Panasonic SCEN35, SC-EN33 User Manual

SC-EN35 is used in the illustrations unless

otherwise mentioned.

If you have any questions contact

In the U.S.A.: 1-800-211-PANA (7262) In Canada: 1-800-561-5505

Operating Instructions

CD Stereo System

Dear customer

Thank you for purchasing this product. Before connecting, operating or adjusting this product, please read the instructions completely. Please keep this manual for future reference.

These instructions are applicable to the following systems.

System SC-EN35 SC-EN33

Main unit SA-EN35 SA-EN33

Speakers

SB-EN35

SB-EN35A

SB-EN33

SB-EN33A

Troubleshooting guide

Before requesting service, make the following checks. If you are in doubt about any of the check points, or if the solutions indicated in the chart do not solve the problem, refer to the “Customer Services Directory” on page 7 if you reside in the U.S.A., or refer to the “Product information” on page 7 if you reside in Canada.

The disc isn’t correctly set.

No play.

MP3 cannot be read.

Sound is unﬁxed, reversed or comes from one speaker only.

No sound or there is a lot of noise.

Humming heard during play. An AC power supply cord or ﬂuorescent light is near the cords. Keep other appliances and cords away from this unit’s cables.•

A beat sound or noise is heard while receiving a radio broadcast.

A low hum or noise is heard during AM broadcasts.

The picture on the television near the set disappears or stripes appear on the screen.

Remote control doesn’t work.

Display

--:--

PGM FULL The number of programmed tracks is limited to 24. No further tracks can be programmed.•

NO PLAY A CD-ROM disc that is not CD-DA or MP3 format is inserted. It cannot be played.• ERROR Incorrect operation performed. Read the instructions and try again.• F76 There is a power supply problem. Consult the dealer.•

XM Satellite Radio advisory messages

“ANTENNA” is ﬂashing.

“UPDATING” is ﬂashing.

“NO SIGNL” is ﬂashing.

“LOADING” is ﬂashing.

“OFF AIR” is ﬂashing.

“XM ---” is displayed. The selected XM channel is not available. Select a different channel.•

“XM RADIO” is displayed.

“---” is displayed.

You can receive only promotional XM channels.

• The disc is scratched or dirty. (Tracks skipped.)

• There is moisture on the lens. Wait for about an hour and then try again.

•

You may not be able to play MP3 if you have copied a multi-session disc that has no data between sessions.

• When creating a multi session disc, it is necessary to close the session.

• The amount of data on the disc is too small. Set the amount of data to greater than approximately 5 MB.

•

Check the speaker connections. (➡ page 3)•

Noise may occur when playing MP3 if recording quality is poor.

• Keep this unit away from mobile telephones if the interference is apparent.

• Turn the volume up.

• Switch the unit off, determine and correct the cause, then switch the unit on. Causes include shorting of the positive and

• negative speaker wires, straining of the speakers through excessive volume or power, and using the unit in a hot environment.

Switch the TV or other audio player off or separate it from the unit.

• Switch off the portable audio player connected to “MUSIC PORT”.

•

Keep the antenna away from other cables and cords.

• Keep the AM antenna away from the unit.

•

The location and orientation of the antenna are incorrect.

• The television antenna wire is too close to the unit. Separate the antenna wire of the television from the unit.

•

Check that the batteries are inserted correctly. (➡ page 2)

• Replace the batteries if they are worn.

•

You plugged the AC power supply cord in for the ﬁrst time and there was a power failure recently. Set the time. (

SC-EN35

The XM Connect & Play antenna, or XM Mini-Tuner and Home Dock is not properly connected.

• Check the connection and make sure the antenna cable not damaged. (➡ page 3)

•

The XM Connect & Play antenna, or XM Mini-Tuner and Home Dock is being updated with the latest encryption code.

• Wait a few seconds for the update to complete.

• You may have selected an XM channel that has been blocked, or is no longer available with your subscription package.

• If you want to inquire about receiving the channel, call XM’s Listener Care at 1-800-XMRADIO (1-800-967-2346).

•

The XM signal is too weak.

• Reorient the XM Connect & Play antenna, or XM Mini-Tuner and Home Dock for better reception.

•

The XM Connect & Play antenna, or XM Mini-Tuner and Home Dock is receiving and decoding the broadcast information.

• Wait a few seconds for loading to complete.

•

The selected XM channel is not currently broadcasting.

• Select a different channel.

•

It takes a short time for the XM radio to power up after turning on the main unit, during which time “XM RADIO” is displayed

• (only when the selected source is XM). Wait a few seconds for this process to complete.

•

Supplemental text information, such as the song title or artist’s name is not available for that particular broadcast.

• You can change the type of XM channel information that is displayed by pressing [DISPLAY].

•

Your XM Connect & Play antenna, or Mini-Tuner and Home Dock has not been activated, or your subscription has expired.

• To activate your XM Connect & Play antenna, or XM Mini-Tuner and Home Dock, or to renew your subscription, visit XM on

• the Web at www.xmradio.com or call XM’s Listener Care at 1-800-XMRADIO (1-800-967-2346). You should have your Radio ID ready.

Model No. SC-EN35

SC-EN33

➡ page 6)•

Panasonic Consumer Electronics Company, Division of Panasonic Corporation of North America

One Panasonic Way Secaucus, New Jersey 07094

http://www.panasonic.com

Panasonic Puerto Rico, Inc.

