Samsung VR 8559 Service Manual
VIDEO CASSETTE RECORDER
VR8559/5559/3559
SERVICE
1. Precautions
2. Alignment and Adjustment
3. Exploded View and Parts List
4. Electrical Parts List
5. Schematic Diagrams
Manual
VIDEO CASSETTE RECORDER CONTENTS
For mechanical disassembly and adjustment, refer to the “Mechanical Manual” (DX-9R AC68-00001A).
MENU
SERVICE MANUAL VR8559/5559/3559
ELECTRONICS
© Samsung Electronics Co., Ltd. DEC. 1998
Printed in Korea
AC68-00119A
IMPORTANT SERVICE GUIDE
3 MODE SWITCH (PROGRAM SWITCH) ASSEMBLY POINT
1) When installing the ass’y full deck on the Main PCB, be sure to align the assembly point of mode switch.
ASSEMBLY POINT
Fig. 1
3 HOW TO EJECT THE CASSETTE TAPE
(If the unit does not operate on condition that tape is inserted into housing ass’y)
1) Remove the Holder Worm Œ and the gear worm ´. (See Fig. 2)
2) Turn the Gear Worm Wheel ˇ counterclockwise in the direction of arrow with screw driver. (See Fig. 2)
3) When Slider S, T are approched in the position of unloading, rotate holder Clutch counterclockwise after inserting screw driver in the
hole of frame’s bottom in order to wind the unwinded tape. (Refer to Fig. 3)
(If you rotate Gear Worm Wheel continuously when tape is in state of unwinding, you may cause a tape contamination by grease and
tape damage. Be sure to wind the unwinded tape in the state of set horizently.)
4) Rotate Gear Worm Wheel ˇ counterclockwise using screw driver again up to the state of eject mode and then pick out the tape.
(Refer to Fig. 2)
Fig. 2 Fig. 3
ΠHOLDER WORM
´ GEAR WORM
SCREW DRIVER
ˇ GEAR WORM WHEEL
FRAME
Samsung Electronics 1-1
1. Precautions
1. Be sure that all of the built-in protective devices are
replaced. Restore any missing protective shields.
2. When reinstalling the chassis and its assemblies, be
sure to restore all pretective devices, including :
control knobs and compartment covers.
3. Make sure that there are no cabinet openings
through which people--particularly children
--might insert fingers and contact dangerous
voltages. Such openings include the spacing
between the picture tube and the cabinet mask,
excessively wide cabinet ventilation slots, and
improperly fitted back covers.
If the measured resistance is less than 1.0 megohm
or greater than 5.2 megohms, an abnormality exists
that must be corrected before the unit is returned
to the customer.
4. Leakage Current Hot Check (See Fig. 1-1) :
Warning : Do not use an isolation transformer
during this test. Use a leakage current tester or a
metering system that complies with American
National Standards Institute (ANSI C101.1,
Leakage Current for Appliances), and Underwriters
Laboratories (UL Publication UL1410, 59.7).
5. With the unit completely reassembled, plug the AC
line cord directly the power outlet. With the unitÕs
AC switch first in the ON position and then OFF,
measure the current between a known erath
ground (metal water pipe, conduit, etc.) and all
exposed metal parts, including : antennas, handle
brackets, metal cabinets, screwheads and control
shafts. The current measured should not exceed
0.5 milliamp. Reverse the power-plug prongs in the
AC outlet and repeat the test.
6. X-ray Limits :
The picture tube is designed to prohibit X-ray
emissions. To ensure continued X-ray protection,
replace the picture tube only with one that is the
same type as the original.
Fig. 1-1 AC Leakage Test
7. Antenna Cold Check :
With the unitÕs AC plug disconnected from the
AC source, connect an electrical jumper across the
two AC prongs. Connect one lead of the ohmmeter
to an AC prong.
Connect the other lead to the coaxial connector.
8. High Voltage Limit :
High voltage must be measured each time
servicing is done on the B+, horizontal deflection
or high voltage circuits.
Heed the high voltage limits. These include the
X-ray protection Specifications Label, and the
Product Safety and X-ray Warning Note on the
service data schematic.
9. Some semiconductor (Òsolid stateÓ) devices are
easily damaged by static electricity.
Such components are called Electrostatically
Sensitive Devices (ESDs); examples include
integrated circuits and some field-effect transistors.
The following techniques will reduce the
occurrence of component damage caused by static
electricity.
10. Immediately before handling sny semiconductor
components or assemblies, drain the electrostatic
charge from your body by touching a known
earth ground. Alternatively, wear a discharging
Wrist-strap device. (Be sure to remove it prior to
applying power--this is an electric shock
precaution.)
DEVICE
UNDER
TEST
(READING SHOULD
NOT BE ABOVE
0.5mA)
LEAKAGE
CURRENT
TESTER
EARTH
GROUND
TEST ALL
EXPOSED METER
SURFACES
ALSO TEST WITH
PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)
2-WIRE CORD
Precautions
1-2 Samsung Electronics
11. High voltage is maintained within specified limits
by close-tolerance, safety-related components and
adjustments. If the high voltage exceeds the
specified limits, check each of the special
components.
12. Design Alteration Warning :
Never alter or add to the mechanical or electrical
design of this unit. Example : Do not add
auxiliary audio or video connectors.
Such alterations might create a safety hazard.
Also, any design changes or additions will void
the manufacturerÕs warranty.
13. Hot Chassis Warning :
Some TV receiver chassis are electrically
connected directly to one conductor of the AC
power cord. If an isolation transformer is not
used, these units may be safely serviced only if
the AC power plug is inserted so that the chassis
is connected to the ground side of the AC source.
