Samsung SNO-1080R User Manual

NETWORK CAMERA

User Manual

SNO-1080R

Network Camera

User Manual

Copyright

©2012 Sa msung Techwi n Co., Ltd. All r ights res erved.

Trad em ark

The name of thi s product is the reg istered tradema rk of Samsung Techwin C o., Ltd.
Other trad emarks mention ed in this manual are t he registered trad emark of their res pective compan y.

Restriction

Samsung Techwi n Co., Ltd shall reser ve the copyrigh t of this document. U nder no circumst ances, this docu ment shall
be reproduc ed, distribute d or changed, par tially or wholly, wit hout formal auth orization of Sa msung Techwin.

Disclaimer

Samsung Techwi n makes the best to ve rify the integr ity and correc tness of the conte nts in this documen t, but no
formal guar antee shall be provi ded. Use of this do cument and the subs equent results sh all be entirely on the u ser’s own
responsib ility. Samsung Techwi n reserves the ri ght to change the con tents of this docu ment without pri or notice.

Design an d specificat ions are subjec t to change wit hout prior not ice.

The defau lt password c an be exposed to a h acking threa d so it is recommen ded to change th e password

after in stalling the p roduct.
Note that t he security a nd other relat ed issues caus ed by the unchan ged password s hall be respon sible
for the user.

is the regist ered logo of Samsun g Techwin Co., Ltd.

overview

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings, Install in accordance with the manufacturer’s

instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized

plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/ accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by

the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for

long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.

● OVERVIEW

English _3

overview

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC
OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS
ON THE EQUIPMENT.

Apparatus shall not be exposed to dripping or splashing and that no objects
filled with liquids, such as vases, shall be placed on the apparatus.

To prevent injury, this apparatus must be securely attached to the Wall/ceiling
in accordance with the installation instructions.

CAUTION

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the product.

4_ overview

Class construction

An apparatus with CLASS construction shall be connected to a MAINS
socket outlet with a protective earthing connection.

Battery

Batteries(battery pack or batteries installed) shall not be exposed to excessive
heat such as sunshine, fire or the like.

Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.

Disconnection Device

Disconnect the main plug from the apparatus, if it’s defected. And please call
a repair man in your location.

When used outside of the U.S., it may be used HAR code with fittings of
an approved agency is employed.

CAUTION

These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualified to do so.

The BNC Out terminal of the product is provided for easier installation, and is
not recommended for monitoring purposes.
If you keep the BNC cable connected, a risk of lightening may cause damage
or malfunction to the product.

Please use the input power with just one camera and other devices must not
be connected.

● OVERVIEW

English _5

overview

Please read the following recommend safety precautions carefully.

Do not place this apparatus on an uneven surface.
Do not install on a surface where it is exposed to direct sunlight, near

heating equipment or heavy cold area.
Do not place this apparatus near conductive material.
Do not attempt to service this apparatus yourself.
Do not place a glass of water on the product.
Do not install near any magnetic sources.
Do not block any ventilation openings.
Do not place heavy items on the product.

User’s Manual is a guidance book for how to use the products.

The meaning of the symbols are shown below.

Reference : In case of providing information for helping of product’s usages
Notice : If there’s any possibility to occur any damages for the goods and

human caused by not following the instruction



Please read this manual for the safety before using of goods and keep it in

the safe place.

6_ overview

CONTENTS

OVERVIEW

3

INSTALLATION &

CONNECTION

15

NETWORK CONNECTION

AND SETUP

18

3 Important Safety Instructions
9 Product Features
10 Recomended PC Specifications
11 What’s Included
12 At a Glance

15 To adjust the zoom factor or

focus

16 Connecting with other Device

18 Connecting the Camera Directly

to Local Area Networking

19 Connecting the Camera Directly

to a DHCP Based DSL/Cable
Modem

20 Connecting the Camera Directly

to a PPPoE Modem

21 Connecting the Camera to a

Broadband Router with the
PPPoE/Cable Modem

22 Buttons used in IP Installer
23 Static IP Setup
27 Dynamic IP Setup
28

Port Range Forward (Port Mapping)
Setup

30 Connecting to the Camera from a

Shared Local PC

30 Connecting to the Camera from a

Remote PC via the Internet

● OVERVIEW

English _7

overview

WEB VIEWER

31

SETUP SCREEN

39

APPENDIX

65

31 Connecting to the Camera
32 Login
33 Installing ActiveX
34 Installing Silverlight Runtime
36 Using the Live Screen

39 Setup
39 Video Setup
47 Network Setup
54 Event Setup
60 System Setup

65 Specification
69 Product Overview
70 Troubleshooting
71 Open Source Announcement
72 License
75 GPL/LGPL Software License

8_ overview

PRODUCT FEATURES

• Dustproof/Waterproof (IP66)

The dustproof and waterproof design makes you feel at ease when installing the product
outdoors or exposing it to rain.

