Samsung PS42B430P, PS50B430P User Manual

Связывайтесь с SAMSUNG по всему миру

Если у вас есть предложения или вопросы по продуктам Samsung, связывайтесь с информационным центром Samsung.

Country

RUSSIA 8-800-555-55-55 www.samsung.ru

UKRAINE 8-800-502-0000 www.samsung.ua

Customer Care Centre 

Web Site

PS42B430P PS50B430P

Плазменный

телевизор

руководство пользователя

BN68-02011F-00

удивительные возможности

Благодарим за приобретение продукта компании Samsung. Для получения более полного обслуживания зарегистрируйте свое устройство по адресу:

www.samsung.ru/club/registration

Модель_______Серийный номер_________

User Instructions

Screen Image retention



Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.

Height



The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do not install and operate there.

Heat on the top of the PDP TV



The top side of the product may be hot after long period of use as heat dissipates from the panel through the vent hole in the upper part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be prevented from touching the upper part of the product.

The product is making a ‘cracking’ noise.



A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as temperature or humidity. This is normal and not a defect of the unit.

Cell Defects



The PDP uses a panel consisting of 2,360,000(HD-level) to 6,221,000(FHD-level) pixels which require sophisticated technology to produce. However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.

Avoid operating the TV at temperatures below 5°C(41°F)



A still image displayed too long may cause permanent damage to the PDP Panel.



Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and centre of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause similar effect to the screen. Damages caused by the above effect are not covered by the Warranty.

Afterimage on the Screen.



Displaying still images from Video games and PC for longer than a certain period of time may produce partial afterimages. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

Warranty



Warranty does not cover any damage caused by image retention.

Burn-in is not covered by the warranty.

Installation



Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low temperatures, high humidity, chemical substance and where it operates continually such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.

Digital TV (DVB-T) Notice

1. Functionalities related to Digital TV(DVB) are only available in countries/areas where DVB-T (MPEG2 and MPEG4 AVC)

digital terrestrial signals are broadcasted or where you have access to a compatible DVB-C(MPEG2 and MPEG4 AAC) cable-TV service. Please check with your local dealer the possibility to receive DVB-T or DVB-C signal.

2. DVB-T is the DVB European consortium standard for the broadcast transmission of digital terrestrial television and DVB-C is that for the broadcast transmission of digital TV over cable. However, some differentiated features like EPG (Electric Program Guide), VOD (Video on Demand) and so on, are not

included in this specication. So, they cannot be supported at this moment.

3. Although this TV set meets the latest DVB-T and DVB-C standards[August,2008], the compatibility with future DVB-T digital terrestrial and DVB-C digital cable broadcasts cannot be guaranteed.

4. Some cable-TV providers may charge an additional fee for such a service and you may be required to agree to terms and

conditions of their business.

5. Some Digital TV functions might be unavailable in some countries or regions and DVB-C might not work correctly with all

providers.

6. For more information, please contact your local Samsung customer care centre.

Contact SAMSUNG WORLDWIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre. (See back cover for more informations.)

Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance.

Product design and specications may be changed without notice in order to enhance product performance.

English - 2

Contents

English

Connecting and Preparing Your TV

Checking Parts ..........................................................................4

■

Using the Stand-Base ...............................................................4

■ How to assemble the Stand-Base (depending on the model) ...4

■

Viewing the Control Panel .........................................................5

■

Viewing the Connection Panel...................................................6

■

Remote Control .........................................................................8

■

Installing Batteries in the Remote Control .................................9

■

Switching On and Off.................................................................9

■

Placing Your Television in Standby Mode .................................. 9

■

Viewing the Menus ..................................................................10

■

Using the TOOLS Button ......................................................... 10

■

Plug & Play Feature ................................................................ 11

■

Channel Control

Storing Channels ................................................................... 12

■

Managing Channels ................................................................15

■

Picture Control

Changing the Picture Settings ................................................. 17

■

Sound Control

Changing the Sound Setting ...................................................20

■

Selecting the Sound Mode ...................................................... 21

■

Function Description

Conguring the Setup Menu .................................................... 22

■

Setting the Time ......................................................................24

■

Source List / Edit Name ........................................................... 25

■

PC Display .............................................................................. 26

■

Supported Program ................................................................. 27

■

Recommendations for Use

Teletext Feature ....................................................................... 28

■

Wall Mount Kit Specications (VESA) ..................................... 29

■

Preparing before installing Wall- Mount on the wall ................30

■

Securing the TV to the Wall ..................................................... 30

■

Troubleshooting ....................................................................... 31

■

Specications ..........................................................................32

■

N O T

Symbol Press Note One-Touch Button TOOLS

English - 3

Connecting and Preparing Your TV

Checking Parts

Owner’s Instructions Remote Control/

Screws (4ea) Cover-Bottom Holder-Ring (4ea)

The ferrite core is used to shield the cable from interference. When connecting a cable, open the ferrite

core and clip it around the cable near the plug.

