Sarix® IBP Series Environmental Bullet Camera with IR
User Manual
C3958M-B-EN (5/15)
2
Contents |
|
Important Notices ......................................................................................................................................................................... |
5 |
Regulatory Notices .............................................................................................................................................................. |
5 |
Radio and Television Interference ....................................................................................................................................... |
5 |
Legal Notice......................................................................................................................................................................... |
5 |
Video Quality Caution .......................................................................................................................................................... |
5 |
Frame Rate Notice Regarding User Selected Options ........................................................................................................ |
5 |
Open Source Software ........................................................................................................................................................ |
6 |
KCC Certification ................................................................................................................................................................. |
6 |
Korean Class A EMC .................................................................................................................................................. |
6 |
ESD Warning ....................................................................................................................................................................... |
6 |
Network Topology Statement ....................................................................................................................................................... |
6 |
Legal Notice (Audio Notice).......................................................................................................................................................... |
6 |
Preface......................................................................................................................................................................................... |
7 |
1. Product Overview.............................................................................................................................................................. |
8 |
1.1 Dimensions .................................................................................................................................................................... |
8 |
1.2 Physical Characteristics................................................................................................................................................. |
9 |
2. Installation and Connection ........................................................................................................................................ |
11 |
2.1 Unpacking Everything .................................................................................................................................................. |
11 |
2.2 Optional Accessories ................................................................................................................................................... |
11 |
2.3 Installation.................................................................................................................................................................... |
11 |
2.3.1 Checking Appearance ...................................................................................................................................... |
11 |
2.3.2 Connecting the Wires ....................................................................................................................................... |
11 |
2.3.3 Installing the Camera........................................................................................................................................ |
12 |
2.3.4 Positioning the Camera .................................................................................................................................... |
14 |
2.3.5 Adjusting the Focus .......................................................................................................................................... |
15 |
2.3.6 Network Topology ............................................................................................................................................ |
15 |
2.3.7 System Requirements ...................................................................................................................................... |
16 |
3
2.4 Connection................................................................................................................................................................... |
17 |
2.4.1 Default IP Address ........................................................................................................................................... |
17 |
2.4.2 Connecting from a Computer & Viewing Preparation ....................................................................................... |
17 |
3. Administration and Configuration.............................................................................................................................. |
19 |
3.1 Live .............................................................................................................................................................................. |
19 |
3.1.1 Zoom and Focus Controls ................................................................................................................................ |
20 |
3.2 Settings........................................................................................................................................................................ |
20 |
3.2.1 System ............................................................................................................................................................. |
20 |
3.2.2 Network ............................................................................................................................................................ |
24 |
3.2.3 Imaging............................................................................................................................................................. |
34 |
3.2.4 A/V Streams ..................................................................................................................................................... |
39 |
3.2.5 Users ................................................................................................................................................................ |
44 |
3.2.6 Events .............................................................................................................................................................. |
48 |
Specifications ....................................................................................................................................................................... |
58 |
Pelco Troubleshooting Contact Information ............................................................................................................................... |
62 |
4
Important Notices
REGULATORY NOTICES
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RADIO AND TELEVISION INTERFERENCE
This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission’s rules.
In order to maintain compliance with FCC regulations shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and television reception.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
LEGAL NOTICE
SOME PELCO EQUIPMENT CONTAINS, AND THE SOFTWARE ENABLES, AUDIO/VISUAL AND RECORDING CAPABILITIES, THE IMPROPER USE OF WHICH MAY SUBJECT YOU TO CIVIL AND CRIMINAL PENALTIES. APPLICABLE LAWS REGARDING THE USE OF SUCH CAPABILITIES VARY BETWEEN JURISDICTIONS AND MAY REQUIRE, AMONG OTHER THINGS, EXPRESS WRITTEN CONSENT FROM RECORDED SUBJECTS. YOU ARE SOLELY RESPONSIBLE FOR INSURING STRICT COMPLIANCE WITH SUCH LAWS AND FOR STRICT ADHERENCE TO ANY/ALL RIGHTS OF PRIVACY AND PERSONALTY. USE OF THIS EQUIPMENT AND/OR SOFTWARE FOR ILLEGAL SURVEILLANCE OR MONITORING SHALL BE DEEMED UNAUTHORIZED USE IN VIOLATION OF THE END USER SOFTWARE AGREEMENT AND RESULT IN THE IMMEDIATE TERMINATION OF YOUR LICENSE RIGHTS THEREUNDER.
