PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2004
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
LISTENING MODE
SELECT
STANDBY/ON
ENTER
MULTI JOG
DVD/LD TV/SAT DVR/VCR VIDEO1
CD-R/
TUNER VIDEO2
CD
TAPE/MD
MASTER VOLUME
VSX-2014i
ORDER NO.
RRV3008
VSX-2014i-S
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
VSX-2014i-S
VSX-1014-S
VSX-1014-K
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
ModelTypePorew Requirement
VSX-2014i-SHYXJAC220-230VAC240V, *
VSX-1014-SHYXJAC220-230VAC240V, *
VSX-1014-KHYXJAC220-230VAC240V, *
*:Alter the wiring of the power-supply block at the primary winding of Power transformer referring to the Line Voltage Selection
described in Service Manual.
The voltage can be converted by the
following method.
For details, refer to "Important symbols for good services".
T-ZZR AUG. 2004 printed in Japan
1234
SAFTY INFORMATION
A
This service manual is intended for qualified service technicians; it is not meant for the casual
do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been
trained to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to
B
cause cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 – Proposition 65
NOTICE
(FOR CANADIAN MODEL ONLY)
Fuse symbols (fast operating fuse) and/or (slow operating fuse) on PCB indicate that replacement
parts must be of identical designation.
REMARQUE
(POUR MODÈLE CANADIEN SEULEMENT)
Les symboles de fusible (fusible de type rapide) et/ou (fusible de type lent) sur CCI indiquent que
C
les pièces de remplacement doivent avoir la même désignation.
(FOR USA MODEL ONLY)
1. SAFETY PRECAUTIONS
The following check should be performed for the
continued protection of the customer and service
technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground
(water pipe, conduit, etc.) by connecting a leakage
current tester such as Simpson Model 229-2 or
D
equivalent between the earth ground and all exposed
metal parts of the appliance (input/output terminals,
screwheads, metal overlays, control shaft, etc.). Plug
the AC line cord of the appliance directly into a 120V
AC 60 Hz outlet and turn the AC power switch on. Any
current measured must not exceed 0.5 mA.
Leakage
current
E
Device
under
test
Also test with
plug reversed
(Using AC adapter
plug as required)
Test all
exposed metal
surfaces
AC Leakage Test
tester
Reading should
not be above
0.5 mA
Earth
ground
ANY MEASUREMENTS NOT WITHIN THE
LIMITS OUTLINED ABOVE ARE INDICATIVE
OF A POTENTIAL SHOCK HAZARD AND
MUST BE CORRECTED BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance
have special safety related characteristics. These are
often not evident from visual inspection nor the
protection afforded by them necessarily can be obtained
by using replacement components rated for voltage,
wattage, etc. Replacement parts which have these
special safety characteristics are identified in this
Service Manual.
Electrical components having such features are
identified by marking with a
on the parts list in this Service Manual.
The use of a substitute replacement component which
does not have the same safety characteristics as the
PIONEER recommended replacement one, shown in the
parts list in this Service Manual, may create shock, fire,
or other hazards.
Product Safety is continuously under review and new
instructions are issued from time to time. For the latest
information, always consult the current PIONEER
Service Manual. A subscription to, or additional copies
of, PIONEER Service Manual may be obtained at a
nominal charge from PIONEER.
on the schematics and
F
2
1234
VSX-2014i-S
5678
[ Important symbols for good services ]
In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely.
When you find the procedures bearing any of the symbols, be sure to fulfill them:
1. Product safety
You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and
should keep the safety during servicing by following the safety instructions described in this manual.
2. Adjustments
To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable.
In accordance with the procedures or instructions described in this manual, adjustments should be performed.
3. Cleaning
For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning,
proper cleaning should be performed to restore their performances.
4. Shipping mode and shipping screws
To protect the product from damages or failures that may be caused during transit, the shipping mode should be set or
the shipping screws should be installed before shipping out in accordance with this manual, if necessary.
