Samsung SNV-1080R User Manual

NETWORK CAMERA

User Manual

SNV-1080R

Network Camera

User Manual

2012 Samsung Techwi n Co., Ltd. All r ights res erved.

Trad em ark

The name of thi s product is the reg istered tradema rk of Samsung Techwin C o., Ltd. Other trad emarks mention ed in this manual are t he registered trad emark of their res pective compan y.

Restriction

Samsung Techwi n Co., Ltd shall reser ve the copyrigh t of this document. U nder no circumst ances, this docu ment shall be reproduc ed, distribute d or changed, par tially or wholly, wit hout formal auth orization of Sa msung Techwin.

Disclaimer

Samsung Techwi n makes the best to ve rify the integr ity and correc tness of the conte nts in this documen t, but no formal guar antee shall be provi ded. Use of this do cument and the subs equent results sh all be entirely on the u ser’s own responsib ility. Samsung Techwi n reserves the ri ght to change the con tents of this docu ment without pri or notice.

Design an d specificat ions are subjec t to change wit hout prior not ice.

The defau lt password c an be exposed to a h acking threa d so it is recommen ded to change th e password

after in stalling the p roduct. Note that t he security a nd other relat ed issues caus ed by the unchan ged password s hall be respon sible for the user.

is the regist ered logo of Samsun g Techwin Co., Ltd.

overview

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings, Install in accordance with the manufacturer’s

instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized

plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/ accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by

the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for

long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

● OVERVIEW

English _3

overview

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT.

Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance with the installation instructions.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

4_ overview

Class construction

An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection.

Battery

Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

Disconnection Device

Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location.

When used outside of the U.S., it may be used HAR code with fittings of an approved agency is employed.

CAUTION

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

The BNC Out terminal of the product is provided for easier installation, and is not recommended for monitoring purposes. If you keep the BNC cable connected, a risk of lightening may cause damage or malfunction to the product.

Please use the input power with just one camera and other devices must not be connected.

● OVERVIEW

English _5

overview

Please read the following recommend safety precautions carefully.

Do not place this apparatus on an uneven surface. Do not install on a surface where it is exposed to direct sunlight, near

heating equipment or heavy cold area. Do not place this apparatus near conductive material. Do not attempt to service this apparatus yourself. Do not place a glass of water on the product. Do not install near any magnetic sources. Do not block any ventilation openings. Do not place heavy items on the product.

User’s Manual is a guidance book for how to use the products.

The meaning of the symbols are shown below.

Reference : In case of providing information for helping of product’s usages Notice : If there’s any possibility to occur any damages for the goods and

human caused by not following the instruction



Please read this manual for the safety before using of goods and keep it in

the safe place.

6_ overview

CONTENTS

OVERVIEW

INSTALLATION &

CONNECTION

NETWORK CONNECTION

AND SETUP

3 Important Safety Instructions 9 Product Features 9 Recomended PC Specifications 10 Recomended Micro SD/SDHC

Memory Card Specifications

10 What’s Included 11 At a Glance

13 Installation 15 Inserting/Removing an SD

Memory Card

16 Memory Card Information

(Not Included)

17 Connecting with other Device

20 Connecting the Camera Directly

to Local Area Networking

21 Connecting the Camera Directly

to a DHCP Based DSL/Cable Modem

22 Connecting the Camera Directly

to a PPPoE Modem

23 Connecting the Camera to a

Broadband Router with the PPPoE/Cable Modem

24 Buttons used in IP Installer 25 Static IP Setup 29 Dynamic IP Setup 30

Port Range Forward (Port Mapping) Setup

32 Connecting to the Camera from a

Shared Local PC

32 Connecting to the Camera from a

Remote PC via the Internet

● OVERVIEW

English _7

overview

WEB VIEWER

SETUP SCREEN

APPENDIX

33 Connecting to the Camera 34 Login 35 Installing ActiveX 36 Installing Silverlight Runtime 38 Using the Live Screen 41 Search and play by event 42 Search and play by time

44 Setup 44 Audio & Video Setup 52 Network Setup 59 Event Setup 66 System Setup

71 Specification 76 Product Overview 77 Troubleshooting 79 Open Source Announcement 80 License 83 GPL/LGPL Software License

8_ overview

PRODUCT FEATURES

• Multi-Streaming

This network camera can display videos in different resolutions and qualities simultaneously using different CODECs.

