peerless-AV HD Flow HDS200-R User Manual And Installation Manual

ISSUED: 07-24-12 SHEET #: 180-9025-1
User Manual and Installation Guide
Pro Wireless Multimedia Kit
Models:
HDS200-R HD Flow Pro Wireless Multimedia Receiver
®
2 of 36
ISSUED: 07-24-12 SHEET #: 180-9025-1
Contents
Safety Precautions ..................................................................................................3
Proper Care and Safety ...........................................................................................3
Unit Care Recommendations .................................................................................3
Introduction ..............................................................................................................4
Features ................................................................................................................4
Package Contents .................................................................................................4
Product Specifi cations............................................................................................ 5
Video Format Supported .......................................................................................5
Audio Format Supported .......................................................................................5
Wireless Connection .............................................................................................5
Receiver ................................................................................................................6
Remote Control ...................................................................................................10
Multicast Programming ........................................................................................13
USB Multicast Setup Method ..............................................................................13
LAN Multicast Setup Method (Recommended) ...................................................13
Connecting your HD Flow Pro Wireless Transmitter or Receiver to the Computer
............................................................................................................................13
Transmitter Start-Up and Connection ..................................................................17
Transmitter Multicast Programming .....................................................................17
Receiver 1 LAN Programming .............................................................................20
Receivers 2+ Multicast Programming .................................................................22
Multicast Receiver 2, 3, and 4 Programming ......................................................23
Installation ..............................................................................................................26
Powering-up the HD Flow Pro Wireless Multimedia Receiver ............................27
Selecting Input and Output Port .........................................................................28
Indicator Lights Decoded .....................................................................................29
Appendix ................................................................................................................30
FCC Compliance .................................................................................................33
CE Compliance ...................................................................................................33
Warranty .................................................................................................................34
Contact Information ..............................................................................................35
3 of 36
ISSUED: 07-24-12 SHEET #: 180-9025-1
Unit can be placed vertically (preferred) or horizontally.
To clean, use a soft, dry cloth only. Do not use water or other cleaning products as they may cause electrical failure or damage the surface of the product.
Keep the product out of reach of children.
Keep the product away from external heat sources such as heaters or stoves.
If there is any unusual sound, smoke or odor coming from the product, immediately unplug the product and call Peerless-AV Customer care at 1-800-865-2112.
Keep the battery of remote control out of reach of children.
Do not attempt to open the outer case of the Transmitter or Receiver. Doing so will void the products warranty.
Keep the remote control away from humidity and/ or liquids.
Do not insert foreign objects into the unit.
Do not place the unit on an unstable surface or in a poorly ventilated area.
Make sure to plug the AC power adapters fi rmly into wall outlet.
Do not use near any ammable substances or combustible sprays.
If any part of the AC power adapter looks damaged, do not use the product and immediately call Peerless-AV Customer Care at 1-800-865-2112.
Keep the product unplugged if unused for an extended period of time.
Safety Precautions
Please read this manual before using the product.
Proper Care and Safety
Unit Care Recommendations
4 of 36
ISSUED: 07-24-12 SHEET #: 180-9025-1
The HD Flow Pro Wireless Multimedia Receiver expands the peer-to-peer kit to a multicast system that allows transmitting to up to 4 displays.
Features
• Low latency: ≤ 30ms.
Supports both digital (HDMI) and analog (Component, Composite) video/ audio.
Supports Wireless or Wired connection - IEEE 802.11n 5 GHz WiFi, LAN connection.
Two internal antennas (supporting MIMO).
HDCP v1.1 compliant.
Supports both DTV & VESA standards: DTV: 1920x1080i60/p60, 1280x720p60, 720x480i60/p60, VESA: WSXGA+(1680x1050), SXGA(1280x1024), WXGA(1280x800), XGA(1024x768), SVGA(800x600), VGA(640x480).
Supports passive 3D content.
Plug and play setup requires no software programming.
