Rockwell Automation 20B-70 User Manual

This workbook is Publication #
These records can be printed to provide a written record of parameter changes made to a PowerFlex 70 or PowerFlex 700 drive.
PFLEX-IN002A-EN-P
Last Reveision 1/21/02
Some manpulation of the spreadsheets may be necessary based on you selection of a printer.
Identity
S.M.A.R.T. Start
Parameter Setup
Customer Name ____________________
Plant ____________________
Machine # ____________________
Process Number ____________________
Other Data ____________________
Date Programmed ____________________
SW Version ____________________
Drive Cat # ____________________
Drive Ser # ____________________
40 Motor Type Induction 41 Motor NP Volts Based on Drive Rating 42 Motor NP FLA Based on Drive Rating 43 Motor NP Hertz Based on Drive Cat. No. 44 Motor NP RPM 1750 RPM 45 Motor NP Power Based on Drive Rating 46 Mtr NP Pwr Units Based on Drive Rating 47 Motor OL Hertz Motor NP Hz/3 48 Motor OL Factor 1.00 53 Torque Perf Mode Sensrls Vect 61 Autotune Calculate 62 IR Voltage Drop Based on Drive Rating 63 Flux Current Ref Based on Drive Rating 81 Minimum Speed 0.0 Hz 82 Maximum Speed 50.0 or 60.0 Hz 83 Overspeed Limit 10.0 Hz 90 Speed Ref A Sel Analog In 2 91 Speed Ref A Hi [Maximum Speed]
92 Speed Ref A Lo 0.0 Hz 140 Accel Time 1 10.0 Secs 142 Decel Time 1 10.0 Secs 201 Language Not Selected 320 Anlg In Config 0 321 Anlg In Sqr Root 0 322 Analog In 1 Hi 10.0 Volt 323 Analog In 1 Lo 0.0 Volt 324 Analog In 1 Loss Disabled 361 Digital In1 Sel Stop - CF 362 Digital In2 Sel Start
Par Parameter Name Factory Default Programmed Value Par Parameter Name Factory Default Programmed Value
288 Stop Owner Read Only 1 Output Freq Read Only 289 Start Owner Read Only 2 Commanded Freq Read Only 290 Jog Owner Read Only 3 Output Current Read Only 291 Direction Owner Read Only 4 Torque Current Read Only 292 Reference Owner Read Only 5 Flux Current Read Only 293 Accel Owner Read Only 6 Output Voltage Read Only 294 Decel Owner Read Only 7 Output Power Read Only 295 Fault Clr Owner Read Only 8 Output Powr Fctr Read Only 296 MOP Owner Read Only 9 Elapsed MWh Read Only 297 Local Owner Read Only 10 Elapsed Run Time Read Only 300 Data In A1 0 11 MOP Frequency Read Only 301 Data In A2 0 12 DC Bus Voltage Read Only 302 Data In B1 0 13 DC Bus Memory Read Only 303 Data In B2 0 16 Analog In1 Value Read Only 304 Data In C1 0 17 Analog In2 Value Read Only 305 Data In C2 0 26 Rated kW Read Only 306 Data In D1 0 27 Rated Volts Read Only 307 Data In D2 0 28 Rated Amps Read Only 310 Data Out A1 0 29 Control SW Ver Read Only 311 Data Out A2 0 40 Motor Type Induction 312 Data Out B1 0 41 Motor NP Volts Based on Drive Rating 313 Data Out B2 0 42 Motor NP FLA Based on Drive Rating 314 Data Out C1 0 43 Motor NP Hertz Based on Drive Cat. No. 315 Data Out C2 0 44 Motor NP RPM 1750 RPM 316 Data