• Web Browser-based Monitoring

Using the Internet web browser to display the image in a local network environment.

• Alarm

If an event occurs, the event-related video will be transferred to the email specified by the user, or saved to the SD memory.

• Video Motion Detection

Detects a motion from the video before triggering an event.

• Face Detection

Recognizes a face from the camera input video, or transfers a clearer image of your specified area.

• Auto Detection of Disconnected Network

Detects network disconnection before triggering an event.

• ONVIF Compliance

This product supports ONVIF.

For more information, refer to www.onvif.org.

RECOMENDED PC SPECIFICATIONS

• CPU : Intel(R) Core(TM)2 2.4 GHz or higher

• Operating System : Windows XP, VISTA, 7

• Resolution : 1280X1024 pixels or higher

• RAM : 2GB or higher

• Web Browser : Internet Explorer 7.0 or later, Firefox 3.0 or later, Chrome 8.0 or later,

Safari 4.0 or later

Neither a beta test version unlike the version released in the company website nor the developer version will



be supported. It is recommended to connect to IPv6 in Windows 7.



• Video Memory : 256MB or higher



Mac OS

If the driver of the video graphic adapter is not installed properly or is not the latest version, the video may not be played properly.

For a multi-monitoring system involving at least 2 monitors, the playback performance can be deteriorated depending on the system.

● OVERVIEW

English _9

overview

RECOMENDED MICRO SD/SDHC MEMORY CARD SPECIFICATIONS

• 2GB ~ 32GB

• To ensure proper recording of video data, it is recommended you use a memory card that

supports at least read/write speed 10Mbps and Class 6.

WHAT’S INCLUDED

Please check if your camera and accessories are all included in the product package.

Appearance Item Name Quantity Description

Camera 1

User Manual,

Installer S/W CD,

CMS S/W DVD

Quick Guide 1

10_ overview

Cable for the testing monitor 1

Iron Screw 3 Used for fixing to an iron plate

L Wrench 1 Used to remove/fix the dome cover

Template

Used to test the camera connection to a

portable display device

Product installation guide

AT A GLANCE

Appearance

Item Description

Dome Cover Dome cover for the lens and unit protection.



Main unit Main unit includes the lens, switch board, PCB boards and screws.

Power Port Used to plug the power cable.

Alarm Input Port



● OVERVIEW

BROWN = Alarm IN Used to connect the alarm input sensor.

BLACK = GND Used for earth-grounding.

Network Port Used to connect a PoE or Ethernet cable.



Audio In Jack Used to connect to a microphone.



Audio Out Jack Used to connect to speakers.



English _11

overview

RESETRESET

VIDEO

OUT

Components

Item Description

Reset Button



Micro SD Memory

Card Compartment

Illumination Sensor Detects incoming light to control the IR LED.

Monitor Out



Focus lever



ZOOM lever



5 6 7

Resets the camera settings to the default. Press and hold for about 5 seconds to reboot the system.

If you reset the camera, the network settings will be adjusted so that

DHCP can be enabled. If there is no DHCP server in the network, you must run the IP Installer program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.

Compartment for the Micro SD memory card.

Using the test monitor cable, you can connect to a mobile display for camera test. (for installation)

Turn the barrel left or right to adjust the focus, and turn the knob clockwise to lock the focus.

Turn the barrel left or right to adjust the zoom, and turn the knob clockwise to lock the zoom.

IR LED These infrared LED’s are controlled by the illumination sensor.