A
B
5. Lubricants, glues, and replacement parts
Appropriately applying grease or glue can maintain the product performances. But improper lubrication or applying
glue may lead to failures or troubles in the product. By following the instructions in this manual, be sure to apply the
prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed
ones should be used.
CONTENTS
SAFTY INFORMATION ........................................................................................................................................2
4.3 COMPOSITE V ASSY.............................................................................................................................. 69
4.4 S VIDEO ASSY........................................................................................................................................ 70
4.5 VIDEO SIDE and OPTICAL-IN ASSYS ................................................................................................... 71
5. PCB PARTS LIST ......................................................................................................................................... 108
7.2.1 IC ..................................................................................................................................................... 144
8.1 FRONT PANEL ...................................................................................................................................... 165
• Specifications and the design are subject to possible
modifications without notice, due to improvements.
Cleaning the unit
• Use a polishing cloth or dry cloth to wipe off dust and
dirt.
• When the surface is dirty, wipe with a soft cloth
dipped in some neutral cleanser diluted five or six
times with water, and wrung out well, and then wipe
again with a dry cloth. Do not use furniture wax or
cleansers.
• Never use thinners, benzine, insecticide sprays or
other chemicals on or near this unit, since these will
corrode the surface.
D
E
F
56
VSX-2014i-S
5
7
8
1234
2. EXPLODED VIEWS AND PARTS LIST
NOTES:
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
The mark found on some component parts indicates the importance of the safety factor of the part.
A
Therefore, when replacing, be sure to use parts of identical designation.
Screws adjacent to mark on product are used for disassembly.
For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions, apply as you think it appropriate.)
2.1 PACKING
B
19
20
21
C
2
3
8
9
4
5
6
1
10
7
17
18
8
12
14
Accessories
D
AM Loop Antenna
(ATB7013)
E
F
11
VSX-2014i-S
Only
INPUT
RECEIVER
DTV MENU
SELECT
DVD/LD TV/SAT DVR/VCR TV CONT
MULTI CONTROL
CD-R/TAPE
TUNER RECEIVER
CD
INPUT ATT FL DIMMER SR
+
10
D.ACCESS
TOP MENU
TUNE
STST
ENTER
T.EDIT
TUNE
SYSTEM
SETUP
GUIDE
TV CONTROL
INPUT
TV CH
TV VOL
SELECT
DTV ON/OFF
DTV INFORECMUTE
TUNER
REC STOP
DISPLAY
MPX
CH RETURN
HDD
AUDIO
SUBTITLE
CH CH
RECEIVER CONTROL
THX
STANDARD ADV.SURR STEREO
SIGNAL
ACOUSTIC
SELECT
EQ
AUTO SURR
EFFECT
SLEEP DIALOG E
SHIFT
/CH SEL
RECEIVER
MIDNIGHT/
LOUDNESS
SOURCE
ENTER
DISC
CLASS
MENU
BAND
RETURN
VOL
DVD
Remote Control Unit
( AXD7383 )
13
AC Power Cord
(VSX-2014i-S :
ADG7062)Only
FM Wire Antenna
(ADH7030)
Microphone Stand for Auto
Surround Sound Setup
(AEB7269)
16
"AA" IEC LR6 batteries
Microphone for Auto
Surround Sound Setup
(APM7004)
15
AUDIO/VIDEO MULTI-CHANNEL
RECEIVER
VSX-2014i
VSX-1014
Operating Instructions
Operating Instructions
(VSX-2014i-S : ARB7311)
6
VSX-2014i-S
1234
>
5678
(1) PACKING parts List
No.DescriptionPart No.
No.DescriptionPart No.