AAA Batteries (2ea)

Power Cord Cloth-Clean

(Refer to page 30)

Ferrite Core for Power

Cord (1ea)

Using the Stand-Base

Two or more people should carry the PDP. Never lay the PDP on the oor

because of possible damage to the screen. Always keep the PDP upright. The PDP can rotate 20 degrees in right and left directions.

Warranty Card/

Safety Guide Manual

(Not available in all locations)

-20° ~ 20°

How to assemble the Stand-Base (depending on the model)

Using the 4 screws for securing the stand base and the monitor, firmly attach the

monitor to the stand base. (The exterior of the set may be different than the picture.)

Warning

Firmly secure the stand to the TV before moving it, as the stand may fall and could cause serious injury.

Two or more people should carry the TV.

Never lay the TV on the oor because of

possible damage to the screen. Always store the TV upright.

English - 4

In case of installing your TV on the wall, close the cover (1) on the stand-base connection part using two screws for hiding.

Viewing the Control Panel

The product colour and shape may vary depending on the model.

Front Panel buttons

Touch each button to operate.

SOURCE

Toggles between all the available input sources (TV, Ext., AV, Component, HDMI1, HDMI2/DVI).

In the on-screen menu, use this button as you would use

the ENTER button on the remote control.

Press to see an on-screen menu of your TV’s features.

+ –

Press to increase or decrease the volume. In the on-screen menu, use the + – buttons as you would use the

◄ and ► buttons on the remote control.

Press to change channels. In the on-screen menu, use the

CH buttons as you would use the ▲ and ▼ buttons on

the remote control.

POWER INDICATOR

Lights up when the power is on.

(

POWER)

Press to turn the TV on and off.

REMOTE CONTROL SENSOR

Aim the remote control towards this spot on the TV.

SPEAKERS

English - 5

Viewing the Connection Panel

TV Rear Panel

Cable Television

Network

The product colour and shape may vary depending on the model.

Whenever you connect an audio or video system to your set, ensure that all elements are switched off.

When connecting an external device, match the colour of the connection terminal to the cable.

POWER IN

Connect the supplied power cord.

SERVICE 1, 2

Connector for service.

COMPONENT IN

Audio (AUDIO L/R) and video (Y/PB/PR) inputs for

Component.

EXT (RGB)

Inputs or outputs for external devices, such as VCR, DVD, video game device or video disc players.

7 HDMI IN 1, 2 (DVI)

No additional Audio connection is needed for an HDMI to

HDMI connection.

When using an HDMI/DVI cable connection, you must use

the HDMI IN 2 (DVI) jack.

What is HDMI?

Input/Output Specification

Connector

EXT

DIGITAL AUDIO OUT (OPTICAL)

Video Audio(L/R) RGB Video + Audio(L/R)

✔ ✔ ✔

Connect to a Digital Audio Component.

AUDIO OUT(AUDIO R/L)

Connect RCA audio signals from the TV to an external source,

Input Output

Only TV or DTV output

is available.

DVI AUDIO IN

DVI audio outputs for external devices.

ANT IN

75Ω Coaxial connector for Air/Cable Network.

Input/Output Specification

High Definition Multimedia interface allows the

transmission of high denition digital video data and

multiple channels of digital audio. The HDMI/DVI terminal supports DVI connection to

an extended device with the appropriate cable (not supplied). The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP (High Bandwidth Digital Copy Protection) coding feature installed, and supports multi - channel digital audio.

such as Audio equipment.

480i 480p 576i 576p 720p 1080i 1080p

HDMI/DVI 50Hz X X X O O O O

HDMI/DVI 60Hz X O X X O O O

Component O O O O O O O

English - 6

TV Side Panel

The product colour and shape may vary depending on the model.

COMMON INTERFACE Slot

Insert CI (Common Interface) card into the slot. (refer to page 23)

When not inserting CI CARD in some channels,

Scramble Signal is displayed on the screen.

The pairing information containing a telephone number,

CI CARD ID, Host ID, and other information will be displayed in about 2~3 minutes. If an error message is displayed, please contact your service provider.

When the channel information conguration has nished,

the message Updating Completed is displayed, indicating that the channel list is now updated.

Insert the CI-Card in the direction marked on it.

CAM is not supported in some countries and regions,check with your authorized dealer.

AV IN (VIDEO, AUDIO L/R)

Video and audio inputs for external devices, such as a camcorder or VCR.

English - 7

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV.

The performance of the remote control may be affected by bright light.

POWER button

(turns the TV on and off)

Selects the TV mode directly.

Number buttons for direct channel

access

Use to select on-screen menu items

Temporary sound switch-off

Volume increase

Volume decrease

Available source selection

Used to display Channel Lists on the

screen

Use to quickly select frequently used

functions.

Control the cursor in the menu

Use to see information on the current

broadcast

Use these buttons in the Channel list,

etc.