VIDEO QUALITY CAUTION
FRAME RATE NOTICE REGARDING USER SELECTED OPTIONS
Pelco systems are capable of providing high quality video for both live viewing and playback. However, the systems can be used in lower quality modes, which can degrade picture quality, to allow for a slower rate of data transfer and to reduce the amount of video data stored. The picture quality can be degraded by either lowering the resolution, reducing the picture rate, or both. A picture degraded by having a reduced resolution may result in an image that is less clear or even indiscernible. A picture degraded by reducing the picture rate has fewer frames per second, which can result in images that appear to jump or move more quickly than normal during playback. Lower frame rates may result in a key event not being recorded by the system.
Judgment as to the suitability of the products for users' purposes is solely the users' responsibility. Users shall determine the suitability of the products for their own intended application, picture rate and picture quality. In the event users intend to use the video for evidentiary purposes in a judicial proceeding or otherwise, users should consult with their attorney regarding any particular requirements for such use.
5
OPEN SOURCE SOFTWARE
This product includes certain open source or other software originated from third parties that is subject to the GNU General Public License (GPL), GNU Library/Lesser General Public License (LGPL) and different and/or additional copyright licenses, disclaimers, and notices.
The exact terms of GPL, LGPL, and some other licenses are provided to you with this product. Please refer to the exact terms of the GPL and LGPL at http://www.fsf.org (Free Software Foundation) or http://www.opensource.org (Open Source Initiative) regarding your rights under said license. You may obtain a complete corresponding machine-readable copy of the source code of such software under the GPL or LGPL by sending your request to digitalsupport@pelco.com; the subject line should read Source Code Request. You will then receive an email with a link for you to download the source code.
This offer is valid for a period of three (3) years from the date of the distribution of this product by Pelco.
KCC CERTIFICATION
Korean Class A EMC
ESD WARNING
WARNING: This product is sensitive to Electrostatic Discharge (ESD). To avoid ESD damage to this product, use ESD safe practices during installation. Before touching, adjusting or handling this product, correctly attach an ESD wrist strap to your wrist and appropriately discharge your body and tools. For more information about ESD control and safe handling practices of electronics, please refer to ANSI/ESD S20.20-1999 or contact the Electrostatic Discharge Association (www.esda.org).
Network Topology Statement
IMPORTANT NOTE. PLEASE READ. The network implementation is shown as a general representation only and is not intended to show a detailed network topology. Your actual network will differ, requiring changes or perhaps additional network equipment to accommodate the system as illustrated. Please contact your local Pelco Representative to discuss your specific requirements.
Legal Notice (Audio Notice)
NOTE: Improper use of audio/visual recording equipment may subject you to civil and criminal penalties. Applicable laws regarding the use of such capabilities vary between jurisdictions and may require, among other things, express written consent from the recorded subjects. You are solely responsible for insuring strict compliance with such laws and for strict adherence to any/all right of privacy and personality.
WARRANTY STATEMENT
For information about Pelco's product warranty and thereto related information, refer to www.pelco.com/warranty.
6
Preface
This user manual is to be used as a reference for the installation and manipulation of the camera unit including features, functions, and a detailed explanation of the menu tree.
This manual provides the reader with the following information:
Product Overview: the main functions and system requirements of the unit
Installation and Connection: instructions on unit installation and wire connections
Administration and Configuration: the main menu navigation and controls explanations
7
1. Product Overview
1.1 Dimensions
The Sarix Series network IR bullet camera has two installation methods (refer to 2.3.3 Installing the Camera on page 12). Figure 1-1 depicts the dimensions of the environmental bullet with IR, as well as the dimensions of two back box configurations (ceiling mount, surface mount).