Out D1 0 45 Motor NP Power Based on Drive Rating 317 Data Out D2 0 46 Mtr NP Pwr Units Based on Drive Rating 320 Anlg In Config 0 47 Motor OL Hertz Motor NP Hz/3 321 Anlg In Sqr Root 0 48 Motor OL Factor 1.00 322 Analog In 1 Hi 10.0 Volt 53 Torque Perf Mode Sensrls Vect 323 Analog In 1 Lo 0.0 Volt 54 Maximum Voltage Drive Rated Volts 324 Analog In 1 Loss Disabled 55 Maximum Freq 110.0 or 130.0 Hz 325 Analog In 2 Hi 10.0 Volt 56 Compensation xxxxxxxxxxxxxx11 326 Analog In 2 Lo 0.0 Volt 57 Flux Up Mode Manual 327 Analog In 2 Loss Disabled 58 Flux Up Time 0.00 secs 341 Anlg Out Absolut xxxxxxxxxxxxxxx1 61 Autotune Calculate 342 Analog Out1 Sel Output Freq 62 IR Voltage Drop Based on Drive Rating 343 Analog Out1 Hi 10.00 Volt 63 Flux Current Ref Based on Drive Rating 344 Analog Out1 Lo 0.00 Volt 69 Start/Acc Boost Based on Drive Rating 361 Digital In1 Sel Stop - CF 70 Run Boost Based on Drive Rating 362 Digital In2 Sel Start 71 Break Voltage [Motor NP Volts] x 0.25 363 Digital In3 Sel Auto/Manual 72 Break Frequency [Motor NP Freq] x 0.25 364 Digital In4 Sel Speed Sel 1 80 Speed Mode Open Loop 365 Digital In5 Sel Speed Sel 2 81 Minimum Speed 0.0 Hz
366 Digital In6 Sel Speed Set 3 82 Maximum Speed 380 Digital Out1 Sel Fault 83 Overspeed Limit 10.0 Hz 381 Dig Out1 Level 0.0 84 Skip Frequency 1 0.0 Hz 382 Dig Out1 OnTime 0.00 Secs 85 Skip Frequency 2 0.0 Hz 383 Dig Out1 OffTime 0.00 Secs 86 Skip Frequency 3 0.0 Hz 384 Digital Out2 Sel Run 87 Skip Freq Band 0.0 Hz 385 Dig Out2 Level 0.0 90 Speed Ref A Sel Analog In 2 386 Dig Out2 OnTime 0.00 Secs 91 Speed Ref A Hi [Maximum Speed] 387 Dig Out2 OffTime 0.00 Secs 92 Speed Ref A Lo 0.0 Hz
93 Speed Ref B Sel Preset Spd1
94 Speed Ref B Hi [Maximum Speed]
95 Speed Ref B Lo 0.0 Hz
96 TB Man Ref Sel Analog In 1
97 TB Man Ref Hi [Maximum Speed]
98 TB Man Ref Lo 0.0 Hz 100 Jog Speed 10.0 Hz
50.0 or 60.0 Hz
(Dep. on voltage class)
Par Parameter Name Factory Default Programmed Value Par Parameter Name Factory Default Programmed Value
101 Preset Speed 1 5.0 Hz 195 MOP Rate 1.0 Hz/s 102 Preset Speed 2 10.0 Hz 196 Param Access Lvl Basic 103 Preset Speed 3 20.0 Hz 197 Reset To Defalts Ready 104 Preset Speed 4 30.0 Hz 198 Load Frm Usr Set Ready 105 Preset Speed 5 40.0 Hz 199 Save To User Set Ready 106 Preset Speed 6 50.0 Hz 200 Reset Meters Ready 107 Preset Speed 7 60.0 Hz 201 Language Not Selected 117 Trim In Select Analog In 2 202 Voltage Class Based on Drive Cat. No. 118 Trim Out Select xxxxxxxxxxxxxx00 203 Drive Checksum Read Only 119 Trim Hi 60.0 Hz 209 Drive Status 1 Read Only 120 Trim Lo 0.0 Hz 210 Drive Status 2 Read Only