To confirm that the AC power plug is inserted
correctly, do the following : Using an AC
voltmeter, measure the voltage between the
chassis and a known earth ground. If the reading
is greater than 1.0V, remove the AC power plug,
reverse its polarity and reinsert. Re-measure the
voltage between the chassis and ground.
14. Some TV chassis are designed to operate with 85
volts AC between chassis and ground, regardless
of the AC plug polarity. These units can be safely
serviced only if an isolation transformer inserted
between the receiver and the power source.
15. Never defeat any of the B+ voltage interlocks.
Do not apply AC power to the unit (or any of its
assemblies) unless all solid-state heat sinks are
correctly installed.
16. Always connect a test instrumentÕs ground lead to
the instrument chassis ground before connecting
the positive lead; always remove the instrumentÕs
ground lead last.
17. Observe the original lead dress, especially near
the following areas : Antenna wiring, sharp
edges, and especially the AC and high voltage
power supplies. Always inspect for pinched, outof-place, or frayed wiring. Do not change the
spacing between components and the printed
circuit board. Check the AC power cord for
damage. Make sure that leads and components
do not touch thermally hot parts.
18. Picture Tube Implosion Warning :
The picture tube in this receiver employs
Òintegral implosionÓ protection. To ensure
continued implosion protection, make sure that
the replacement picture tube is the same as the
original.
19. Do not remove, install or handle the picture tube
without first putting on shatterproof goggles
equipped with side shields. Never handle the
picture tube by its neck. Some Òin-lineÓ picture
tubes are equipped with a permanently attached
deflection yoke; do not try to remove such
Òpermanently attachedÓ yokes from the picture
tube.
20. Product Safety Notice :
Some electrical and mechanical parts have special
safety-related characteristics which might not be
obvious from visual inspection. These safety
features and the protection they give might be
lost if the replacement component differs from the
original--even if the replacement is rated for
higher voltage, wattage, etc.
Components that are critical for safety are
indicated in the circuit diagram by shading,
( or ).
Use replacement components that have the same
ratings, especially for flame resistance and
dielectric strength specifications. A replacement
part that does not have the same safety
characteristics as the original might create shock,
fire or other hazards.
Samsung Electronics
2-1
2. Alignment and Adjustment
2-1 Reference
1) X-Point (Tracking center) adjustment, “Head switching adjustment” and “NVRAM option setting” can be adjusted with remote control.
2) When replacing the Micom (IC601) and NVRAM (IC603 ; EEPROM) be sure to adjust the “Head switching adjustment” and
“NVRAM option setting”.
3) When replacing the cylinder ass’y, be sure to adjust the “X-Point” and “Head switching adjustment”.
4) Among Samsung VCR remote control used for adjustment as a accessory, only the remote control that has figures buttons (0 ~ 9) is
available for all adjustment regardless of chassis.
5) How to adjustment.
- Intermittently short-circuit the test point on Main PCB with pincets to set the adjustment mode.
- If the corresponding adjustment button is pressed, the adjustment is preformed automatically.
- If the adjustment is completed, be sure to turn the power off.
2-1-1 Location of adjustment button of remote control
Fig. 2-1
SHUTTLE
V-LOCK
REPLAY F.ADV/SKIP
TV/VCR PREV.CH
R
E
C
R
E
C
.
S
P
E
E
D
L
I
N
E
I
N
A
U
D
I
O
S
E
A
R
C
H
/
E
X
I
T
C
L
E
A
R
D
I
S
P
L
A
Y
POWER EJECT
CH/TRK
VCR
TV
CABLE/DSS
ENTER
MENU
SLOW
VOL
100
X-Point (Tracking Center)
Adjustment
Head Switching Adjustment
NVRAM Option Setting
<This type of remote control can adjust.>
Remote Control for adjustment is not supplied as a Service Jig.
2-2
Samsung Electronics
Alignment and Adjustment
2-1-2 Test point location for adjustment mode setting
Fig. 2-2 Main PCB (Bottom View)
Short-Circuit
Alignment and Adjustment
Samsung Electronics
2-3
2-2 Mechanical Adjustment
Note : Refer to the Mechanical Manual ÒDX-9R (AC68-00001A)Ó for the adjustment and confirmation of
assÕy full deck.
2-2-1 The number and position of test point
Test point : TP601 (Control Pulse)
TP602 (H’D S/W -Trigger)
TP301 (Envelope)
TP302 (Audio output)
TP303 (Video output)
Fig. 2-3 Location of Test point (Main PCB-Top View)
AUDIO OUTPUT
HEAD SWITCHING
ENVELOPE
2-2-1 ACE Head Position (X-Point) Adjustment
(See the 2-2-1(d) ACE Head Position (X-Point) Adjustment
on page 2-2 of the Mechanical Manual)
1) Playback the alignment tape (Color bar).
2) Intermittently short-circuit the two test points on
Main PCB to set the adjustment mode.
(See Fig. 2-2)
3) Press the Ò5Ó button of remote control then adjustment is operated automatically. (See Fig. 2-1)
4) Connect the CH-1 probe to TP301 (Envelope) the
CH-2 probe to TP602 (HÕD switching pulse) and
then trigger to CH-1.
5) Insert the (-) driver into the X-Point adjustment
hole and adjust it so that envelope waveform is
maximum.
6) Turn the Power off.
2-4
Samsung Electronics
Alignment and Adjustment
2-3 Head Switching Point Adjustment
1) Playback the alignment tape.
2) Intermittently short-circuit the two test points on Main PCB to set the adjustment mode. (See Fig. 2-2)
3) Press the ÒREC.SPEEDÓ button of remote control then adjustment is operated automatically. (See Fig. 2-1)
4) Turn the Power off.
2-4 NVRAM Option Setting
1) Intermittently short-circuit the two test points on Main PCB to set the adjustment mode. (See Fig. 2-2)
2) Press the ÒMENUÓ button on the remote control about 5 seconds then option setting display is appeared.