VALUES IN PARENTHESES ARE INCHES; ALL OTHERS ARE CENTIMETERS.
10.65(4.19) |
11.51(4.53) |
15.54(6.11)
9(3.54)
26.96(10.61)
ENVIRONMENTAL IR BULLET
15.52(6.11)
32.76(12.89)
ENVIRONMENTAL IR BULLET IN SURFACE MOUNT
37.06(14.59)
15(5.9)
ENVIRONMENTAL IR BULLET IN IN-CEILING MOUNT
FIGURE 1-1: PHYSICAL DIMENSIONS
8
1.2 Physical Characteristics
FIGURE 1-2: CAMERA CONNECTIONS AND FEATURES 1/2
1.Camera Main Body
2.Sun Shield: Minimize the effects of rain and sunlight on image quality.
3.RJ-45 Network Port: Connects the camera to the IP network. Also supplies power to the camera through the network using PoE. If PoE is not available, the camera is prewired for 24 VAC.
4.Power Connector (Black / Red): Connects to the external power source: AC24V (refer to camera label).
5.Digital I/O Connectors
A.Alarm Out (Blue-Signal / Brown-COM): Using the “Signal” and “COM” ports, connect to an external device to be triggered through alarm output signals.
B.Alarm In (Red-Signal / Black-GND): Using the “Signal” and “GND” ports, connect to an external device that can trigger alarm input signals.
C.Audio In (Purple-Signal / Green-GND): Using the “Signal” and “GND“ ports, connect to an external device like a microphone that receives sound for camera.
D.NA (Yellow-Signal / Orange-GND): Do not use these ports.
6.Mount Bracket: Install the camera to the wall or ceiling.
7.Metal Cover: Loosen the two screws and remove the metal cover then appears the interior buttons and inlets as the figure shows below.
8.Tripod Mount Screw Hole: Reserved for Tripod installation.
9
FIGURE 1-3: CAMERA CONNECTIONS AND FEATURES 2/2
1.Micro SD Card Slot (Micro SD): Insert a micro SD card to the slot for recording and storage.
2.Reset Button (R): Using a small tool, such as a paper clip, hold down the reset button within 5 seconds and release to restart the camera.
3.Default (DEFAULT): Using a small tool, such as a paper clip, hold down the reset button longer than 5 seconds to reset the camera to factory defaults.
4.Ethernet/PoE: The port in the middle and has connected to a POE cable. The other side is RJ-45 Network Port. Connects the camera to the IP network and LED indicators on.
5.Action (ACT) & Link (LINK): LED indicators. The LED indicators show the status as below:
|
|
|
|
|
|
|
|
|
|
|
|
|
Color |
|
|
|
Status |
|
|
|
Indication |
|
|
Green |
|
|
On |
|
|
Network connection is established. |
|
||||
|
|
|
|
|
|
|
|
|
|||
|
|
Off |
|
|
No network connection. |
|
|||||
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
Blinking |
|
|
Networking is active |
|
||
|
|
|
|
|
|
|
|
||||
Orange |
|
|
On |
|
|
Collision occurs |
|
||||
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
Off |
|
|
Networking is inactive |
|
||
|
|
|
|
|
|
|
|
|
|
|
|
10
2. Installation and Connection
2.1 Unpacking Everything
Check all items in the product box against the order form and the packing slip. In addition to this manual, the items below are included in the product box:
One Environmental IR Bullet Camera
One resource CD
One printed quick installation guide
One mounting template
One mounting kit with screws and wall inserts
One 24V connector
One alarm connector
One T-20 pin Torx screw driver
Please contact your dealer if any items are missing.
2.2 Optional Accessories
IBPBBAP-ES: a Sarix Environmental Surface mount for Bullet
IBPBBAP-EI: a Sarix Environmental In-Ceiling Mount for Bullet
2.3 Installation
The following tools might help you complete the installation:
a drill
screwdrivers
wire cutters
2.3.1 Checking Appearance
Although the protective materials used for the packaging should be able to protect the unit from most accidents during transportation, check the unit and its accessories for any visible damage. Remove the protective film to check items in accordance with the list in 2.1 Unpacking Everything.