121 Slip RPM @ FLA 122 Slip Comp Gain 40.0 212 Drive Alarm 2 Read Only 123 Slip RPM Meter Read Only 213 Speed Ref Source Read Only 124 PI Configuration xxxxxxxxxx000000 214 Start Inhibits Read Only 125 PI Control xxxxxxxxxxxxx000 215 Last Stop Source Read Only 126 PI Reference Sel PI Setpoint 216 Dig In Status Read Only 127 PI Setpoint 50.00% 217 Dig Out Status Read Only 128 PI Feedback Sel Analog In 2 218 Drive Temp Read Only 129 PI Integral Time 2.00 Secs 219 Drive OL Count Read Only 130 PI Prop Gain 1.00 220 Motor OL Count Read Only 131 PI Lower Limit -[Maximum Freq] 224 Fault Frequency Read Only 132 PI Upper Limit +[Maximum Freq] 225 Fault Amps Read Only 133 PI Preload 0.0 Hz 226 Fault Bus Volts Read Only 134 PI Status Read Only 227 Status 1 @ Fault Read Only 135 PI Ref Meter Read Only 228 Status 2 @ Fault Read Only 136 PI Fdback Meter Read Only 229 Alarm 1 @ Fault Read Only 137 PI Error Meter Read Only 230 Alarm 2 @ Fault Read Only 138 PI Output Meter Read Only 234 Testpoint 1 Sel 499 140 Accel Time 1 10.0 Secs 235 Testpoint 1 Data Read Only 141 Accel Time 2 10.0 Secs 236 Testpoint 2 Sel 499 142 Decel Time 1 10.0 Secs 237 Testpoint 2 Data Read Only 143 Decel Time 2 10.0 Secs 238 Fault Config 1 xxxxxxxxx1001x10 146 S-Curve % 0% 240 Fault Clear Ready 147 Current Lmt Sel Cur Lim Val 241 Fault Clear Mode Enabled 148 Current Lmt Val [Rated Amps] x 1.5 242 Power Up Marker Read Only 149 Current Lmt Gain 250 243 Fault 1 Code Read Only 150 Drive OL Mode Both-PWM 1st 244 Fault 1 Time Read Only 151 PWM Frequency 4 kHz 245 Fault 2 Code Read Only 155 Stop Mode A Ramp 246 Fault 2 Time Read Only 156 Stop Mode B Coast 247 Fault 3 Code Read Only 157 DC Brk Lvl Sel DC Brake Lvl 248 Fault 3 Time Read Only 158 DC Brake Level [Rated Amps] 249 Fault 4 Code Read Only 159 DC Brake Time 0.0 sec 250 Fault 4 Time Read Only 160 Bus Reg Ki 450 259 Alarm Config 1 xxxxxx111x111111 161 Bus Reg Mode A Adjust Freq 270 DPI Baud Rate 125 kbps 162 Bus Reg Mode B Both-Frq 1st 271 Drive Logic Rslt Read Only 163 DB Resistor Type Internal Res 272 Drive Ref Rslt Read Only 168 Start At PowerUp Disabled 273 Drive Ramp Rslt Read Only 169 Flying Start En Disabled 276 Logic Mask xxxxxxxxxx1x1111 170 Flying StartGain 4000 277 Start Mask xxxxxxxxxx1x1111 174 Auto Rstrt Tries 0 278 Jog Mask xxxxxxxxxx1x1111 175 Auto Rstrt Delay 1.0 Secs 279 Direction Mask xxxxxxxxxx1x1111 184 Power Loss Mode Coast 280 Reference Mask xxxxxxxxxx1x1111 185 Power Loss Time 0.5 Secs 281 Accel Mask xxxxxxxxxx1x1111 190 Direction Mode Unipolar 282 Decel Mask xxxxxxxxxx1x1111 192 Save HIM Ref xxxxxxxxxxxxxxx1 283 Fault Clr Mask xxxxxxxxxx1x1111 193 Man Ref Preload Disabled 284 MOP Mask xxxxxxxxxx1x1111 194 Save MOP Ref xxxxxxxxxxxxxx00 285 Local Mask xxxxxxxxxx1x1111
Based on
[Motor NP RPM] 211 Drive Alarm 1 Read Only
PowerFlex 70
Parameter Record
PowerFlex 70 Parameter Record
Date programmed
Drive Serial #
Drive Rated Amps x 2
Read Only
Drive Rating x -2
Drive Rating x +2
Read Only
Drive Rating x -2
Drive Rating x +2
Read Only
Drive Rated Volts
Read Only
Elapsed MWh
0.0 MWh
429496729.5 MWh
Read Only
Elapsed Run Time