Previous channel

Next channel

Previous channel

Displays the main on-screen menu

Press to switch to your Favourite

channels.

Returns to the previous menu

Exit the on-screen menu

(

)

Electronic Program Guide (EPG)

display Digital subtitle display

Teletext Functions

Exit from the teletext display

(depending on the model)

Teletext mode selection (LIST/FLOF)

Teletext store

Teletext size

Teletext reveal

Fastext topic selection

Teletext display/mix both

teletext information and the normal broadcast

Teletext sub page

P :Teletext next page

P :Teletext previous page

Teletext index

Teletext hold

Teletext cancel

(

English - 8

Installing Batteries in the Remote Control

1. Lift the cover at the back of the remote control upward as shown in the gure.

2. Install two AAA size batteries.

Make sure to match the ‘+’ and ‘–’ ends of the batteries with the diagram inside

the compartment.

3. Close the cover.

Remove the batteries and store them in a cool, dry place if you won’t be using the

remote control for a long time.

If the remote control doesn’t work, check the following

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power outage or is the power cord unplugged?

5. Is there a special uorescent light or neon sign nearby?

Switching On and Off

The mains lead is attached to the rear of your set.

1. Plug the mains lead into an appropriate socket.

The standby indicator lights up on your set.

2. Press the POWERP button on your set.

You also can press the POWERP button or the TV button on the remote control to turn the TV on. The programme that you were watching last is reselected automatically.

3. Press the numeric button (0~9) or channel up / down (< / >) button on the remote control or < CH > button on your set.

When you switch the set on for the very rst time, you will be asked to choose language in which the menus are to be displayed.

4. To switch your set off, press the POWERP button again.

Placing Your Television in Standby Mode

Your set can be placed in standby mode in order to reduce the power consumption. The standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).

1. Press the POWERP button on the remote control.

The screen is turned off and a red standby indicator appears on your set.

2. To switch your set back on, simply press the POWERP, numeric buttons (0~9), TV button or channel up / down (< / >) button again.

Do not leave your set in standby mode for long periods of time (when you are away on holiday, for example). It is best to unplug the set from the mains and aerial.

English - 9

Viewing the Menus

1. With the power on, press the MENU button. The main menu appears on the screen. The menu’s left side has icons: Picture, Sound, Channel, Setup, Input, Support.

2. Press the ▲ or ▼ button to select one of the icons. Then press the ENTERE button

to access the icon’s sub-menu.

3. Press the EXIT button to exit.

The on-screen menus disappear from the screen after about one minute.

Picture

Mode : Standard

Cell Light : 4

Contrast : 95

Brightness : 45

Sharpness : 50

Colour : 50

Tint (G/R) : G50/R50

Using the TOOLS Button

You can use the TOOLS button to select your frequently used functions quickly and easily. The Tools menu changes depending on which external input mode you are viewing.

1. Press the TOOLS button. The Tools menu will appear.

2. Press the ▲ or ▼ button to select a menu, then press the ENTERE button.

3. Press the ▲ / ▼ / ◄ / ► / ENTERE buttons to display, change, or use the selected

items. For a more detailed description of each function, refer to the corresponding page.

Picture Mode, see page 17

•

Sound Mode, see page 20

•

Sleep Timer, see page 24

•

Energy Saving, see page 23

• Add to Favourite (or Delete from Favourite), see page 15

•

Picture Mode ◄ Standard ►

Sound Mode : Custom

Sleep Timer : Off

Energy Saving : Off

Add to Favourite

Tools

English - 10

Move E Enter e Exit

Plug & Play Feature

When the TV is initially powered on, basic settings proceed automatically and subsequently.

The Screen Saver is activated if there is no remote control key input for longer than 1 minute while Plug & Play is running.

The Screen Saver is activated if there is no operating signal for longer than 15 minutes.

1. Press the POWER button on the remote control. You can set the menu language.

menu is automatically displayed. Select the appropriate language by pressing the ▲ or ▼ button.

Press the ENTER

button to conrm your choice.

2. Press the ◄ or ► button to select Store Demo or Home Use, then the ENTER

You can set the menu language.

Menu Language :

button.

We recommend setting the TV to Home Use mode for the best picture in your

home environment. Store Demo mode is only intended for use in retail environments.

If the unit is accidentally set to Store Demo mode and you want to return to Home Use (Standard): Press the Volume button on

the TV. When the volume OSD is displayed, press and hold the MENU button on the TV for 5 seconds.

3. Press the ENTERE button. Select the appropriate country by pressing the ▲ or ▼ button. Press the ENTERE button to conrm

your choice.

4. Press the ▲ or ▼ button to memorize the channels of the selected connection, then press the ENTERE button.

Air: Air antenna signal.

• Cable: Cable antenna signal.

•

5. Press the ▲ or ▼ button to select the channel source to memorize. Press the ENTER

Digital & Analogue: Digital and Analogue channels.