12_ overview

installation & connection

INSTALLATION

Precautions before installation

Ensure you read out the following instructions before installing the camera:

• Select an installation site (ceiling or wall) that can endure at least 5 times of the camera

weight.

• Stuck-in or peeled-off cables can cause damage to the product or a fire.

• For safety purposes, keep anyone else away from the installation site.

And put aside personal belongings from the site, just in case.

Installing on the ceiling directly

1. Using the L-wrench provided, loosen 3 screws

by turning them counterclockwise and separate the dome cover.

2. Drill a hole (5 mm in diameter, at least 35 mm in

depth) in a desired position of the case bottom and insert the provided plastic anchor (HUD 5) to the end. Fit the bottom hole to the anchor hole and insert and tighten the ASS’Y tapping screw (TH M4×L30).

3. Connect power and video cables and arrange

cable running not to damage or squeeze them, and assemble the camera unit in the reverse way.

4. Adjust the lens aiming to your desired direction.

5. Assemble the Dome Cover.

For waterproof purpose, fix and secure the bolt using L-wrench provided.

● INSTALLATION & CONNECTION

English _13

installation & connection

Adjusting the monitoring direction for the camera

Panning

Tilting

Lens rotation

❖Adjusting the monitoring direction

You can adjust the camera direction only when the camera is fixed on the ceiling. Then, turning the camera to the left or right is referred to as “Panning”, while tilting the angle is “Tilting”. For panning, the panning limit is 177.5° for the clockwise, and 177.5° for the counterclockwise, a total of 352° enabled; further rotation is stopped by the stopper.

- Adjust the panning angle so that the camera settles in the right horizontal position. You can adjust the panning up to 177.5° in each one direction, and 177.5° in the other direction, a total of 352°.

- Adjust the tilting angle so that the camera settles in the right vertical position. You can adjust the tilting between 17° and 90°.

- The total rotation range is 351°. You can make adjustment in one direction up to 124°, and 227° in the other direction.

❖Methods of adjustment

• The case of wall installation

①

After mounting the camera on the wall, adjust the panning angle so that the camera

faces a desired direction when tilting.

②

Adjust the Rotate position to fit the video to the screen borders.

③

Then, adjust the tilting angle so that the camera faces the monitoring direction.

• The case of ceiling installation

①

After mounting the camera on the ceiling, adjust the panning angle according to the monitoring direction. You should adjust the panning angle lest that the video be displayed upside down on the monitor.

②

Adjust the Rotate position to fit the video to the screen borders.

③

Then, adjust the tilting angle so that the camera faces the monitoring direction.

For smoother Rotate adjustment, set the Tilt position between 60° ~ 80°.



0˚

17˚ ~ 90˚

14_ installation & connection

INSERTING/REMOVING AN SD MEMORY CARD

Disconnect the power cable from the camera before inserting the SD memory card.



Inserting an SD Memory Card

Push the SD memory card in the direction of the arrow shown in the diagram.

Do not insert the SD memory card while it’s upside down by force. Otherwise, it may damage the



SD memory card.

Removing an SD Memory Card

Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot.

● INSTALLATION & CONNECTION

English _15

installation & connection

Pressing too hard on the SD memory card can cause the card to shoot out uncontrollably from the



slot when released.

To remove the SD memory card, set <Record> to <Off> from <SD record> and press



[Apply (

If you have saved data in the SD memory card, removing the SD memory card prior to setting



record to OFF will cause damage to the data stored in the card.

MEMORY CARD INFORMATION (NOT INCLUDED)

What is a memory card?

The memory card is an external data storage device that has been developed to offer an entirely new way to record and share video, audio, and text data using digital devices.

Selecting a memory card that’s suitable for you

Your camera supports Micro SD/SDHC memory cards. You may, however, experience compatibility issues depending on the model and make of the memory card.

