MODEL
MF 9325
MF 9331
DIGITAL MULTIFUNCTIONAL
SYSTEM
KEY OPERATOR'S GUIDE
• PURPOSE OF THE KEY
OPERATOR PROGRAMS
• PROGRAMMING A KEY
OPERATOR CODE
•
USING THE KEY
OPERATOR PROGRAMS
• KEY OPERATOR
PROGRAM LIST
• GENERAL PROGRAMS
• PROGRAMS FOR
COPY MODE
• PROGRAMS FOR
PRINT MODE
Page
1
1
2
4
8
15
16
•
PROGRAMS FOR NETWORK
SCANNER MODE
20
The key operator code is initially set to "00000" at the factory.
PURPOSE OF THE KEY OPERATOR
PROGRAMS
The key operator programs are used by the key operator (administrator of the machine) to customize certain
features of the machine to better meet the needs of users.
This guide explains key operator programs that are common to all functions of the multifunction system (copy
function, fax function, printer function, and network scanner function), as well as programs that are specific to the
copy function, printer function, and network scanner function. Programs that are specific to the fax function are
explained in the following manual:
• Fax function ............."SG-FEK2 Operation manual" (Chapter 8)
In order to access the key operator programs, the key operator code must be entered.
PROGRAMMING A KEY OPERATOR CODE
The key operator code is a 5-digit number that must be entered in order to access the key operator programs. The
key operator (administrator of the machine) should change the default key operator code that was set at the factory
to a new 5-digit number. Be sure to remember the new key operator code, as it must be entered each time the key
operator programs are subsequently used. (Only one key operator code can be programmed.)
To change the key operator code, see "USING THE KEY OPERATOR PROGRAMS" on the following page.
The key operator code is initially set to "00000" at the factory.
1
USING THE KEY OPERATOR PROGRAMS
KEY OPERATOR CODE
OK
Note
Press the [CUSTOM SETTINGS] key.
1
STATUS
Touch the [KEY OPERATOR
2
When using the key operator programs for the first time, change the factory default key operator code to a new
code. (Step 3 to step 5)
LINE
DATA
CUSTOM SETTINGS
PROGRAMS] key.
CUSTOM SETTINGS
TOTAL COUNT
TRAY SETTINGS
KEYBOARD
SELECT
Use the numeric keys to enter the
3
DISPLAY
CONTRAST
ADDRESS
CONTROL
KEY OPERATOR PROGRAMS
LIST PRINT
RECEIVE MODE
CLOCK
FAX DATA
FORWARD
five-digit key operater code.
Each time a digit is
entered, the dash (-) that
indicates the digit will
change to an asterisk ( ).
The factory default setting
for the key operator code
is 00000.
EXIT
Use the numeric keys to enter the new
5
5-digit key operator code.
Use a number for the key
operator code that has not
been programmed as an
00000
-----
account number for
auditing mode (a number
that has been
programmed as an
account number cannot
be used). The entered number will be the new key
operator code. Be sure to remember this number.
Touch the [OK] key. You will return to
6
the screen of step 4.
This completes the
procedure for changing
the key operator code. If
you wish to configure
another program, touch
the key of the desired
program in the screen of
step 4.
Press the [CLEAR ALL] key ( ) to
7
exit the program.
Touch a key to select the desired
4
category of key operator programs.
KEY OPERATOR PROGRAMS
ACCOUNT
CONTROL
COPY SETTINGS PRINT SETTINGS
LIST PRINT
ENERGY SAVE
KEY OPERATOR
CODE CHANGE
OPERATION
SETTINGS
SCANNER
SETTINGS
PRODUCT KEY
Example:
To change the key operator code, touch the [KEY
OPERATOR CODE CHANGE] key.
• Each time you need to configure a program, use this
procedure to select the program.
• In the following steps, the setting screen for the
selected program appears. Refer to the explanation
of the program to select the desired setting (the
explanations of the programs begin on page 8).
EXIT
DEVICE CONTROL
FAX SETTINGS
2
KEYS USED IN KEY OPERATOR PROGRAMS
Example: Auditing mode
KEY OPERATOR PROGRAMS
ACCOUNT CONTROL
USING THE KEY OPERATOR PROGRAMS
The following keys appear in screens that
require the entry of numerical values.
(1 999)
OK
20
1
2
AUDITING MODE
TOTAL PAGES PER ACCOUNT
RESETTING ACCOUNT
1/3
3
4 5
1
When a checkbox ( ) appears in front of a setting, a checkmark ( ) will appear when the checkbox is touched.
This indicates that the setting is enabled. If a checkbox with a checkmark ( ) is touched, the checkmark is
cleared ( ) and the setting is disabled.
2
When a key that appears in the form is touched, the setting screen of that key will appear.
3
If the settings continue on the following screen(s), touch the and keys to move back and forth through the
X X X
screens. To return to the category selection screen, touch the [OK] key.
4
The currently set numerical value is displayed.
5
Numerical values can be set by touching the and keys.
3
KEY OPERATOR PROGRAM LIST
Note
The key operator programs that can be accessed depend on the optional equipment that is installed.