• Digital: Digital channels.

• Analogue: Analogue channels.ogue channels.e channels.

•

For more detailed description of selecting Cable mode,, refer to page 12.

The channel search will start and end automatically.

Press the ENTER

After all the available channels are stored, the message Set the Clock Mode. is displayed.

button at any time to interrupt the memorization process.

button to select Start.

6. Press the ENTERE button. Press the ▲ or ▼ button to select Auto, then Press the ENTERE button.

If you select Manual, Set current date and time is displayed. (refer to page 24)

If you have received a digital signal, the time will be set automatically. If not, see page 24 to set the clock.

7. The brief instruction on How to get the best performance from your new HDTV. is displayed. Press the ENTERE button.

This menu is available HD Connection Guide in the Support menu.

8. The message Enjoy your TV. is displayed. When you have nished, press the ENTER

button.

Plug & Play

Nederlands

English

Eesti

Move E Enter

▲

▼

If you want to reset this feature...

1. Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup,

then press the ENTER

2. Press the ENTER

button.

button again to select Plug & Play.

3. Enter your 4 digit PIN number. The default PIN number of a new TV set is

‘0-0-0-0’.

If you want to change PIN number, refer to 22 page.

The Plug & Play feature is only available in the TV mode.

English - 11

Setup

Plug & Play  

Language : English

Time

Game Mode : Off

Child Lock : On

Change PIN

Parental Lock

Channel Control

Storing Channels

Country

❑

Digital Channel: You can change the country for digital channels.



Analogue Channel: You can change the country for analogue channels.



The PIN number input screen appears. Enter your 4 digit PIN number.

Auto Store

❑

Scans for all channels with active broadcast stations (and availability depends on your

country) and stores them in the TV's memory.

You can memorize the channels of the selected connection.

Air: Air antenna signal.

• Cable: Cable antenna signal.

• When selecting Cable,

Search Mode: Displays the search mode. (Quick)

•

Network ID: Displays the network identication code.

Frequency: Displays the frequency for the channel.

Modulation: Displays available modulation values.

Symbol Rate: Displays available symbol rates.

Search Mode: Displays the search mode. (Full, Network)

•

Frequency (Start ~ Stop) : Displays the frequency for the channel.

Modulation: Displays available modulation values.

Symbol Rate : Displays available symbol rates.

You can memorize the Channel source

Digital & Analogue: Digital and Analogue channels.

• Digital: Digital channels.

• Analogue: Analogue channels.

• If you want to stop Auto Store, press the ENTER

The Stop Auto Store? message will be displayed.

Select Yes by pressing the ◄ or ► button, then press the ENTER

If a channel is locked using the Child Lock function, the PIN input window appears.

button.

Channel

Country

Auto Store

Manual Store

Cable Search Options

Now & Next Guide

Full Guide

Default Guide : Now/Next

 

English - 12

Manual Store

❑

Scans for a channel manually and stores it in the TV’s memory.

Digital Channel



(DTV)

Manual store for digital channels.

Digital Channel is only available in DTV mode.

Channel: Set the Channel number using the ▲, ▼ or number (0~9) buttons.

•

Frequency: Set the frequency using the number buttons.

• Bandwidth: Set the bandwidth using the ▲, ▼ or number (0~9) buttons.

•

When it has nished, channels are updated in the channel list.

Analogue Channel



Manual store for analogue channel.

Programme (Programme number to be assigned to a channel): Sets the programme number using the ▲, ▼ or number (0~9)

• buttons.

 / PAL / SECAM / NTSC4.43: Sets the colour system value using the ▲ or ▼ button.

• Sound System → BG / L / I / DK: Sets the sound system value using the ▲ or ▼ button.

• Channel (When you know the number of the channel to be stored): Press the ▲ or ▼ button to select C (Air channel) or

• S (Cable channel). Press the ► button, then press the ▲, ▼ or number (0~9) buttons to select the required number.

You can also select the channel number directly by pressing the number (0~9) buttons.

If there is abnormal sound or no sound, reselect the sound standard required.

Search (When you do not know the channel numbers): Press the ▲ or ▼ button to start the search. The tuner scans the

•

frequency range until the rst channel or the channel that you selected is received on the screen.

Store (When you store the channel and associated programme number): Set to OK by pressing the ENTER

•

Channel mode

C (Air channel mode): You can select a channel by entering the assigned number to each air broadcasting station in this

button.

mode. S (Cable channel mode): You can select a channel by entering the assigned number for each cable channel in this mode.

Cable Search Options (Cable)

❑

You can add directly the channel search range in the network search mode.(Depending on the each country)

Frequency (Start ~ Stop): Displays the frequency for the channel.

• Modulation: Displays available modulation values.

• Symbol Rate: Displays available symbol rates.

• Set the Frequency (Start~Stop) and Symbol Rate using the number (0~9) buttons.

