carriage (1/Fi g. 1). The distance between the upper part of the lifting carriage and the top of the MAMMOMAT must be 625
+2 mm (Fig. 1).
2 - 1
Fig. 1
1
MAM00694
Siemens-Elema AB SPB7-230.091.11 Page 1 of 18 M1000/3000/3000 Nova Solna, Sweden Rev . 01 09.00 SPS-UD Service
2 - 2 Work procedure

Exchange upper and/or lower curtain 2

The information written in parenthe sis are valid during the exchange of lower curtain. The figures explains how to exchange the upper curtain.
1. Follow the work procedure described in t he chapter "Dismounting", Page 2 - 1.
2. To secure the lower (upper) curtai n from falling down during the exchange of upper (lower) curtain, place e.g. a screwdriver in a suitable hole of t he curtain holder and let the screwdriver l ean against the stand (Fig. 2)
Fig. 2
3. Loosen the lower wire wheel (1/Fig. 3).
1
Fig. 3
MAM00695
M1000/3000/3000 Nova SPB7-230.091.11 Page 2 of 18 Siemens-Elema AB Service Rev. 01 09.00 SPS-UD Solna, Sweden
Work procedure 2 - 3
4. Secure the lower (upper) wire from falli ng down e.g. with a cable tie (Fig. 4).
Fig. 4
5. Loosen the upper (lower) wire from the spri ng.
6. Remove the protective ground cable for the upper (lower) curtain (Fig. 5) .
Fig. 5
7. To unhook the curtain, pull the curtain down ( up) and push it to one side.
Siemens-Elema AB SPB7-230.091.11 Page 3 of 18 M1000/3000/3000 Nova Solna, Sweden Rev . 01 09.00 SPS-UD Service
2 - 4 Work procedure
WARNING
8. Loosen four screws to remove the upper (l ower) curtain (1/Fig. 6).
1
1
MAM00694
Fig. 6
The edges of the metal curtains are very sharp and may cause severe injury.
9. Mount the new curtain with the four screws and ho ok-up. The upper and lower curtain locks different, be sure to use the right one. It is also import ant that the curtain holder is turned right (Fig. 7).
Fig. 7
M1000/3000/3000 Nova SPB7-230.091.11 Page 4 of 18 Siemens-Elema AB Service Rev. 01 09.00 SPS-UD Solna, Sweden
Work procedure 2 - 5
10. Place two screwdrivers alt ernately into the holes of the upper (lower ) curtain holder and wind up the curtain holder bit by bit.
11. Secure the upper (lower) curt ain with a screwdriver (Fig. 8).
Fig. 8
Siemens-Elema AB SPB7-230.091.11 Page 5 of 18 M1000/3000/3000 Nova Solna, Sweden Rev . 01 09.00 SPS-UD Service
2 - 6 Work procedure
12. Attach the wire to the curtain hol der and wind the wire:
- 4.75 turns for the upper curtain ( 1/Fig. 9).
- 4.5 turns for the lower cu rtain (2/Fig. 9).
1
2
MAM00711
Fig. 9
13. Attach the wire to the spring.
14. Remove the securing screwdriver s.
M1000/3000/3000 Nova SPB7-230.091.11 Page 6 of 18 Siemens-Elema AB Service Rev. 01 09.00 SPS-UD Solna, Sweden
Work procedure 2 - 7
15. Tighten the wire wheel until the length of the spring is 160&5 mm (Fig. 10).
MAM00693
Fig. 10
16. Fit the stand covers.
17. Fit the cap.
18. Move the curtain up and down to check the fu nction.
Siemens-Elema AB SPB7-230.091.11 Page 7 of 18 M1000/3000/3000 Nova Solna, Sweden Rev . 01 09.00 SPS-UD Service
2 - 8 Work procedure