For your camera, we recommend you use a memory card from the following manufacturers: Micro SD/SDHC Memory Card : Sandisk, Transcend

Playback performance can be affected depending on the speed of memory card, so use the high-speed memory card.

)]. (page 60)

16_ installation & connection

CONNECTING WITH OTHER DEVICE

(for installation)

Power

Ethernet

Ethernet Connection

Connect the Ethernet cable to the local network or to the Internet.

Power Supply

Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the camera.

Be careful not to reverse the polarity when you connect the power cable.



You can also use a router featuring PoE (Power over Ethernet) to supply power to the camera. If both PoE and DC 12V are supplied, the product will operate with the first-applied power source.



Please make sure the monitor and camera are turned off when connecting them.



● INSTALLATION & CONNECTION

Monitor

English _17

installation & connection

Connecting to Audio Input/Output

Speaker

Microphone

Network

Microphone

Speaker

1. Connect the MIC port of the camera with the microphone directly or LINE OUT port

of the amplifier that the microphone is connected to.

2. Connect the

3. Check the specifications for audio input.

• Audio Codec

G.711 PCM. μ-law 64kbps 8kHz sampling

• Full duplex Audio

• Audio in

Used for mono signal line input (Max.2.4 Vpp)

• Audio out

Used for mono signal line output (Max.2.4 Vpp)

• Line out impedance

600

18_ installation & connection

Amp

SPEAKER port of the camera with the LINE IN port of the speaker.

Alarm input Wiring Diagram

ALARM IN

GND

(5mA sink)

To connect to the alarm input port

Connect the alarm input signal to the cable input port.

SENSOR

Port Description Port Description

ALARM IN

Alarm Input Sensor Port

GND

Earth-grounding Port

To connect the alarm input signal

Connect one strand of each signal line (2-strand) of the sensors to the [ALARM IN] port, and connect the other strand to the [GND] port.

● INSTALLATION & CONNECTION

English _19

network connection and setup

You can set up the network settings according to your network configurations.

CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING

Connecting to the camera from a local PC in the LAN

1. Launch an Internet browser on the local PC.

2. Enter the IP address of the camera in the address bar of the browser.

Camera

Firewall

INTERNET

External Remote PC

Switch

Camera

Local PC

A remote PC in an external Internet out of the LAN network may not be able to connect to the



camera installed in the intranet if the port-forwarding is not properly set or a firewall is set. In this case, to resolve the problem, contact your network administrator.

By factory default, the IP address will be assigned from the DHCP server automatically. If there is



no DHCP server available, the IP address will be set to 192.168.1.100. To change the IP address, use the IP Installer. For further details on IP Installer use, refer to “Static IP Setup”. (Page

20_ network connection and setup

DDNS Server (Data Center, KOREA)

25)

CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM

INTERNET

DDNS Server

(Data Center, KOREA)

External Remote PC

Camera

DSL/Cable

Modem

1. Use the cross LAN cable to connect the network cable directly to your PC.

2. Run the IP Installer and change the IP address of the camera so that you can use

the web browser on your desktop to connect to the Internet.

3. Use the Internet browser to connect to the camera.

4. Move to [Setup] page.

5. Move to [Network] – [DDNS] and configure the DDNS settings.

6. Move to [Network] – [Interface], and set the

IP type to [DHCP].

7. Connect the camera, which was removed from your PC, directly to the modem.

8. Restart the camera.

For registering the DDNS settings, refer to “Registering with DDNS”. (page 54)



For configuring the DDNS settings, refer to “DDNS”. (page 53)



For setting the IP type, refer to “Interface”. (page 52)



●

NETWORK CONNECTION AND SETUP

English _21

network connection and setup

CONNECTING THE CAMERA DIRECTLY TO A PPPoE MODEM

PPPoE Modem

Camera

1. Use the cross LAN cable to connect the network cable directly to your PC.

2. Run the IP Installer and change the IP address of the camera so that you can use

the web browser on your desktop to connect to the Internet.