(See Fig. 2-4)
3) Select the option number (See Table 2-1) of corresponding model with ÒFFÓ and ÒREWÓ button on the remote
control.
4) If selecting the option number is completed, press the ÒSTOPÓ button of remote control.
(If ÒSTOPÓ button is pressed, the selected number is changes reversed color. ; See Fig. 2-4)
5) Press the ÒMENUÓ button of remote control again to store the option number.
(ÒsaveÓ is displayed for a second as shown Fig. 2-5 and this setting is completed.)
6) Turn the Power off.
1) NVRAM Option is adjusted at production line basically.
2) In case Micom (IC601) and NVRAM (IC603 ; EEPROM) is replaced, be sure to set the corresponding option number of the repaired
model. (If the option is not set, the unit is not operated.)
MOVE :
SAVE
: MENU
01 02 03 04 05 06 07 08
09 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
25 26 27 28 29 30 31 32
33 34 35 36 37 38 39 40
Fig. 2-4
MOVE : save
SAVE
: MENU
01 02 03 04 05 06 07 08
09 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
25 26 27 28 29 30 31 32
33 34 35 36 37 38 39 40
Fig. 2-5
MODELS OPTION NUMBER
VR8559 2, 6, 7, 18, 28, 36
VR5559 6, 7, 18, 28, 36
VR3559 1, 6, 7, 18, 28, 36
<Table 2-1>
Samsung Electronics 3-1
3. Exploded View and Parts List
3-1 Cabinet Assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
3-2 Mechanical Parts (Top Side) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
3-3 Mechanical Parts (Bottom Side) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Page
3-2
3-4
3-6
Exploded View and Parts List
3-2 Samsung Electronics
3-1 Cabinet Assembly
1
21
22
S.N.A. : Service Not Available
157
153
FULL DECK (S.N.A.)
BOTTOM-COVER (S.N.A.)
TM401B
200
MAIN PCB (S.N.A.)
157
BRACKET-FRAME
(S.N.A.)
S601A
LD601A
S602A
LED PCB (S.N.A.)
CN605B
CN303B
101
155
Exploded View and Parts List
Samsung Electronics 3-3
Loc. No Parts No. Description ; Specification Remark
1 AC97-00172A ASSY-PANEL FRONT;VR8559 VR8559
AC97-00173A ASSY-PANEL FRONT;VR5559 VR5559
AC97-00174A ASSY-PANEL FRONT;VR3559 VR3559
21 AC64-52158Q DOOR-CASSETTE;VR8559 VR8559
AC64-52158R DOOR-CASSETTE;VR5559 VR5559
AC64-52158S DOOR-CASSETTE;VR3559 VR3559
22 AC61-62032A SPRING-MASK;X-9,-,SUS,-,4.4,-,SV-C130
101 AC64-30892A CABINET-TOP;X-9,SECC,PCM,0.5,
153 AC60-12126A SCREW-BH;-,BH,-,4*12,FE,FZY,-,-,155 AC60-12134A SCREW-TAP BH;-,BH,-,2-4X16,-,FE
157 AC60-10063A SCREW-TAPTITE;BH,+,-,M3,L12,ZPC3,SWRCH18
200 AC39-10200N POWER-CORD;SPT-2,AWG#18,1.8MT,WAFER,
CN303B 3809-001110 CABLE-FLAT;30V,80C,150mm,7P,1.25mm,UL289
CN605B 3809-001112 CABLE-FLAT;30V,80C,130mm,5P,1.25mm,UL289
CN6CSB 3809-001112 CABLE-FLAT;30V,80C,130mm,5P,1.25mm,UL289
LD601A AC61-21009A HOLDER-LED;-,POM(M90-44),-,BLK,-,X-9
S601A AC61-21008A HOLDER-SENSOR;-,POM(M90-44),-,BLK,-,X-9
S602A AC61-21008A HOLDER-SENSOR;-,POM(M90-44),-,BLK,-,X-9
TM401B AC61-11056J CONNECTOR BOARD-ASSY;HIPS94+ VR8559
AC61-11056K CONNECTOR BOARD-ASSY;HIPS94+ VR5559/3559
Exploded View and Parts List
3-4 Samsung Electronics
3-2 Mechanical Parts (Top Side)
G001
K250
K248
K110
K502
K350
K330
K182
K140
K490
K530
K240
G532
G420
G450
K546
G510
B410
B440
B444
B446
B448
B452
G527
G520
G480
G680
S.N.A.
S.N.A.
S.N.A.
S.N.A.
S.N.A.
G530
K340
B473
K188
G555
G546
S.N.A. : Service Not Available
S.N.A.
Exploded View and Parts List
Samsung Electronics 3-5
Loc. No Parts No. Description ; Specification Remark
B410 AC31-12016A MOTOR-LOADING ASSY;-,-,X-9
B440 AC60-10515A SCREW-MACHINE;-,PH,+,-,M3,L3,ZPC,-,YEL
B444 AC66-20571A GEAR-WORM;-,POM SW-01,0.5,2,-,4.5,X-9
B446 AC61-21005A HOLDER-WORM;-,POM M90-44,-,-,-,X-9
B448 AC66-20573A GEAR-WORM WHEEL;-,POM SW-01,0.6,11,-,6.6
B452 AC66-20575A GEAR-FL CAM;-,POM SW-01,M0.6,Z88,-,PCD58
B473 AC61-60559A SPRING-PINCH DRIVE;-,TS,SUS304,PI0.5,OD4
G001 AC96-10481K ASSY-CYLINDER;CX-9, NTSC 6HD (6HD NON-DIAMOND HEAD)
AC96-10481H ASSY-CYLINDER;CX-9, NTSC 4HD (4HD NON-DIAMOND HEAD)
AC96-10481F ASSY-CYLINDER;CX-9, NTSC 2HD (2HD NON-DIAMOND HEAD)
G420 AC66-80142A SLIDER-SUPPLY ASSY;-,X-9(TS),-,-,-,X-9
G450 AC66-80141A SLIDER-TAKE UP ASSY;-,X-9(TS),-,-,-,X-9
G480 AC33-10217H HEAD-ACE ASSY;-,-,-,-,X-9
G510 AC60-10518A SCREW-TAP TITE;-,PH,+,SW+ZW,M2.6,L5.6,ZP
G520 AC66-30539A LEVER-#9 GUIDE ASSY;-,X-9(TS),-,-,-,X-9
G527 AC61-60553A SPRING-#9 GUIDE;-,ES,SUS304-WPB,OD3.1,0.