Mark
1MicrophoneAPM7004
for Auto Surround Sound Setup
2Microphone StandAEB7269
for Auto Surround Sound Setup
3FM Wire AntennaADH7030
4AM Loop AntennaATB7013
5Caution Sheet SP,EARM7083
NSP 6Warranty Card ARY7065
7Operating Instructions (English) ARB7311
NSP 8Polyethlene Bag(230x340x0.03)Z21-038
9Remote Control UnitAXD7383
10 Battery CoverXZN3140
Mark
11 AC Power CordSee Contrast table (2)
NSP 12 "AA" IEC LR6 batteriesVEM1023
13 Front Pad V1AHA7428
14 Rear Pad V1AHA7429
15 Packing SheetRHC1023
16 Packing CaseSee Contrast table (2)
17 Operating Instructions (Spanish)ARC7536
18 Operating Instructions (German)ARC7537
19 Operating Instructions (French) ARC7547
20 Operating Instructions (Dutch) ARC7548
21 Operating Instructions (Italian) ARC7549
(2) CONTRAST TABLE
VSX-2014i-S/HYXJ, VSX-1014-K/HYXJ and VSX-1014-S/HYXJ are constructed the same except for the following:
A
B
MarkNo.Symbol and Description
>
11
AC Power Cord
16 Packing Case 2014iAHD8257Not usedNot used
16 Packing Case 1014Not usedAHD8259AHD8258
VSX-2014i-S
/HYXJ
ADG7062Not usedNot used
VSX-1014-K
/HYXJ
VSX-1014-S
/HYXJ
C
D
56
VSX-2014i-S
E
F
7
7
8
1234
2.2 EXTERIOR SECTION
A
B
NON-CONTACT
C
SIDE
CONTACT SIDE
11
11
8
11
10
10
1
10
11
6
2
3
11
11
5
11
11
6
11
10
11
5
10
D
11
11
E
9
11
Refer to
"2.6 FRONT PANEL SECTION".
F
11
11
11
11
11
11
4
12
7
4
12
11
Refer to
"2.3 CHASSIS SECTION".
8
1234
VSX-2014i-S
5678
(1) EXTERIOR SECTION parts List
No.DescriptionPart No.
No.DescriptionPart No.
Mark
1Bonnet Case V1See Contrast table (2)
2Left BeamANG7401
3Center BeamANG7482
4InsulatorPNW2766
5Spacer (4.5 x 10 x 20)AEB7355
6Spacer 45B (6 x 7 x 13)AEB7264
Mark
7Nyron RivetAEC7408
8Label (DD/DTS/THX)ARW7281
NSP 9GetterSee Contrast table (2)
10 ScrewSee Contrast table (2)
11 ScrewBBZ30P080FCC
12 Cushion 55See Contrast table (2)
(2) CONTRAST TABLE
VSX-2014i-S/HYXJ, VSX-1014-K/HYXJ and VSX-1014-S/HYXJ are constructed the same except for the following:
A
MarkNo.Symbol and Description
1 Bonnet Case V1AZN7981AZN7980AZN7981
NSP9 GetterAAX8028AAX8029AAX8029
10 ScrewBBZ40P080FNI BBZ40P080FZK BBZ40P080FNI
12 Cushion 55PNM1339 Not usedNot used
VSX-2014i-S
/HYXJ
VSX-1014-K
/HYXJ
VSX-1014-S
/HYXJ
B
C
D
56
VSX-2014i-S
E
F
9
7
8
1234
2.3 CHASSIS SECTION
32
A
NON-CONTACT
B
SIDE
Y
6
A
CONTACT SIDE
5
10
4
X
29
36
10
32
32
28
AE
11
I
18
31
32
H
17
31
C
32
31
A
32
32
AD
D
31
D
B
C
8
1
14
32
32
32
AA
32
35
AF
32
9
AB
I
3
Z
B
Refer to
"2.5 HEATSINK SECTION".
7
F
30
32
32
D
24
2
E
34
F
26
32
23
23
16
H
C
30
32
E
32
13
15
30
32
12
32
VSX-2014i-S
Only
32
32
E
32
32
(Accessory of Panel Base V1B)
F
10
1234
19
32
Screw Cover
32
32
32
21
27
20
32
Refer to
"2.4 REAR PANEL SECTION".