GENERAL PROGRAMS
Program name
ACCOUNT CONTROL
AUDITING MODE Disabled 8
TOTAL PAGES PER
ACCOUNT
RESETTING ACCOUNT — 8
ACCOUNT NUMBER
CONTROL
ACCOUNT LIMIT SETTING
ACCOUNT NUMBER
SECURITY
CANCEL JOBS OF
INVALID ACCOUNTS
ENERGY SAVE
AUTO POWER SHUT-OFF Enabled 10
AUTO POWER SHUT-OFF
TIMER
PREHEAT MODE SETTING
TONER SAVE MODE
OPERATION SETTINGS
AUTO CLEAR SETTING 60 (sec) 11
MESSAGE TIME SETTING 6 (sec) 11
KEYS TOUCH SOUND • KEYS TOUCH
TOUCH KEY OPERATION
SETTING
DISABLE INTERRUPT
PRINT JOB
STREAM FEEDING MODE
DISPLAY LANGUAGE
SETTING
DISABLE DISPLAY
TIMEOUT
DISABLING OF TRAY
SETTINGS
DISABLING OF CLOCK
ADJUSTMENT
*4
Factory default
settings
—8
—9
—9
Disabled 9
Disabled 9
60 (min.) 10
15 (min.) 10
Disabled 10
SOUND: Short
• KEYS TOUCH
SOUND AT
INITIAL POINT:
Disabled
• Time to entry:
0.0 (sec)
• DISABLE AUTO
KEY REPEAT:
Disabled
Disabled 11
Disabled 12
ENGLISH 12
Disabled 12
Disabled 12
Disabled 12
Page
11
11
Program name
DEVICE CONTROL
DISABLING OF
DOCUMENT FEEDER
DISABLING OF DUPLEX Disabled 12
DISABLING OF STAPLER
OUTPUT TRAYS
OFFSET FUNCTION
SETTING
MEMORY FOR PRINTER
DISABLING OF CENTRE
TRAY COUNTING
RETURN FROM COPY
MODE TIMING
MIX SIZE ORIGINAL
FEEDING MODE
SECURITY SETTINGS — 13
KEY OPERATOR CODE CHANGE
PRODUCT KEY
PS3 EXPANSION KIT
NETWORK SCANNER
EXPANSION KIT
E-MAIL ALERT AND STATUS
SERIAL NUMBER — 14
*3
*4
*4
*5
Factory default
settings
Disabled 12
*2
Disabled 12
PAT T ER N 1 13
Enabled 13
• 50%
• MEMORY AREA
FOR PRINT
*4
HOLD
Disabled 13
60 (sec) 13
Disabled 13
00000 14
—14
—14
*4
—14
: 30%
PROGRAMS FOR COPY MODE
Program name
COPY SETTINGS
INITIAL STATUS SETTINGS — 15
ROTATION COPY SETTING Enabled 15
EXPOSURE ADJUSTMENT • Document
AUTO PAPER SELECTION
SETTING
SETTING A MAXIMUM
NUMBER OF COPIES
SORT AUTO SELECT Enabled 15
DISABLING DELETION OF
JOB PROGRAMS
CARD SHOT SETTINGS — 15
Factory default
settings
glass: 3
• Document
feeder: 3
PLAIN PAPER 15
999 15
Disabled 15
Page
13
Page
15
4
KEY OPERATOR PROGRAM LIST
PROGRAMS FOR PRINT MODE
Program name
PRINT SETTINGS
DEFAULT SETTINGS
PROHIBIT NOTICE PAGE
PRINTING
PRINT DENSITY LEVEL 3 16
PROHIBIT TEST PAGE
PRINTING
ROTATED PRINT Enabled 16
FORCED OUTPUT OF
PRINT
EXCLUDE BYPASS-TRAY
FROM ATS
DISABLE DEFAULT
SETTING CHANGES
INTERFACE SETTINGS
HEXADECIMAL DUMP
MODE
I/O TIMEOUT 180 (sec)
PARALLEL PORT
EMULATION SWITCHING
USB PORT EMULATION
SWITCHING
NETWORK PORT
EMULATION SWITCHING
PORT SWITCHING
METHOD
ENABLE PARALLEL
PORT
ENABLE USB PORT
ENABLE NETWORK
PORT
ENABLE ECP
NETWORK SETTINGS
IP ADDRESS SETTING
ENABLE TCP/IP Enabled 18
ENABLE NetWare Enabled 18
ENABLE EtherTalk Enabled 19
ENABLE NetBEUI Enabled 19
RESET THE NIC — 19
INITIALISE AND/OR STORE SETTINGS
RESTORE FACTORY
DEFAULTS
STORE CURRENT
CONFIGURATION
RESTORE
CONFIGURATION
*4
*4
*4
*4
*4
*4
*4
*4
Factory default
settings
Disabled 16
Disabled 16
Disabled 16
Enabled 16
*4
*4
Disabled 16
Disabled 17
60 (sec)
AUTO 17
*4
PCL 17
AUTO 17
*4
SWITCH AT
END OF JOB
Enabled 18
Enabled 18
Enabled 18
Disabled 18
DHCP: Enabled
—19
—19
—19
*4
*4
Page
17
18
18
PROGRAMS FOR NETWORK SCANNER MODE
Program name
SCANNER SETTINGS
INITIAL FILE FORMAT
SETTING
INITIAL QUALITY
SETTING
INITIAL RESOLUTION
SETTING
DEFAULT DISPLAY
SETTINGS
THE NUMBER OF DIRECT
ADDRESS / SENDER KEYS
DISPLAYED SETTING
*1 Appears when the scanner function is enabled.
*2 Appears when a FINISHER is installed.
*3 Can be enabled when the printer or fax function is
enabled and a JOB SEPARATOR TRAY KIT or
FINISHER is installed.
*4 Appears when the PRINTER EXPANSION KIT is
installed.
*5 Appears when the PRINTER EXPANSION KIT and
EXPANSION MEMORY are installed.
Factory default
settings
*1
• File type: TIFF
• Compression
mode: G4
• Number of pages
per file: All
• Original image
type: Text/Photo
• Exposure: Auto
300 dpi 20
CONDITION
SETTINGS
8 (keys) 20
Page
20
20
20
5
KEY OPERATOR PROGRAM LIST
KEY OPERATOR PROGRAM MENU
The key operator programs are arranged in the following menu.
Refer to this menu when enabling or disabling the settings that are explained beginning on page 8.
* Some programs contain an additional level of settings (setting screen).