Now & Next Guide / Full Guide

❑

The EPG (Electronic Programme Guide) information is provided by the broadcasters. Programme entries may appear blank or out of date as a result of the information broadcast on a given channel. The display will dynamically update as soon as new information becomes available.

Now & Next Guide: For the six channels indicated in the left-hand column, displays the Current programme and the Next



programme information.

Full Guide: Displays the programme information as time ordered One hour segments. One hours of programme information



is displayed which may be scrolled forwards or backwards in time.

English - 13

Default Guide

❑

Now/Next / Full Guide:



You can decide whether to display either the Now/Next or

the Full Guide when the GUIDE button on the remote control is pressed.

You can also display the guide menu simply by pressing the GUIDE button.

Using the Now & Next Guide / Full Guide

Now & Next Guide

900 f tn 901 ITV Play

902 Kerrang!

903 Kiss 903 oneword

903 Smash Hits!

▼

DTV Cable 900 f tn 2:10 Tue 1 Jun Freshmen On Campus 2:00 - 2:30

No Detailed Information

Now Next

Freshmen O..

Street Hypn..

INFO

Information

No Information

Kisstory

No Information



Full Guide Exit

Mint Extra

Loaded

Fresh 40 with Dynamite MC The Distillery

Smash Hits! Sunday

Watch

Select a programme by pressing the ▲/▼/◄/► button.

▲ / ▼ / ◄ / ►

(ENTER)

If the next progrmme is selected, it is scheduled with the clock icon displayed. If the ENTERE button is

pressed again, press the ▲/▼/◄/► button to select Cancel Schedules, the scheduling is canceled with the clock icon gone. For details about scheduling programmes, refer to the section.

RED Toggle between the Now/Next or Full Guide.

GREEN

YELLOW

Full Guide: Scroll backwards quickly (-24 hours).

Mini Guide: Display next page quickly.

Full Guide: Scroll forwards quickly (+24 hours).

Mini Guide: Display previous page quickly.

BLUE Exit the guide.

INFO button for the detailed information. Channel Number, Running Time, Status Bar, Parental Level, Video

INFO

Quality Information (HD/SD), Sound Modes, Subtitle or Teletext, languages of Subtitle or Teletext and brief

summary of the highlighted programme are included on the detailed information. “…” will be appeared if the summary is long.

Full Guide

900 f tn 901 ITV Play

902 Kerrang!

903 Kiss 903 oneword

903 Smash Hits!

▼

DTV Cable 900 f tn 2:10 Tue 1 Jun Freshmen On Campus 2:00 - 2:30

No Detailed Information

Today 2:00 - 3:00 3:00 - 4:00

Freshmen O..

Street Hypn..

Mint Extra

Loaded

Fresh 40 with Dynamite MC The Distillery

Smash Hits! Sunday

INFO

Watch

Information



Now/Next +24 Hours Exit

No Information

Kisstory

No Information

Now & Next Guide

Full Guide

Channel

Default Guide : Now/Next 

Channel List

Channel Mode : Added Ch.

Fine Tune

Channel List

❑

For the detailed procedures on using the Channel List, refer to the descriptions on pages 15~16.

Channel Mode

❑

When the P </> button is pressed, Channels will be switched within the selected channel list.

Added Ch.: Channels will be switched within the memorized channel list.



Favourite Ch.: Channels will be switched within the favourite channel list.



Fine Tune (only analogue channels)

❑

If the reception is clear, you do not have to ne tune the channel, as this is done automatically during the search and store operation. If the signal is weak or distorted, you may have to ne tune the channel manually.

Fine tuned channels that have been saved are marked with an asterisk * on the right-hand side of the channel number in the

channel banner.

If you do not store the ne-tuned channel in memory, adjustments are not saved.

To reset the ne-tuning, select Reset by pressing the ▼ button and then press the ENTER

English - 14

button.

Managing Channels

Using this menu, you can Add / Delete or set Favourite channels and use the programme

guide for digital broadcasts.

Select a channel in the All Channels, Added Channels, Favourites, or Programmed screen by pressing the ▲ or ▼ buttons, and pressing the ENTERE button. Then you

can watch the selected channel.

All Channels: Shows all currently available channels.Shows all currently available channels.

•

Added Channels: Shows all added channels.Shows all added channels.

•

Favourites: Shows all favourite channels.Shows all favourite channels.

•

Programmed: Shows all current reserved programmes.Shows all current reserved programmes.

•

Using the Colour buttons with the Channel List

Red (Channel Type): Toggle between your TV, Radio, Data/Other and All.

Green (Zoom): Enlarges or shrinks a channel number.

Yellow (Select): Selects multiple channel lists.

TOOLS (Tools): Displays the Delete (or Add), Add to Favourite (or Delete from

Favourite), Timer Viewing, Edit Channel Name, Edit Channel Number, Sort, Lock (or Unlock), Select All (or Deselect All), or Auto Store menu.