G530 AC33-10217G HEAD-FE;VAA00000275,-,-,-,X-9
G532 AC60-10519A SCREW-TAP TITE;-,PH,+,-,M2.6,L8,ZPC
G546 AC66-30535A LEVER-FL DOOR;-,POM M90-44,-,-,BLK,X-9
G555 AC59-90403A UNIT-PINCH ASSY;X-9,G680 AC66-30557A LEVER-H/CLEANER ASSY;-,POM+URETHANE,-,- (OPTIONAL)
K110 AC66-10267A REEL-DISK S;-,POM M90-44,-,-,X-9
K140 AC66-10268A REEL-DISK T;-,POM M90-44,-,-,X-9
K182 AC66-30524A LEVER-IDLER;-,POM9044,-,-,-,K188 AC66-20577A GEAR-IDLER;-,PEBAX 7033,-,-,-,-,X-9
K240 AC66-30538A LEVER-TENSION ASSY;-,X-9(TS),-,-,-,X-9
K248 AC61-60554A SPRING-TENSION LEVER;-,ES,SUS304-WPB,OD3
K250 AC63-12029A BAND-BRAKE ASSY;-,X-9(TS),-,-,-,X-9
K330 AC66-30550A LEVER-S.BRAKE ASSY;-,POM+SUS,-,-,-,X-9
K340 AC66-30549A LEVER-T.BRAKE ASSY;-,POM+SUS,-,-,-,X-9
K350 AC61-60564A SPRING-BRAKE;-,TENSION,SWP-A,0.25,3,-,XK490 AC61-21010A HOLDER-CASS ASSY;-,SECC+POM+SUS,-,-,-,XK502 AC61-60561A SPRING-FL.LEVER-LR;-,ES,SUS304 WPB,PI2.7
K530 AC66-30546A LEVER-FL.ARM ASS’Y;-,SECC+POM+SUS,-,-,-,
K546 AC61-50658A GUIDE-CASS. DOOR;-,POM M90-44,-,-,NTR,-,
Exploded View and Parts List
3-6 Samsung Electronics
3-3 Mechanical Parts (Bottom Side)
G542
B560
B484
B458
B500
B488
B462
(OPTIONAL)
S.N.A.
S.N.A.
S.N.A.
S.N.A.
B456
K222
K200
K225
K221
B570
B238
S.N.A. : Service Not Available
Exploded View and Parts List
Samsung Electronics 3-7
Loc. No Parts No. Description ; Specification Remark
B238 AC61-50660A SLEEVE-TENSION;-,POM M90-44,-,-,ID3,-,-,
B456 AC66-20576A GEAR-JOINT 1;-,POM SW-01,M1.0,Z22,-,PCD2
B458 AC66-20574A GEAR-JOINT 2;-,POM SW-01,M1.0,Z14,-,PCD1
B462 AC60-10517A SCREW-TAP TITE;-,PH,+,-,M2.6,L5,ZPC,-,YE
B484 AC66-20580A GEAR-LOADING DRIVE;-,POM SW-01,M1.0,Z32,
B488 AC66-30543A LEVER-S LOAD ASSY;-,-,-,-,-,X-9
B500 AC66-30542A LEVER-T LOAD ASSY;-,-,-,-,-,X-9
B560 AC31-12017A MOTOR-CAPSTAN;DMVCMC07C,-,X-9
B570 AC60-10514A SCREW-CAPSTAN;-,PH,+,M2.6,L6,G542 AC66-60051A BELT-PULLEY;-,5CM-70,2 * 2,-,71.3,-,X-9
K200 AC61-21012A HOLDER-CLUTCH ASSY;-,-,-,-,-,X-9
K221 AC66-20581A GEAR-CENTER ASSY;-,POM,M=O.5,-,HIGHT T.,
K222 AC60-30306A WASHER-SLIT;-,-,ID2.1,OD5.0,T0.5,-,POLYS
K225 AC66-30547A LEVER-UP DOWN ASSY;-,POM+SUS,-,-,-,X-9
Exploded View and Parts List
3-8 Samsung Electronics
MEMO
Loc.No Part No Description ; Specification Remark Loc.No Part No Description ; Specification Remark
Samsung Electronics
4-1
- - ASSY-MAIN;X-9, NTSC S.N.A.