• SSNR3 (Samsung Super Noise Reduction)

The powerful DSP chip reduces the gain noise effectively to remove the time lag so that it
can provide a sharp and clear image in a low contrast scene.

• Day & Night (ICR)

It automatically detects the time change of the day to switch to a mode that is appropriate
to the current scene. In a daylight scene, it switches to the color mode for maintaining
the optimal color tones while it, at night, switches to B/W mode for identifying the low
contrast scene.

• IR mode

If the IR indicator turns on, the product switches to the IR mode for preventing an object
from being too bright, which helps you identify the object in near distance.

• Visibility: 15m

In B/W mode, the IR indicator turns on with the effective visibility of 15m at 0 Lux.

• SSDR (Samsung Super Dynamic Range)

For a scene showing a great contrast difference such as backlight scene, the product
maintains the bright areas while selectively making the dark areas brighter to balance the
overall contrast.

• Others

Other features include: SENS-UP, V-REV, H-REV, D-ZOOM, SHARPNESS, Motion
Detection, PRIVACY.

• Multi-Streaming

This network camera can display videos in different resolutions and qualities
simultaneously using different CODECs.

• Web Browser-based Monitoring

Using the Internet web browser to display the image in a local network environment.

• Alarm

If an event occurs, the event-related video will be transferred to the email specified by the
user.

• Video Motion Detection

Detects a motion from the video before triggering an event.

● OVERVIEW

English _9

overview

• Face Detection

Recognizes a face from the camera input video, or transfers a clearer image of your specified area.

• ONVIF Compliance

This product supports ONVIF.

For more information, refer to www.onvif.org.

RECOMENDED PC SPECIFICATIONS

• CPU : Intel(R) Core(TM)2 2.00 GHz or higher

• Operating System : Windows XP, VISTA, 7

• Resolution : 1280X1024 pixels or higher

1GB or higher

• RAM :

• Web Browser : Internet Explorer 7.0 or later, Firefox 3.0 or later, Chrome 8.0 or later,

Safari 4.0 or later

Neither a beta test version unlike the version released in the company website nor the developer version will



be supported.
It is recommended to connect to IPv6 in Windows 7.



• Video Memory :



J



Mac OS

128MB or higher

If the driver of the video graphic adapter is not installed properly or is not the latest version, the
video may not be played properly.

For a multi-monitoring system involving at least 2 monitors, the playback performance can be
deteriorated depending on the system.

10_ overview

WHAT’S INCLUDED

Please check if your camera and accessories are all included in the product package.

Appearance Item Name Quantity Description

Camera 1

User Manual,

Installer S/W CD,

CMS S/W DVD

Quick Guide 1

2

● OVERVIEW

Cable for the testing monitor 1

Template 1 Product installation guide

Tapping Screw 3 Used for installation on the wall or ceiling

L Wrench 1 Used to adjust the camera orientation

Sunshield 1

Sunshield Hold 1 It fixes the sunshield with the camera.

Used to test the camera connection to a

portable display device

It protects the camera from the direct

sunlight.

English _11

overview

Nඖ

Tඖ

◀F

AT A GLANCE

Front Side

Item Description

Sunshield It protects the camera from the direct sunlight.



Sunshield Hold It fixes the sunshield with the camera.

b

Zoom Lever Turn left or right to adjust the size of an object.

c

Focus Lever Turn left or right to fit the focus.



12_ overview

Item Description

Resets the camera settings to the default.
Press and hold for about 5 seconds to reboot the system.

If you reset the camera, the network settings will be adjusted so that

Reset Button



Video Output Port



IR LED These infrared LED’s are controlled by the illumination sensor.



Illumination Sensor Detects incoming light to control the IR LED.



Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have applied



M

ethanol.

J

DHCP can be enabled. If there is no DHCP server in the network, you
must run the IP Installer program to change the basic network settings
such as IP address, Subnet mask, Gateway, etc., before you can
connect to the network.

Connected to the monitor so that you can check the video from the camera.
(for installation)

● OVERVIEW

English _13

overview

Rear Side

Item Description

Power Port Used to plug the power cable.



