00894645TACT SWITCHSKECAF WITHOUT LEDSW21,SW23,SW22 on PANEL-A BOARD3
JACK, EXT TERMINAL
02781101
02781189USB CONNECTORYKF45-0021JK1 on MAIN BOARD1
02900867CARD EJECTORSCAB1A56001
02900834CARD CONECTRSCAA1A2300CN1 on PC CARD BOARD1
13429274MIDI SOCKETYKF51-5041JK1 on JACK BOARD1
03231812RCA(PIN)YKC21-4173JK12 on JACK BOARD1
134492586.5MM JACKHLJ4306-01-3080JK7 on JACK BOARD1
134492756.5MM JACKYKB21-5074JK2,JK3 on JACK BOARD2
134492836.5MM JACKHLJ7101-01-3010JK8,JK11,JK9,JK10 on JACK BOARD4
134492846.5MM JACKHLJ7001-01-3010JK6,JK4 on JACK BOARD2
W16,SW1,SW14,SW4,SW12,SW11,SW10,S
W8,SW7,SW6,SW5,SW15 on PANEL-A
BOARD,
SW201,SW202,SW203,SW204,SW210,SW20
5,SW206,SW207,SW208,SW209 on PANELB BOARD
,SW516,SW503,SW518,SW514,SW513,SW51
2,SW520,SW515,SW521,SW522,SW523,SW5
19,SW506,SW511,SW501,SW517,SW505,SW
507,SW508,SW509,SW510,SW502,SW504 on
PANEL-C BOARD
USB CONNECTORYKF45-00201
10
+19
+23
14
Fantom-X8
DISPLAY UNIT
POWER SUPPLY UNIT
BENDER UNIT
KEYBOARD ASSY
PCB ASSY
03560889KCG057QV1DB-G00LCD1
NOTE: Replacement KCG057QV1DB-G00 should be made on a unit base.
01785823A1DU2L3B034SWITCHING REGULATOR1
NOTE: Replacement A1DU2L3B034 should be made on a unit base.
03234723PB-H0204BENDER1
NOTE: Replacement PB-H0204 should be made on a unit base.
72349667PA-588-FKEYBOARD-AFT ASSY1
NOTE: See ‘KEYBOARD PARTS LIST’ for details.
72564734MAIN BOARD ASSY1
NOTE: ‘MAIN BOARD ASSY’ includes the following parts.
03670045SHEETK4E(10)-55X15T15S1
03670034SHEETK4E(10)-23X20T15S1
NOTE: When you replace the MAIN BOARD ASSY for repairng, be sure to perform the
"MAIN BOARD SETTING FOR SELECTING MODEL PROCEDURE"(to see P24).
In addition, we supply the MAIN BOARD ASSY of FANTOM-X6 setting for spare parts.
72235090EXP BASE BOARD ASSY1
NOTE: ‘EXP BASE BOARD ASSY’ includes the following parts.
02019034PWB SPACERRSPLS-12L4
01902756PWB SPACERRSPS-12L4
72564278PANEL-B KEYTOP ASSY1
NOTE: ‘PANEL-B KEYTOP ASSY’ includes the following parts.
03120889D S-KEYTOPSX2H-B GRS4
03120890D S-KEYTOPSX1H-B GRS2
NOTE: ‘JACK BOARD ASSY’ includes the following parts.
# 03670001SHEETK4E(10)-77X55T15S1
40342856COATING CLIPCP-1S3
#72565490INVERTER BOARD ASSY1
15
Mar.2004
IC
02903723HD6417706IC (32BIT CPU)IC1 on MAIN BOARD1
02900978M66291GPIC (USB CONTROLLER)IC56 on MAIN BOARD1
03456167S1D13705F00A200IC (LCD-DRIVER CPU PERIPH)IC128 on MAIN BOARD1
03566067T6TV2TBG-00067IC (CUSTOM)IC102 on MAIN BOARD1
03562223UPD23C128040BLGY-819-MJHIC (MASK ROM)IC104 on MAIN BOARD1
03124989UPD23C128040ALGY-535-MJHIC (MASK ROM)IC33 on MAIN BOARD1
03124978UPD23C128040ALGY-536-MJHIC (MASK ROM)IC28 on MAIN BOARD1
03562234UPD23C128040BLGY-818-MJHIC (MASK ROM)IC103 on MAIN BOARD1
03560589TC58DVM92A1TG00BBHIC (FLASH MEMORY)IC53 on MAIN BOARD1
********MBM29LV160BE70TN-E1IC (FLASH MEMORY) IC19 on MAIN BOARD1
03342201K4S281632E-TC75IC (SDRAM)IC20,IC2,IC24,IC6 on MAIN BOARD4
03237689M12L64164A-7TIC (MEMORY DRAM)IC106 on MAIN BOARD1
03017590UDA1351TSIC (DIR DAC)IC75 on MAIN BOARD1
03231701AK4527BVQIC (AD/DA)IC60 on MAIN BOARD1
01458401TC74LVX4245FS(EL)IC (TTL)IC114,IC112 on MAIN BOARD2
01901623TC74LVXC3245FSIC (CMOS)2
03231678TC7WZ74FU(TE12L)IC (CMOS)1
03459745HD74LVC540ATELL-EIC (CMOS)IC111 on MAIN BOARD1
03346267HD74LV273ATELL-EIC (CMOS)IC90 on MAIN BOARD1
01349590TC7WU04FU(TE12L)IC (CMOS)IC16,IC26 on MAIN BOARD2
01677689HD74HC238FPELIC (CMOS)IC96 on MAIN BOARD1
03015390TC74HCT273AF(EL)IC (CMOS)IC54 on MAIN BOARD1
01455312TC7WH74FUIC (CMOS)IC115 on MAIN BOARD1
01675034TC74VHC138FT(EL)IC CMOSIC99,IC98 on MAIN BOARD2
01675023TC74VHC139FT(EL)IC (CMOS)IC107,IC108,IC110 on MAIN BOARD3
01783523TC74VHCT245AFT(EL)IC (CMOS)IC119,IC118,IC117 on MAIN BOARD3
01890367TC74VHC175FT(EL)IC (CMOS)IC52 on MAIN BOARD1
01348956TC7SH00FU(TE85L)IC (CMOS)IC105 on MAIN BOARD1
02451923HD74LV74ATELLIC (CMOS)1
01348945TC7SH32FU(TE85L)IC (CMOS)IC130 on MAIN BOARD1
02456756TC74VHCT04AFT(EL)IC (CMOS)IC9 on MAIN BOARD1
02675667HD74LV21ATELLIC (CMOS)IC91 on MAIN BOARD1
02451690HD74LV08ATELLIC (CMOS)IC94 on MAIN BOARD1
02129334TC7WH08FU(TE12L)IC (CMOS)IC120 on MAIN BOARD1
02675656HD74LV11ATELLIC (CMOS)IC92 on MAIN BOARD1
02675689HD74LV245ATELLIC (CMOS)IC1,IC2,IC3 on EXP BASE BOARD,
IC3,IC44,IC40,IC8,IC7,IC5 on MAIN
BOARD
03015234HD74LV32ATELLIC (CMOS)IC113,IC14,IC50 on MAIN BOARD3
02675645HD74LV04ATELLIC (CMOS)IC17,IC10 on MAIN BOARD2
02451912HD74LV00ATELLIC (CMOS)IC74,IC116 on MAIN BOARD2
01348901TC7SH04FU(TE85L)IC (CMOS)1
15189261M5218AFP-600EIC (BIPOLAR OP AMP)IC71,IC70,IC68,IC61,IC59 on MAIN
BOARD,
IC18,IC16,IC19,IC25,IC24 on JACK BOARD
00344390TA7805F(TE16L)IC (REGULATOR)IC58 on MAIN BOARD1
02671545PQ070XZ01ZPIC (REGULATOR)IC101,IC57 on MAIN BOARD2
03125089PQ1CY1032ZPIC (SWITCHING REGULATOR)IC100 on MAIN BOARD1
02900690P2027A-08TRICIC89 on MAIN BOARD1
01785178TC9271FSIC (DIGITAL OUT IF)IC62 on MAIN BOARD1
15199937M51953BFP-600CIC (RESET)IC18 on MAIN BOARD1
15189186UPC4570CIC (BIPOLAR OP AMP)IC4,IC2,IC3 on PANEL-A BOARD3
01785012HA17324IC (BIPOLAR OP AMP)IC1 on PANEL-A BOARD1
01783589HD74HC4052FPELIC (CMOS)IC14 on JACK BOARD ,IC503,IC501 on
PANEL-C BOARD
02894301HA17324ARPEL(FP-14DN)IC (CMOS OP)IC502 on PANEL-C BOARD1
03127267HD6433061G45FPIC (16BIT CPU)IC2 on JACK BOARD1
00129278SSC1080F0BICIC5 on JACK BOARD1
15269219H0HD74LS05FPELIC (TTL)IC12 on JACK BOARD1
01121834TC7W74FU TE12LICIC6 on JACK BOARD1
01783656HD74HC4053FPELIC CMOSIC23 on JACK BOARD1
15249104TC7S04F(TE85L)IC (CMOS)IC22 on JACK BOARD1
00567534TC74VHC138F(EL)IC (CMOS)IC9,IC8 on JACK BOARD2