S.M.P.S./POWER PARTS
BD1SS1 3301-000297 CORE-FERRITE BEAD;AA,3.6x1.2x5.7mm,1400,
BD1SS2 AC27-92001M INDUCTOR;70UH-M RT BFS3565R2F,-,-,-,C1P101 2401-001730 C-AL;10uF,20%,50V,GP,TP,5x11,2.5
C1P102 2401-001545 C-AL;47uF,20%,25V,GP,TP,6.3x7mm,2.5
C1P103 2401-002036 C-AL;1uF,20%,50V,GP,TP,5x11,2.5mm
C1P104 2401-002075 C-AL;4.7uF,20%,50V,GP,TP,5x11,5
C1P108 2401-002299 C-AL;4.7uF,20%,50V,GP,TP,5x7,5
C1P110 2401-002036 C-AL;1uF,20%,50V,GP,TP,5x11,2.5mm
C1P112 2401-002075 C-AL;4.7uF,20%,50V,GP,TP,5x11,5
C1P113 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V
C1P114 2203-001724 C-CERAMIC,CHIP;4.7nF,10%,50V
C1SD11 2401-001681 C-AL;82uF,20%,200V,GP,TP,16x26,7.5m
C1SD12 2201-000930 C-CERAMIC,DISC;220pF,10%,500V,Y5P,TP,6x4
C1SR11 2401-001235 C-AL;4.7uF,20%,250V,WT,TP,10x12.5,5
C1SR12 2401-000905 C-AL;22UF,20%,16V,BP,-,6X11,2.5MM
C1SR13 2301-000176 C-FILM,PEF;18nF,5%,100V,TP,10X9X4.3X5,5m
C1SR14 2301-000417 C-FILM,PEF;24NF,5%,50V,TP,6.5X10.5X4MM,5
C1SR15 2301-000424 C-FILM,PEF;3.3nF,5%,50V,TP,5.5x7x3mm,5mm
C1SR16 2201-000930 C-CERAMIC,DISC;220pF,10%,500V,Y5P,TP,6x4
C1SS01 2201-000795 C-CERAMIC,DISC;10nF,10%,400V,Y5P,TP,15x1
C1SS02 2201-000934 C-CERAMIC,DISC;3.3nF,20%,400V,Y5U,TP,18x
C1SS03 2201-000808 C-CERAMIC,DISC;2.2nF,10%,400V,Y5U,TP,12x
C1SS04 2201-000916 C-CERAMIC,DISC;100pF,10%,400V,Y5U,TP,10x
C1SS31 2401-000385 C-AL;10uF,20%,100V,GP,TP,6.3x11,5
C1SS32 2401-001126 C-AL;330uF,20%,25V,WT,TP,10x12.5,5
C1SS33 2401-002162 C-AL;1000uF,20%,25V,WT,TP,10x20,5mm
C1SS34 2401-001126 C-AL;330uF,20%,25V,WT,TP,10x12.5,5
C1SS35 2401-003059 C-AL;1000uF,20%,16V,GP,TP,10x16,5mm
C1SS36 2401-001479 C-AL;470uF,20%,10V,GP,-,-,TP
C1SS39 2301-000129 C-FILM,PEF;100nF,5%,50V,10X9X4.3X5,5mm,T
CN1SS1 3711-000178 CONNECTOR-HEADER;1WALL,2P,1R,3.96mm,STRA
D1P101 0401-000101 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
D1P103 0402-000127 DIODE-RECTIFIER;1N4002,100V,1A,DO-41,TP
D1P104 0402-000127 DIODE-RECTIFIER;1N4002,100V,1A,DO-41,TP
D1P105 0402-000127 DIODE-RECTIFIER;1N4002,100V,1A,DO-41,TP
D1P106 0402-000127 DIODE-RECTIFIER;1N4002,100V,1A,DO-41,TP
D1P107 0402-000127 DIODE-RECTIFIER;1N4002,100V,1A,DO-41,TP
D1P108 0401-000101 DIODE-SWITCHING;1N4148,100V,200mA,DO-35, HI-FI Only
D1P109 0401-000101 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
D1SD11 0401-000101 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
D1SD31 0401-000101 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
D1SR11 0401-000101 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
D1SR31 0401-000101 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
D1SS01 0402-001196 DIODE-RECTIFIER;1T5,600V,1A,TS-1,TP
D1SS02 0402-001196 DIODE-RECTIFIER;1T5,600V,1A,TS-1,TP
D1SS03 0402-001196 DIODE-RECTIFIER;1T5,600V,1A,TS-1,TP
D1SS04 0402-001196 DIODE-RECTIFIER;1T5,600V,1A,TS-1,TP
D1SS11 0402-000276 DIODE-RECTIFIER;UF4007,1KV,1A,DO-41,TP
D1SS31 0402-001195 DIODE-RECTIFIER;F1T4,400V,1.0A,TS-1,TP
D1SS32 0402-001194 DIODE-RECTIFIER;UG2D,200V,2A,DO-204AC,TP
D1SS33 0402-000431 DIODE-RECTIFIER;FML-M02S,200V,2.5A,TO-22
F1SD01 3601-001122 FUSE-FERRULE;250V,1.6A,FA,GLASS,5.2x20mm
IC1SS1 0604-001028 PHOTO-COUPLER;TR,50-600%,250mW,DIP-4,ST
IC1SS2 AC14-12006D IC;KA431Z,TO-92,TAPING
L1P102 AC27-92001B COIL-PEAKING AXIAL;BAL04ST101K,-,-,-,L1SS01 AC29-30050C FILTER-LINE NOISE;-,20mH,0.35A,AC250V,BS
L1SS31 AC27-12001N COIL-CHOKE;10UH-15%,RA,K-30,Q80,150KHZ,L1SS32 AC27-12001N COIL-CHOKE;10UH-15%,RA,K-30,Q80,150KHZ,PT1SD1 AC26-20120L TRANS-SWITCHING;DP,230V,UL/CSA/DEMKO,EE2
Q1P101 0501-000616 TR-SMALL SIGNAL;KSC2328A-Y,NPN,1W,TO-92L
Q1P102 0501-000616 TR-SMALL SIGNAL;KSC2328A-Y,NPN,1W,TO-92L
Q1P104 0501-000398 TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T HI-FI Only