22
25
25
27
32
VSX-2014i-S
Only
VSX-2014i-S
>
>
>
>
>
5678
(1) CHASSIS SECTION parts List
No.DescriptionPart No.
Mark
1PRIMARY AssyAWX8386
2SP/PS AssyAWX8375
3DIODE AssyAWX8376
4TRANS 2-1 AssyAWX8370
5TRANS 2-2 AssyAWX8371
6TRANS 1 AssyAWX8383
7VH TR AssyAWX8411
8TRANS SIDE AssyAWX8417
9Fuse (FU1 : T5.0A)REK1029
10 Fuse (FU4, 5 : T2.0A)REK1025
11 Power Transformer (T1501)ATS7375
12 AC Power CableSee Contrast table (2)
13 Flexible Cable (12P)ADD7477
14 Primary Angle 56ANG7526
15 DSP Shield A V1ANG7479
16 Cord StopperSee Contrast table (2)
17 Under Beam V1AND7478
18 Trans. Frame 45ANG7399
NSP 19 Panel Stay V1AND7066
No.DescriptionPart No.
Mark
20 Stabilizer 45See Contrast table (2)
21 Screw Cover 45AAEC7414
NSP 22 Under BaseSee Contrast table (2)
23 PCB MoldAMR2534
24 Locking Card SpacerPNW2917
25 Card SpacerDNK2769
26 Wire Saddle 5SAEC7500
27 Push RivetAEC7370
NSP 28 Binder (BK-1)ZCA-BK1
NSP 29 Trans. Label V1AAX8052
30 ScrewIBZ30P150FCC
31 Screw (4x12)ABA7109
32 ScrewBBZ30P080FCC
33 • • • •
34 AC Inlet AssySee Contrast table (2)
NSP 35 Fuse CardAAX7098
NSP 36 Fuse CardAAX2357
A
B
(2) CONTRAST TABLE
VSX-2014i-S/HYXJ, VSX-1014-K/HYXJ and VSX-1014-S/HYXJ are constructed the same except for the following:
MarkNo.Symbol and Description
>
NSP22 Under Base 52ANA7166Not used
NSP22 Under Base 1014Not usedANA7161
>
12 AC Power Cable Not usedVDG1080 VDG1080
16 Cord StopperNot usedCM-22BCM-22B
Stabilizer 45
20
34 AC Inlet Assy ADX7411Not used Not used
VSX-2014i-S
/HYXJ
ANG7408Not usedNot used
VSX-1014-K
/HYXJ
VSX-1014-S
/HYXJ
Not used
ANA7161
C
D
E
56
VSX-2014i-S
F
11
7
8
1234
2.4 REAR PANEL SECTION
A
VSX-2014i-S Only
23
23
25
24
NON-CONTACT
B
CONTACT SIDE
SIDE
VSX-2014i-S Only
AC Inlet Assy
1
15
13
19
16
2
23
23
23
23
23
23
21
23
23
23
23
K
F
22
VSX-2014i-S
D
3
C
C
4
E
8
Only
5
17
A
23
23
To
POWER AMP IN
6
G
7
18
AC
B
9
D
POWER PROTECT
E
from
10
from
TRANS SIDE
To
TRANS 2-1
28
14
L
VSX-2014i-S Only
26
M
W
11
AG
12
27
20
F
12
1234
VSX-2014i-S
5678
(1) REAR PANEL SECTION parts List
No.DescriptionPart No.
Mark
112V TRIGGER AssySee Contrast table (2)
2COMPONENT AssySee Contrast table (2)
3S VIDEO AssySee Contrast table (2)
4COMPOSITE V AssySee Contrast table (2)
5MULTI CH I/O AssySee Contrast table (2)
>
No.DescriptionPart No.