01908678TC74VHCU04FT(EL)IC (CMOS)IC17 on JACK BOARD1
02451712HD74LV14ATELLIC (CMOS)IC1 on JACK BOARD1
15289105UPC4570G2-E2IC (BIPOLAR OP AMP)IC20 on JACK BOARD1
15289151NJM2904M-TE3IC (OP AMP)IC21,IC15,IC10,IC7 on JACK BOARD4
02900545PC410LKNIPIC (PHOTO COUPLER)IC11 on JACK BOARD1
6
+3
5
+5
2
+1
TRANSISTOR
16
02900778PW MOSFET XP132A1275SRTRANSISTORQ17 on MAIN BOARD1
153091012SA1037AKT146RTRANSISTORQ11,Q12 on MAIN BOARD,
Q28 on JACK BOARD
15329103T02SK880-GR(TE85R)FETQ7,Q8,Q10,Q9 on MAIN BOARD,
Q31 on JACK BOARD
00239812DTC114EUT106TRANSISTORQ14,Q15,Q16,Q18,Q13 on MAIN BOARD,
Q16,Q17,Q10,Q11,Q12,Q14,Q15,Q13 on
JACK BOARD
031261452SA933ASTPRTRANSISTORQ2 on PANEL-A BOARD1
151296262SD1468S TP QTRANSISTORQ3 on PANEL-A BOARD1
2
+1
4
+1
5
+8
Fantom-X8
TRANSISTOR
DIODE
153191012SC2412KR T146TRANSISTORQ42 on JACK BOARD,
009015232SA1681 (SC-62)(POW SW)TRANSISTORQ34 on JACK BOARD1
011212892SC4081 T106 QRSTRANSISTORQ24,Q23,Q18,Q19 on JACK BOARD4
026710232SC3052-T12-1ETRANSISTORQ35,Q41 on JACK BOARD2
153191052SC3326-ATRANSISTORQ30,Q25,Q27,Q32,Q33,Q37,Q38,Q39,Q40,Q
00239801DTA114EU T-106TRANSISTORQ20 on JACK BOARD1
02451378RN2427TRANSISTORQ3,Q8,Q7,Q4,Q5,Q9,Q6 on JACK BOARD7
15329533RN2307(TE85R)TRANSISTORQ21 on JACK BOARD1
02671267RT1N141C-T12-1TRANSISTORQ29,Q36 on JACK BOARD2
15329511DTC114TKT146DIGITAL TRANSISTORQ43 on JACK BOARD1
15329531RN1308-TE85RTRANSISTORQ22 on JACK BOARD1
01780045RB051L-40SCHOTTKY DIODED4 on MAIN BOARD1
15339130MA142WK-(TX)ARRAY DIODEDA8,DA6,DA7,DA9 on MAIN BOARD,
01897189MA147-(TX)ARRAY DIODEDA3,DA2,DA5,DA4 on MAIN BOARD,
01012078SLR-332MG3FLED (GREEN)LED19 on PANEL-A BOARD1
01011656SLR-332VR3FLED (RED)LED21,LED13,LED12,LED6,LED20 on
00127367SPR-39MVWLED (RED/GREEN)LED22 on PANEL-A BOARD1
03564390SML-212DTT86LEDLED520,LED527,LED518,LED528,LED504,L
01121323DA204U T106DIODE ARRAYDA16 on JACK BOARD1
01121334DAN202U T106ARRAY DIODEDA10 on JACK BOARD1
00129767RD10M-T1B B2ZENER DIODED1 on JACK BOARD1
Q501 on PANEL-C BOARD
26 on JACK BOARD
DA4,DA2,DA1,DA3 on JACK BOARD,
DA503,DA505,DA502,DA501,DA504,DA51
3,DA512,DA511,DA510,DA509,DA508,DA5
07,DA506 on PANEL-C BOARD
DA7,DA6,DA8,DA9,DA11,DA12,DA13,DA
14,DA15,DA5 on JACK BOARD
21,D1,D19,D17,D16,D6,D2,D3,D20,D5,D15,
D7,D8,D10,D11,D12,D13,D14,D4 on PAN-
EL-A BOARD,
D204,D201,D203,D205,D206,D207,D208,D2
09,D210,D202 on PANEL-B BOARD
LED522 on PANEL-C BOARD
LED501,LED523,LED508,LED515 on PAN-
EL-C BOARD
ED8,LED7,LED5,LED4,LED3,LED1,LED17
on PANEL-A BOARD,
LED509,LED502,LED510,LED516,LED503
on PANEL-C BOARD
PANEL-A BOARD
ED526,LED525,LED524,LED521,LED519,LE
D517,LED514,LED513,LED512,LED511,LE
D507,LED505,LED506 on PANEL-C
BOARD
1
+1
10
4
+13
+4
4
+10
10
+28
1
+1
1
+4
13
+5
5
18
RESISTOR
00567112RPC05T 471 JMTL.FILM RESISTORR177,R169,R179,R167 on MAIN BOARD,
R27,R20,R100,R30,R26,R21,R28,R108,R29,R
92,R91,R84,R25 on JACK BOARD
00566967RPC05T 470 JMTL.FILM RESISTORR284,R292,R79,R282,R283,R337,R290,R285,
R400,R338,R401,R294,R293,R291,R289,R288,
R287,R286,R399 on MAIN BOARD,
R514,R513 on PANEL-C BOARD
01011856RPC05T 0R0 JMTL.FILM RESISTORR68,R412,R427,R429,R439,R456,R73,R411,R
41,L18,L17,L16,R147,R113,R87,R305,R136,R
140,R144,R157,R214,R419,R304,R410,R306,
R307,R308,R309,R397,R403,R409,R239,R141
on MAIN BOARD
,R160,R3,R227,R217,R178,R236,R99,R16,R73
,R58,R52,R37,R33,R19,R18,R97,R6,R185,R15
on JACK BOARD ,R522,R516,R523,R515 on
PANEL-C BOARD
00567067RPC05T 221 JMTL.FILM RESISTORR421,R422 on MAIN BOARD,
R125,R82,R81,R80,R79 on JACK BOARD 2 +5
00567556RPC05T 105 JMTL.FILM RESISTORR50,R99,R156 on MAIN BOARD,
R141 on JACK BOARD
00567478RPC05T 334 JMTL.FILM RESISTORR173,R216 on MAIN BOARD2
00567467RPC05T 274 JMTL.FILM RESISTORR230 on MAIN BOARD1
00567445RPC05T 184 JMTL.FILM RESISTORR170,R212 on MAIN BOARD2
00567412RPC05T 104 JMTL.FILM RESISTORR420,R227,R222,R211,R208,R199,R172,R415,
R416,R236,R417,R418,R168 on MAIN
BOARD,
R89,R131,R123,R116,R95,R83,R134,R172,R7
6,R142,R145,R157,R169,R183,R204,R209,R16
1 on JACK BOARD
4
+13
19
+2
33
+5
+18
3
+1
13
+17
17
Mar.2004
RESISTOR
00567289RPC05T 103 JMTL.FILM RESISTORR2,R6,R10 on EXP BASE BOARD,
R118,R119,R134,R139,R150,R164,R165,R166,
R174,R114,R176,R44,R188,R175,R110,R109,
R105
,R84,R82,R195,R43,R42,R40,R39,R25,R13,R4
14,R80,R437,R393,R395,R413,R428,R430,R3
92,R436,R446,R438,R445,R449,R453,R455,R
238,R396,R431,R266,R451,R244,R247,R390,
R243,R313,R358,R363,R364,R365,R381,R241
,R384,R387,R388,R248 on MAIN BOARD
,R38,R5,R10,R11,R14,R13,R2,R165,R106,R88
,R208,R207,R203,R202,R182,R96,R127,R86,R
135,R12,R148 on JACK BOARD ,R517 on
PANEL-C BOARD
00567389RPC05T 563 JMTL.FILM RESISTORR255,R256 on MAIN BOARD,
R149 on JACK BOARD
00567245RPC05T 472 JMTL.FILM RESISTORR193,R159,R161,R171,R53,R194,R196,R200,
R218,R228,R163 on MAIN BOARD,
R87 on JACK BOARD
00567378RPC05T 473 JMTL.FILM RESISTORR408,R229,R231,R234 on MAIN BOARD,
R105,R78,R136,R138,R146,R229,R230,R234,
R187 on JACK BOARD
00567201RPC05T 272 JMTL.FILM RESISTORR225,R205,R197,R232 on MAIN BOARD,
R150,R223,R174,R173 on JACK BOARD
00566934RPC05T 330 JMTL.FILM RESISTORR72,R350,R348,R346,R345,R344,R71,R349,R
74,R75,R76,R314,R323,R325,R326,R335,R34
3,R7,R450,R1,R2,R3,R347,R6,R368,R8,R10,R
63,R70,R435,R434,R433,R432,R4 on MAIN
BOARD
00567190RPC05T 222 JMTL.FILM RESISTORR133 on MAIN BOARD,
R102,R110 on JACK BOARD
00566923RPC05T 270 JMTL.FILM RESISTORR146,R145 on MAIN BOARD2
00566867RPC05T 100 JMTL.FILM RESISTORR441,R261,R260,R442,R262,R263 on MAIN
341,R300 on MAIN BOARD
00567178RPC05T 152 JMTL.FILM RESISTORR148 on MAIN BOARD,
R186 on JACK BOARD