0.0 Hrs
429496729.5 Hrs
Read Only
Based on Drive Rating
Read Only
Based on Drive Rating
Based on Drive Rating
Read Only
16
Analog In1 Value
-10.000V
+10.000V
Read Only
17
Analog In2 Value
-10.000V
+10.000V
Read Only
0.0 VAC
[Rated Volts]
Based on Drive Rating
0.0 Amps
[Rated Amps] x 2
Based on Drive Rating
5.0 Hz
400.0 Hz
110.0 or 130.0 Hz
[Maximum Speed]
0.0 Hz
5.0 Hz
400.0 Hz
on voltage class)
87
Skip Freq Band
0.0 Hz
30.0 Hz
0.0 Hz
Machine #
Par Parameter Name Minimum Value Maximum Value Factory Default Programmed Value
1 Output Freq - [Maximum Freq] + [Maximum Freq] Read Only
2 Commanded Freq - [Maximum Speed] + [Maximum Speed] Read Only 3 Output Current 0.0 Amps 4 Torque Current 5 Flux Current 6 Output Voltage 0.0 VAC 7 Output Power 0.0 kW Drive Rated kW x 2 Read Only 8 Output Powr Fctr 0.00 1.00 Read Only
9 10 11 MOP Frequency - [Maximum Frequency] + [Maximum Frequency] Read Only 12 DC Bus Voltage Based on Drive Rating 13 DC Bus Memory
0.000 mA
20.000 mA
0.000 mA
20.000 mA
26 Rated kW 0.37 kW 15.0 kW Read Only 27 Rated Volts Based on Drive Rating Based on Drive Rating Read Only 28 Rated Amps 1.1 Amps 32.2 Amps Read Only 29 Control SW Ver 0.000 65.256 Read Only 40 Motor Type Induction Induction
Synchr Reluc
Synchr PM 41 Motor NP Volts 42 Motor NP FLA 43 Motor NP Hertz 5.0 Hz 400.0 Hz Based on Drive Cat. No. 44 Motor NP RPM 60 RPM 24000 RPM 1750 RPM 45 Motor NP Power 0.0 100.0 Based on Drive Rating 46 Mtr NP Pwr Units Horsepower Based on Drive Rating
kiloWatts 47 Motor OL Hertz 0.0 Hz Motor NP Hz Motor NP Hz/3 48 Motor OL Factor 0.20 2.00 1.00 53 Torque Perf Mode Sensrls Vect Sensris Vect
SV Economize
Custom V/Hz
Fan/Pmp V/Hz 54 Maximum Voltage Rated Volts x 0.25 Rated Volts x 1.0 Drive Rated Volts 55 Maximum Freq 56 Compensation Reflect Wave 1
Enable Jerk 1
57 Flux Up Mode Manual Manual
Automatic 58 Flux Up Time 0.00 secs 5.00 secs 0.00 secs 61 Autotune Ready Calculate
Static Tune
Rotate Tune
Calculate 62 IR Voltage Drop 0.0 VAC [Motor NP Volts] x 0.25 Based on Drive Rating 63 Flux Current Ref 0.00 Amps [Motor NP FLA] Based on Drive Rating 69 Start/Acc Boost 0.0 VAC [Motor NP Volts] x 0.25 Based on Drive Rating 70 Run Boost 0.0 VAC [Motor NP Volts] x 0.25 Based on Drive Rating 71 Break Voltage 0.0 VAC [Motor NP Volts] [Motor NP Volts] x 0.25 72 Break Frequency 0.0 Hz [Motor NP Freq] [Motor NP Freq] x 0.25 80 Speed Mode Open Loop Open Loop
Slip Comp
Process PI
81 Minimum Speed 0.0 Hz
50.0 or 60.0 Hz (Dependent 82 Maximum Speed 83 Overspeed Limit 0.0 Hz 20.0 Hz 10.0 Hz 84 Skip Frequency 1 - [Maximum Speed] + [Maximum Speed] 0.0 Hz 85 Skip Frequency 2 - [Maximum Speed] + [Maximum Speed] 0.0 Hz 86 Skip Frequency 3 - [Maximum Speed] + [Maximum Speed] 0.0 Hz
1 of 17
PowerFlex 70 Parameter Record
Date programmed
Drive Serial #
- [Maximum Speed]
+ [Maximum Speed]
[Maximum Speed]
- [Maximum Speed]