2.3.2 Connecting the Wires
This unit supports one of the following options as power supply.
24 VAC: Connect 24V (~) cables to terminals ~24 VAC
PoE: Connect the RJ-45 network connector to a PoE compatible network device that supplied power through the Ethernet cable.
(Optional) Insert audio cable and alarm cable to the unit, and connect the network cable to the RJ-45 network port of a switch.
Caution To avoid damage to the unit, never connect more than one type of power supply (PoE IEEE802.3 Ethernet Class 3 or AC 24V power plug) at the same time.
11
2.3.3 Installing the Camera
You can install the Sarix Series bullet camera using one of the following installation methods:
Surface Mount (refer to 2.3.3.1 Surface Installation).
In-Ceiling Mount (refer to 2.3.3.2 In-Ceiling Installation).
2.3.3.1 Surface Installation
Ceiling or Wall
1.Use the supplied Guide Pattern to drill six 5mm mounting holes.
2.Insert the supplied anchors into the holes.
FIGURE 2-1: MOUNTING THE BRACKET
3.Pass all the signal cables through the mounting bracket.
4.Connect the camera power/video cable and external power/video cable together. The mounting bracket also has a cable relief if the mounting surface cannot be penetrated.
12
FIGURE 2-2 CABLE CONNECTION
5.Tighten the screws and finish the installation.
With IBPBBAP-ES
Also, you can mount the camera to the wall with IBPBBAP-ES Sarix Environmental Surface Mount for Bullet.
1.Fix the IBPBBAP-ES back box (#1) to the desirable surface by drilling three holes and fastening it with screws.
2.Pass all the signal cables through the hole of rubber (#5), and then insert the rubber into the center hole of metal plate. NOTE: Please identify both sides of the rubber. The side of the rubber with the inclined angle must be towards the terminals of the cables and metal plate to avoid water leakage.
3.Install the adaptor plate(#2) in the back box and tighten the screws
4.Insert screws (#4) through the bracket’s screw holes and tighten screws into the corresponding hole (#3) of the adaptor metal.
5.Complete Surface Installation with IBPBBAP-ES.
|
|
|
|
|
|
FIGURE 2-3: SURFACE MOUNT WITH IBPBBAP-ES
13
2.3.3.2 In-Ceiling Installation
The In-Ceiling Installation involves mounting the camera into the ceiling with IBPBBAP-EI Sarix Environmental In-Ceiling Mount for Bullet.
1.Pouch a round hole for IBPBBAP-EI back box to fit in.
2.Pass all the signal cables through the hole of rubber (#5), and then insert the rubber into the center hole of metal plate. NOTE: Please identify both sides of the rubber. The side of the rubber with the inclined angle must be towards the terminals of the cables and metal plate to avoid water leakage.
3.Install the adaptor plate(#2) in the back box and tighten the screws
4.Insert screws (#4) through the bracket’s screw holes and tighten screws into the corresponding hole (#3) of the adaptor metal.
5.Complete In-Ceiling Installation with IBPBBAP-EI.
FIGURE 2-4: IN-CEILING INSTALLATION WITH IBPBBAP-EI
2.3.4 Positioning the Camera
1.Loosen the locking screws (left and right) first (just rotate slightly one circle or the screws will fall down).
2.Rotate the Retaining ring then you will be able to hold the camera and adjust its angle.
3.Fasten the screws and retaining ring to ensure the desired angle.
14
Locking screws
FIGURE 2-5: POSITIONING THE CAMERA 1/2
FIGURE 2-6: POSITIONING THE CAMERA 2/2
2.3.5 Adjusting the Focus
1. View the camera image using the browser (refer to 2.4 Connection on page 17).
2. Use the settings in the Web interface (refer to 3.2.3.3 Focus on page 36) to adjust the zoom and focus of the lens to the desired field of view.
3. Also the focus can be adjusted b moving the zoom slider and using the Focus options in the live webpage.
NOTE: Focus adjustment is done exclusively with Web UI.