Level 1 Level 2 Level 3
ACCOUNT CONTROL AUDITING MODE
TOTAL PAGES PER ACCOUNT
RESETTING ACCOUNT
ACCOUNT NUMBER CONTROL
ACCOUNT LIMIT SETTING
ACCOUNT NUMBER SECURITY
CANCEL JOBS OF INVALID ACCOUNTS
ENERGY SAVE AUTO POWER SHUT-OFF
AUTO POWER SHUT-OFF TIMER
PREHEAT MODE SETTING
TONER SAVE MODE
OPERATION SETTINGS AUTO CLEAR SETTING
MESSAGE TIME SETTING
KEYS TOUCH SOUND
TOUCH KEY OPERATION SETTING
DISABLE INTERRUPT PRINT JOB
STREAM FEEDING MODE
DISPLAY LANGUAGE SETTING
DISABLE DISPLAY TIMEOUT
DISABLING OF TRAY SETTINGS
DISABLING OF CLOCK ADJUSTMENT
DEVICE CONTROL
Enter Key Operator Code
KEY OPERATOR CODE CHANGE ENABLE IPsec
DISABLING OF DOCUMENT FEEDER
DISABLING OF DUPLEX
DISABLING OF STAPLER
OUTPUT TRAYS
OFFSET FUNCTION SETTING
MEMORY FOR PRINTER
DISABLING OF CENTRE TRAY COUNTING
RETURN FROM COPY MODE TIMING
MIX SIZE ORIGINAL FEEDING MODE
SECURITY SETTINGS SSL SETTINGS
6
PRODUCT KEY PS3 EXPANSION KIT
NETWORK SCANNER EXPANSION KIT
E-MAIL ALERT AND STATUS
SERIAL NUMBER
COPY SETTINGS INITIAL STATUS SETTINGS
ROTATION COPY SETTING
EXPOSURE ADJUSTMENT
AUTO PAPER SELECTION SETTING
SETTING A MAXIMUM NUMBER OF COPIES
SORT AUTO SELECT
DISABLING DELETION OF JOB PROGRAMS
CARD SHOT SETTINGS
KEY OPERATOR PROGRAM LIST
Level 1 Level 2 Level 3
PRINT SETTINGS DEFAULT SETTINGS
INTERFACE SETTINGS HEXADECIMAL DUMP MODE
Enter Key Operator Code
NETWORK SETTINGS IP ADDRESS SETTING
PROHIBIT NOTICE PAGE PRINTING
PRINT DENSITY LEVEL
PROHIBIT TEST PAGE PRINTING
ROTATED PRINT
FORCED OUTPUT OF PRINT
EXCLUDE BYPASS-TRAY FROM ATS
DISABLE DEFAULT SETTING
CHANGES
I/O TIMEOUT
PARALLEL PORT EMULATION
SWITCHING
USB PORT EMULATION
SWITCHING
NETWORK PORT EMULATION
SWITCHING
PORT SWITCHING METHOD
ENABLE PARALLEL PORT
ENABLE USB PORT
ENABLE NETWORK PORT
ENABLE ECP
ENABLE TCP/IP
ENABLE NetWare
ENABLE EtherTalk
ENABLE NetBEUI
RESET THE NIC
INITIALISE AND/OR STORE SETTINGS
SCANNER SETTINGS INITIAL FILE FORMAT SETTING
INITIAL QUALITY SETTING
INITIAL RESOLUTION SETTING
DEFAULT DISPLAY SETTINGS
THE NUMBER OF DIRECT ADDRESS /
SENDER KEYS DISPLAYED SETTING
RESTORE FACTORY DEFAULTS
STORE CURRENT
CONFIGURATION
RESTORE CONFIGURATION
7
GENERAL PROGRAMS
This chapter explains key operator programs that are common to all functions of the multifunction system (copy
function, fax function, printer function, and network scanner function).
ACCOUNT CONTROL
KEY OPERATOR PROGRAMS
ACCOUNT CONTROL
AUDITING MODE
TOTAL PAGES PER ACCOUNT
RESETTING ACCOUNT
"ACCOUNT CONTROL" consists of the following
programs.
● AUDITING MODE
● TOTAL PAGES PER ACCOUNT
● RESETTING ACCOUNT
● ACCOUNT NUMBER CONTROL
● ACCOUNT LIMIT SETTING
● ACCOUNT NUMBER SECURITY
● CANCEL JOBS OF INVALID ACCOUNTS *
* Appears when the PRINTER EXPANSION KIT is
installed.
AUDITING MODE
When AUDITING MODE is enabled, a count is kept of
the pages printed by each account (up to 100 accounts
can be established). The page counts can be viewed
in the display. This program is initially disabled (factory
default setting).
Note
When using the copy function, fax function, or network
scanner function, an account number must be entered
to scan an original.
After enabling "AUDITING MODE", program
account numbers using "ACCOUNT
NUMBER CONTROL".
OK
1/3
TOTAL PAGES PER ACCOUNT
This program is used to display the page counts of
each account. Misfed pages are not included in the
page counts. When the fax and network scanner
functions are used, the fax and network scanner page
counts show the number of pages transmitted.
Touch the [TOTAL PAGES PER ACCOUNT] key to
display the page count screen.
KEY OPERATOR PROGRAMS
TOTAL PAGES PER ACCOUNT
ACCOUNT
NUMBER
11111
22222
33333
44444
COPIES
(LIMIT)
123,456
(150,000)
123,456
(150,000)
123,456
(150,000)
123,456
(150,000)
PRINTS SCAN FAX SEND
123,456
123,456
123,456
123,456
123,456
123,456
123,456
123,456
123,456
123,456
123,456
123,456
1/2
OK
RESETTING ACCOUNT
This program is used to reset the page counts of each
account to zero.
When the fax and network scanner functions are used,
this program resets the fax and network scanner page
counts to zero.
Touch the [RESETTING ACCOUNT] key to display the
account reset screen.
KEY OPERATOR PROGRAMS
RESETTING ACCOUNT
ACCOUNT
NUMBER
11111
22222
33333
44444
COPIES
(LIMIT)
123,456
(150,000)
123,456
(150,000)
123,456
(150,000)
123,456
(150,000)
PRINTS SCAN FAX SEND
123,456
123,456
123,456
123,456
123,456
123,456
123,456
123,456
123,456
123,456
123,456
123,456
1/2
● Resetting a single account
Touch the key of the account that you wish to reset,
and then select [YES] in the confirmation screen. If
the account that you wish to reset does not appear,
touch the key or key until the account
appears. When finished, touch the [OK] key.
OK
ALL ACCOUNTS
RESET
8
● Resetting all accounts
Touch the [RESET] key and then select [YES].
When finished, touch the [OK] key.
GENERAL PROGRAMS
ACCOUNT NUMBER CONTROL
This program is used to store, delete, and change
account numbers for AUDITING MODE. A maximum
of 100 account numbers can be stored.
● Storing a new account number
To store a new account number, touch the [ENTER]
key and then use the numeric keys to enter a 5-digit
account number. Touch the [ENTER] key to store
the number. After storing the account number, you
can continue storing other account numbers.
Note that the same number as the key operator
code cannot be stored.
● Deleting an account number
To delete an account number, touch the [DELETE]
key and then select whether you wish to delete a
single account number or all account numbers.
To delete a single account number, use the numeric
keys to enter the account number that you wish to
delete and then touch the [ENTER] key.
To delete all account numbers, touch the [DELETE]
key and then touch [YES] in the screen that appears
to confirm the deletion.
● Changing an account number
To change an account number, touch the
[CHANGE] key and use the numeric keys to enter
the account number that you wish to change. Enter
the new account number and then touch the
[ENTER] key. After changing the account number,
you can continue changing other account numbers.
If you make a mistake while entering the account
number that you wish to change and enter a number
that is not in use, an alarm will sound and the display
will change to hyphens (-).
ACCOUNT LIMIT SETTING
A limit for the number of copies that can be made can
be set for a single account or for all accounts at once.