Exchange upper and/or lower wire 2

The information written in parenthe sis are valid during the exchange of lower wire. The figures explains how to exchange the upper wire.
1. Follow the work procedure described in t he chapter "Dismounting", Page 2 - 1.
2. To secure the upper and lower curtains from f alling down during the exchange of upper and/or lower wire, place e.g. sc rewdrivers in suitable holes of the curtain holders and let the screwdriver s lean against the stand (Fig. 11)
Fig. 11
3. Loosen the wire wheel (1/Fig. 12).
1
Fig. 12
MAM00695
M1000/3000/3000 Nova SPB7-230.091.11 Page 8 of 18 Siemens-Elema AB Service Rev. 01 09.00 SPS-UD Solna, Sweden
Work procedure 2 - 9
4. Secure the lower (upper) wire from falli ng down e.g. with a cable tie (Fig. 13).
Fig. 13
5. Loosen the upper (lower) wire from the spri ng and from the curtain holder.
Siemens-Elema AB SPB7-230.091.11 Page 9 of 18 M1000/3000/3000 Nova Solna, Sweden Rev . 01 09.00 SPS-UD Service
2 - 10 Work procedure
6. Attach the new wire to the curtain holder and wind the wire:
- 4.75 turns for the upper curtain ( 1/Fig. 9).
- 4.5 turns for the lower cu rtain (2/Fig. 9).
1
2
MAM00711
Fig. 14
7. Attach the new wire to the spring.
8. Remove the securing screwdrivers.
M1000/3000/3000 Nova SPB7-230.091.11 Page 10 of 18 Siemens-Elema AB Service Rev. 01 09.00 SPS-UD Solna, Sweden
Work procedure 2 - 11
9. Tighten the wire wheel until the length of the spring is 160&5 mm (Fig. 10).
MAM00693
Fig. 15
10. Fit the stand covers.
11. Fit the cap.
12. Move the curtain up and down to check the fu nction.
Siemens-Elema AB SPB7-230.091.11 Page 11 of 18 M1000/3000/3000 Nova Solna, Sweden Rev . 01 09.00 SPS-UD Service
2 - 12 Work procedure

Exchange upper and/or lower wire wheel 2

The information written in parenthe sis are valid during the exchange of lower wire wheel. The figures explains how to exchange the upper wire wheel.
1. Follow the work procedure described in t he chapter "Dismounting", Page 2 - 1.
2. To secure the upper and lower curtains from f alling down during the exchange of upper and/or lower wire, place e.g. sc rewdrivers in suitable holes of the curtain holders and let the screwdriver s lean against the stand (Fig. 16)
Fig. 16
3. Loosen the wire wheel (1/Fig. 17).
1
Fig. 17
MAM00695
M1000/3000/3000 Nova SPB7-230.091.11 Page 12 of 18 Siemens-Elema AB Service Rev. 01 09.00 SPS-UD Solna, Sweden
Work procedure 2 - 13
4. Secure the lower (upper) wire from falli ng down e.g. with a cable tie (Fig. 18).
Fig. 18
5. Loosen the upper (lower) wire from the spri ng.
6. Exchange the upper (lower) wire wheel with t he new one.
Siemens-Elema AB SPB7-230.091.11 Page 13 of 18 M1000/3000/3000 Nova Solna, Sweden Rev . 01 09.00 SPS-UD Service
2 - 14 Work procedure
7. Make sure the wire is turned:
- 4.75 turns for the upper curtain ( 1/Fig. 9).
- 4.5 turns for the lower cu rtain (2/Fig. 9).
1
2
MAM00711
Fig. 19
8. Attach the wire to the spring.
9. Remove the securing screwdrivers.
M1000/3000/3000 Nova SPB7-230.091.11 Page 14 of 18 Siemens-Elema AB Service Rev. 01 09.00 SPS-UD Solna, Sweden
Work procedure 2 - 15
10. Tighten the wire wheel until the length of the spring is 160&5 mm (Fig. 10).
MAM00693
Fig. 20
11. Fit the stand covers.
12. Fit the cap.
13. Move the curtain up and down to check the fu nction.
Siemens-Elema AB SPB7-230.091.11 Page 15 of 18 M1000/3000/3000 Nova Solna, Sweden Rev . 01 09.00 SPS-UD Service
2 - 16 Work procedure

Exchange spring 2

1. Follow the work procedure described in t he chapter "Dismounting", Page 2 - 1.
2. To secure the upper and lower curtains from f alling down during the exchange of spring, place e.g. screwdrivers in suitable holes of the curtain holder s and let the screwdrivers lean against the stand ( Fig. 16)
Fig. 21
3. Loosen the wire wheel (1/Fig. 17).
1
Fig. 22
MAM00695
4. Exchange the spring with the new spring.
M1000/3000/3000 Nova SPB7-230.091.11 Page 16 of 18 Siemens-Elema AB Service Rev. 01 09.00 SPS-UD Solna, Sweden
Work procedure 2 - 17
5. Make sure the wire is turned:
- 4.75 turns for the upper curtai n (1/Fig. 9).
- 4.5 turns for the lower curtain (2/Fig. 9).
1
2
MAM00711
Fig. 23
6. Remove the securing screwdrivers.
Siemens-Elema AB SPB7-230.091.11 Page 17 of 18 M1000/3000/3000 Nova Solna, Sweden Rev . 01 09.00 SPS-UD Service
2 - 18 Work procedure
7. Tighten the wire wheel until the leng th of the spring is 160&5 mm (Fig. 10).
MAM00693
Fig. 24
8. Fit the stand covers.
9. Fit the cap.
10. Move the curtain up and down to check the funct ion.
M1000/3000/3000 Nova SPB7-230.091.11 Page 18 of 18 Siemens-Elema AB Service Rev. 01 09.00 SPS-UD Solna, Sweden
Loading...