00567312RPC05T 183 JMTL.FILM RESISTORR235 on MAIN BOARD1
00567023RPC05T 101 JMTL.FILM RESISTORR315,R316,R183,R246,R245,R187,R182,R181
,R58,R57,R51,R320,R318,R54,R321,R331,R36
9,R370,R371,R372,R375,R378,R454,R317 on
MAIN BOARD,
R184,R35,R45,R71,R77,R177,R231,R31,R156
on JACK BOARD,
R505,R501,R504,R507,R508,R510,R511,R502
on PANEL-C BOARD
00567156RPC05T 102 JMTL.FILM RESISTORR322,R319,R233,R226,R206,R198,R91 on
MAIN BOARD,
R7,R120,R224,R4,R85,R113,R225,R176,R155
on JACK BOARD
00567134RPC05T 681 JMTL.FILM RESISTORR55,R158,R101 on MAIN BOARD,
R213,R167,R152,R139,R74,R212,R129 on
JACK BOARD
01904956RR0816P-821-DMTL.FILM RESISTORR361 on MAIN BOARD1
01904945RR0816P-120-DMTL.FILM RESISTORR359 on MAIN BOARD1
02014945MCR50 JZH J 0R0MTL.FILM RESISTORR407 on MAIN BOARD1
03342845RR0816P-151-DMTL.FILM RESISTORR360 on MAIN BOARD1
02673401RR0816P-102-DMTL.FILM RESISTORR353,R357 on MAIN BOARD2
03239556RR0816Q-100-DMTL.FILM RESISTORR354 on MAIN BOARD1
03239523RR0816Q-390-DMTL.FILM RESISTORR355 on MAIN BOARD1
01896278MCR18EZHJ 2R2MTL.FILM RESISTORR273 on MAIN BOARD1
03018878RR0816P-471-DMTL.FILM RESISTORR356 on MAIN BOARD1
02673423RR0816P-162-DMTL.FILM RESISTORR351 on MAIN BOARD1
01457145EXBE10C103JRESISTOR ARRAYRA63,RA13,RA74,RA19,RA39,RA29,RA24,
RA22,RA51,RA17,RA78,RA14,RA61,RA11,
RA7,RA5,RA1,RA16,RA42 on MAIN
BOARD
03232623EXB28V0R0JXRESISTOR-ARRAYRA101 on MAIN BOARD1
03015056EXB2HV470JVRESISTOR-ARRAYRA18,RA15,RA12,RA23 on MAIN BOARD4
02904601EXB2HV104JVRESISTOR-ARRAYRA108 on MAIN BOARD1
02904445EXB2HV330JVRESISTOR-ARRAYRA4,RA28,RA21,RA10 on MAIN BOARD
,RA5,RA1,RA2,RA3,RA4 on PC CARD
BOARD
03015290EXB28V104JXRESISTOR-ARRAYRA109 on MAIN BOARD1
03015278EXB28V220JXRESISTOR-ARRAYRA98,RA100 on MAIN BOARD2
02898923EXBE10C104JRESISTOR-ARRAYRA104,RA106 on MAIN BOARD2
03015301R-ARRAY EXB28V330JXRESISTOR-ARRAYRA88,RA121,RA93,RA89 on MAIN BOARD4
03015289EXB28V103JXRESISTOR-ARRAYRA95,RA92,RA116,RA90,RA91,RA102,RA9
4 on MAIN BOARD
02456878EXB2HV220JVRESISTOR-ARRAYRA60,RA50,RA62,RA107,RA20,RA27,RA8,
RA34,RA36,RA37,RA40,RA56,RA54,RA52,
RA43,RA105,RA33,RA117,RA110,RA111,R
A103,RA9,RA115,RA3,RA99,RA97,RA118,
RA96,RA86,RA119,RA77,RA73,RA120 on
MAIN BOARD
62
+3
+1
+21
2
+1
11
+1
4
+9
4
+4
34
1
+2
6
18
1
+1
24
+8
+9
7
+9
3
+7
19
4
+5
7
33
18
Fantom-X8
RESISTOR
02457790MNR14 EOAB J 330RESISTOR-ARRAY2
01906678MNR14 EOAB J 103RESISTOR-ARRAYRA1,RA16 on JACK BOARD8
01906667MNR14 EOAB J 100RESISTOR-ARRAYRA25,RA24,RA6,RA4,RA3,RA2 on JACK
13749190SR50TR 100 JCARBON RESISTORR8,R7 on PANEL-A BOARD2
13749765T0SR25TRE 470 JCARBON RESISTORR23 on PANEL-A BOARD1
13749771T0SR25TRE 820 JCARBON RESISTORR22 on PANEL-A BOARD1
13749773T0SR25TRE 101 JCARBON RESISTORR2,R13,R4,R3,R1 on PANEL-A BOARD5
13749779T0SR25TRE 181 JCARBON RESISTORR17 on PANEL-A BOARD1
13749781T0SR25TRE 221 JCARBON RESISTORR21,R16 on PANEL-A BOARD2
13749797T0SR25TRE 102 JCARBON RESISTORR14,R19 on PANEL-A BOARD6
13749799T0SR25TR 122JCARBON RESISTORR15 on PANEL-A BOARD1
13749805T0SR25TRE 222 JCARBON RESISTORR6 on PANEL-A BOARD1
13749811T0SR25TRE 392 JCARBON RESISTORR5,R10 on PANEL-A BOARD2
13749821T0SR25TRE 103 JCARBON RESISTORR30,R28,R26,R18,R11,R24 on PANEL-A
13749837T0SR25TRE 473 JCARBON RESISTORR12 on PANEL-A BOARD1
13749839T0SR25TRE 563 JCARBON RESISTORR20 on PANEL-A BOARD1
13749859T0SR25TRE 394 JCARBON RESISTORR9 on PANEL-A BOARD1
00567290RPC05T 123 JMTL.FILM RESISTORR521 on PANEL-C BOARD1
00567367RPC05T 393 JMTL.FILM RESISTORR518 on PANEL-C BOARD1
00567456RPC05T 224 JMTL.FILM RESISTORR524 on PANEL-C BOARD1
00567501RPC05T 474 JMTL.FILM RESISTORR506,R509,R503,R512 on PANEL-C BOARD4
01450490NTH5G1M33B103JTHERMISTOR RESISTORR519 on PANEL-C BOARD1
03128889EXBV8V222JVRESISTOR-ARRAYRA502,RA503,RA504,RA501 on PANEL-C
15399561RPC18T 330 JCARBON RESISTORR61 on JACK BOARD 1
15399567RPC18T 560 JCARBON RESISTOR4
15399573RPC18T 101 JCARBON RESISTORR226 on JACK BOARD1
15399583RPC18T 271 JCARBON RESISTORR68,R67 on JACK BOARD2
15399565RPC18T 470 JCARBON RESISTORR221,R222,R219,R65,R64,R63,R62,R220 on
00566956RPC05T 390 JMTL.FILM RESISTORR69,R70 on JACK BOARD2
00567001RPC05T 750 JMTL.FILM RESISTORR126,R235 on JACK BOARD2
00567034RPC05T 121 JMTL.FILM RESISTORR75 on JACK BOARD1
00567078RPC05T 271 JMTL.FILM RESISTORR90,R72 on JACK BOARD2
00567089RPC05T 331 JMTL.FILM RESISTORR232,R153,R206,R168,R140,R130,R211 on
00567256RPC05T 562 JMTL.FILM RESISTORR119,R111,R112,R118 on JACK BOARD4
00567267RPC05T 682 JMTL.FILM RESISTORR32 on JACK BOARD1
00567323RPC05T 223 JMTL.FILM RESISTORR164,R180,R181,R163 on JACK BOARD4
00567345RPC05T 333 JMTL.FILM RESISTORR107,R94,R104,R101,R98 on JACK BOARD5
00567390RPC05T 683 JMTL.FILM RESISTORR109 on JACK BOARD1
00567401RPC05T 823 JMTL.FILM RESISTORR93 on JACK BOARD1
00567423RPC05T 124 JMTL.FILM RESISTORR103 on JACK BOARD1
15399501RPC18T 0R0 JMTL.FILM RESISTORR66 on JACK BOARD1
15399952MCR50JZH470 1/2WCHIP RESISTORR188,R121,R114,R189 on JACK BOARD4
00126134EXB-A10E103JRESISTOR ARRAYRA9,RA7,RA11,RA12,RA14,RA17,RA5 on
01906656MNR14 EOAB J 000RESISTOR-ARRAYRA19,RA18 on JACK BOARD2
BOARD
BOARD
BOARD
JACK BOARD
JACK BOARD
,R34,R170,R128,R210,R214,R233,R205,R215
on JACK BOARD
JACK BOARD
+2
22
+6
6
4
8
7
16
7
POTENTIOMETER
CAPACITOR
03126178EVUF2JFK3B14
03126167EVJY10FB6A24
03562256EVUF2AE20B14ROTARY POTENTIOMETERVR501 on PANEL-C BOARD1
02129534ECJ1VB1H102KCERAMIC CAPACITORC386 on MAIN BOARD,
C521,C520,C519 on PANEL-C BOARD
01674190ECUV1H150JCVCERAMIC CAPACITORC71,C27,C72,C164,C165,C263,C264,C440,C
441,C26 on MAIN BOARD