The maximum limit that can be entered is 999,999.
Touch the [ACCOUNT LIMIT SETTING] key to display
the account limit setting screen.
KEY OPERATOR PROGRAMS
ACCOUNT LIMIT SETTING
INPUT ACCOUNT NUMBER TO BE LIMITED.
ACCOUNT
NUMBER
-----
LIMIT ENTER
NUMBER OF
COPIES MADE
123,456
MAXIMUM
---,---
● Setting a limit for a single account
Use the numeric keys to enter the number of the
account for which you wish to set a limit, and then
enter the limit. When finished, touch the [ENTER]
key.
If you enter an account number that already has a
limit, the limit will appear in the display. To change
the limit, press the [CLEAR] key ( ) (the display
will change to hyphens (-)) and then enter the new
limit.
If you touch the [ENTER] key while the display
shows hyphens (-) for the limit, the limit set for the
account will be cancelled. When you have finished
setting a limit for one account, you can continue
setting limits for other accounts.
When finished, touch the [OK] key to exit.
● Setting a limit for all accounts
Touch the [LIMIT] key. [ALL] will appear in the
account number entry screen.
Enter a limit for all acounts in the same way as
explained above for a single account.
When finished, touch the [OK] key to exit.
OK
ACCOUNT NUMBER SECURITY
This program is used to display an alarm and prohibit
entry of account numbers for one minute if an incorrect
acount number is entered three times in a row when
"AUDITING MODE" is enabled. (This prevents
unauthorised people from attempting to guess an
account number.)
This program is initially disabled (factory default setting).
CANCEL JOBS OF INVALID ACCOUNTS
This program is used to control use of the printer
function when "AUDITING MODE" is enabled. When
this program is enabled, the machine will not print a
print job if the operator enters an invalid account
number at the computer or fails to enter an account
number.
When the program is disabled, print jobs received
without the entry of a valid account number will be
printed and the number of pages will be included in the
[OTHERS] count.
This program is initially disabled (factory default setting).
9
GENERAL PROGRAMS
ENERGY SAVE
KEY OPERATOR PROGRAMS
ENERGY SAVE
AUTO POWER SHUT-OFF
AUTO POWER SHUT-OFF TIMER
PREHEAT MODE SETTING
60min
15min
"ENERGY SAVE" provides the following four programs
to reduce your power costs. From an environmental
perspective, this also helps conserve natural
resources and reduce pollution.
● AUTO POWER SHUT-OFF
● AUTO POWER SHUT-OFF TIMER
● PREHEAT MODE SETTING
● TONER SAVE MODE
AUTO POWER SHUT-OFF
If the machine is not used for the amount of time set in
"AUTO POWER SHUT-OFF TIMER", AUTO POWER
SHUT-OFF will activate and switch the machine to a
standby state that conserves the maximum amount of
energy. This program can be used to prevent AUTO
POWER SHUT-OFF from operating. When this is
done, the "AUTO POWER SHUT-OFF TIMER" setting
is disabled. Use this program when circumstances
require that AUTO POWER SHUT-OFF be disabled.
This program is initially enabled (factory default
setting).
OK
PREHEAT MODE SETTING
If the printer is not used for the length of time set with
this program after printing is finished, it will enter
preheat mode. This function reduces your power
costs, and at the same time helps conserve natural
resources and reduce pollution.
Select the most suitable setting to match your pattern
of use of the printer.
The time can be set to as long as 240 minutes in
increments of one minute. (Preheat mode cannot be
disabled.)
The factory default setting is "15" (min.).
TONER SAVE MODE
The toner save mode will reduce toner consumption by
approximately 10% in the automatic, text, and
text/photo exposure modes. Copies will be lighter but
still adequate for general use. Selection of this mode
has no effect on the photo and super photo modes.
This program is initially disabled (factory default
setting).
Caution
shut-off feature, we suggest that you
first try lengthening the time set in
"AUTO POWER SHUT-OFF TIMER" In
most cases a suitable timer setting
will allow work to proceed with
minimal delay and still enable you to
enjoy the benefits of power
conservation.
AUTO POWER SHUT-OFF TIMER
This program is used to set the amount of time after
which "AUTO POWER SHUT-OFF" activates when the
machine is not used.
This function allows you to reduce power costs, and at
the same time helps conserve natural resources and
reduce pollution.
The time can be set to as long as 240 minutes in
increments of one minute.
The factory default setting is "60" (min.).
Rather than disabling the auto power
Note
• Select a suitable time according to your
pattern of use of the machine.
• If "AUTO POWER SHUT-OFF" is disabled,
the time setting is also disabled.
10
GENERAL PROGRAMS
OPERATION SETTINGS
KEY OPERATOR PROGRAMS
OPERATION SETTINGS
AUTO CLEAR SETTING
MESSAGE TIME SETTING
KEYS TOUCH SOUND
60sec
6sec
The "OPERATION SETTINGS" are related to basic
operation of the machine and consist of the following
programs:
● AUTO CLEAR SETTING
● MESSAGE TIME SETTING
● KEYS TOUCH SOUND
● TOUCH KEY OPERATION SETTING
● DISABLE INTERRUPT PRINT JOB
● STREAM FEEDING MODE
● DISPLAY LANGUAGE SETTING
● DISABLE DISPLAY TIMEOUT
● DISABLING OF TRAY SETTINGS
● DISABLING OF CLOCK ADJUSTMENT
AUTO CLEAR SETTING
If no action is taken for a certain length of time when
viewing information on finished jobs, jobs in progress,
or stored jobs, the auto clear function activates and
returns the display to the initial screen of copy mode or
the job status screen. AUTO CLEAR SETTING is used
to set the amount of time that must elapse for the auto
clear function to activate. The time can be set from 10
seconds to 240 seconds in increments of 10 seconds,
or the auto clear function can be disabled. (This setting
only operates in copy mode and network scanner
mode.)
The factory default setting is "60" (sec.).
MESSAGE TIME SETTING
This program is used to set the length of time that
messages appear in the display (this applies to
messages that appear for a certain length of time and
then automatically disappear.)
The time can be set to as long as 12 seconds in
increments of one second.
The factory default setting is "6" (sec.).
OK
1/3
KEYS TOUCH SOUND
This program is used to select whether or not a beep is
sounded when a key is touched, and if sounded, what
type of beep.
The program is also use to select whether or not a
special key touch beep is sounded at the initial point of
a setting.