2.3.6 Network Topology
The camera can deliver video images and audio in real time using the Internet and Intranet. It's equipped with Ethernet RJ-45 network interface.
FIGURE 2-7: NETWORK TOPOLOGY TYPE I
15
FIGURE 2-8: NETWORK TOPOLOGY TYPE II
2.3.7 System Requirements
The table below lists the minimum requirements to implement and operate a unit. Network and processor bandwidth limitations might cause the video stream to pause or appear pixilated when additional Web-interface users connect to the camera. Decrease the images per second (ips), resolution, compression, or bit rate settings of the Web interface video streams to compensate for network/processor limitations.
|
|
|
|
TABLE 2-1: SYSTEM REQUIREMENTS |
|
|
|
|
|
||
|
System Hardware |
|
|
||
|
CPU |
|
|
Intel® Pentium® 4 microprocessor, 2.4GHz or equivalent |
|
|
RAM |
|
|
1 GB or above |
|
|
Monitor |
|
|
Minimum of 1024 x 768 resolution, 16or 32-bit pixel color resolution |
|
|
|
|
|
||
|
System Software |
|
|
||
|
Operating System |
Microsoft® Windows® XP, Vista 32 and 64 bit, Win7 32 and 64 bit |
|||
|
Browser |
|
|
Internet Explorer® 9.0, Apple® Safari® 7.0.6, Mozilla® Firefox® 31.0, Google® Chrome™ |
|
|
|
|
|
37.0.2062.124 m and later |
|
|
Media Player |
|
Pelco Media Player or QuickTime® 7.6.5 for Windows XP, Windows Vista, and Windows 7; or |
||
|
|
|
|
QuickTime 7.6.4 for Mac OS X 10.4 (or later) |
|
|
Unit |
|
|
|
|
|
Power Supply |
|
AC 24V / PoE |
||
|
|
|
|
|
|
|
|
|
|
||
Note |
1. |
All the installation and operations should comply with your local electricity safety rules. |
|||
|
|
2. |
Pelco Media Player is recommended for control, smoothness, and reduced latency as compared to |
||
|
|
|
QuickTime. The PMP is downloadable from Pelco web site: www.pelco.com/mediaplayer. |
||
|
|
3. |
This product is not compatible with QuickTime version 7.6.4 for Windows XP or Windows Vista. If |
||
|
|
|
you have this version installed on your PC, you will need to upgrade to QuickTime version 7.6.5. |
||
|
|
4. |
Network and processor bandwidth limitations might cause the video stream to pause or appear |
||
|
|
|
pixelated when additional Web-interface users connect to the camera. Decrease the images per |
||
|
|
|
second (ips), resolution, compression, or bit rate settings of the Web interface video streams to |
||
|
|
|
compensate for network or processor limitations. |
||
|
|
|
|
|
|
16
2.4 Connection
2.4.1 Default IP Address
The unit’s default IP address is 192.168.0.20 and sub mask is 255.255.255.0. When setting default IP address of 192.168.0.20 the camera will check to see if that address is already in use and will bump the last octet of the address by 1 if it is. The bump last octet of IP Address by 1 will continue until an unused IP address is found.
However, if you have a DHCP server in your network, the unit would obtain an IP address automatically from the DHCP server so that you don’t need to change the camera’s IP address. The factory default is DHCP On and 192.168.0.20 assignment only occurs when camera is set for DHCP but a DHCP server does not respond to request for an IP address.
2.4.2 Connecting from a Computer & Viewing Preparation
2.4.2.1 Using Pelco Device Utility Software to Get Camera’s IP Address
Pelco Device Utility software is a utility program that helps users to manage and configure the camera. Use the utility to find the IP address since the default option is to obtain an IP address via DHCP and therefore the IP address will NOT be known. Steps to get the utility program running are listed below.
1.Finish installing the Device Utility to the computer according to the installation instructions.
2.Log in to the Device Utility by entering the camera’s User name and Password. In the window, enter the default user name: admin and password: admin, then click Enter DU2 button to log in.
3.In the Manage Devices page, you can click Refresh Device List or Add New Device to search for the devices.