01674423ECUV1H471JCVCERAMIC CAPACITORC25,C24 on MAIN BOARD,
C140 on JACK BOARD
01674689ECJ1VF1H473ZCERAMIC CAPACITORC283,C318 on MAIN BOARD2
02126434ECHU1H821JX5POLYEST. CAPACITORC323,C310,C300,C328 on MAIN BOARD4
01899223ECHU1H102JX5POLYEST. CAPACITORC285,C277 on MAIN BOARD2
03346089ECHU1C682JX5POLYEST. CAPACITORC303,C332,C327,C316 on MAIN BOARD4
01904856ECEV1CA470WRCHEMICAL CAPACITOR2
03454790EEE1CA221PCHEMICAL CAPACITORC258,C253 on MAIN BOARD2
15369109ECEV0JA101SPCHEMICAL CAPACITOR8
15369152ECEV1CA100SRCHEMICAL CAPACITORC4,C3,C2,C6,C25,C5,C17 on EXP BASE
BOARD
03454789EEE1CA220WRCHEMICAL CAPACITORC284,C274 on MAIN BOARD2
03454812EEE1CA470SPCHEMICAL CAPACITORC363,C365 on MAIN BOARD2
03343045EEE0JA101SPCHEMICAL CAPACITORC375,C461,C459,C398,C395,C360,C358,C39
7 on MAIN BOARD,
C1 on PC CARD BOARD
02345145RV2-16V101M-RCHEMICAL CAPACITORC437 on MAIN BOARD1
02897045ECEV1CA220WRCHEMICAL CAPACITOR2
027834126SVP150 OS-CONCHEMICAL CAPACITORC244,C254 on MAIN BOARD2
01120301ECEV1CA221P 220UFCHEMICAL CAPASITOR2
03564345EEE1AA102PCHEMICAL CAPACITORC457,C445 on MAIN BOARD2
#02345201RV2-6V220MU-RR2CHEMICAL CAPACITOR4
03454912EEE1HA2R2SRCHEMICAL CAPACITORC292 on MAIN BOARD1
02015778ECEV1AA102PCHEMICAL CAPACITOR2
03458790EEE1CS100SRCHEMICAL CAPACITORC180,C149,C239,C273,C94,C31,C166,C150,
,C31,C13,C3 on PANEL-A BOARD
13519661DD104-989SL150J50CERAMIC CAPACITORC11,C10 on PANEL-A BOARD2
13529509DD106-999F103Z50CERAMIC CAPACITORC14 on PANEL-A BOARD1
02018701DD104-989SL680J50CERAMIC CAPACITORC16,C18,C26,C28 on PANEL-A BOARD4
13639150M0ECEA1CKS100B 10UF/16VCHEMICAL CAPACITORC6 on PANEL-A BOARD,
C301 on LCD BOARD,
C508 on PANEL-C BOARD
13639569M0ECEA1EKA470BCHEMICAL CAPACITORC22,C23 on PANEL-A BOARD2
13669266ECEA1EKS100BCAPACITORC9,C7 on PANEL-A BOARD,
C501 on PANEL-C BOARD
02018690R2A-16V101M-T2CHEMICAL CAPACITORC19,C17,C32,C8,C33 on PANEL-A BOARD,
C522 on PANEL-C BOARD
01674389ECUV1H221JCVCERAMIC CAPACITORC514,C515,C505,C516,C517,C513,C512,C51
1,C510,C518,C509,C504,C503,C502,C506,C5
07 on PANEL-C BOARD
00568456ECJ1VF1C474ZCERAMIC CAPACITORC106 on JACK BOARD1
01674167ECUV1H100DCVCERAMIC CAPACITORC138 on JACK BOARD1
01674212ECUV1H220JCVCERAMIC CAPACITORC22,C110,C23 on JACK BOARD3
00674423ECA0JM102B 1000U/6.3VCHEMICAL CAPACITORC9 on JACK BOARD1
01127078ECA0JM471BCHEMICAL CAPACITORC11,C3 on JACK BOARD2
01454889RA2-16V470MT2 470UF/16VCHEMICAL CAPACITORC155,C164 on JACK BOARD2
01900823RA2-16V100M-T2CHEMICAL CAPACITORC117 on JACK BOARD1
01902867RA2-25V101M-T2CHEMICAL CAPACITORC208,C161,C135,C146,C149,C154,C132,C16
01906501RA2-16V220M-T2CHEMICAL CAPACITORC156,C165,C137 on JACK BOARD3
02014912RA2-25V100MT2CERAMIC CAPACITORC182,C175,C209,C177,C186,C170,C105,C21
02894390RA2-25V330MC-T2CHEMICAL CAPACITORC214,C215,C217,C169,C219 on JACK
02900523EEE1CA101WPCHEMICAL CAPACITORC98,C100 on JACK BOARD2
13639552M0
13529132RPE132-901F104Z50CERAMIC CAPACITORC405,C403 on INVERTER BOARD2
01900834RA2-16V101M-T2CHEMICAL CAPACITORC404 on INVERTER BOARD1
INDUCTOR, COIL, FILTER
03125167SLF12565T-470M2R4CHOKE COILL1 on MAIN BOARD1
03566334EMI FILTER NFW31SP106X1E4L1
01565578N1608Z601T01FERRITE-BEADL36,L35,L34,L33,L32,L31,L30,L29,L28,L27,L
01909645EXCML16A270UFERRITE-BEADL4,L3,R237 on MAIN BOARD3
00903167N2012Z601T02 (CHIP)FERRITE-BEADL25,L24 on JACK BOARD2
ECEA1CU331B 16V/330UF CHEMICAL
3,C109,C14,C125,C63,C13,C2,C15,C16,C17,
C18,C19,C20,C5 on JACK BOARD
7,C207,C127,C130 on JACK BOARD
0,C173,C179,C184 on JACK BOARD
BOARD
CHEMICAL CAPACITORC67,C195,C71,C69 on JACK BOARD4
26,L8,L20,L24,L23,L7,L22,L6,L21,L25,L19,L
14,L13,L12,L11,L10,L9,L37,L5 on MAIN
BOARD
,L30,L21,L36,L23,L26,L27,L37,L29,L20,L31,
L32,L33,L34,L35,L28,L10,L1,L2,L3,L4,L5,L2
2,L7,L19,L11,L12,L13,L14,L15,L16,L17,L18,
L6 on JACK BOARD
21
11
11
5
29
+33
CRYSTAL, RESONATOR
00894034MA-406 16.000MHZ TE24CRYSTALX2 on MAIN BOARD1
15299170MC-406 32.768KHZCRYSTALX1 on MAIN BOARD1
01340745MA-406 12MHZCRYSTALX4 on MAIN BOARD1
02673134MA-406 16.9344MHZCRYSTALX3 on MAIN BOARD1
00894023MA-406 20.000MHZ TE24CRYSTALX1 on JACK BOARD1
ENCODER
01905467EVE GC1 F20 24BROTARY ENCODEREN501 on PANEL-C BOARD1
CONNECTOR
0323062354104-5092CONNECTORCN18 on MAIN BOARD,
0312606718FMN-BMTTN-A-TFTCONNECTORCN9 on MAIN BOARD,
0334585634FMN-BMTTN-A-TFTCONNECTORCN5,CN4 on MAIN BOARD2
13369570B2B-PH-K-S (2P)CONNECTORCN21 on MAIN BOARD1
13369562B15B-PH-K-S JSTCONNECTORCN22 on MAIN BOARD,
13369592B7B-XH-A(7P) JSTCONNECTORCN10 on MAIN BOARD,
0345747820FLT-SM1-TBCONNECTORCN20 on MAIN BOARD,
0312604534FMN-STK-ACONNECTORCN5,CN6 on EXP BASE BOARD2
02010078TX25-80P-6ST-E1CONNECTORCN4,CN3,CN2,CN1 on EXP BASE BOARD4
0278247810FMN-STKCONNECTORCN201 on PANEL-B BOARD1
0312603438FMN-STK-ACONNECTORCN2 on PANEL-A BOARD1
13369564B12B-PH-K-S JSTCONNECTORCN11 on PANEL-A BOARD,
02566489SM02(8.0)B-BHS-TBCONNECTORCN304 on LCD BOARD1
01349645S2(4-2.3)B-XH-ACONNECTORCN305 on LCD BOARD1
0312609040FMN-SMT-A-TFCONNECTORCN501 on PANEL-C BOARD1
13439311520314-2CONNECTORCN701 on AFT BOARD1
1336959852147-0310 3PINWIRE TRAPCN702 on AFT BOARD,
0190866722FE-BT-VK-NCONNECTORCN15 on JACK BOARD1
0190864516FE-BT-VK-NCONNECTORCN14 on JACK BOARD1
0278246710FMN-BTKCONNECTORCN6 on JACK BOARD1
0312607838FMN-BMTTN-A-TFTCONNECTORCN5 on JACK BOARD1
0312608940FMN-BMTTN-A-TFTCONNECTORCN7 on JACK BOARD1
03013989B4B-PH-K-S JST(PB FREE)CONNECTORCN8 on JACK BOARD1
02673145B2(4-2.3)B-XH-ACONNECTORCN404 on INVERTER BOARD1
13369556B8B-XH-A JSTCONNECTORCN401 on INVERTER BOARD1
8. 512 MB DIMM (for DIMM specifications, refer to Main Specifications)