Network Port Used to connect a PoE or Ethernet cable.

b

Alarm Input Port

c

y

e

t

i

.

h

r

t

n

a

l

f

o

i

o

o

t

P

c

e

e

r

d

n

a

n

n

w

a

o

e

c

e

g

B

r

:

a

e

t

N

i

w

o

O

o

I

V

p

T

d

e

U

e

h

t

t

A

a

f

C

R

o

N

)

I

M

R

A

L

A

(

N

)

D

N

W

G

(

E

O

L

R

U

B

B

Y

K

S

BROWN (ALARM IN) Used to connect the alarm input sensor.

SKY BULE (GND) Used for earth-grounding.

14_ overview

installation & connection

Nඖ

Tඖ

◀F

WIDE

¥

TELE

FAR

¥

NEAR

TO ADJUST THE ZOOM FACTOR OR FOCUS

1. Loosen the front cover as shown.

2. Loosen the zoom/focus lever slightly.

3. Position the zoom/focus lever to WIDE (NEAR) or TELE (FAR) as appropriate.

4. Then, tighten the zoom/focus lever to fix the adjusted position.

5. Turn the front cover to tighten it.

● INSTALLATION & CONNECTION

Nඖ

◀F

Tඖ

SNO-1080R

Front cover

Zoom Lever

¥

WIDE

TELE

¥

FAR

NEAR

To ensure seamless waterproofing, tighten up the front cover by turning it to the end.



J

When fixing the front cover, ensure that the triangle of the main body faces the triangle of the front

Focus Lever

cover.

Use the lever to adjust the zoom factor or focus, and turn the lever clockwise to fix it.



Before you can adjust the zoom factor/focus of the lens, loosen and remove the front cover.



English _15

installation & connection

CONNECTING WITH OTHER DEVICE

y

e

t

i

.

h

r

t

n

a

l

f

o

i

o

o

t

P

c

e

e

r

d

n

a

n

n

w

a

o

e

c

e

g

B

r

:

a

e

t

N

i

w

o

O

o

I

V

p

T

d

e

U

e

h

t

t

A

a

f

C

R

o

N

)

I

M

R

A

L

A

(

N

)

D

N

G

(

W

E

O

L

U

R

B

B

Y

K

S

Ethernet Connection

Connect the Ethernet cable to the local network or to the Internet.

Power Supply

Use the screwdriver to connect each line (+, –) of the power cable to the corresponding
power port of the camera.

Power

Ethernet

Be careful not to reverse the polarity when you connect the power cable.



J

You can also use a router featuring PoE (Power over Ethernet) to supply power to the camera.

If PoE and DC 12V are both applied, this camera will get supplied with power from PoE.



Please make sure the monitor and camera are turned off when connecting them.



16_ installation & connection

Alarm input Wiring Diagram

ALARM IN

1

(5mA sink)

2

GND

To connect to the alarm input port

Connect the alarm input signal to the cable input port.

N

I

)

M

R

A

L

A

(

N

)

D

N

G

(

W

E

O

L

U

R

B

B

Y

K

S

y

e

t

i

.

h

r

t

n

a

l

f

o

i

o

o

t

P

c

e

r

e

d

a

n

n

n

w

a

o

e

c

e

g

B

r

:

a

e

t

N

i

w

o

O

o

I

V

p

T

d

e

U

e

h

t

t

A

a

f

C

R

o

N

)

I

M

R

A

L

A

(

)

N

D

N

G

(

W

E

L

O

U

R

B

B

Y

K

S

SENSOR

Port Description Port Description

ALARM IN

Alarm Input Sensor Port

GND

Earth-grounding Port

To connect the alarm input signal

Connect one strand of each signal line (2-strand) of the sensors to the [ALARM IN] port,
and connect the other strand to the [GND] port.

● INSTALLATION & CONNECTION

English _17

network connection and setup

You can set up the network settings according to your network configurations.

CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA
NETWORKING

Connecting to the camera from a local PC in the LAN

1. Launch an Internet browser on the local PC.

2. Enter the IP address of the camera in the address bar of the browser.

Camera

Camera

Local PC

<Local Network>

A remote PC in an external Internet out of the LAN network may not be able to connect to the



M

camera installed in the intranet if the port-forwarding is not properly set or a firewall is set.
In this case, to resolve the problem, contact your network administrator.

By factory default, the IP address will be assigned from the DHCP server automatically. If there is



no DHCP server available, the IP address will be set to 192.168.1.100.
To change the IP address, use the IP Installer.
For further details on IP Installer use, refer to “Static IP Setup”. (Page

18_ network connection and setup

Switch

Firewall

INTERNET

External Remote PC

DDNS Server
(Data Center, KOREA)

23)

CONNECTING THE CAMERA DIRECTLY TO A DHCP
BASED DSL/CABLE MODEM

DSL/Cable

Camera

Modem

1. Use the cross LAN cable to connect the network cable directly to your PC.

2. Run the IP Installer and change the IP address of the camera so that you can use

the web browser on your desktop to connect to the Internet.