Package Contents
Ensure that the following items are present in the package. If any items are missing or damaged, please call Peerless-AV Customer Care at 1-800-865-2112 (available 7:00am - 7:00pm CST Monday - Friday).
Remote ControlReceiver
Manual
Stand
AC Adapter
Introduction
User Manual and Installation Guide
Pro Wireless Multimedia Kit
Models:
HDS200-R
®
5 of 36
ISSUED: 07-24-12 SHEET #: 180-9025-1
Product Specifi cations
1 x HDMI up to 1080p (60Hz) 1 x Composite 1 x YPbPr Component H.264 Baseline Profile with Level 4.2 HDCP compliant
Wireless Connection
Supporting IEEE 802.11n: OFDM RJ-45 LAN Port Direct Connection (LAN Cable) 1 x LAN Port 10/100 Base
USB
1 x USB Type A Female
Audio Output
1 x 3.5mm Audio Jack, 1 Stereo RCA Audio Jack
Video Resolution
480i/p, 720p, 1080i/p (24/30/60fps)
Streaming Latency
< 30ms
Frequency
5.15 - 5.25GHz
LAN Connection
10/100 Base
Range
131ft (40m)
Security
802.1x, 802.11i, WPA2, WPA and WEP 64/128 TKIP AES 2 x internal antenna MIMO Interface
IR Extender
IR-Extender
Color
Black Voltage: 12VDC
Amps: 2A Consumption: 12V 2A
Antenna Type
Power
HDS200-R
Video Output
Encoding
Wire Connection
LAN
Video Format Supported
• Digital Video
º HDMI - Up to 1080p @ 24Hz, 25Hz, 30Hz, 50Hz, 60Hz
• Analog Video
º Composite – 480i @ 60Hz, 70Hz, 85Hz º Component – 1080i @ 50Hz, 60Hz, 720p @ 50Hz, 60Hz º VGA – Up to 1920x1080 @ 50Hz, 60Hz
Audio Format Supported
The Receiver outputs stereo audio.
Wireless Connection
The HD Flow Pro Wireless Multimedia Receiver is capable of receiving Full HD 1080p media via a wireless connection or a wired connection from an HD Flow Pro Wireless Multimedia Transmitter.
6 of 36
ISSUED: 07-24-12 SHEET #: 180-9025-1
1
2
3
4
5 6
Receiver Front
Receiver
7 of 36
ISSUED: 07-24-12 SHEET #: 180-9025-1
Receiver Front
1. Power/Link
• Blinking indicator light - System booting or establishing link between the Trans-
mitter and the Receiver.
• Rapid blinking indicator light - Software upgrading or wireless/LAN mode switch-
ing.
• Solid indicator light - Link between the Transmitter and Receiver has been estab-
lished and is ready for signal transmission.
2. HDMI
• The HDMI indicator light will be illuminated when the HDMI port is selected for
video output.
If there is no signal, and/or the cable is not connected, the indicator light will blink.
3. COMPO
• The COMPO (component) indicator light will be illuminated when component
output is selected for video out.
If there is no signal, and/or the cable is not connected, the indicator light will blink.
4. A V
• The AV Indicator light will be illuminated when the AV port (composite) is
selected for the video output.
If there is no signal, and/or the cable is not connected the indicator light will blink.
5. IR Window
IR receiving window enables remote control of components.
6. Power/Source Selection Button
Press and hold for 3 seconds to turn on the unit.
When powered on:
º Press to select the video input source. Each press of the button will cycle
through the available video input "HDMI COMPO AV HDMI" in sequence.
º Press and hold for 8 seconds to turn the unit off.
8 of 36
ISSUED: 07-24-12 SHEET #: 180-9025-1
1
2
3 4
5
6
7
8
Receiver Back
9 of 36
ISSUED: 07-24-12 SHEET #: 180-9025-1
Receiver Back
1. HDMI-OUT
HDMI output port
2. A V -OUT
Composite output port
3. IR-IN
Connects IR Extender in order to extend IR reception range.