9. Wave expansion boards: SRX series, 4 pcs.
10. Computer (with USB connector; OS may be Windows Me, Windows 2000,
or Windows XP)
11. Expression pedal (e.g., EV-5)
12. Test device for applying a force of 3(kgf) (e.g., push-pull gauge) or
Weight 3 kg
Test mode procedure
Before you begin Test mode, make sure that the power is turned off, detach the
EXP COVER from the bottom panel of the Fantom, and insert the DIMM and
expansion boards you provided.
Starting up Test Mode
1. Turn on the power of the Fantom.
2. Press the [MENU] button to display the Menu window.
3. Turn the [VALUE] dial to select “Utility,” and then press the [ENTER]
button.
4. Press the [4]
5. Press the buttons in the order of [SHIFT] ,[4],[5],[1],[8], and the LCD
display will show as follows.
fig.test725_70
When you press the [2] button (LINE TEST), the LCD display will show as
follows, and Test mode will start up.
25
Mar.2004
fig.test710_70
Basic operation in Test mode
Basic operation of the controls will be as follows.
[8]To the next test screen
[1]To the previous test screen
[SHIFT]+[8]Forcibly move to the next test screen
[SHIFT]+[1]Forcibly move to the previous test screen
[MENU]Select test items
When you enter the test item select screen, the LCD display will show as
follows.
fig.test563_70
14. Pad Adjustment
15. Pad Velocity Test
16. Pad Aftertouch Test
17. A/D Test
18. Keyboard Test
19. USB
20. Noise Test
21. Factory Reset
22. Completed
0. VERSION check
When you enter Test mode, you will begin from the VERSION check item.
fig.test710_70
Use the [VALUE] dial, [INC][DEC] buttons, or [CURSOR] up/down buttons
to select a test item, and press the [ENTER] button.
Test items
Test the following twenty items.
0. Version Check
1. Mute
2. Device
3. DIMM
4. Expansion Board
5. MIDI Test
6. Card
7. Encoder Test
8. Switch1 & LED Test
9. Switch2
10. LCD Test
11. Sound Test
12. D-Beam Adjustment
13. D-Beam
The LCD display shows the program version number.
All LEDs will light.
Press the [8] button to proceed to the next test item.
1. MUTE test
This tests the mute circuit on the jack board.
The LCD display will show as follows, and a built-in demo song will begin
playing.
fig.test710_70
Verify that an audio signal is being output from the [PHONES] jack and the
[OUTPUT A L/R] jacks.
Then verify that the audio signal is muted while you press the [4] button.
Press the [8] button to proceed to the next test item.
2. DEVICE test
This tests various devices located on the main board.
When you enter the DEVICE test, the LCD display will show as follows, and
device testing will begin automatically.
If all test results are OK, you will automatically proceed to the next test item.
fig.test714_70
If the test result is OK, you will automatically proceed to the next test item.
5. MIDI test
This tests MIDI connectivity.
When you enter the MIDI test without any MIDI cable connected between
MIDI IN and MIDI OUT, the LCD display will show as follows.
fig.test-midi-ng_70
3. DIMM test
This tests the DIMM socket and peripheral circuits.
When you enter the DIMM test, the LCD display will show as follows, and the
DIMM test will begin automatically.
fig.test713_70
If the test result is OK, you will automatically proceed to the next test item.
4. Expansion Board test
This tests the Expansion Board socket and peripheral circuits.
When you enter the Expansion Board test, the LCD display will show as
follows, and the Expansion Board test will begin automatically.
Use a MIDI cable to connect the MIDI IN and MIDI OUT .
If the test result is OK, you will automatically proceed to the next test item.
6. Card
This tests the PC CARD connector and peripheral circuits.
When you enter the Card test, the LCD display will show as follows.
fig.test716_70
Next insert the PC CARD (formatted; no protect label) into the PC card slot.
When the test result is OK, the display will indicate “Read/Write=OK
Please,Remove The Card”.
When you remove the inserted PC CARD, you will automatically proceed to
the next test item.
27
Mar.2004
7. Encoder
When you enter the Encoder test, the LCD display will show as follows.
fig.test659_70
Continue turning the [VALUE] dial toward the left, and verify that the LCD
display indicates “Left: 72 OK.”
Next, continue turning the [VALUE] dial toward the right, and verify that the
LCD display indicates “Right: 72 OK.” You will then automatically proceed to
the next test item.
8. Switch1 & LED
This tests the operation of LED-equipped switches.
When you enter the Switch 1 & LED test, the LCD display will show as
follows.
fig.test625_70
9. Switch2
This tests the operation of switches that were not checked in the Switch1 &
LED test.
When you enter the Switch2 test, the LCD display will show as follows.
fig.test684_70
One by one, press each switch shown in the LCD display.
Verify that the indication in the LCD display for the corresponding switch
becomes lighter.
When the indications of all switches have become lighter and the test results
are OK, you will automatically proceed to the next test item.
10. LCD
This tests the operation of the LCD display.
When you enter the LCD test, the LCD display will show as follows.
fig.test645_70
One LED-equipped panel switch will light.
When you press that switch, the next LED-equipped switch will light.
Repeat this until all switches are OK, and you will automatically proceed to the
next test item.
Pressing two or more switches simultaneously is not valid.
Switches with an LED window will produce the OK result when they are
pressed once. In the case of switches (without a window) located next to
exposed LEDs, the OK result will be produced when you press the switch the
number of times corresponding to the number of exposed LEDs.
When the display for all switches has become lighter, and the test results are
OK, you will automatically proceed to the next test item.
28
When you press the [8] button you will proceed to the eight-level grayscale
test. The LCD display will show as follows.
fig.test646_70
Turn the [LCD CONTRAST] knob, verify that eight-levels of grayscale are
displayed, and set the knob to the optimal contrast.
When you press the [8] button you will proceed to the collor display test. The
Fantom-X8
LCD display will show as follows.
fig.test-lcd1_70
When you press the [8] knob, you will proceed to the all-pixels-displayed test.
The LCD display will show as follows.
fig.test647_70
Verify that the LCD display shows a sawtooth wave and another sawtooth
wave (of inverted phase relative to the upper one) below, as follows.
fig.test-sound1_70
Next you will test the circuitry of the [OUTPUT A R] jack.
Connect the stereo side of the PCS-31 to the [OUTPUT A R] jack, connect the
PCS-31’s monaural L channel to the [INPUT L] jack, and connect the PCS-31’s
monaural R channel to the [INPUT R] jack. Turn the [VOLUME OUTPUT]
knob and the [VOLUME INPUT] knob all the way toward the right (MAX).
Verify that the LCD display shows a sine wave above and another sine wave
(of inverted phase relative to the upper one) below, as follows.
fig.test-sound2_70
Verify that there are no missing dots, and that the darkness is consistent.