(The Options menus may differ depending on the situation.)

Channel Status Display Icons

An Analogue channel.

A channel set as a Favourite.

♥

A locked channel.

Press the CH LIST button on the remote control to bring up the channel lists.

A channel selected by pressing the yellow button.

(

A programme currently being broadcast.

)

A reserved programme

Full Guide

Default Guide : Now/Next

Channel

Channel List

Channel Mode : Added Ch.

Fine Tune

824 UKTV Gold

Added Channels

825 UKTV style

A 1 C --

A 2 C A 3 ♥ C A 4 C A 5 C A 6 C A 7 C A 8 C

All



Channel Type

Zoom

Select

Tools

Channel List Tools Menu (in All Channels / Added Channels / Favourites)

❑

Press the TOOLS button to use the tools menu.

Option menu items may differ depending on the channel status.

Add / Delete



You can delete or add a channel to display the channels you want.

All deleted channels will be shown on All Channels menu.

A gray-coloured channel indicates the channel has been deleted.

The Add menu only appears for deleted channels.

You can also delete a channel to the Added Channels or Favourite menu in the

same manner.

Add to Favourite / Delete from Favourite



You can set channels you watch frequently as favourites.

Press the TOOLS button to display Tools menu.

You can also add the favourite channel by selecting Tools →→ Add to Favourite (or Delete from Favourite).

The “♥” symbol will be displayed and the channel will be set as a favourite.

All favourite channels will be shown on Favourite menu.

To select the Favourite channels you have set up, press the FAV.CH button on the

remote control.

All Channels

All

824 UKTV Gold

825 UKTV style

A 1 C --

A 2 C

A 3 C

A 4 C

A 5 C

A 6 C

A 7 C

A 8 C



Channel Type

Delete

Add to Favourite

Timer Viewing

Edit Channel Name

Sort

Lock

Zoom

Select

Continued...

▼

Tools

English - 15

Timer Viewing



If you reserve a programme you want to watch, the channel is automatically switched to the reserved channel in the Channel List; even when you are watching another channel. To reserve a programme set the current time rst. (See page 24)

Only memorized channels can be reserved.

You can set the channel, date, or start time directly by pressing the number buttons on the remote control.

Reserving a programme will be shown on Programmed menu.

Digital Programme Guide and Viewing Reservation

When a digital channel is selected, and you press the ► button, the Programme Guide for the channel appears. You can reserve a programme according to the procedures described above.

Edit Channel Name (only analogue channel)



Channels can labeled so that their call letters appear whenever the channel is selected.

The names of digital broadcasting channels are automatically assigned and cannot be labeled.

Edit Channel NumberNumber (only digital channel)



You can also edit the channel number by pressing the number buttons on the remote control.

Sort (only analogue channel)



This operation allows you to change the programme numbers of the stored channels. This operation may be necessary after using the auto store.



Lock / Unlock

You can lock a channel so that the channel cannot be selected and viewed. This function is available only when the Child Lock is set to on. (see page 22)

The PIN number input screen appears. Enter your 4 digit PIN number.

The default PIN number of a new TV set is ‘0-0-0-0’. You can change the PIN, by selecting Change PIN from the menu. The “\” symbol will be displayed and the channel will be locked.

Select All / Deselect All



Select All: You can select all the channels in the channel list.

•

Deselect All: You can deselect all the selected channels in the channel list.

•

You can perform the add / delete, add to Favourites / delete from Favourites, or lock / unlock function for multiple channels at

the same time. Select the required channels and press the yellow button to set all the selected channels at the same time.

The “c” mark appears to the left of the selected channels.

You can only select Deselect All when there is a selected channel.

Auto Store



For further details on setting up options, refer to page 12.

If a channel is locked using the Child Lock function, the PIN input window appears.

Channel List Tools Menu (in Programmed)

❑

You can view, modify or delete a reservation.

Press the TOOLS button to use the tools menu.

Change Info: Select to change a viewing reservation.

•

Cancel Schedules: Select to cancel a viewing reservation.

•

Information: Select to view a viewing reservation. (You can also change the

•

reservation information.) Select All / Deselect All : You can select (or deselect) all channels in the channel list.

•

Programmed

1 / 1 / 2009



Zoom

Change Info

Cancel Schedules

Information

Select All

Select

13:59 5 TV1 Quincy, M.E

18:59 2 TV3 The Equalizer

20:59 2 TV3 McMillan & Wife

21:59 2 TV3 M.Spillane’s mike Hammer

All

Tools Information

English - 16

Picture Control

Changing the Picture Settings

Mode

❑

You can select the type of picture which best corresponds to your viewing requirements.

Dynamic: Selects a high-denition picture for bright environments.

•

Standard: Selects the optimal picture display for normal environments.

•

Movie: Selects a comfortable picture display for dark environments.