Q1P105 0501-000610 TR-SMALL SIGNAL;KSA928A-Y,PNP,1W,TO-92L,
Q1P106 0504-000116 TR-DIGITAL;KSR1001,NPN,300mW,4.7K-4.7K,T
Q1P107 0501-000616 TR-SMALL SIGNAL;KSC2328A-Y,NPN,1W,TO-92L
Q1P108 0504-000142 TR-DIGITAL;KSR2001,PNP,300mW,4.7K-4.7K,T
Q1P109 0501-000398 TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T
Q1SR11 0502-001123 TR-POWER;KTC4419,NPN,30W,TO-220,ST,10-4
Q1SR12 0501-000442 TR-SMALL SIGNAL;KTC3203-Y,NPN,400MW,T0-9
R1P101 2001-000855 R-CARBON;560ohm,5%,1/4W,AA,TP,2.4x6.4mm
R1P103 2001-000034 R-CARBON;220OHM,5%,1/4W,AA,TP,R1P104 2001-000554 R-CARBON;270ohm,5%,1/8W,AA,TP,1.8x3.2mm HI-FI Only
R1P104 2001-000325 R-CARBON;120ohm,5%,1/8W,AA,TP,1.8x3.2mm MONO Only
R1P105 2001-000273 R-CARBON;100KOHM,5%,1/8W,AA,TP,R1P106 2001-000611 R-CARBON;3.9KOHM,5%,1/4W,AA,TP,R1P107 2001-000449 R-CARBON;2.2Kohm,5%,1/8W,AA,TP,1.8x3.2m
R1P108 2001-000449 R-CARBON;2.2Kohm,5%,1/8W,AA,TP, PCB No Marking
R1P108 2007-000493 R-CHIP;2.2KOHM,5%,1/10W,DA,TP,2012 PCB “A” Marking
R1P110 2001-000362 R-CARBON;150ohm,5%,1/8W,AA,TP,1.8x3.2mm
R1SD11 2003-002117 R-METAL OXIDE(S);330Kohm,5%,1W,AA,TP,3.3
R1SD12 2001-000490 R-CARBON;200OHM,5%,1/8W,AA,TP,R1SD31 2001-000281 R-CARBON;100ohm,5%,1/8W,AA,TP,1.8x3.2mm
R1SD32 2001-000780 R-CARBON;470OHM,5%,1/8W,AA,TP,R1SR01 2002-000320 R-COMPOSITION;1.8Mohm,10%,1/2W,AA,TP,3.5
R1SR11 2003-000119 R-METAL OXIDE;0.68ohm,5%,2W,AE,TP,6x16mm
R1SR12 2003-000314 R-METAL OXIDE;47ohm,5%,2W,AE,TP,6x16mm
R1SR13 2003-000314 R-METAL OXIDE;47ohm,5%,2W,AE,TP,6x16mm
R1SR14 2001-000003 R-CARBON;330ohm,5%,1/8W,AA,TP,1.8x3.2mm
R1SR15 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,R1SS11 2003-000994 R-METAL OXIDE(S);33Kohm,5%,2W,AF,TP,3.9x
R1SS12 2003-000994 R-METAL OXIDE(S);33Kohm,5%,2W,AF,TP,3.9x
R1SS13 2003-000148 R-METAL OXIDE;100OHM,5%,2W,AE,TP,6X16MM
R1SS32 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,R1SS33 2004-000869 R-METAL;3Kohm,1%,1/8W,AA,TP,1.8x3.2mm
R1SS34 2004-000459 R-METAL;2.2Kohm,1%,1/8W,AA,TP,1.8x3.2m
VA1SS1 1405-001026 VARISTOR;470V,600A,9x7mm,TP
ZD1P01 0403-000390 DIODE-ZENER;UZP33B,33V,31.4-34.6V,1W,DOZD1P02 0403-000717 DIODE-ZENER;MTZJ5.1B,5.1V,4.94-5.2V,500m
ZD1P03 0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500
ZD1P05 0403-001211 DIODE-ZENER;MTZJ12B,12V,11.44-12.03V,500
ZD1SR1 0403-000571 DIODE-ZENER;UZP43B,43V,40-46V,1W,DO-41,T
LOGIC PARTS
C601 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
C602 2203-000222 C-CERAMIC,CHIP;100nF,20%,50V,Z5U,TP,2012
C603 2203-000716 C-CERAMIC,CHIP;3.3nF,10%,50V,X7R,TP,2012
C604 2203-001245 C-CERAMIC,CHIP;82pF,5%,50V,NPO,TP,2012,C605 2401-000913 C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m
C606 2401-000913 C-AL;22uF,20%,16V,GP,TP,5x11mm,2.5m
C607 2203-001245 C-CERAMIC,CHIP;82pF,5%,50V,NPO,TP,2012,C608 2203-001579 C-CERAMIC,CHIP;15nF,10%,50V,NPO,TP,2012,
C609 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
C610 2202-000797 C-CERAMIC,MLC-AXIAL;10NF,30%,16V,Y5P,TP,
C611 2401-000922 C-AL;22uF,20%,16V,GP,TP,5x5,5
C612 2401-002299 C-AL;4.7uF,20%,50V,GP,TP,5x7,5
C613 2203-000429 C-CERAMIC,CHIP;18pF,5%,50V,NPO,TP,2012,C614 2203-000925 C-CERAMIC,CHIP;470nF,+80-20%,50V,Y5V,TP,
C615 2202-000121 C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP
C616 2203-000260 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,2012,
C617 2202-000216 C-CERAMIC,MLC-AXIAL;.027NF,5%,50V,SL,TP,
C618 2203-000683 C-CERAMIC,CHIP;27pF,5%,50V,NPO,TP,2012,-
4. Electrical Parts List
Loc.No Part No Description ; Specification RemarkLoc.No Part No Description ; Specification Remark
4-2
Samsung Electronics
Electrical Parts List