When you press the [8] button, you will proceed to the all-pixels-off test. The
LCD display will show as follows.
fig.test648_70
Verify that there is no obtrusive dirt or dust.
Press the [8] button to proceed to the next test item.
11. Sound test
This tests the audio input/output circuitry.
First you will test the [OUTPUT A L (MONO)] jack and [INPUT L/R] jack
circuitry.
Connect the stereo side of the PCS-31 to the [OUTPUT A L (MONO)] jack,
connect the PCS-31’s monaural L channel to the [INPUT L] jack, and the PCS31’s monaural R channel to the [INPUT R] jack. Insert a dummy plug into the
[OUTPUT A R] jack, and turn the [VOLUME OUTPUT] knob and [VOLUME
INPUT] knob all the way toward the right (MAX).
When you press the [8] button you will proceed to the test of the [OUTPUT B
L/R] jack circuit.
Use an audio cable to connect the [OUTPUT B L] jack to the [INPUT L] jack,
and the [OUTPUT B R] jack to the [INPUT R] jack. Turn the [VOLUME INPUT]
knob all the way toward the right (MAX).
Verify that the LCD display shows a sawtooth wave above and a sine wave
below, as follows.
fig.test-sound3_70
When you press the [8] button you will proceed to the test of the [DIGITAL
INPUT OUTPUT] jacks.
Use a COAXIAL (pin) cable to connect the [DIGITAL INPUT] and [DIGITAL
OUT] jack.
29
Mar.2004
Verify that the LCD display shows a sawtooth wave above and a sine wave
below, as follows.
fig.test-sound4_70
Press the [8] button to proceed to the next test item.
12. D-Beam Adjustment test
This adjusts the sensitivity of the [D BEAM] controller.
This adjustment sets the optimal sensitivity for the controller by making
adjustments for two distances from the [D BEAM] controller; at 5 cm and at 45
cm.
Before you begin this test: The location of the Fantom must satisfy the
following conditions.
Do not place objects nearby the Fantom. (It must be at least 30 cm from
surrounding objects.)
Place the Fantom at a distance from large flat surfaces such as ceiling or walls.
(It must be at least 100 cm away from such surfaces.)
Do not place the Fantom where strong light, such as direct sunlight or electric
light, can fall on it.
When you enter the D-Beam Adjustment test, the LCD display will show as
follows.
fig.test618_70
13. D-Beam test
This tests the operation of the [D BEAM] controller.
When you begin the D-Beam test, the LCD display will show as follows.
fig.test623_70
First you will test the [D BEAM] controller.
The LCD display will show “Max.”
Place your hand above the [D BEAM] controller, and move that hand
downward.
Verify that the LCD display shows the maximum value (L 127) when your
hand is approximately 5 cm from the surface of the panel.
If the test result is OK, the LCD display will show “Min.”
Place your hand above the [D BEAM] controller, and move that hand upward.
Verify that the LCD display shows the minimum value (L 0) when your hand
is approximately 45 cm from the surface of the panel.
If the test result is OK, you will automatically proceed to the next test item.
14. Pad Adjustment
This adjusts the [DYNAMIC PAD] sensitivity.
This adjustment sets the optimal [DYNAMIC PAD] sensitivity relative to a
force of 3 (kgf) applied to the [DYNAMIC PAD].
When you enter the Pad Adjustment test, the LCD display will show as
follows.
fig.test766_70
First make the “5 cm” setting for the [D BEAM] controller.
The LCD display will indicate “Low (5cm).”
Place your hand in parallel with the panel surface at a vertical distance of 5 cm
from the [D BEAM] controller, and press the [ENTER] button.
Do not move your hand while the lower part of the LCD display shows “Now
Adjusting...”
When the setting has been completed, you will automatically proceed to the
next setting.
Make the “45 cm” setting for the [D BEAM] controller.
The LCD display will indicate “High (45cm).”
Place your hand in parallel with the panel surface at a vertical distance of 45
cm from the [D BEAM] controller, and press the [ENTER] button.
Do not move your hand while the lower part of the LCD display shows “Now
Adjusting...”
When the setting has been completed, you will automatically proceed to the
next test item.
30
When you press the [ENTER] button, every [DYNAMIC PAD] will blink, and
the LCD display will show as follows.
Fantom-X8
fig.test-pad-adj1_70
Using the push-pull gauge you provided, apply pressure of 3 (kgf) to
[DYNAMIC PAD 4].
When you press the [ENTER] button, the setting will be saved and you will
automatically proceed to the next test item.
15. Pad Velocity
This tests [DYNAMIC PAD] operation.
When you enter the Pad Velocity test, every [DYNAMIC PAD] will blink, and
the LCD display will show as follows.
fig.test632_70
fig.test769_70
Strongly and slowly press each [DYNAMIC PAD] from [1] through [16].
Verify that the LED of the [DYNAMIC PAD] you press changes from blinking
to dark, and that in the LCD display the bar graph for the corresponding
button becomes lighter.
If the test result is OK, you will automatically proceed to the next test item.
17. A/D
This tests the operation of each rotary control and slide control.
When you enter the A/D test, the LCD display will show as follows.
fig.test606_70
Lightly press each [DYNAMIC PAD] from [1] through [16].
Verify that the LED of the [DYNAMIC PAD] you press changes from blinking
to lit, and that in the LCD display the “L” indication for the corresponding
button becomes lighter.
Strongly press each [DYNAMIC PAD] from [1] through [16].
Verify that the LED of the [DYNAMIC PAD] you press changes from lit to
dark, and that in the LCD display the “H” indication for the corresponding
button becomes lighter.
If the test result is OK, you will automatically proceed to the next test item.
16. Pad Aftertouch
This tests [DYNAMIC PAD] operation.
When you enter the Pad Velocity test, every [DYNAMIC PAD] will blink, and
the LCD display will show as follows.
One by one, operate all controls (other than the [VOLUME OUTPUT] knob and
the [VOLUME INPUT] knob), including the bender, aftertouch, [CONTROL]
jack (connect an expression pedal such as the EV-5), and [HOLD] jack (connect
an expression pedal such as the EV-5), to adjust through their variable range
from MAX to MIN.
Verify that the corresponding indicator in the LCD display becomes lighter.
When all indicators have become light, and the test results are OK, you will
automatically proceed to the next test item.
31
Mar.2004
18. Keyboard
This tests the keyboard.
When you enter the keyboard test, the LCD display will show as follows.
fig.test-kbd1_70
Perform the eight-note check. Play the keyboard to check.
Also verify that the volume changes according to the strength with which you
press the key.
When you press the [8] button, the sound will change, and the LCD display
will show as follows.
fig.test-kbd2_70
Connect a USB cable to your computer (one that has a USB connector; the OS
can be either Windows Me, Windows 2000, or Windows XP).
If the test result is OK, the display will indicate “Status: Connect USB Test
Completed!”
On your computer, use the Safely Remove Hardware icon shown in the
taskbar at the lower right of the screen to break the connection with the
Fantom-X.
Press the [8] button to proceed to the next test item.
20. Noise test
fig.test806_70
Perform the two-note check. Play the keyboard to check.
Press the [8] button to proceed to the next test item.
When you do not check the all key, you can not proceed to the next test items.
19. USB
This tests USB operation.
When you enter the USB test, the LCD display will show as follows.
fig.test760_70
1. Cheak the nosie is soundig or not.
2. Press the [8] button to proceed to the next test item.
21. Factory Reset
This perform a Factory Reset.
The LCD display will show as follows.
fig.test756_70
When you press the [ENTER] button, the LCD display will show as follows,
and the factory reset will be executed automatically.
32
Fantom-X8
fig.test778_70
When the factory reset is completed, the LCD display will show as follows,
and you will exit Test mode.
fig.test719_70
SYSTEM SOFTWARE UPDATE
PROCEDURE
The Fantom-X uses flash memory as its program ROM, and can be updated
using either of the following two methods.
1. Updating from a computer via a
USB cable
(Time required: approximately 3 minutes)
2. Updating from PC CARD via the
Fantom’s PC card slot
(Time required: approximately 3 minutes)
1. Updating from a computer via
a USB cable
Required items
1. UPDATE DATA FOR SERVICE CD-ROM (#17041422)
2. A computer (with a USB connector; the OS can be either Windows Me,
Windows 2000, or Windows XP)
* You cannot use a Mac under any circumstances.
3. One PC card (64 MB or more free space) or PC
4. Used to back up user data
5. USB cable
If user memory contains important data, save the data (refer to Saving and
Loading User Data) before you perform the update procedure.
Turn off the power of the Fantom.
RESTORING THE FACTORY
SETTINGS
This restores all data in the Fantom-X to the factory-set condition (Factory
Reset).