3. Use the Internet browser to connect to the camera.

4. Move to [Setup] page.

5. Move to [Network] – [DDNS] and configure the DDNS settings.

6. Move to [Network] – [Interface], and set the

7. Connect the camera, which was removed from your PC, directly to the modem.

8. Restart the camera.

For registering the DDNS settings, refer to “Registering with DDNS”. (page 49)



M

For configuring the DDNS settings, refer to “DDNS”. (page 48)



For setting the IP type, refer to “Interface”. (page 47)



INTERNET

DDNS Server

(Data Center, KOREA)

IP type to [DHCP].

External Remote PC

●

NETWORK CONNECTION AND SETUP

English _19

network connection and setup

CONNECTING THE CAMERA DIRECTLY TO A PPPoE
MODEM

PPPoE Modem

Camera

1. Use the cross LAN cable to connect the network cable directly to your PC.

2. Run the IP Installer and change the IP address of the camera so that you can use

the web browser on your desktop to connect to the Internet.

3. Use the Internet browser to connect to the camera.

4. Move to [Setup] page.

5. Move to [Network] – [DDNS] and configure the DDNS settings.

6. Move to [Network] – [Interface], and set the

7. Connect the camera, which was removed from your PC, directly to the modem.

8. Restart the camera.

For registering the DDNS settings, refer to “Registering with DDNS”. (page 49)



M

For configuring the DDNS settings, refer to “DDNS”. (page 48)



For setting the IP type, refer to “Interface”. (page 47)



INTERNET

DDNS Server

(Data Center, KOREA)

IP type to [PPPoE].

External Remote PC

20_ network connection and setup

CONNECTING THE CAMERA TO A BROADBAND ROUTER
WITH THE PPPoE/CABLE MODEM

This is for a small network environment such as homes, SOHO and ordinary shops.

Camera

●

NETWORK CONNECTION AND SETUP

INTERNET

PPPoE or

Cable Modem

DDNS Server
(Data Center, KOREA)

External Remote

PC

Local PC

Camera

Broadband

Router

PPPoE or

Cable Modem

Configuring the network settings of the local PC connected to a
Broadband Router

Configuring the network settings of the local PC connected to a Broadband Router, follow
the instructions below.

• Select : <Network Neighborhood>  <Properties>  <Local Area Connection>
<Properties>  <General>  <Internet Protocol (TCP/IP)>  <Properties> 



<Obtain an IP address automatically> or <Use the following IP address>.

• Follow the instructions below if you select <Use the following IP address>:

ex1) If the address (LAN IP) of the Broadband Router is 192.168.1.1

IP address : 192.168.1.100
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.1.1

ex2) If the address (LAN IP) of the Broadband Router is 192.168.0.1

IP address : 192.168.0.100
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.0.1

ex3) If the address (LAN IP) of the Broadband Router is 192.168.xxx.1

IP address : 192.168.xxx.100
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.xxx.1

For the address of the Broadband Router, refer to the product’s documentation.



M

For more information about port forwarding of the broadband router, refer to “Port Range



Forward (Port Mapping) Setup”.

(Page 28)

English _21

network connection and setup

BUTTONS USED IN IP INSTALLER

Item Description

Device Name



Alias This function is not currently implemented.

b

Mode

c

MAC(Ethernet)



Address

IP Address



Protocol



Model name of the connected camera.
Click the column to sort the list by model name.
However, search will be stopped if clicked during the search.

Displays either <Static> or <Dynamic> for the current network connection
status.

Ethernet address for the connected camera.
Click the column to sort the list by Ethernet address.
However, search will be stopped if clicked during the search.

It is an IP address specified in the camera.

Click the column to sort the list by IP address.
However, search will be stopped if clicked during the search.
The factory default is “192.168.1.100”.

Network setting for the camera.
The factory default is “IPv4”.
Cameras with the IPv6 setting will be displayed “IPv6”.

22_ network connection and setup

Item Description

URL



IPv4 Scans for cameras with the IPv4 setting.



IPv6



Search



Auto Set The IP Installer automatically configures the network settings.



Manual Set You should configure the network settings manually.



Exit Exits the IP Installer program.

m

For the IP installer, use only the installer version provided in the installation CD or use the



M

latest one if available. You can download the latest version from the Samsung web site (www.
samsungipolis.com).

DDNS URL address enabling access from the external Internet.
However, this will be replaced with the <IP Address> of the camera if
DDNS registration has failed.