+ [Maximum Speed]
0.0 Hz
- [Maximum Speed]
+ [Maximum Speed]
[Maximum Speed]
95
Speed Ref B Lo
- [Maximum Speed]
+ [Maximum Speed]
0.0 Hz
Machine #
Par Parameter Name Minimum Value Maximum Value Factory Default Programmed Value
90 Speed Ref A Sel Analog In 1 Analog In 2
Analog In 2
Reserved Reserved Reserved Reserved Reserved Reserved Reserved
MOP Level
Reserved Preset Spd1 Preset Spd2 Preset Spd3 Preset Spd4 Preset Spd5 Preset Spd6 Preset Spd7
DPI Port 1 DPI Port 2 DPI Port 3
Reserved
DPI Port 5 91 Speed Ref A Hi 92 Speed Ref A Lo 93 Speed Ref B Sel Analog In 1 Preset Spd1
Analog In 2
Reserved Reserved Reserved Reserved Reserved Reserved
MOP Level
Reserved Preset Spd1 Preset Spd2 Preset Spd3 Preset Spd4 Preset Spd5 Preset Spd6 Preset Spd7
DPI Port 1 DPI Port 2 DPI Port 3
Reserved
DPI Port 5
94 Speed Ref B Hi
2 of 17
PowerFlex 70 Parameter Record
Date programmed
Drive Serial #
- [Maximum Speed]
+ [Maximum Speed]
[Maximum Speed]
- [Maximum Speed]
+ [Maximum Speed]
0.0 Hz
- [Maximum Speed]
+ [Maximum Speed]
10.0 Hz
- [Maximum Speed]
+ [Maximum Speed]
5.0 Hz
- [Maximum Speed]
+ [Maximum Speed]
10.0 Hz
- [Maximum Speed]
+ [Maximum Speed]
20.0 Hz
- [Maximum Speed]
+ [Maximum Speed]
30.0 Hz
- [Maximum Speed]
+ [Maximum Speed]
40.0 Hz
- [Maximum Speed]
+ [Maximum Speed]
50.0 Hz
- [Maximum Speed]
+ [Maximum Speed]
60.0 Hz
- [Maximum Speed]
+ [Maximum Speed]
60.0 Hz
- [Maximum Speed]
+ [Maximum Speed]
0.0 Hz
Based on [Motor NP RPM]
PI Reset
0
Machine #
Par Parameter Name Minimum Value Maximum Value Factory Default Programmed Value
96 TB Man Ref Sel Analog In 1 Analog In 1
Analog In 2
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
MOP Level 97 TB Man Ref Hi 98 TB Man Ref Lo
100 Jog Speed 101 Preset Speed 1 102 Preset Speed 2 103 Preset Speed 3 104 Preset Speed 4 105 Preset Speed 5 106 Preset Speed 6 107 Preset Speed 7 117 Trim In Select Analog In 1 Analog In 2
Analog In 2
Reserved Reserved Reserved Reserved Reserved Reserved
MOP Level
Reserved Preset Spd1 Preset Spd2 Preset Spd3 Preset Spd4 Preset Spd5 Preset Spd6 Preset Spd7
DPI Port 1 DPI Port 2 DPI Port 3 DPI Port 4 DPI Port 5
118 Trim Out Select Trim Ref A 0
Trim Ref B 0 119 Trim Hi 120 Trim Lo 121 Slip RPM @ FLA 0.0 RPM 1200.0 RPM 122 Slip Comp Gain 1.0 100.0 40.0 123 Slip RPM Meter 0.0 RPM 300.0 RPM Read Only 124 PI Configuration Excl Mode 0
Invert Error 0
Preload Mode 0
Ramp Ref 0
Zero Clamp 0
Feedbak Sqrt 0
125 PI Control PI Enable 0
PI Hold 0
3 of 17
PowerFlex 70 Parameter Record
Date programmed
Drive Serial #
Value
+ 100% of Maximum Process Value
50.00%
-400.0 Hz
+400.0 Hz
-[Maximum Freq]
-400.0 Hz
+400.0 Hz
+[Maximum Freq]
133
PI Preload
-400.0 Hz
+400.0 Hz
0.0 Hz
Machine #
Par Parameter Name Minimum Value Maximum Value Factory Default Programmed Value
126 PI Reference Sel PI Setpoint PI Setpoint
Analog In 1 Analog In 2
