Samsung SOC-320, SOC-320P User Manual
SOC-320(P)
Installing Manual
Manuel d’installation
Montageanleitung
Manuale d’installazione
Manual de instalación
Installatiehandleiding
Manual de instalação
Installationsvejledning
Installationsbruksanvisning
àÌÒÚÛ͈Ëfl ÔÓ ÛÒÚ‡ÌÓ‚ÍÂ
E
F
D
I
Es
NL
PT
DK
S
R
Important Safety Instructions
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
E E
ELECTRIC SHOCK, DO NOT
REMOVE COVER. NO USER
SERVICEABLE PARTS INSIDE.
REFER TO QUALIFIED
SERVICE PERSONNEL.
1. Make sure that the cable is plugged in securely before using.
(A loose connection may result in fire.)
2. When installing the camera on a wall or ceiling, mount it safely and
securely. (A falling camera may cause personal injury.)
3. Do not place conductive objects (e.g., screwdrivers, coins, and
metal things) or containers filled with water on top of the camera.
(Serious injury may result from fire, electric shock, or falling objects.)
4. Do not install in a sooty, dusty, or humid location.
(Doing so may cause fire or electric shock.)
5. If any unusual smells or smoke come from the unit, stop using the
product. In such case, immediately disconnect the power source and
contact the service center. (Continued use in such a condition may
cause fire or electric shock.)
This symbol indicates high voltage
is present inside. It is dangerous
to make any kind of contact with
any inside part of this product.
This symbol alerts you that
important literature concerning
operation and maintenance has
been included with this product.
6. If this product fails to operate normally, contact the store of purchase or
your nearest service center. Never disassemble or modify this product in any
way. (The manufacturer is not liable for any damage resulting from
unauthorized disassembly or repairs.)
7. When cleaning, do not spray water directly onto parts of the product. (Doing
so may cause fire or electric shock.) Wipe the surface with a dry cloth.
Never use detergents or chemical cleaners on the product, as this may result
in discoloration of surface or cause damage to the finish.
1. Do not drop objects on the product or apply strong shock to it. Keep away
from a location subject to excessive vibration or magnetic interference.
°C/
2. Do not install in a location subject to high temperature (over 50
low temperature (below -10
fire or electric shock).
3. Avoid a location which is exposed to direct sunlight, or near heat sources
such as heaters or radiators. (Neglecting to do so may result in a risk of fire).
4. If you want to relocate the already installed product, be sure to turn off the
power and then move or reinstall it.
5. Install in a well - ventilated location.
6. Remove the power plug from the outlet when there is a lightning storm.
(Neglecting to do so may cause fire or damage to the product.)
°C/14°F
), or high humidity. (Doing so may cause
122°F),
2
3
Table of Contents
A look at the SOC-320(P)
Chapter 1 Important Safety Instructions 2
Chapter 2 A look at the SOC-320(P)
E E
Introduction of the SOC-320(P) Camera 5
Chapter 3 Before Installing SOC-320(P)
Check the Contents of the Package 6
Notice for Installation & Operation 7
Introduction of the SOC-320(P) Camera
The SOC-320(P) camera uses the VPP system exclusively manufactured by Samsung
Electronics.
It is not compatible with other products and will not in conjunction with them.
The camera is easy to install, even for general users, has a built-in microphone, and uses a
Varifocal AI (Auto iris) lens to produce the desired picture.
The Auto Iris has been installed to eliminate the Color Rolling effect, and generates clear pictures without flicker at locations with different power frequencies.
Chapter 4 Installing the SOC-320(P)
Installing the SOC-320(P) 8
Chapter 5 Specifications for Outer Connector Pin
Pin arrangement for the SOC-320(P) RJ-45 connector of
Appendix SOC-320(P) Product Specification
SOC-320(P) Product SPEC 12
4
11
What is Color Rolling? Non-periodical changes in color (to red, cyan, and yellow,
Occurrence of Color Rolling. Color Rolling can occur in environmens with mechanical
What is Flicker? The Human eye can detect flickering when the contrast
What is FL Mode? Fixing the shutter speed at 1/100(NTSC) or 1/120(PAL) to
etc) due to unstable color temperature. This is caused by
the repeated flickering of mechanical fluorescent lamps
corresponding to the power frequency.
fluorescent lamps, with manual Iris installation, and with
the shutter speed set at ELC (Electronic Level Control).
repeat frequency is low. This effect is called flicker. Flicker
is serious when the vertical synchronizing frequency differs from the ON/OFF frequency of fluorescent light. This
situation occurs when using an NTSC camera at locations
where the power frequency is 50Hz and/or when using a
PALcamera at locations where the power frequency is
60Hz.
prevent flicker at locations with different power frequencies.
5
Loading...