4. AUDIO-OUT*
Stereo audio output port
5. COMPONENT-OUT*
6. USB
USB port is used for fi rmware upgrades only.
7. LAN
LAN connection port is used for the following:
º Direct connection for LAN installations. º Direct connection to PC for system confi guration settings.
8. DC
DC Power Input
* For the audio part of a component media source, use the PC Audio Input port with a
3.5mm-to-RCA cable (not included).
10 of 36
ISSUED: 07-24-12 SHEET #: 180-9025-1
Remote Control
Remote Control Functions
1. POWER - Turns the Transmitter and Receiver power ON/OFF.
ON: If the Transmitter and Receiver are powered off and the Power/Link Indicator Light is on, press the power button pointed at either unit to turn on both units at the same time (this will take about 30 seconds).
ON: If the Transmitter and Receiver are powered off and the Power/Link Indicator Light is off, each unit will need to be turned on separately. Point the remote at each unit's IR Input Port and press the power button to turn on. (this will take about 1 minute and 30 seconds).
OFF: If the Transmitter and Receiver are powered on and the Power/Link Indicator Light is on, press the power button to turn off both units at the same time to put the system in Standby mode. The Power/Link Indicator Light will remain on.
OFF: If the Transmitter and Receiver are powered on and the Power/Link Indicator Light is on, press and hold the power button for 8 seconds. Both Transmitter and Receiver will be turned off at the same time. The Power/Link Indicator Light will turn off.
Note: If the Transmitter and Receiver are powered on with the Power/Link Indicator
Light fl ashing, both units will need to be powered off individually.
1
3
4 5
2
6
11 of 36
ISSUED: 07-24-12 SHEET #: 180-9025-1
2. INFO* - Displays the following information on the screen for:
Transmitter ** - WiFi Channel, Firmware Version, Audio/Video Input, and Source Resolution.
Receiver - Connection, Firmware Version, Video Output, Display Resolution, WiFi Reception Strength 1/5 to 5/5 (where 1/5 is the weakest signal and 5/5 is the strongest signal).
* Displayed information will disappear automatically after 10 seconds.
** The Transmitter unit’s information will only be displayed if the connection between
the Transmitter unit and Receiver has been established.
3. VIDEO OUT (Receiver) - Selects the AUDIO/VIDEO output port of the Receiver.
• HDMI - Selects HDMI as the AUDIO/VIDEO output.
• Component - Selects Component as the AUDIO/VIDEO output.
• AV - Selects AV as the AUDIO/VIDEO output.
.
Note: Remote must be pointing at the Receiver directly to control its output settings.
This may also be accomplished without the use of the remote control by toggling between outputs via the Power/Source Selection button.
4. LAN* (Red) - Selects LAN (wired) mode.
5. WiFi CH1** (Green) - Selects WiFi (Wireless) mode, Ch1.
6. WiFi CH2** (Yellow) - Selects WiFi (Wireless) mode, Ch2.
* Your new Receiver is set to WiFi mode. To change to LAN mode, press and hold the
LAN button for approximately 6 seconds or until the Link Indicator Light starts blinking.
** Your new Receiver is preset to WiFi Ch1. The channel setting on the new Receiver
MUST match the channel setting in your current system confi guration. Make sure that the connection between the new Receiver and the Transmitter is not established. (noted by a fl ashing Link Indicator Light). To change WiFi channel, press and hold the desired WiFi channel button for approximately 6 seconds or until the Link Indicator Light starts blinking.
Notes:
When you are pairing your new Receiver with your current HD Flow Pro Wireless Multimedia Kit the new Receiver MUST be on the same channel as your current kit.
Only the unit that receives the IR signal will change WiFi frequencies. For proper operation both Receiver and Transmitter units need to be on the same WiFi channel.
Loading...
+ 25 hidden pages