3. Use the Internet browser to connect to the camera.

4. Move to [Setup] page.

5. Move to [Network] – [DDNS] and configure the DDNS settings.

6. Move to [Network] – [Interface], and set the

7. Connect the camera, which was removed from your PC, directly to the modem.

8. Restart the camera.

For registering the DDNS settings, refer to “Registering with DDNS”. (page 54)



For configuring the DDNS settings, refer to “DDNS”. (page 53)



For setting the IP type, refer to “Interface”. (page 52)



INTERNET

DDNS Server

(Data Center, KOREA)

External Remote PC

IP type to [PPPoE].

22_ network connection and setup

CONNECTING THE CAMERA TO A BROADBAND ROUTER WITH THE PPPoE/CABLE MODEM

This is for a small network environment such as homes, SOHO and ordinary shops.

Camera

PPPoE or

Broadband

Cable Modem

Camera

Local PC

Router

Configuring the network settings of the local PC connected to a Broadband Router

Configuring the network settings of the local PC connected to a Broadband Router, follow the instructions below.

• Select : <Network Neighborhood>  <Properties>  <Local Area Connection> <Properties>  <General>  <Internet Protocol (TCP/IP)>  <Properties> 



<Obtain an IP address automatically> or <Use the following IP address>.

• Follow the instructions below if you select <Use the following IP address>:

ex1) If the address (LAN IP) of the Broadband Router is 192.168.1.1

IP address : 192.168.1.100 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.1.1

ex2) If the address (LAN IP) of the Broadband Router is 192.168.0.1

IP address : 192.168.0.100 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.0.1

ex3) If the address (LAN IP) of the Broadband Router is 192.168.xxx.1

IP address : 192.168.xxx.100 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.xxx.1

For the address of the Broadband Router, refer to the product’s documentation.



For more information about port forwarding of the broadband router, refer to “Port Range



Forward (Port Mapping) Setup”.

(Page 30)

INTERNET

PPPoE or

Cable Modem

DDNS Server (Data Center, KOREA)

External Remote PC

●

NETWORK CONNECTION AND SETUP

English _23

network connection and setup

BUTTONS USED IN IP INSTALLER

Item Description

Device Name



Alias This function is not currently implemented.

Mode

MAC(Ethernet)



Address

IP Address



Protocol



Model name of the connected camera. Click the column to sort the list by model name. However, search will be stopped if clicked during the search.

Displays either <Static connection status.

Ethernet address for the connected camera. Click the column to sort the list by Ethernet address. However, search will be stopped if clicked during the search.

It is an IP address specified in the camera.

Click the column to sort the list by IP address. However, search will be stopped if clicked during the search. The factory default is “192.168.1.100”.

Network setting for the camera. The factory default is “IPv4”. Cameras with the IPv6 setting will be displayed “IPv6”.

>, <Dynamic> or <PPPoE> for the current network

24_ network connection and setup

Item Description

URL



IPv4 Scans for cameras with the IPv4 setting.



IPv6





Auto Set The IP Installer automatically configures the network settings.



Manual Set You should configure the network settings manually.



Exit Exits the IP Installer program.

For the IP installer, use only the installer version provided in the installation CD or use the



latest one if available. You can download the latest version from the Samsung web site (www. samsungipolis.com).

DDNS URL address enabling access from the external Internet. However, this will be replaced with the <IP Address> of the camera if DDNS registration has failed.

Scans for cameras with the IPv6 setting. Activated in an IPv6 compliant environment.

Scans for cameras that are currently connected to the network. However, this button will be grayed out if neither IPv4 nor IPv6 is checked.

STATIC IP SETUP

Manual Network Setup

Run <IP Installer_vX.XX.exe> to display the camera search list. At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.

For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not



support this function.

1. Select a camera in the search list.

Find the MAC (Ethernet) address labeled on the rear of the camera. Both the [Auto Set] and [Manual Set] buttons will be activated.