C619 2203-000683 C-CERAMIC,CHIP;27pF,5%,50V,NPO,TP,2012,C620 2203-000389 C-CERAMIC,CHIP;15pF,5%,50V,NPO,TP,2012,C621 2203-000389 C-CERAMIC,CHIP;15pF,5%,50V,NPO,TP,2012,C622 2203-000389 C-CERAMIC,CHIP;15pF,5%,50V,NPO,TP,2012,C623 2203-000389 C-CERAMIC,CHIP;15pF,5%,50V,NPO,TP,2012,C624 2203-000389 C-CERAMIC,CHIP;15pF,5%,50V,NPO,TP,2012,C625 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V
C626 2401-001545 C-AL;47uF,20%,25V,GP,TP,6.3x7mm,2.5
C627 2202-000797 C-CERAMIC,MLC-AXIAL;10NF,30%,16V,Y5P,TP,
C628 2401-002165 C-AL;100uF,20%,16V,GP,TP,6.3x7,5
C629 2203-000260 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,2012,
C632 2202-000797 C-CERAMIC,MLC-AXIAL;10NF,30%,16V,Y5P,TP,
C634 2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5
C636 2202-000797 C-CERAMIC,MLC-AXIAL;10NF,30%,16V,Y5P,TP,
C637 2203-000260 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,2012,
C638 2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V
C640 2202-000797 C-CERAMIC,MLC-AXIAL;10NF,30%,16V,Y5P,TP,
C641 2203-000989 C-CERAMIC,CHIP;47nF,10%,50V,X7R,TP,2012,
C647 2203-000727 C-CERAMIC,CHIP;3.9nF,10%,50V,X7R,TP,2012
C648 2203-000989 C-CERAMIC,CHIP;47nF,10%,50V,X7R,TP,2012,
C650 2401-001545 C-AL;47uF,20%,25V,GP,TP,6.3x7mm,2.5
C651 2203-000260 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,2012,
C655 2203-000260 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,2012,
C656 2401-001545 C-AL;47uF,20%,25V,GP,TP,6.3x7mm,2.5
C657 2401-001545 C-AL;47uF,20%,25V,GP,TP,6.3x7mm,2.5
C658 2203-000260 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,2012,
C663 2203-000260 C-CERAMIC,CHIP;10nF,10%,50V,X7R,TP,2012,
C668 2202-000797 C-CERAMIC,MLC-AXIAL;10NF,30%,16V,Y5P,TP,
C670 2203-000222 C-CERAMIC,CHIP;100nF,20%,50V,Z5U,TP,2012
C673 2203-000444 C-CERAMIC,CHIP;1nF,10%,50V,X7R,TP,2012,C675 2203-000609 C-CERAMIC,CHIP;22nF,10%,50V,X7R,TP,2012,
CN601 AC39-20817S LEAD CONNECTOR-ASSY;DP,SMH200-02,YBH200CN604 3711-003749 CONNECTOR-HEADER;BOX,8P,2R,2mm,STRAIGHT,
CN605 3708-001163 CONNECTOR-FPC/FC/PIC;5P,1.25mm,STRAIGHT,
D602 0401-000101 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
D603 0401-000101 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
D604 0402-000127 DIODE-RECTIFIER;1N4002,100V,1A,DO-41,TP
D605 0402-000127 DIODE-RECTIFIER;1N4002,100V,1A,DO-41,TP
IC601 AC09-00001A IC-MCU;HD6433977RF-02,100P,-,-,IC602 1003-001162 IC-MOTOR DRIVER;KA3082,SIP,10PIN,25MIL,D
IC603 AC11-12001H IC-EEPROM;24LC02B/P,DIP,IC605 AC14-12001G IC;KA78L05
J007 2007-000468 R-CHIP;1KOHM,5%,1/10W,DA,TP,2012
L601 AC27-92001B COIL-PEAKING AXIAL;BAL04ST101K,-,-,-,L602 2701-000131 INDUCTOR-AXIAL;15uH,5%,2.4x3.4mm
L603 2701-000145 INDUCTOR-AXIAL;1UH,5%,2.4X3.4MM
LD601 0601-000517 LED-IR;RECTANGULA,4x6.0mm,75mW,6V,950
PT601 0604-001122 PHOTO-INTERRUPTER;TR,0.065%,150mW,DIP-4,
PT602 0604-001122 PHOTO-INTERRUPTER;TR,0.065%,150mW,DIP-4,
Q601 0501-000398 TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T
R601 2007-000282 R-CHIP;100KOHM,5%,1/10W,DA,TP,2012
R604 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,R605 2001-000515 R-CARBON;220ohm,5%,1/8W,AA,TP,1.8x3.2mm
R606 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,R608 2007-000300 R-CHIP;10KOHM,5%,1/10W,DA,TP,2012
R609 2007-000300 R-CHIP;10KOHM,5%,1/10W,DA,TP,2012
R6100 2007-000738 R-CHIP;30KOHM,5%,1/10W,DA,TP,2012
R6111 2007-000468 R-CHIP;1KOHM,5%,1/10W,DA,TP,2012
R612 2007-000468 R-CHIP;1KOHM,5%,1/10W,DA,TP,2012
R613 2001-000786 R-CARBON;47Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R6138 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,- 4H’D/HI-FI Only
R614 2007-000380 R-CHIP;13KOHM,5%,1/10W,DA,TP,2012
R6141 2007-000468 R-CHIP;1KOHM,5%,1/10W,DA,TP,2012
R6144 2001-000780 R-CARBON;470OHM,5%,1/8W,AA,TP,R615 2007-000300 R-CHIP;10KOHM,5%,1/10W,DA,TP,2012