The factory default settings are as follows:
• KEYS TOUCH SOUND: Short
• KEYS TOUCH SOUND AT INITIAL POINT: Disabled
KEY OPERATOR PROGRAMS
KEYS TOUCH SOUND
KEYS TOUCH SOUND
KEYS TOUCH SOUND AT INITIAL POINT
key .... Touch this key to select a
volume. A single
short
valid key, and a double
beep indicates a
short
OK
short
beep
beep indicates
an invalid key.
key .... Touch this key to select a long beep
volume. A single long beep indicates a valid
key, and a double long beep indicates an
invalid key.
key .... Touch this key to disable key touch beeps.
Select the [KEYS TOUCH SOUND AT INITIAL POINT]
checkbox to have three long beeps sound (when the
beep volume is set to
(when the beep volume is set to
long
) or three short beeps sound
short
) when the initial
point of a setting is reached while selecting basic settings.
The initial point settings are as follows:
Mode
Initial point (set from initial screen)
Copy mode Ratio: 100%
Exposure: 3
Fax mode Exposure: 3
Network scanner
Exposure setting: 3
mode
TOUCH KEY OPERATION SETTING
These programs are used to set the length of time that
must elapse until a setting is entered after a key is
touched, and to disable key repeat.
The setting entry time can be set from 0.0 seconds to
2.0 seconds in increments of 0.5 seconds.
When [DISABLE AUTO KEY REPEAT] is enabled, only
one touch is registered if key is touched continuously.
The factory default settings are as follows:
• Time to entry: 0.0 (sec.)
• DISABLE AUTO KEY REPEAT: Disabled
DISABLE INTERRUPT PRINT JOB
(When the printer function is enabled)
Enable this program if you wish to prevent pausing of
printing for interrupt copy jobs.
This program is initially disabled (factory default setting).
11
GENERAL PROGRAMS
STREAM FEEDING MODE
(When an RSPF is installed)
Use this program to enable stream feeding mode.
When this mode is enabled and originals are scanned
from the RSPF, an original can be added to the RSPF
within 5 seconds after the previous original is fed, and
be automatically scanned using the settings of the
previous original. This function can be used with the
copy function and the scanner function.
This program is initially disabled (factory default
setting).
DISPLAY LANGUAGE SETTING
This program is used to change the language used in
the display.
The factory default setting is "ENGLISH".
DISABLE DISPLAY TIMEOUT
When this program is disabled, the display will close
the screen that is currently open and return to the
initial screen if no keys are touched for 60 seconds.
When the program is enabled, the display will not
close the screen that is currently open.
This program is initially disabled (factory default
setting).
DEVICE CONTROL
KEY OPERATOR PROGRAMS
DEVICE CONTROL
DISABLING OF DOCUMENT
FEEDER
DISABLING OF DUPLEX
DISABLING OF STAPLER
Use these programs when a peripheral device on the
machine has failed or when you wish to temporarily
disable a device. The programs can also be used to
change the function setting of a device as required by
your conditions of use.
"DEVICE CONTROL" consists of the following
programs:
● DISABLING OF DOCUMENT FEEDER
● DISABLING OF DUPLEX
● DISABLING OF STAPLER
● OUTPUT TRAYS
● OFFSET FUNCTION SETTING
● MEMORY FOR PRINTER
● DISABLING OF CENTRE TRAY COUNTING
● RETURN FROM COPY MODE TIMING
● MIX SIZE ORIGINAL FEEDING MODE
● SECURITY SETTINGS
OK
1/3
DISABLING OF TRAY SETTINGS
This program can be enabled to prohibit changes to
the paper tray settings in the user settings.
Note that bypass tray settings will still be possible.
This program is initially disabled (factory default
setting).
DISABLING OF CLOCK ADJUSTMENT
This program can be enabled to prohibit adjustment of
the "CLOCK" setting in the custom settings.
This program is initially disabled (factory default
setting).
DISABLING OF DOCUMENT FEEDER
(When an RSPF is installed)
Use this program when the RSPF is not operational or
you wish to disable the automatic feeding function.
(Originals can still be scanned using the document
glass.)
This program is initially disabled (factory default
setting).
DISABLING OF DUPLEX
Use this program when you wish to disable the
two-sided printing function or the function has failed.
When this program is enabled, only one-sided printing
is possible.This program is initially disabled (factory
default setting).
DISABLING OF STAPLER
(When a FINISHER is installed)
Use this program to disable stapling.
When this program is enabled, stapling does not take
place.This program is initially disabled (factory default
setting).
12
GENERAL PROGRAMS
OUTPUT TRAYS
(When the printer or fax function is enabled and a JOB
SEPARATOR TRAY KIT or FINISHER is installed)
This program is used to select the respective output
trays for the copy, printer, and fax functions.
The factory default setting is "PATTERN 1".
Example: When a FINISHER is installed
* Settings that can be selected vary depending on the
options that are installed.
Settings Description
PATTERN 1 Copy: Offset tray
Printer: Centre tray
Fax: Top tray
PATTERN 2 Copy: Centre tray
Printer: Offset tray
Fax: Top tray
PATTERN 3
(When the fax
function is enabled)
PATTERN 4
(When the fax
function is enabled)
Copy: Centre tray
Printer: Offset tray
Fax: Centre tray
Copy: Offset tray
Printer: Centre tray
Fax: Centre tray
OFFSET FUNCTION SETTING
This program is used to enable or disable the offset
functions of the centre tray and offset tray (when a
FINISHER is installed).
This program is initially enabled (factory default
setting).
MEMORY FOR PRINTER
This program is used to set the amount of IMC
memory that is allocated to the printer function. The
amount of memory can be set from 30% to 70% in
increments of 10%.
The factory default settings are as follows:
•50 (%)
• THE MEMORY AREA FOR PRINT HOLD: 30 (%)
● Memory allocated to print hold
(When the PRINTER EXPANSION KIT is installed)
To set the amount of memory allocated to print hold,
touch the [THE MEMORY AREA FOR PRINT
HOLD] key. The amount of memory can be set from
30% to 70% in increments of 10%. If 0% is selected,
the print hold function cannot be used.
DISABLING OF CENTRE TRAY
COUNTING
This program is used to disable counting of pages
delivered to the centre tray.
When this program is enabled, centre tray full
detection does not take place.
This program is initially disabled (factory default
setting).
RETURN FROM COPY MODE TIMING
(When the printer function or fax function is enabled)
This program is used to set the amount of time that
must elapse after a copy job is finished before the
printer or fax function resumes operation. The amount
of time can be set from 1 second to 60 seconds in
increments of 1 second.
The factory default setting is "60" (sec.).