4.From the Device List, you can get series information about camera, IP Address included.
For more information about using the Device Utility, click this green icon "
" on the upper-right corner of the Device Utility page.
2.4.2.2 Connecting from a Computer
1.Check whether if the networking available between the unit and the computer by executing ping the default IP address. Start a command prompt (Windows: from the Start Menu, select Program. Select Accessories and choose Command Prompt.), and type “Ping 192.168.0.20”. If the message “Reply from…” appears, it means the connection is available.
2.Start Internet Explorer and enter IP address: 192.168.0.20. A login window should pop up. In the window, enter the default user name: admin and password: admin to log in.
NOTE: If you do not know the camera’s IP address, you can locate it using the Pelco Device Utility software (refer to 2.4.2.1 Using Pelco Device Utility Software to Get Camera’s IP Address).
Further administration on the unit can be found in “3. Administration and Configuration".
17
FIGURE 2-15: LOGIN WINDOW
2.4.2.3 Viewing Preparation
Images of the unit can be viewed through Microsoft Internet Explorer 8 or later. Before viewing, follow these steps to enable the display.
1.Enable Cookies On the Privacy tab, move the settings slider to Low or Accept All Cookies.
2.Change Security in Internet options and click Custom Level to open the Security Settings – Internet Zone screen.
NOTE: If the camera operates inside of the intranet, click the Intranet icon. If the camera operates outside of the intranet, click the Internet icon.
3.Scroll down to the ActiveX controls and plug-ins radio buttons and set as follows:
Download signed ActiveX controls Prompt (recommended)
Download unsigned ActiveX controls Prompt
Automatic prompting for ActiveX controls Enable
Run ActiveX controls and plug-ins Enable
Script ActiveX controls marked safe for scripting* Enable
4.Press OK to save the settings.
5.Close all Microsoft Internet Explorer Windows and restart a new window. This will allow the new settings taking effect.
6.Type your setting IP address into the browser.
7.Then you should be able to see the camera image screen.
18
3. Administration and Configuration
3.1 Live
Simply click on Live on the top right side of the browser window while accessing the IP address of the unit, and a live video is displayed directly in the browser window. When clicked on Settings, a window will pop up for configuring “System”, “Network”, “Imaging”, “A/V Streams”, “Users”, and “Events”. Please refer to 3.2 Settings on page 20 for more information. The current logged in identity shows to the right of the Help. Click on Logout admin of the administration window and
configuration will return to the camera image screen.
* Figures of 3. Administration and Configuration are taken from the 3MP model for web interface introduction purposes. Options within each item may differ slightly among series products and the differences will be marked in a NOTE.
Below are definitions of the tabs on the Live window.
Select Stream: Selects the viewable video stream that is displayed in live view (primary or secondary) and selects unicast or multicast settings.
Maximize Viewing Area: Scales the image to the full size of the browser. To resize the video pane to normal view, click the Show Toolbar button in the upper-right corner of the window.
Open Stream in New Window: Opens the video in a scalable, independent window. Opening the video in a separate window allows you to view the video while other applications are running. This window can be minimized, maximized, or closed using the title bar buttons of the active window. The window can also be resized to your specifications by dragging the lower-right corner of the window.
FIGURE 3-1: LIVE VIEW
19
3.1.1 Zoom and Focus Controls
NOTE: The zoom and focus controls, if available on your model, are viewable only after you have logged on to the device.
Zoom In: Click the button or click and drag the slider to zoom the lens in.
Zoom Out: Click the button or click and drag the slider to zoom the lens out.
Quick Auto-Focus: Click the button for the camera to start a quick search to find the optimal focal point for the scene.
3.2 Settings
Click on Settings, a window will pop up for configuring “System”, “Network”, “Imaging”, “A/V Streams”, “Users”, and
“Events”.
FIGURE 3-2: SETTINGS
3.2.1 System
Use the System tab to change the device name, configure the time settings, set up the text overlay for the live view, get backup, display system information and update firmware version. You can also use the System tab to generate a system log, reboot the camera, or to restore the camera's factory default settings.
20
Loading...