R6150 2001-000780 R-CARBON;470OHM,5%,1/8W,AA,TP,-
R616 2007-001039 R-CHIP;56KOHM,5%,1/10W,DA,TP,2012
R620 2007-000300 R-CHIP;10KOHM,5%,1/10W,DA,TP,2012
R621 2007-001201 R-CHIP;820OHM,5%,1/10W,DA,TP,2012
R622 2001-000780 R-CARBON;470OHM,5%,1/8W,AA,TP,R623 2007-000300 R-CHIP;10KOHM,5%,1/10W,DA,TP,2012
R624 2001-000773 R-CARBON;470Kohm,5%,1/8W,AA,TP,1.8x3.2m
R625 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,R626 2007-000290 R-CHIP;100OHM,5%,1/10W,DA,TP,2012
R627 2007-000300 R-CHIP;10KOHM,5%,1/10W,DA,TP,2012
R628 2007-000468 R-CHIP;1KOHM,5%,1/10W,DA,TP,2012
R629 2007-000267 R-CHIP;1.8KOHM,5%,1/10W,DA,TP,2012
R630 2007-000468 R-CHIP;1KOHM,5%,1/10W,DA,TP,2012
R631 2001-000435 R-CARBON;1Mohm,5%,1/8W,AA,TP,1.8x3.2mm
R632 2007-000468 R-CHIP;1KOHM,5%,1/10W,DA,TP,2012
R633 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,R635 2001-000837 R-CARBON;51Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R636 2001-000837 R-CARBON;51Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R641 2007-000477 R-CHIP;1MOHM,5%,1/10W,DA,TP,2012
R643 2007-000872 R-CHIP;4.7KOHM,5%,1/10W,DA,TP,2012
R653 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,R655 2007-000300 R-CHIP;10KOHM,5%,1/10W,DA,TP,2012
R660 2007-000931 R-CHIP;470OHM,5%,1/10W,DA,TP,2012
R661 2007-000931 R-CHIP;470OHM,5%,1/10W,DA,TP,2012
R663 2001-000522 R-CARBON;22Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R664 2007-000738 R-CHIP;30KOHM,5%,1/10W,DA,TP,2012
R666 2007-000001 R-CHIP;68KOHM,5%,1/10W,DA,TP,2012
R667 2007-000468 R-CHIP;1KOHM,5%,1/10W,DA,TP,2012
R669 2007-001039 R-CHIP;56KOHM,5%,1/10W,DA,TP,2012
R671 2001-000802 R-CARBON;5.6Kohm,5%,1/8W,AA,TP,1.8x3.2m
R672 2003-000259 R-METAL OXIDE;3.9OHM,5%,2W,AE,TP,6X16MM
R673 2007-000300 R-CHIP;10KOHM,5%,1/10W,DA,TP,2012
R674 2007-000300 R-CHIP;10KOHM,5%,1/10W,DA,TP,2012
R675 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,R676 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,R677 2007-000300 R-CHIP;10KOHM,5%,1/10W,DA,TP,2012
R678 2001-000577 R-CARBON;2Kohm,5%,1/8W,AA,TP,1.8x3.2mm HI-FI Only
R679 2001-000281 R-CARBON;100ohm,5%,1/8W,AA,TP,1.8x3.2mm HI-FI Only
R680 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,R681 2007-000586 R-CHIP;22KOHM,5%,1/10W,DA,TP,2012
R682 2001-000515 R-CARBON;220ohm,5%,1/8W,AA,TP,1.8x3.2mm
R684 2001-000522 R-CARBON;22Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R685 2007-000872 R-CHIP;4.7KOHM,5%,1/10W,DA,TP,2012
R686 2007-000872 R-CHIP;4.7KOHM,5%,1/10W,DA,TP,2012
R687 2007-000872 R-CHIP;4.7KOHM,5%,1/10W,DA,TP,2012
R688 2007-000449 R-CHIP;180OHM,5%,1/10W,DA,TP,2012
R691 2001-000708 R-CARBON;39ohm,5%,1/8W,AA,TP,1.8x3.2mm
R694 2007-000221 R-CHIP;1.2KOHM,5%,1/10W,DA,TP,2012
S601 0603-001011 PHOTO-TR;NPN,35V,6V,50mA,75mW,BK
S602 0603-001011 PHOTO-TR;NPN,35V,6V,50mA,75mW,BK
SW602 AC34-20100B SWITCH-REC;-,-,X-9,SW603 AC34-20100A SWITCH-MODE;-,-,X-9,XT601 2801-001384 CRYSTAL-UNIT;14.31818MHz,30ppm,28-AAA,16
XT602 2801-003318 CRYSTAL-UNIT;32.768KHz,20ppm,28-AAP,12.5
XT603 2801-003293 CRYSTAL-UNIT;10MHz,50ppm,28-AAA,16pF,50o
AUDIO/VIDEO PARTS
C301 2203-002793 C-CERAMIC,CHIP;1uF,+80-20%,25V,Y5V,TP,20
C302 2401-002095 C-AL;47uF,20%,25V,GP,TP,6.3x5,5mm
C303 2203-000222 C-CERAMIC,CHIP;100nF,20%,50V,Z5U,TP,2012
C304 2203-001721 C-CERAMIC,CHIP;360pF,5%,50V,NPO,TP,2012,
C305 2401-001250 C-AL;4.7uF,20%,35V,GP,TP,4x5,5
C306 2203-000408 C-CERAMIC,CHIP;180pF,5%,50V,NPO,TP,2012,
C307 2203-000818 C-CERAMIC,CHIP;33pF,5%,50V,NPO,TP,2012,C308 2203-001579 C-CERAMIC,CHIP;15nF,10%,50V,NPO,TP,2012,
C309 2401-000922 C-AL;22uF,20%,16V,GP,TP,5x5,5
C310 2401-000407 C-AL;10uF,20%,16V,GP,TP,3.5x5,2.5
Loading...