If there is important data you’ve created that’s stored in the Fantom-As’s
internal memory, all such data is discarded when a Factory Reset is performed
(the data of the internal user memory will be lost). If you want to keep the
existing data, save it on a PC CARD or save it on via USB to your computer
1. Press [MENU] to open the Menu window.
2. Pressorto select “Utility,” and then press [ENTER].
3. Press [3 (Factory Reset)].
A message will ask confirmation.
4. Press [8 (Exec)] to execute the Factory Reset.
* To cancel, press [7 (Cancel)].
5. When the display indicates “Please Power Off,” turn the power off, then
on again.
Procedure
1. Turn on the power of the Fantom-X.
2. Press the [MENU] button to access the Menu window.
3. Use the [CURSOR] up/down buttons to select “System,” and then press
the [ENTER] button.
4. The System Setup screen will appear, and the LCD display will show as
follows.
fig.update01_70
5. Press the [4] button “System Info”.
6. Use [1 ()] [2 ()] to select “Version Info.” The Version Info screen
will appear, and the LCD display will show as follows.
33
Mar.2004
fig.update02_70
7. Press buttons in the order of [SHIFT]->[7]->[8]->[7]->[8].
8. The “Service Utility” screen will appear, and the LCD display will show
as follows.
fig.update03_70
9. When you press the [1] button, the [Program Update Mode (USB)] screen
will appear, and the LCD display will show as follows.
fig.update04_70
fig.update05_70
At this time “ [USB STATUS] “ will indicate the status of the USB connection.
[USB STATUS] Disconnected.The computer is not connected.
[USB STATUS] connected.The Fantom-X is connected to the computer.
[USB STATUS] Receiving..Data is being received from the computer.
12. Turn on the power of the computer.
13. Use a USB cable to connect the computer to the Fantom-X. (The computer
will detect the Fantom-X as a removable disk drive.)
Verify that the LCD display of the Fantom-X indicates “ [USB STATUS]
connected. “
14. Insert the UPDATE CD-ROM (#17041422) into your computer, and
navigate to the “Roland” folder of the CD-ROM.
15. Copy the file “fanx.bin” file (located within the “Roland” folder) to the
Fantom-X (removable disk).
The Fantom-X will receive the data from the computer.
Verify that the LCD display of the Fantom-X indicates “ [USB STATUS]
Receiving.. “
When the LCD display of the Fantom-X shows the “ [USB STATUS]
Connected. “ indication for ten seconds or longer, this indicates that the copy
has been completed.
16. On your computer, use the Safely Remove Hardware icon in the taskbar
at the lower right of the screen to disconnect the Fantom-X from your
computer.
17. Press the [ENTER] button. After a time, the display will indicate
“Completed. Please, PowerOff.” The update procedure has been
completed.
18. Turn the power of the Fantom-X off and then on again, and perform the
version check and execute Test mode.
10. Press the [ENTER] button. The LCD display will show “Initializing....”
and will then show as follows.
11. If you decide to cancel the update, press the [EXIT] button before you
press the [ENTER] button. (If you execute the update, all user data will be
erased.)
34
Cautions when updating via USB
After you have pressed the [ENTER] button at the end of the procedure
described above, never turn off the power of the Fantom-X until the indication
of “Completed. Please, PowerOff.” has appeared. If the power is turned off
during this time, the program will be erased.
You must restart your computer before you begin the update procedure.
2. Updating from PC CARD via
the Fantom’s PC card slot
Required items
• UPDATE DATA FOR SERVICE CD-ROM (#17041420)
• Computer (the OS can be either Windows Me, Windows 2000, or
Windows XP)
* You cannot use a Mac under any circumstances.
• PC cards (one with 32 MB or more free space, one with 32 MB or more
free space (used to back up user data))
* In addition, substitution to PC is possible for user data back up.
• PC CARD reader/writer
If user memory contains important data, save the data (refer to Saving and
Loading User Data) before you perform the update procedure.
Fantom-X8
Procedure
1. Create an update card.
2. Turn on the power of your computer.
3. Insert a 32 MB or larger PC card into the PC CARD reader/writer
connected to your computer, and format it.
4. Insert the UPDATE CD-ROM (#17041420) into your computer, and
navigate to the “Roland” folder within the CD-ROM.
5. Copy the entire “Roland” folder with its contents onto the PC card.
6. Turn on the power of the Fantom-X.
7. Press the [MENU] button to access the Menu window.
8. Use the [CURSOR] up/down buttons to select “System,” and then press
the [ENTER] button.
9. The System Setup screen will appear, and the LCD display will show as
follows.
fig.update06_70
fig.update08_70
14. Press the [2] button to access the [Program Update Mode (CARD)] screen.
The LCD display will show as follows.
fig.update09_70
10. Press the [4] button “System Info.”
11. Use [1 (.)] [2 (,)] to select “Version Info.” The Version Info screen will
appear, and the LCD display will show as follows.
fig.update07_70
12. Press the buttons in the order of [SHIFT]->[7]->[8]->[7]->[8].
13. The “Service Utility” screen will appear, and the LCD display will show
as follows.
15. Press the [ENTER] button. After a time, the display will indicate
“Completed. Please, PowerOff.” The update procedure has been
completed.
fig.update10_70
16. If you decide to cancel the update procedure, press the [EXIT] button
before you press the [ENTER] button.
17. Turn the power of the Fantom-X off and then on again, and perform the
version check and execute Test mode.
Cautions when updating via PC card
After you have pressed the [ENTER] button at the end of the procedure
described above, never turn off the power of the Fantom-X until the indication
of “Completed. Please, PowerOff.” has appeared. If the power is turned off
during this time, the program will be erased.
You must restart your computer before you begin the update procedure.
35
Mar.2004
KEYBOARD PARTS LIST
For the procedure for repairing the keyboard section, see the PA-5 service noted(P/No. 17059023)
fig.keyboard-pl
SCREW M3X10 BINDING B-TITE FE ZC
SCREW 3X6 BINDING TAPTITE P FE ZC
* :Item 15 marked * is included in each unit of 14.
The following parts are not included the Keyboard Assy.
36
Fantom-X8
37
Mar.2004Fantom-X8
BLOCK DIAGRAM
fig.block
PANEL-A,B,C BOARD
PCMCIA BOARD
PC CARD
LCD UNIT
COLOR LCD
STN
QVGA
320x240dot
VRD-Beam
DynamicPAD
ENC
SW
LED
X1
32.768kHz
X2
16.000MHz
CPU
IC1
SH-3/7706
128MHz
X3
16.9344MHz
SDRAM
IC106
64Mbit
Effect RAM
DIMM
PC133/100
SDRAM
IC2,IC6
128Mbit x 2
Work RAM
64MHz bus
512Mbit NAND
TC58DVM92A1TG
32bit
buffer
32bit/16bit
WX
IC102
12bit
R03236690
16bit
32bit
SDRAM bus
Wave RAM
SDRAM
IC20,IC24
128Mbit x 2
Wave RAM
MAIN BOARD
Flash ROM
Program,User
8bit
Mask ROM
IC28,IC33,IC103,IC104
128Mbit x 2
Wave ROM
Flash ROM
IC19IC53
MBM29LV160BE70
16Mbit
Program ROM
8bit16bit
buffer
USBC
IC56
M66291GP
Wave Bus
EXP BASE BOARD
SRX
x4
16bit
LCDC
IC49
S1D13705
X4
12.000MHz
DACwithDIR
IC75
CODEC
AK4527B
IC60
A/D2ch,D/A6ch
DIT
IC62
LCDBOARD
DC-AC INVERTER
DHE1105-5VE
16bit
USB
UDA1351TS
TC9271FS
X1
20.000MHz
CPU
IC2
H8/3061
20MHz
8bit
KeyScan
IC20
SSC1080
Keyboard
SK9/PA5
(with aftertouch)
CONTROL
HOLD
INOUTTHRU
PEDAL
MIDI
Digital In COAX
PHONES/OUT
OUTPUT-A
OUTPUT-B
AUDIO/IN
Digital Out COAX