MIX SIZE ORIGINAL FEEDING MODE
(When an RSPF is installed)
When this program is enabled, originals of mixed
length (the widths must be the same) can be scanned
in copy mode and each original copied onto the
corresponding length of paper.
This program is initially disabled (factory default
setting).
SECURITY SETTINGS
The following settings are related to security. Touch
the [SECURITY SETTINGS] key to configure the
settings.
When any of these settings are changed, you must exit
the administrator settings, turn off the main switch,
wait a brief interval, and then turn the main switch back
on to make the new settings take effect.
● SSL SETTINGS
SSL can be used for data transmission over a
network.
SSL is a protocol that enables the encryption of
information communicated over a network.
Encrypting data makes it possible to transmit and
receive sensitive information safely.
•
HTTPS: Apply SSL encryption to HTTP
communication.
•
IPP-SSL: Apply SSL encryption to IPP communication.
● ENABLE IPsec
IPsec can be used for data transmission/reception
on a network. When IPsec is used, data can be sent
and received safely without the need to configure
settings for IP packet encryption in a Web browser
or other higher-level application. This setting is only
used to enable or disable IPsec; detailed IPsec
settings are configured in the Web pages. Some
Web page settings may not allow connection to the
machine, or the settings may not allow printing,
scanning, or Web page display. In this case,
deselect [ENABLE IPsec] in this screen and change
the Web page settings.
KEY OPERATOR PROGRAMS
SECURITY SETTINGS
SSL SETTINGS
ENABLE IPsec
OK
13
GENERAL PROGRAMS
KEY OPERATOR CODE
CHANGE
This program is used to change the key operator code
that must be entered to configure the key operator
programs. When the machine is first used, the key
operator (adminstrator of the machine) should change
the key operator code that was set at the factory to the
desired 5-digit code. (A number that has been
programmed as an account number cannot be used.)
Only one key operator code can be programmed.
The factory default setting for the key operator code is
00000.
PRODUCT KEY
(When the PRINTER
EXPANSION KIT is installed)
KEY OPERATOR PROGRAMS
PRODUCT KEY
PS3 EXPANSION KIT
E-MAIL ALERT AND STATUS
Use these programs to enter the product keys for the
following options.
NETWORK SCANNER EXPANSION KIT
SERIAL NUMBER
PS3 EXPANSION KIT
(When the PRINTER EXPANSION KIT is
installed)
This program is used to enter the product key that
enables the machine to be used as a PostScript
printer. Ask your dealer for the product key.
NETWORK SCANNER EXPANSION KIT
(When the
EXPANSION MEMORY are installed)
This program is used to enter the product key for the
network scanner function. Ask your dealer for the
product key.
PRINTER EXPANSION KIT
OK
and
E-MAIL ALERT AND STATUS
(When the PRINTER EXPANSION KIT is
installed)
This program is used to enter the product key for
E-MAIL ALERT AND STATUS, which enables
customer product support via a network system. Ask
your dealer for the product key.
SERIAL NUMBER
Use this program to display the serial number of the
machine. The serial number is required when
obtaining product keys for PS3 EXPANSION KIT,
NETWORK SCANNER EXPANSION KIT and the
E-MAIL ALERT AND STATUS.
14
PROGRAMS FOR COPY MODE
This chapter explains the key operator programs that are used for copy mode.
COPY SETTINGS
KEY OPERATOR PROGRAMS
COPY FUNCTION SETTINGS
INITIAL STATUS SETTINGS
ROTATION COPY SETTING
EXPOSURE ADJUSTMENT
"COPY SETTINGS" consists of the following
programs:
● INITIAL STATUS SETTINGS
● ROTATION COPY SETTING
● EXPOSURE ADJUSTMENT
● AUTO PAPER SELECTION SETTING
● SETTING A MAXIMUM NUMBER OF COPIES
● SORT AUTO SELECT
● DISABLING DELETION OF JOB PROGRAMS
● CARD SHOT SETTINGS
AE:3
AE:3
INITIAL STATUS SETTINGS
The copy settings revert to the default settings when
the power switch is turned on, when the [CLEAR ALL]
key ( ) is pressed, or when the auto clear time
elapses. This program is used to change the default
settings, or return changed default settings to the initial
factory default settings.
Defaults for the following copy settings can be
changed:
• Paper tray • Exposure mode
• Copy ratio • Duplex function
• Post-processing functions* (non-sort, sort, staple
sort, and group)
*Settings for the post-processing functions vary
depending on whether or not a FINISHER is
installed.
Note
If this program is used to change the default
setting for the duplex function to other than
"one-sided" "one-sided" and the RSPF
fails or is disabled, the setting will revert to
"one-sided" "one-sided".
* DISABLING OF DOCUMENT FEEDER (p.12)
DISABLING OF DUPLEX (p.12)
OK
1/3
EXPOSURE ADJUSTMENT
This program is used to adjust the exposure level
when "Auto" is used for the copy exposure.
The auto exposure level can be set separately for the
document glass and RSPF.
[1] is the lightest level and [5] is the darkest level.
The factory default settings are as follows:
• Document glass: 3
• Document feeder: 3
AUTO PAPER SELECTION SETTING
This program is used to select the paper type* that is
used when the automatic paper selection function
operates. "PLAIN PAPER" or "PLAIN AND RECYCLE
PAPER" can be selected. Auto paper selection can
also be disabled with this program.
The factory default setting is "PLAIN PAPER".
* The paper type set for each tray in the tray settings of
the user settings. (See "CUSTOM SETTINGS" in the
operation manual for copier.)
SETTING A MAXIMUM NUMBER OF
COPIES
This program is used to set the maximum number of
copies that are allowed per original.
Any number from 1 to 999 can be set for the
maximum.
The factory default setting is "999".
SORT AUTO SELECT
(When an RSPF is installed)
This program can be used to disable automatic
selection of the sort function.
This program is initially enabled (factory default
setting).
DISABLING DELETION OF JOB
PROGRAMS
This program is used to prevent copy settings stored in
job programs from being changed or deleted.
This program is initially disabled (factory default
setting).
ROTATION COPY SETTING
When this program is enabled, the original image is
automatically rotated 90 degrees in the event that the
original and the paper are in different orientations.
(Rotation can only take place when auto paper
selection and automatic ratio selection are used.)
This program is initially enabled (factory default
setting).
CARD SHOT SETTINGS
This program is used to set the initial original card size
for the card shot function. Entry of the X dimension
(width) is initially selected. Touch the keys to enter the
Y dimension (length) in the same way. To have "FIT
TO PAGE" be initially selected when the card shot
screen is opened, touch the [FIT TO PAGE] key.