•

Press the TOOLS button to display Tools menu. You can also set the picture mode by selecting .

Cell Light / Contrast / Brightness / Sharpness / Colour / Tint (G/R)

❑

Your television has several setting options that allow you to control the picture quality.

Cell Light: Adjusts the pixel brightness.

•

Contrast: Adjusts the contrast level.

•

Brightness: Adjusts the brightness level.

•

Sharpness: Adjusts the sharpness.

•

Colour: Adjusts the colour saturation of the picture using the bar on the screen.

•

Tint (G/R): The closer to Red 100, the more saturated the red colour becomes.

•

Select a picture mode to be adjusted rst. The adjusted values are saved for each picture mode.

When you make changes to Cell Light, Contrast, Brightness, Sharpness, Colour or Tint (G/R), the OSD will be adjusted

accordingly.

In Analogue TV, Ext., AV modes of the PAL system, you cannot use the Tint Function.

Settings can be adjusted and stored for each external device you have connected to an input of the TV.

The energy consumed during use can be signicantly reduced if the level of brightness of the picture is reduced, and then this

will reduce the overall running cost.

Picture

Mode : Standard

Cell Light : 4

Contrast : 95

Brightness : 45

Sharpness : 50

Colour : 50

Tint (G/R) : G50/R50



Advanced Settings

❑

Samsung’s new TVs allow you to make even more precise picture settings than previous models. See below to adjust detailed picture settings.

Advanced Settings is available in Standard or Movie mode.

   Off / Dark / Darker / Darkest



You can select the black level on the screen to adjust the screen depth.

   Off / Low / Medium / High



Colour : 50

Tint (G/R) : G50/R50

Picture

  

Picture Options

Picture Reset

You can adjust the screen contrast so that the optimal contrast is provided.

Gamma



You can adjust the primary colour (Red, Green, Blue) Intensity.

Colour Space



Colour Space is a colour matrix composed of red, green and blue colours. Select your favourite Colour Space to experience the

most natural colour.

Auto: Automatically sets the colour range depending on the input video source.

•

Native: Sets a colour range wider than that of the input video source.

•

White Balance



You can adjust the colour temperature for more natural picture colours.

R-Offset / G-Offset / B-Offset / R-Gain / G-Gain / B-Gain: Changing the adjustment value will refresh the adjusted screen.

•

Reset: Resets the default white balance.

•

Flesh Tone



You can emphasize the pink esh tone in the picture.

Changing the adjustment value will refresh the adjusted screen.

       Off / On



You can emphasize object boundaries in the picture.

English - 17

Picture Options

❑

Colour Tone Cool / Normal / Warm1 / Warm2



You can select the most comfortable colour tone to your eyes.

The adjusted values are stored according to the selected Picture mode.

Warm1 or Warm2 is only activated when the picture mode is Movie.

Size



Tint (G/R) : G50/R50

Advanced Settings

Picture

  

Picture Reset

You can select the picture size which best corresponds to your viewing requirements.

Auto Wide: Sets the picture in Auto Wide format.

•

16:9: Sets the picture to the 16:9 aspect ratio.

•

Wide Zoom: Select this menu to view 4:3 aspect ratio pictures over a 16:9 aspect ratio TV by stretching the 4:3 picture

•

vertically.

Zoom: Stretches the 16:9 aspect ratio picture vertical

•

4:3: Sets the picture to the 4:3 aspect ratio.

•

Screen Fit: Displays the full native HD signal that cannot be viewed using a normal TV.

•

The picture size options may vary depending on the input source.

The items available may differ depending on the selected mode.

Settings can be adjusted and stored for each external device you have connected to an input of the TV.

Temporary image retention may occur when viewing a static image on the set for more than two hours.

Wide Zoom: Press the ► button to select Position, then press the ENTERE button.

Press the ▲ or ▼ button to move the screen up / down. Then press the ENTERE button. Zoom: Press the ► button to select Position, then press the ENTERE button. Press the ▲ or ▼ button to move the picture

up and down. Then press the ENTERE button. Press the ► button to select Size, then press the ENTERE button.

Press the ▲ or ▼ button to magnify or reduce the picture size in the vertical direction. Then press the ENTERE button. After selecting Screen Fit in HDMI (1080i / 1080p) or Component (1080i / 1080p) mode: Select Position by pressing

the ◄ or ►button. Use the ▲, ▼, ◄ or ► button to move the picture. Reset: Press the ◄ or ► button to select Reset, then press the ENTERE button. You can initialize the setting.

If you use the Screen Fit function with HDMI 720p input, 1 line will be cut at the top, bottom, left and right as in the overscan

function.

Screen Mode



When setting the picture size to Auto Wide in a 16:9 wide TV, you can determine the picture size you want to see the 4:3 WSS (Wide Screen Service) image or nothing. Each individual European country requires different picture size so this function is

intended for users to select it.

16:9: Sets the picture to the 16:9 aspect ratio.