Mark
16 Flexible Cable (11P)ADD7476
17 Flexible Cable (17P)ADD7478
18 Flexible Cable (10P)ADD7472
19 Rear PanelSee Contrast table (2)
20 Card SpacerAEC7502
A
6REAR TOP AssyAWX8399
7OPTICAL-IN AssyAWX8394
8VIDEO SIDE AssyAWX8366
9AUDIO CONNECT AssyAWX8382
10 MAIN CONTROL AssySee Contrast table (2)
11 REGULATOR AssySee Contrast table (2)
12 DSP AssyAWX8414
13 FM/AM TUNER UnitAXX7170
14 Fuse (FU2501, 2502 : T1.25A) REK1023
15 Connector Assy (8P)See Contrast table (2)
21 Speaker Sheet V1AAK8176
22 Hexagonal ScrewSee Contrast table (2)
23 ScrewBBZ30P080FCC
24 ScrewBBT30P100FCC
25 Cushion Circle 14BAED7081
26 1394 AssyAWK7834
27 Flexible Cable (22P)ADD7471
28 Fuse CardAAX2348
(2) CONTRAST TABLE
VSX-2014i-S/HYXJ, VSX-1014-K/HYXJ and VSX-1014-S/HYXJ are constructed the same except for the following:
MarkNo.Symbol and Description
1 12V TRIGGER Assy
2 COMPONENT AssyAWX8359AWX8360AWX8360
3S VIDEO AssyAWX8356AWX8357AWX8357
4 COMPOSITE V AssyAWX8354AWX8355AWX8355
5 MULTI CH I/O AssyAWX8410AWX8352
10 MAIN CONTROL AssyAWX8345AWX8350AWX8350
11 REGULATOR AssyAWX8365AWX8369AWX8369
15 Connector Assy (8P)ADE7085Not used
19 Rear Panel 2014SYANC8255 Not used
19 Rear Panel 1014BY, SY Not usedANC8257ANC8256
22 Hexagonal ScrewABA7078Not used
26 1394 AssyAWK7834Not used
27 Flexible Cable (22P)ADD7471Not used
VSX-2014i-S
/HYXJ
AWX8395
VSX-1014-K
/HYXJ
Not used
VSX-1014-S
/HYXJ
Not used
AWX8352
Not used
Not used
Not used
Not used
Not used
B
C
D
56
VSX-2014i-S
E
F
13
7
8
1234
2.5 HEAT SINK SECTION
A
NON-CONTACT
B
15
C
D
SIDE
9
from
TRANS SIDE
CONTACT SIDE
15
11
11
15
12
14
15
11
12
A
11
from
AUDIO CONNECT
11
1
15
15
15
12
S
A
16
B
12
15
15
10
15
T
16
15
C
15
AH
5
13
15
B
15
V
U
17
13
6
from
SP/PS
15
15
15
15
10
C
D
2
12
15
15
12
11
11
D
11
3
To
TRANS 2-1
15
8
11
14
Q
15
4
R
19
18
19
E
F
14
1234
7
from
MAIN CONTROL
VSX-2014i-S
12
11
9
15
5678
HEAT SINK SECTION parts List
No.DescriptionPart No.
Mark
1POWER AMP-L AssyAWX8403
2POWER AMP-R AssyAWX8404
3POWER AMP IN AssyAWX8405
4POWER PROTECT AssyAWX8407
5POSI 1 L AssyAWX8536
6POSI 1 R AssyAWX8539
7Flexible Cable (15P)ADD7473
8Flexible Cable (18P)ADD7479
NSP 9Heat Sink 45ANH7152
10 H.S Angle V1ANG7481
A
11 PCB Angle 45ANG7406
12 Mica Sheet 45AEE7047
NSP 13 Speed ClampAEC7445
14 Nyron RivetAEC7408
15 ScrewBBZ30P100FCC
16 Screw (3x19)ABA7085
17 POSI 2 L AssyAWX8428
18 DC Fan MotorAXM7029
19 ScrewBBZ30P300FTC
B
C
D
56
VSX-2014i-S
E
F
15
7
8
1234
2.6 FRONT PANEL SECTION
A
NON-CONTACT
B
C
SIDE
CONTACT SIDE
26
25
23
12
13
28
22
22
30
22
27
9
A
28
31
29
16
24
19
17
(2/2)
(Magnet Holder)
18
28
H
A
27
4
P
1
28
20
22
5
28
Q
2
28
28
21
6
28
J
I
8
7
27
from
MAIN CONTROL
28
N
3
D
10
14
28
11
E
F
28
28
12
15
16
13
29
31
(1/2)
17
Screw Cover
(See section "2.3 CHASSIS SECTION".)