15
PROGRAMS FOR PRINT MODE
This chapter explains key operator programs that are used for the printer function. These programs can only be
configured on models that have the printer function.
PRINT SETTINGS
KEY OPERATOR PROGRAMS
PRINT SETTINGS
DEFAULT SETTINGS
NETWORK SETTINGS
INTERFACE SETTINGS
INITIALISE AND/OR STORE
SETTINGS
DEFAULT SETTINGS
These programs allow you to change certain default
settings for the printer function.
The "DEFAULT SETTINGS" consist of the following
programs:
● PROHIBIT NOTICE PAGE PRINTING
● PRINT DENSITY LEVEL
● PROHIBIT TEST PAGE PRINTING
● ROTATED PRINT
● FORCED OUTPUT OF PRINT
● EXCLUDE BYPASS-TRAY FROM ATS
● DISABLE DEFAULT SETTING CHANGES
OK
FORCED OUTPUT OF PRINT
This program is used to enable or disable automatic
printing on a different size of paper when no paper
trays have the selected size of paper.
This program is initially disabled (factory default
setting).
EXCLUDE BYPASS-TRAY FROM ATS
This program is used to exclude paper in the bypass
tray when automatic paper selection is used.
This program is initially enabled (factory default
setting).
DISABLE DEFAULT SETTING
CHANGES
(When the PRINTER EXPANSION KIT is installed)
This program is used to prevent the configuration
setting defaults from being changed.
This program is initially disabled (factory default
setting).
PROHIBIT NOTICE PAGE PRINTING
This program is used to prohibit the printing of notice
pages. For an explanation of notice pages, see "If a
Notice Page is printed" in the online manual for printer.
This program is initially disabled (factory default
setting).
PRINT DENSITY LEVEL
The print density can be set to one of five different
levels. [1] is the lightest level and [5] is the darkest
level.
The factory default setting is "3".
PROHIBIT TEST PAGE PRINTING
(When the PRINTER EXPANSION KIT is installed)
This program is used to prohibit the printing of test
pages.
When the program is enabled, a test page cannot be
printed from the user settings. (See the operation
manual for copier)
This program is initially disabled (factory default
setting).
ROTATED PRINT
This program is used to enable or disable rotation of
the print image when an A4R, B5R, or 8-1/2 x 11R
(Letter R) document is being printed but there is no
paper loaded in that orientation.
This program is initially enabled (factory default
setting).
16
PROGRAMS FOR PRINT MODE
INTERFACE SETTINGS
The "INTERFACE SETTINGS" are used to monitor
and set limits for the data that is sent to the machine’s
parallel port, USB port, or network port. The settings
consist of the following programs:
● HEXADECIMAL DUMP MODE
● I/O TIMEOUT
● PARALLEL PORT EMULATION SWITCHING
● USB PORT EMULATION SWITCHING
● NETWORK PORT EMULATION SWITCHING
● PORT SWITCHING METHOD
● ENABLE PARALLEL PORT
● ENABLE USB PORT
● ENABLE NETWORK PORT
● ENABLE ECP
HEXADECIMAL DUMP MODE
(When the PRINTER EXPANSION KIT is installed)
This program is used to print out the print data from the
computer in hexadecimal and in the corresponding text
characters (based on ASCII code). This allows you to
check whether or not print data is being correctly sent
from the computer.
This program is initially disabled (factory default
setting).
Example of output in hexadecimal dump mode (A4
portrait)
PARALLEL PORT EMULATION
SWITCHING
(When the PRINTER EXPANSION KIT is installed)
This program is used to set the printer language when
the machine is connected using the parallel port.
The factory default setting is "AUTO".
Unless printing errors occur frequently, it is
recommended that the setting be kept at "AUTO".
Selections Description
AUTO The printer language is
automatically changed to match
the data received from the
computer.
PostScript
(When the PS3
EXPANSION
KIT is installed)
PCL The data received from the
The data received from the
computer is printed using
PostScript.
computer is printed using PCL.
USB PORT EMULATION SWITCHING
(When the PRINTER EXPANSION KIT is installed)
This program is used to set the printer language when
the machine is connected using the USB port. The
selections are the same as for "PARALLEL PORT
EMULATION SWITCHING".
The factory default setting is "PCL*".
* When the PS3 expansion kit is installed, the setting is
"AUTO".
Unless printing errors occur frequently, it is
recommended that the setting be kept at "AUTO".
I/O TIMEOUT
This program is used to set the amount of time until I/O
timeout when waiting for print data.
In the event that the set amount of time elapses
without the port receiving any print data, the I/O
timeout function temporarily breaks the port
connection and intiates automatic port selection or
makes the port begin waiting for the next set of print
data.
The factory default settings are as follows:
• 180 (sec.)
• When the PRINTER EXPANSION KIT is installed:
60 (sec.)
NETWORK PORT EMULATION
SWITCHING
(When the PRINTER EXPANSION KIT is installed)
This program is used to set the printer language when
the machine is connected using the USB port. The
selections are the same as for "PARALLEL PORT
EMULATION SWITCHING".
The factory default setting is "AUTO".
Unless printing errors occur frequently, it is
recommended that the setting be kept at "AUTO".
17
PROGRAMS FOR PRINT MODE
PORT SWITCHING METHOD
(When the PRINTER EXPANSION KIT is installed)
This program is used to set the method for switching
printer ports.
The machine can use the following three printer ports:
• Parallel port
•USB port
• Network port
The factory default setting is "SWITCH AT END OF
JOB".
Selections Description
SWITCH AT
END OF JOB
SWITCH AFTER
I/O TIMEOUT
Automatic printer port selection
at the end of each print job.
Automatic printer port selection if
the time set in "I/O TIMEOUT"
elapses.
ENABLE PARALLEL PORT
(When the PRINTER EXPANSION KIT is installed)
This program is used to enable or disable printing via
the parallel port.
This program is initially enabled (factory default
setting).
NETWORK SETTINGS
(When the PRINTER EXPANSION KIT is installed)
The NETWORK SETTINGS are used when the
machine is used as a network printer. The "NETWORK
SETTINGS" consist of the following programs:
● IP ADDRESS SETTING
● ENABLE TCP/IP
● ENABLE NetWare
● ENABLE EtherTalk
● ENABLE NetBEUI
● RESET THE NIC
Caution
Note
Consult your network administrator
before configuring the NETWORK
SETTINGS.