•

Wide Zoom: Select this menu to view 4:3 aspect ratio pictures over a 16:9 aspect ratio TV by stretching the 4:3 picture

•

vertically.

Zoom: Stretches the 16:9 aspect ratio picture vertically.

•

4:3: Selects the screen mode as 4:3

•

This function is available in Auto Wide mode.

This function is not available in, Component or HDMI mode.

Digital NR Off / Low / Medium / High / Auto



If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help reduce any static

and ghosting that may appear on the screen.

When the signal is weak, select one of the other options until the best picture is displayed.



HDMI Black Level Normal / Low You can directly select the black level on the screen to adjust the screen depth.

This function is active only when the external input connects to HDMI (RGB signals).

English - 18

Continued...

Film Mode



You can optimize the picture mode for watching movies.

Off : Basic video image processing applied and No auto-detection for lm-based programs.

•

Auto: Automatically adjusts for the best image quality between lm and video programs.

•

Screen Burn Protection



Congures the Screen Burn Protection Options to prevent and reduce pixel burn.

When an image remains in one position too long, it may cause a permanent burn on the screen.

Pixel Shift: To reduce the possibility of screen burn, this unit is equipped with screen burn prevention technology. This

•

technology enables you to set picture movement up/down (Vertical) and side to side (Horizontal). The Time setting allows you to program the time between movement of the picture in minutes.

Set Pixel Shift to On by pressing the ▲ or ▼ button, then press the ENTERE button.

Select the required option by pressing the ▲ or ▼ button, then press the ENTERE button.

Available options: Horizontal, Vertical, Time.

Optimum condition for pixel shift

Item TV / Ext / AV/ / Component / HDMI

Horizontal 0~4 2

Vertical 0~4 2

Time (minute) 1~4 min 3 min

The Pixel Shift value may differ depending on the monitor size (inches) and mode.

This function is not available in the Screen Fit mode.

Scrolling: This function helps remove after images on the screen by moving all the pixels on the PDP according to a pattern

•

Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image

on the screen for a long time. Side Grey: When you watch TV with the screen ratio of 4:3, the screen is prevented from any damage by adjusting the white

•

balance on both extreme left and right sides.

Dark: When you set the screen ratio to 4:3, it darkens the left and right sides.

Light: When you set the screen ratio to 4:3, it brightens the left and right sides.

/ Cancel

❑

Resets all picture settings to the default values.

Select a picture mode to be reset. The reset is performed for each picture mode.

Advanced Settings

Picture Options

Picture

Picture Reset ►

English - 19

Sound Control

Changing the Sound Setting

/ Music / Movie / Clear Voice / Custom

❑

You can select the type of special sound effect to be used when watching a given broadcast.

Press the TOOLS button to display Tools menu.

You can also congure the sound mode by selecting Tools → Sound Mode.

Equalizer

❑

The sound settings can be adjusted to suit your personal preferences.

Mode: You can select a sound mode to suit your personal preferences.

•

Balance: Controls the balance between the right and left speakers.

•

100Hz / 300Hz / 1KHz / 3KHz / 10KHz (Bandwidth Adjustment): To adjust the level of different bandwidth frequencies

•

Reset: Resets the equalizer settings to the default values.

•

/ On

❑

SRS TruSurround HD is the combined technology of TruSurround and FOCUS, TruBass. SRS TruSurround HD is down mixing technology that makes the Surround Sound effect of virtual 5.1 channel via two speakers.

This function provide not only rich deep bass at a low-pitched sound but also improve the resolution at a high-pitched sound.

If the sound is abnormal while TV is playing music, please adjust the equalizer and SRS TruSurround HD (Off/On).

TruSurround HD, SRS and the symbol are trademarks of SRS Labs, Inc. TruSurround HD technology is incorporated under license from SRS Labs, Inc.

Sound

Mode : Custom

Equalizer

SRS TruSurround HD : Off

Audio Language : ----

Audio Format : ----

Audio Description

Auto Volume : Off

 

Audio Language (only digital channel)

❑

You can change the default value for audio languages. Displays the language information for the incoming stream.

You can only select the language among the actual languages being broadcast.

 / Dolby Digital (only digital channel)

❑

When sound is emitted from both the main speaker and the audio receiver, a sound echo may occur due to the decoding speed

difference between the main speaker and the audio receiver. In this case, use the TV Speaker function.

You can only select the language among the actual languages being broadcast.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

Audio Description (only digital channel)

❑

This is an auxiliary audio function that provides an additional audio track for visually challenged persons. This function handles the

Audio Stream for the AD (Audio Description), when it is sent along with the Main audio from the broadcaster. Users can turn the

Audio Description On or Off and control the volume.

   Off / On



Turn the audio description function on or off.

Volume



You can adjust the audio description volume.

Volume is active when Audio Description is set to On.

English - 20

Continued...

+ 44 hidden pages