No. 17
(2/2)
Magnet Holder
16
VSX-2014i-S
1234
5678
(1) FRONT PANEL SECTION parts List
No.DescriptionPart No.
Mark
1MULTI JOG AssyAWX8479
2DISPLAY AssySee Contrast table (2)
3VOLUME AssyAWX8378
4HEADPHONE AssyAWX8380
5FRONT-IN AssyAWX8381
6FRONT-IN CONNECT AssyAWX8416
7Flexible Cable (15P)ADD7473
8Flexible Cable (26P)ADD7474
NSP 9Earth Lead WireADH7022
10 Pioneer Badge See Contrast table (2)
11 F. PanelSee Contrast table (2)
12 Rotary Knob See Contrast table (2)
13 RingABH7213
14 D. SheetSee Contrast table (2)
15 WindowSee Contrast table (2)
16 Cushion Circle 6See Contrast table (2)
17 Panel Base V1See Contrast table (2)
No.DescriptionPart No.
Mark
18 Magnet 35AMF7007
19 Standby Button V1See Contrast table (2)
20 Earth Plate AANG7484
NSP 21 Earth Spring 35ABH7193
22 Cushion 11 x 11AED7088
23 DoorSee Contrast table (2)
24 Door Base V1See Contrast table (2)
25 Door Shaft 35AMR7295
26 Damper Assy (240)AXA7136
27 ScrewABA7110
28 ScrewBPZ30P100FTC
29 Knob Spacer V1AEC7519
30 • • • •
31 NutNK90FCC
A
B
(2) CONTRAST TABLE
VSX-2014i-S/HYXJ, VSX-1014-K/HYXJ and VSX-1014-S/HYXJ are constructed the same except for the following:
MarkNo.Symbol and Description
2 DISPLAY AssyAWX8388AWX8389AWX8389
10 Pioneer Badge
11 F. Panel 2014SYANB7340Not usedNot used
11 F. Panel 1014BY, SYNot usedANB7342ANB7341
12 Rotary KnobAAA7025AAA7024AAA7025
14 D. Sheet 2014SYAAK8181Not usedNot used
14 D. Sheet 1014BY, SYNot usedAAK8183AAK8182
15 Window 2014AAK8187Not usedNot used
15 Window 1014Not usedAAK8186AAK8186
16 Cushion Circle 6AED7080AED7083AED7080
17 Panel Base V1AMB7871AMB7870AMB7871
19 Standby Button V1XAD3191XAD3173XAD3191
23 Door V1SANB7336Not usedANB7336
23 Door V1BNot usedANB7335Not used
24 Door Base V1AMR7478AMR7477AMR7478
COMPOSITE V ASSY
(VSX-2014i : AWX8354)
(VSX-1014 : AWX8355)
S VIDEO ASSY
(VSX-2014i : AWX8356)
(VSX-1014 : AWX8357)
C
(AWX8404)
S VIDEO ASSY
D
L
MAIN CONTROL ASSY
(VSX-2014i : AWX8345)
(VSX-1014 : AWX8350)
A
MULTI CH I/O ASSY
(VSX-2014i : AWX8410)
(VSX-1014 : AWX8352)
REAR TOP ASSY
AC
(AWX8399)
F
26
G
OPTICAL-IN ASSY
(AWX8394)
VSX-2014i-S
1234
FM/AM TUNER
UNIT Module
(AXX7170)
5678
÷
When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or
"PCB PARTS LIST".
÷
The > mark found on some component parts indicates the importance of the safety factor
of the part. Therefore, when replacing, be sure to use parts of identical designation.