• After changing the settings, you must turn
off the machine’s power switch, wait
briefly, and then turn the switch back on in
order to make the changes take effect.
• Some programs in the following are
marked by "*1". This indicates that a
message will appear at the end of the
setting procedure asking you to confirm
execution of the new setting. If needed,
you can cancel the new setting by
touching the [NO] key.
ENABLE USB PORT
(When the PRINTER EXPANSION KIT is installed)
This program is used to enable or disable printing via
the USB port.
This program is initially enabled (factory default
setting).
ENABLE NETWORK PORT
(When the PRINTER EXPANSION KIT is installed)
This program is used to enable or disable printing via
the network port.
This program is initially enabled (factory default
setting).
ENABLE ECP
(When the PRINTER EXPANSION KIT is installed)
Enable this program when you wish to use ECP mode
on the parallel port.
This program is initially disabled (factory default
setting).
IP ADDRESS SETTING
This program is used to set the IP address (IP
address, Subnet Mask, and Gateway) of the machine
when TCP/IP protocol is used on the network.
When "DHCP" is selected, the machine will obtain an IP
address automatically. This is the factory default setting.
When the machine is used on a TCP/IP network, be
sure to enable the "ENABLE TCP/IP" program.
Caution
Note
When DHCP is used, the IP address
assigned to the machine may
automatically be changed on
occasion. If this happens, printing
will not be possible.
This setting is only effective in a network
environment that uses Ipv4 TCP/IP protocol.
To set an IP address on a Ipv6 TCP/IP
network, use the Web pages. In an IPv6
environment, the machine can use LPD or
IPP protocol.
ENABLE TCP/IP
This program must be enabled to use the machine on
a TCP/IP network. "IP ADDRESS SETTING" must
also be configured.
This program is initially enabled (factory default setting).
18
ENABLE NetWare
This program must be enabled to use the machine on
a network that uses NetWare protocol.
This program is initially enabled (factory default setting).
PROGRAMS FOR PRINT MODE
ENABLE EtherTalk
This program must be enabled to use the machine on
a network that uses EtherTalk protocol.
This program is initially enabled (factory default setting).
ENABLE NetBEUI
This program must be enabled to use the machine on
a network that uses NetBEUI protocol.
This program is initially enabled (factory default
setting).
RESET THE NIC
This program is used to restore all network settings to
the factory default settings.
*1
INITIALISE AND/OR STORE SETTINGS
(When the PRINTER EXPANSION KIT is installed)
These programs are used to return the configuration
settings (See the online manual for network printer)
and the "PRINT SETTINGS" (p.16) to the factory
default settings. The programs are also used to store
the current settings and to restore stored settings.
"INITIALISE AND/OR STORE SETTINGS" consists of
the following programs:
● RESTORE FACTORY DEFAULTS
● STORE CURRENT CONFIGURATION
● RESTORE CONFIGURATION
Note
RESTORE FACTORY DEFAULTS
This program is used to return the configuration
settings (see the online manual for network printer)
and the "PRINT SETTINGS" (p.16) to the factory
default settings. If you need a record of the current
settings before restoring the factory defaults, use
"Data list print" in the user settings to print a list of the
current settings. (See "CUSTOM SETTINGS" in the
operation manual for copier.)
Some programs in the following are marked
by "*1". This indicates that a message will
appear at the end of the setting procedure
asking you to confirm execution of the new
setting. If needed, you can cancel the new
setting by touching the [NO] key.
*1
STORE CURRENT CONFIGURATION
This program is used to store the current configuration
settings (see online manual for network printer) and
"PRINT SETTINGS" (p.16). The stored settings will not
be erased even if the power is turned off. To restore
the stored settings, use the "RESTORE
CONFIGURATION" program.
RESTORE CONFIGURATION
This program is used to restore settings that were
stored using the "STORE CURRENT
CONFIGURATION" program.
The current settings will change to the restored
settings.
Note
If any of the "NETWORK SETTINGS" (p.18)
were changed before execution of this
program, you must turn off the machine’s
power switch, wait briefly, and then turn the
switch back on in order to make the settings
take effect.
*1
*1
19
PROGRAMS FOR NETWORK
SCANNER MODE
This chapter explains key operator programs that are used for the network scanner function. These programs can
only be configured on models that have the network scanner function.
SCANNER SETTINGS
KEY OPERATOR PROGRAMS
SCANNER SETTINGS
INITIAL FILE FORMAT SETTING
INITIAL QUALITY SETTING
INITIAL RESOLUTION SETTING
The "SCANNER SETTINGS" consist of the following
programs:
● INITIAL FILE FORMAT SETTING
● INITIAL QUALITY SETTING
● INITIAL RESOLUTION SETTING
● DEFAULT DISPLAY SETTINGS
● THE NUMBER OF DIRECT ADDRESS / SENDER
KEYS DISPLAYED SETTING
INITIAL FILE FORMAT SETTING
Use this program to change the default file format (file
type, compression mode, and number of pages per
file) that is used when sending an image by Scan to
E-mail, Scan to Desktop, or Scan to FTP.
The factory default settings are as follows:
• File type: TIFF
• Compression mode: G4
• Number of pages per file: All
OK
1/2
THE NUMBER OF DIRECT ADDRESS /
SENDER KEYS DISPLAYED SETTING
This program is used to select the number of
one-touch keys that are displayed in the address book
screen and sender selection screen. Selections are
[6], [8], and [12].
The factory default setting is "8" (keys).
Note
Each displayed one-touch key name can be
up to 18 characters long when the number
of displayed one-touch keys is 6 or 8. Each
name can only be 10 characters long when
the number of displayed one-touch keys is
12.
INITIAL QUALITY SETTING
This program is used to set the default original type
and exposure level for network scanner mode.
For informatin on these settings, see the operation
manual for network scanner.
The factory default settings are as follows:
• Original image type: Text/Photo
• Exposure: Auto
INITIAL RESOLUTION SETTING
This program is used to set the default resolution for
network scanner mode.
The factory default setting is "300" (dpi).
DEFAULT DISPLAY SETTINGS
Use this program to select the initial screen that
appears when the [SCAN] key is pressed to switch to
network scanner mode, or when the [CLEAR ALL] key
( ) is pressed in scanner mode.
Three selections are available for the initial screen:
• CONDITION SETTINGS
• ADDRESS BOOK (ABC)
• ADDRESS BOOK (GROUP)
The factory default setting is "CONDITION SETTINGS".
20
MF 9325/MF 9331 KEY OPERATOR'S GUIDE
Loading...