Reserved Reserved Reserved Reserved Reserved Reserved
MOP Level
Master Ref Preset Spd1 Preset Spd2 Preset Spd3 Preset Spd4 Preset Spd5 Preset Spd6 Preset Spd7
DIP Port 1 DPI Port 2 DPI Port 3 DPI Port 4 DPI Port 5
-100.00% of Maximum Process 127 PI Setpoint 128 PI Feedback Sel PI Setpoint Analog In 2
Analog In 1 Analog In 2
Reserved Reserved Reserved Reserved Reserved Reserved
MOP Level
Master Ref Preset Spd1 Preset Spd2 Preset Spd3 Preset Spd4 Preset Spd5 Preset Spd6 Preset Spd7
DIP Port 1 DPI Port 2 DPI Port 3 DPI Port 4
DPI Port 5 129 PI Integral Time 0.00 Secs 100.00 Secs 2.00 Secs 130 PI Prop Gain 0.00 100.00 1.00 131 PI Lower Limit 132 PI Upper Limit
4 of 17
PowerFlex 70 Parameter Record
Date programmed
Drive Serial #
Based On Drive Rating
Based On Drive Rating
[Rated Amps] x 1.5
2 kHz
10 kHz
4 kHz
0.0 Amps
[Rated Amps] x 1.5
[Rated Amps]
High Voltage
Machine #
Par Parameter Name Minimum Value Maximum Value Factory Default Programmed Value
134 PI Status PI Enabled 0
PI Hold 0
PI Reset 0
PI InLimit 0 135 PI Ref Meter -100.00 % +100.00 % Read Only 136 PI Fdback Meter -100.00 % +100.00 % Read Only 137 PI Error Meter -100.00 % +100.00 % Read Only 138 PI Output Meter -[Maximum Freq] +[Maximum Freq] Read Only 140 Accel Time 1 0.1 Secs 3600.0 Secs 10.0 Secs 141 Accel Time 2 0.1 Secs 3600.0 Secs 10.0 Secs 142 Decel Time 1 0.1 Secs 3600.0 Secs 10.0 Secs 143 Decel Time 2 0.1 Secs 3600.0 Secs 10.0 Secs 146 S-Curve % 0% 100% 0% 147 Current Lmt Sel Cur Lim Val Cur Lim Val
Analog In 1
Analog In 2 148 Current Lmt Val 149 Current Lmt Gain 0 5000 250 150 Drive OL Mode Disabled Both-PWM 1st
Reduce CLim Reduce PWM
Both-PWM 1st 151 PWM Frequency 155 Stop Mode A Coast Ramp
Ramp
Ramp to Hold
DC Brake
156 Stop Mode B Coast Coast
Ramp
Ramp to Hold
DC Brake
157 DC Brk Lvl Sel DC Brake Lvl DC Brake Lvl
Analog In 1
Analog In 2 158 DC Brake Level 159 DC Brake Time 0.0 sec 90.0 sec 0.0 sec 160 Bus Reg Ki 0 5000 450 161 Bus Reg Mode A Disabled Adjust Freq
Adjust Freq
Dynamic Brak
Both-DB 1st Both-Frq 1st
162 Bus Reg Mode B Disabled Both-Frq 1st
Adjust Freq
Dynamic Brak
Both-DB 1st Both-Frq 1st
163 DB Resistor Type Internal Res Internal Res
External Res
None
168 Start At PowerUp Disabled Disabled
Enabled
169 Flying Start En Disabled Disabled
Enabled 170 Flying StartGain 20 32767 4000 174 Auto Rstrt Tries 0 9 0 175 Auto Rstrt Delay 0.5 Secs 30.0 Secs 1.0 Secs 184 Power Loss Mode Coast Coast
Decel 185 Power Loss Time 0.0 Secs 60.0 Secs 0.5 Secs 190 Direction Mode Unipolar Unipolar
Bipolar
Reverse Dis 192 Save HIM Ref At Powr Down 1 193 Man Ref Preload Disabled Disabled
Enabled
194 Save MOP Ref At Powr Down 0
At Stop 0 195 MOP Rate 0.2 Hz/s [Maximum Freq] 1.0 Hz/s 196 Param Access Lvl Basic Basic
Advanced
197 Reset To Defalts Ready Ready
Factory
Low Voltage
5 of 17
PowerFlex 70 Parameter Record
Date programmed
Drive Serial #
Based on Drive Cat. No.