2. Click [Manual Set].

The Manual Setting dialog appears. The default values of <IP Address>, <Subnet Mask>, <Gateway>, <HTTP Port> and <VNP Port> of the camera will be displayed.

●

NETWORK CONNECTION AND SETUP

English _25

network connection and setup

3. In the <Address> pane, provide the

necessary information.

• MAC (Ethernet) Address : The MAC

(Ethernet) address of the applicable camera will be set automatically so you don't need to input it manually.

You can configure the static IP settings



only if the DHCP checkbox is unchecked.

If not using a Broadband Router

For setting <IP Address>, <Subnet Mask>, and <Gateway>, contact your network administrator.

4. In the <Port> pane, provide

necessary information.

• HTTP Port : Used to access the

camera using the Internet browser, defaulted to 80. Use the spin button to change the HTTP Port value.

• VNP Port : Used to control the video

signal transfer, defaulted to 4520.

5. Enter the password. This is the login password for the “admin” user who accesses the camera. The default password is “4321”.

The default password can be exposed to a hacking thread so it is recommended to change the



password after installing the product. Note that the security and other related issues caused by the unchanged password shall be responsible for the user.

6. Click [OK]. Manual network setup will be completed.

26_ network connection and setup

If using a Broadband Router

• IP Address : Enter an address falling in

the IP range provided by the Broadband Router. ex) 192.168.1.2~254,

192.168.0.2~254,

192.168.XXX.2~254

• Subnet Mask : The <Subnet Mask>

of the Broadband Router will be the <Subnet Mask> of the camera.

• Gateway : The <Local IP Address> of the Broadband Router will be the <Gateway> of the camera.

The settings may differ depending on the connected Broadband Router model.



For more information, refer to the user manual of the applicable router.

For more information about port forwarding of the broadband router, refer to “Port Range



Forward (Port Mapping) Setup”.

If the Broadband Router has more than one camera connected

Configure the IP related settings and the Port related settings distinctly with each other.

Category Camera #1 Camera #2

(Page 30)

●

NETWORK CONNECTION AND SETUP

IP related settings

Port related settings

If the <HTTP Port> is set other than 80, you must provide the <Port> number in the address bar



of the Internet browser before you can access the camera. ex) http://IP address : HTTP Port

IP Address Subnet Mask Gateway

HTTP Port VNP Port

http://192.168.1.100:8080

192.168.1.100

255.255.255.0

192.168.1.1

8080 4520

192.168.1.101

255.255.255.0

192.168.1.1

8081 4521

English _27

network connection and setup

Auto Network Setup

Run <IP Installer_vX.XX.exe> to display the camera search list. At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.

For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not



support this function.

1. Select a camera in the search list.

Find the MAC (Ethernet) address labeled on the rear of the camera. Both the [Auto Set] and [Manual Set] buttons will be activated.

2. Click [Auto Set].

The Auto Setting dialog appears. The <IP Address>, <Subnet Mask>, and <Gateway> will be set automatically.

3. Enter the password.

This is the login password for the “admin” user who accesses the camera. The default password is “4321”.

The default password can be exposed to



a hacking thread so it is recommended to change the password after installing the product. Note that the security and other related issues caused by the unchanged password shall be responsible for the user.

4. Click [OK].

Auto network setup will be completed.

28_ network connection and setup

DYNAMIC IP SETUP

Dynamic IP Environment Setup

• Example of the Dynamic IP environment

- If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server

- If connecting the camera directly to modem using the DHCP protocols

- If IPs are assigned by the internal DHCP server via the LAN

Checking the Dynamic IP

1. Run the IP Installer on the user’s local

machine to display cameras allocated with <Dynamic IP> addresses in the list.

2. Select a camera in the list, and click [Manual Set] to check the <Dynamic IP> of the camera. If you uncheck <DHCP>, you can change IP to <Static>.

●

NETWORK CONNECTION AND SETUP

English _29

+ 67 hidden pages