JACK BOARD
OUTPUT
VOLUME
INPUT
VOLUME
39
Mar.2004
CIRCUIT BOARD(MAIN 1)
fig.b-x678-main1
40
View from components side
Fantom-X8
CIRCUIT BOARD(MAIN 2)
fig.b-x678-main2
View from foil side
41
Mar.2004Fantom-X8
CIRCUIT DIAGRAM(MAIN 1)
fig.c-x678-main1
DQ9
DQ8
DQ7
DQ6
DQ5
DQ4
DQ3
DQ2
DQ1
DQ0
VDD
VSS
VSS
Q2
RT1P141C
NIU
1
D1
45
43
41
39
36
34
32
30
44
42
40
38
35
33
31
29
37
C93
0.1
27
46
23
BD[15..0]
BA[15..0]
BA0A22
BD7
BD6
BD5
BD4
BD3
BD2
BD1
BD0
+
D3.3
D
Q4
DTC114EUA
1
D
NIU
FlashROM
16Mbit
C94
EEE-S@SR
10/16
XFLVID
A16
XCARD_SELECT
XDREQ0
XDACK0
XUSBCCS
XWX16CS
CKIO
LCDCLK
XWE1
XRD
XBCS2
XCE1A
XCE2A
XCE2B
XEXO
XSMBUS
XNDBUS
XSMNDCTL
EEPCS5
EEPCS4
EEPCS3
EEPCS2
EEPCS1
EEPCS0
XBWE0
XBWE1
XBRD
XLCDCCS
BA[15..0]A[25..0]
A16
XCARD_SELECT
XDREQ0
XDACK0
XUSBCCS
XWX16CS
CKIO
LCDCLK
XWE1
XRD
XBCS2
XCE1A
XCE2A
XCE2B
XEXO
XSMBUS
XNDBUS
XSMNDCTL
EEPCS5
EEPCS4
EEPCS3
EEPCS2
EEPCS1
EEPCS0
XBWE0
XBWE1
XBRD
XLCDCCS
CN1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
16FMN-BMTTN-TF
NIU
H-UDI
+
5D
18
TXD2
RTS2
TXD0
RXD2
RXD0
CTS2
+
5D
147
C52
0.1
IC9G
TC74VHCT04AFT
SW9B
ESD170202
NIU
10
R50
1M
IC16A
17
R55
680
14
C71
15p
D
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
27
36
C53
0.1
D
20
1
2
C72
Power
AUDATA0
AUDATA1
AUDATA2
AUDATA3
XAUDSYNC
TCK
TMS
XTRST
TDI
TDO
XASEBRKAK
XRST
AUDCK
D
RA90
10k
R315
45
100
R317
100
R320
100
+
D3.3
147
IC10G
HD74LV04AT
SW10B
ESD170202
NIU
20
10
DD
IC89
P2027A-08TR
XIN/CLK
XOUT
IC16C
62
IC16B
35
X2
16.000MHz
15p
D
C73
0.1
IC16D
TC7WU04FU
+
5D
R5
NIU
12
LED1
SML-310LT
NIU
D
IC9A
IC9C
IC9E
12
IC10A
56
IC10C
1110
IC10E
D
MODOUT
MRA3VSS4SSON
SR0
5
7
R52
NIU
R56
NIU
+
D3.3
84
D
12
IC9B
56
IC9D
1110
IC9F
34
98
1312
D3.3
NMI
+
D3.3
8
VDD
D
CPUCLK
+
D3.3
12
RA1
10k
12
RA7
10k
AUDATA0
AUDATA1
AUDATA2
AUDATA3
XAUDSYNC
XTRST
TMS
TCK
TDI
TDO
XASEBRKAK
XRST
AUDCK
+
D3.3
RA91
10k
18
34
98
1312
IC10B
IC10D
IC10F
+
R40
10k
SW3
SKQMAK
NIU
12
D
C385
0.1
6
LCDCLK
XWE3
3
XWE2
4
XWE1
5
XWE0
6
XRD
7
RD/XWR
8
XCS2
910
XCS3
XCE1B
3
XCE1A
4
XCS4
5
XCS0
6
XCE2A
7
XCE2B
8
XRASL
910
XCASL
12
3
4
RA14
5
10k
6
7
8
910
12
3
4
RA17
5
10k
6
7
8
910
SW9A
1
3
ESD170202
D
NIU
E10A mode
R44
10k
SW4
SKQMAK
NIU
27
36
45
DEBUG SW 2
PLAY_RED
PLAY_GREEN
SW10A
1
3
ESD170202
NIU
D
GDBmode
SDA
DIRERR
D
R339
22
CPUCLK
R340
22
LCDCLK
+
D3.3
+
D3.3
+
D3.3
2
+
D3.3
12
D
+
D3.3
2
XWE3
XWE2
XWE1
XWE0
XBBIOIS16
D3.3
XDACK0
XAUDSYNC
AUDATA3
AUDATA2
AUDATA1
AUDATA0
XTRST
TMS
TCK
TDI
TDO
XASEBRKAK
R241
10k
R25
10k
+
D3.3
R43
10k
XIREQ2
XPCMCIA-IRL
XWXINT
+
D3.3
R428
10k
RD/XWR
XRD
XCE1B
XCE1A
XCS4
XCS0
R3
XCS3
R4
XCS2
XCE2B
XCE2A
CKE
XCASL
XRASL
+
R13
EEPSEL2
EEPDO
XFLWP
XCD_DETECT
+
D3.3
XRST
R449
+
D3.3
10k
R456
D
D3.3
R429
0
EEPDI
45
36
27
18
45
36
27
18
R343
R6
R7
R8
33
R10
33
10k
R314
C24
C25
C26
D
32.768kHz
C27
15p
D
EEPSK
SCL
CKIO
R316
R318
R319
R321
R322
XWPSW
R39
R41
R42
0
+
Big endian
area0=8bit
area0=8bit
clockMODE1
clockMODE1
clockMODE1
If an incorrect operation is performed, or if processing could not be performed as you specified, an error message will appear. Refer to the
explanation for the error message that appears, and take the appropriate action.
Message
Cannot Edit Preset Sample!
Card Not Ready!
Data not found
Empty Pattern
Empty Sample!
Empty Song!
File Name Duplicate
Illegal File!
Memory Damaged!
Memory Full!
MIDI Offline!
No More Note Numbers!
No More Sample Numbers!
No More Song Numbers!
Now Playing!
Permission Denied!
Playback Tempo Range Over
Recording Parameter Error
Rec Over Flow
Sample Length Too Short!
Sample Memory Full!
Song Full
Song Format Error
Song Not Found
Too Many Sample Selected!
Unformatted!
You Cannot Assign
You Cannot Copy This Message
You Cannot Erase This Message
You Cannot Move This Message
You Cannot Quick Play S-MRC
Song
Rhythm Note Range Over!
MeaningAction
This is a preset sample, and therefore cannot be edited.—
A memory card is not inserted in the slot.Insert a memory card into the slot.
The data for placement is not specified.—
The Pattern has no data in it, so the Pattern Call message
cannot be recorded in Step Recording.
The sample contains no data.Select a sample that contains data.
The song has not been recorded, and therefore cannot be
played.
A file with the same name already exists.Delete the file bearing the same name from the disk,
The Fantom-X cannot use this file.—
The contents of memory may have been damaged.Please perform the Factory Reset operation.
Saving is not possible because there is insufficient space
in the user area or memory card.
There is a problem with the MIDI cable connection.Check that the MIDI cable has not been disconnect-
A maximum of 16 different note numbers can be used in
one style of the arpeggio/rhythm function.
The sample cannot be divided any further.Erase unneeded samples in order to allocate 256 or
Since fewer than 256 consecutive sample numbers are
vacant, no further sampling is possible.
No more songs can be saved. A maximum of 256 songs
can be handled simultaneously for both the user bank
and card bank.
Since the Fantom-X is playing, this operation cannot be
executed.
The file is protected.—
Tempo values exceed the allowable limit, and data is
created in which the closest time available within the allowable range is specified.
You are attempting to begin recording after a looped
segment.
Since a large amount of recorded data was input all at
once, it could not be processed correctly.
The sample is too short, and cannot be edited correctly.If the sample is extremely short, editing may not
Since there is insufficient sample memory, no further
sampling or sample editing is possible.
Since the maximum number of notes that can be recorded in a song or pattern has been exceeded, no further recording/editing is possible.
This song is damaged.This song cannot be used.
The selected song cannot be found.—
The operation cannot be executed, since marks are assigned to more than one sample.
The memory card is in an unsupported format.Format the memory card.
The sample cannot be assigned to a pad.Assign To Pad requires that all pads be playing a
This message cannot be copied.—
This message cannot be erased.—
This message cannot be moved.—
This is a SuperMRC song; it cannot be played back in
Quick Play.
The pad selected for Assign To Pad is outside the range
of the rhythm set.
—
Select a song that contains data.
and if overwriting and saving the data, merely save
the file. If you do not want to delete the file with the
same name from the disk, either save the file with a
different name.
If this does not resolve the problem, please contact
your dealer or the nearest Roland Service Center.
Delete unneeded data.
ed or broken.
Please delete unneeded notes.
more consecutive sample numbers.
Please delete unneeded songs.
Stop playback before you execute the operation.
—
You are attempting to begin recording within or before a looped segment.
Reduce the amount of recorded data.
produce the desired result.
Erase unneeded samples.
Use the track edit Delete or Erase commands to remove unneeded data from the song/pattern that
you are recording/editing.
Either clear the marks, or mark only one sample.
rhythm set.
Assign a rhythm set to the Pad part.
Turn off the RPS function.
Turn off the rhythm switch.
Turn off the ARPEGGIO/RHYTHM function.
Save the data as an MRC Pro song.
Select a pad that is within the range of the rhythm
set.
80
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.