Spd Ref ID 3
0
Machine #
Par Parameter Name Minimum Value Maximum Value Factory Default Programmed Value
198 Load Frm Usr Set Ready Ready
User Set 1 User Set 2 User Set 3
199 Save To User Set Ready Ready
User Set 1 User Set 2 User Set 3
200 Reset Meters Ready Ready
MWh
Elapsed Time
201 Language Not Selected Not Selected
English
Francais
Espanol
Italiano
Deutsch Reserved Portugues Reserved Reserved
Nederlands
202 Voltage Class Low Voltage
High Voltage 203 Drive Checksum 0 65535 Read Only 209 Drive Status 1 Ready 0
Active 0
Command Dir 1
Actual Dir 1 Accelerating 0 Decelerating 0
Alarm 0
Faulted 1
At Speed 0 Local ID 0 1 Local ID 1 1 Local ID 2 1
Spd Ref ID 0 0 Spd Ref ID 1 0 Spd Ref ID 2 0
6 of 17
PowerFlex 70 Parameter Record
Date programmed
Drive Serial #
DPI Port 5
Machine #
Par Parameter Name Minimum Value Maximum Value Factory Default Programmed Value
210 Drive Status 2 Ready 0
Active 0
Running 0
Jogging 0
Stopping 0
DC Braking 0
Auto Tuning 0
Unused X
AutoRst Ctdn 0
AutoRst Act 0
Curr Limit 0
Bus Freq Reg 0
Motor Overld 0 DPI at 500 k 0
Unused X Unused X
211 Drive Alarm 1 Prechrg Actv 0
UnderVoltage 0
Power Loss 0
Str At PwrUp 0
Anlg in Loss 0
IntDBRes OH 0
Unused X Drv OL Lvl 1 0 Drv OL Lvl 2 0
Decel Inhibt 0
Unused X
Unused X
Unused X
Unused X
Unused X
Unused X
212 Drive Alarm 2 DigIn CflctA 0
DigIn CflctB 0
DigIn CflctC 0
Bipolr Cflct 0
MtrTyp Cflct 0
NP Hz Cflct 0
MaxFrq Cflct 0
VHz NegSlope 0
IR Vlts Rang 0
FlxAmps Rang 0
SpdRef Cflct 0
213 Speed Ref Source PI Output Read Only
Analog In 1 Analog In 2
Reserved Reserved Reserved Reserved Reserved Reserved
MOP Level
Jog Speed Preset Spd1 Preset Spd2 Preset Spd3 Preset Spd4 Preset Spd5 Preset Spd6 Preset Spd7
DPI Port 1
DPI Port 2
DPI Port 3
Reserved
7 of 17
PowerFlex 70 Parameter Record
Date programmed
Drive Serial #
0.0
100.00%
Read Only
0.0
100.00%
Read Only
0.0
100.00%
Read Only
Spd Ref ID 3
0
Machine #
Par Parameter Name Minimum Value Maximum Value Factory Default Programmed Value
214 Start Inhibits Faulted 1
Type 2 Alarm 0
Enable 0
DC Bus Pchrg 0
Stop Assertd 1
Params Reset 0
Startup Actv 0
Unused X
Digital In 1 DPI Port 1 0 DPI Port 2 0 DPI Port 3 0
Unused X
DPI Port 5 0
Unused X Unused X
215 Last Stop Source Pwr Removed Read Only
DPI Port 1 DPI Port 2 DPI Port 3
Reserved
DPI Port 5
Reserved
Digital In
Fault
Not Enabled
Sleep
Jog
216 Dig In Status Digital In1 0
Digital In2 0 Digital In3 0 Digital In4 0 Digital In5 0 Digital In6 0
217 Dig Out Status Digital Out1 0
Digital Out2 0 218 Drive Temp 219 Drive OL Count 220 Motor OL Count 224 Fault Frequency 0.0 +[Maximum Freq] Read Only 225 Fault Amps 0.0 Amps [Rated Amps] x 2 Read Only 226 Fault Bus Volts 0.0 VDC Max Bus Volts Read Only 227 Status 1 @ Fault Ready 0
Active 0
Command Dir 1
Actual Dir 1 Accelerating 0 Decelerating 0
Alarm 0
Faulted 1
At Speed 0 Local ID 0 1 Local ID 1 1 Local ID 2 1
Spd Ref ID 0 0 Spd Ref ID 1 0 Spd Ref ID 2 0
8 of 17
Loading...
+ 30 hidden pages