Scans for cameras with the IPv6 setting.
Activated in an IPv6 compliant environment.

Scans for cameras that are currently connected to the network.
However, this button will be grayed out if neither IPv4 nor IPv6 is checked.

STATIC IP SETUP

Manual Network Setup

Run <IP Installer_vX.XX.exe> to display the camera search list.
At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.

For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not



M

support this function.

1. Select a camera in the search list.

Find the MAC (Ethernet) address
labeled on the rear of the camera.
Both the [Auto Set] and [Manual Set]
buttons will be activated.

2. Click [Manual Set].

The Manual Setting dialog appears.
The default values of <IP Address>,
<Subnet Mask>, <Gateway>, <HTTP Port> and <VNP Port> of the camera will
be displayed.

●

NETWORK CONNECTION AND SETUP

English _23

network connection and setup

3. In the <Address> pane, provide the

necessary information.

• MAC (Ethernet) Address : The MAC

(Ethernet) address of the applicable
camera will be set automatically so
you don't need to input it manually.

You can configure the static IP settings



M

only if the DHCP checkbox is unchecked.

If not using a Broadband Router

For setting <IP Address>, <Subnet Mask>, and <Gateway>, contact your network administrator.

4. In the <Port> pane, provide

necessary information.

• HTTP Port : Used to access the

camera using the Internet browser,
defaulted to 80. Use the spin button
to change the HTTP Port value.

• VNP Port : Used to control the video

signal transfer, defaulted to 4520.

5. Enter the password.
This is the login password for the “admin” user who accesses the camera.
The default password is “4321”.

The default password can be exposed to a hacking thread so it is recommended to change the



J

password after installing the product.
Note that the security and other related issues caused by the unchanged password shall be
responsible for the user.

6. Click [OK].
Manual network setup will be completed.

24_ network connection and setup

If using a Broadband Router

• IP Address : Enter an address falling in

the IP range provided by the Broadband
Router.
ex) 192.168.1.2~254,

192.168.0.2~254,

192.168.XXX.2~254

• Subnet Mask : The <Subnet Mask>

of the Broadband Router will be the
<Subnet Mask> of the camera.

• Gateway : The <Local IP Address> of
the Broadband Router will be the <Gateway> of the camera.

The settings may differ depending on the connected Broadband Router model.



M

For more information, refer to the user manual of the applicable router.

For more information about port forwarding of the broadband router, refer to “Port Range



Forward (Port Mapping) Setup”.

If the Broadband Router has more than one camera connected

Configure the IP related settings and the Port related settings distinctly with each other.

Category Camera #1 Camera #2

(Page 28)

●

NETWORK CONNECTION AND SETUP

IP related settings

Port related settings

If the <HTTP Port> is set other than 80, you must provide the <Port> number in the address bar



M

of the Internet browser before you can access the camera.
ex) http://IP address : HTTP Port

IP Address
Subnet Mask
Gateway

HTTP Port
VNP Port

http://192.168.1.100:8080

192.168.1.100

255.255.255.0

192.168.1.1

8080
4520

192.168.1.101

255.255.255.0

192.168.1.1

8081
4521

English _25

network connection and setup

Auto Network Setup

Run <IP Installer_vX.XX.exe> to display the camera search list.
At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.

For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not



M

support this function.

1. Select a camera in the search list.

Find the MAC (Ethernet) address
labeled on the rear of the camera.
Both the [Auto Set] and [Manual Set]
buttons will be activated.

2. Click [Auto Set].

The Auto Setting dialog appears.
The <IP Address>, <Subnet Mask>,
and <Gateway> will be set automatically.

3. Enter the password.

This is the login password for the
“admin” user who accesses the
camera. The default password is
“4321”.

The default password can be exposed to



a hacking thread so it is recommended to
change the password after installing the
product.
Note that the security and other related issues
caused by the unchanged password shall be
responsible for the user.

4. Click [OK].

Auto network setup will be completed.

26_ network connection and setup

DYNAMIC IP SETUP

Dynamic IP Environment Setup

• Example of the Dynamic IP environment

- If a Broadband Router, with cameras connected, is assigned an IP address by the
DHCP server

- If connecting the camera directly to modem using the DHCP protocols

- If IPs are assigned by the internal DHCP server via the LAN

Checking the Dynamic IP

1. Run the IP Installer on the user’s local

machine to display cameras allocated
with <Dynamic IP> addresses in the
list.

2. Select a camera in the list, and click
[Manual Set] to check the <Dynamic
IP> of the camera.
If you uncheck <DHCP>, you can
change IP to <Static>.

●

NETWORK CONNECTION AND SETUP

English _27