Ave. 65 de Infantería, Km. 9.5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985

Panasonic Canada Inc.

5770 Ambler Drive Mississauga, Ontario L4W 2T3

www.panasonic.ca

P PC

RQTV0162-3P

H0107FL3047

SA-EN35

Supplied accessories

The remote control

Use the numbers indicated in parentheses when asking for replacement parts.

(As of January 2007) In the U.S.A. to order accessories, refer to “Accessory Purchases” on page 7.

1 Remote control [➡ page 2] 1 AC power supply cord [➡ page 3]

SC-EN35

SC-EN33

(N2QAYB000105)

(N2QAYB000108)

(K2CB2CB00018)

1 FM/AM antenna [➡ page 3] 2 Batteries [➡ page 2]

(N1DADYY00003)

•

The included AC power supply cord is for use with this unit only. Do not use it with other equipment. Do not use an AC power supply cord from other equipment.

•

The included Canadian French language sheet corresponds to this unit’s English displays.

Control guide

SLEEP timer operation ON/OFF or SLEEP time setting

Standby/on switch

Clock and Timer setting [CLOCK/TIMER]

CD/MP3 Program, Tuner Preset (Manual) [PGM, -AUTO PRESET]

[Long press] Tuner Preset (Auto)

CD/MP3: Delete all programs [CLEAR]

[SLEEP]

[^]

R6/LR6, AA

Remote control signal sensor

[z PLAY] Timer PLAY ON/OFF

[;, OPEN/CLOSE] Open and Close CD lid

[1-9, 0, ≧10] Numbered buttons To select a 2-digit number

To select a 3-digit number

■ Batteries

Insert so the poles (+ and – ) match those

• in the remote control. Do not use rechargeable type batteries.

•

■ Use

Aim at the sensor, avoiding obstacles, at a

• maximum range of 7 m directly in front of the unit. Operation can be affected by strong light

• sources, such as direct sunlight, and the glass doors on cabinets.

e.g. 16: [≧10]  [1]  [6]

e.g. 226: [≧10]  [≧10]  [2]  [2]  [6]

Delete last programmed track [DEL]

[TUNER/BAND]

Selector switch to XM Band selection or Tuner for FM and AM

SC-EN35

Turn the volume up/down [VOL-], [+VOL]

SC-EN35SC-EN33

[ , ALBUM]

Previous/Next Album

[ , , XM CATEGORY <, >] MP3: Album skip XM: Category Channel Selector

[ENTER]

Conﬁrm track selection during MP3 Program Mode

[ALBUM ENTER] MP3: Conﬁrm track selection

during Program Mode XM: Exit Category mode

Preset EQ mode selector [PRESET EQ]

SC-EN35

FM/AM/XM select button [TUNER/BAND]

SC-EN33

FM/AM select button [TUNER/BAND]

Display

Standby/on switch [POWER 8]

Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power.

[CD q/h] Selector switch to CD. Direct CD Play/CD Pause

[MUSIC PORT] Selector switch to MUSIC PORT

[g] CD stop button

[2/u, 1\i] CD: Skip/Search MP3: Track Skip TUNER: Tune up/down, [Long press] Auto tuning

[PLAY MODE] Play mode button [SURROUND] SURROUND mode ON/OFF

[REPEAT] Repeat ON/OFF

[DISPLAY] CD: CD Display (Elapsed play time/Remaining play time) MP3: MP3 Display (Elapsed time/Album name/Track

name/ID3 [Album]/ID3 [Track]/ID3 [Artist])

SC-EN35

name/Category name/Title/Artist)

XM: XM Display (Channel number/Channel

[MUSIC PORT] Selector switch to MUSIC PORT

[g] CD stop button

[CD q/h] Selector switch to CD. Direct CD Play/CD Pause [; OPEN/CLOSE] Open and Close CD lid

[2/u, 1\i] CD: Skip/Search MP3: Track Skip TUNER: Tune up/down, [Long press] Auto tuning

[- VOLUME +] To adjust the volume

Remote control signal sensor

(Minimum)

Music port jack

(Maximum)

Placement of speakers

Right Speaker

AC power supply cord

2 3

Left and right speakers are different.

Left Speaker

DC in cord to connect to main set

Note

Keep your speakers at least 10 mm (13/32”) away

• from the system for proper ventilation. These speakers do not have magnetic shielding. Do

• not place them near televisions, personal computers or other devices easily inﬂuenced by magnetism. You cannot take the front net off the speakers.

•

Caution

Use the speakers only with the

• recommended system. Failure to do so may lead to damage to the ampliﬁer

and/or speakers, and may result in the risk of ﬁre. Consult a qualiﬁed service person if damage has occurred or if you experience a sudden change in performance. Do not attach these speakers to

• walls or ceilings.

Connections

SA-EN35 SA-EN35

AC IN

PGM

Page 2 for the position of remote control and

➡

main unit buttons.

1. Speakers

Copper (+)

Red

Black

Red

Silver (-)

Copper (+)

Headphones

(not included)

2. FM/AM antenna

Stand the antenna up on its base.

Taped part

FM antenna

AM antenna

Unplug the antenna connector by holding the taped part.

Connect the XM Connect & Play, or XM

Mini-Tuner and Home Dock (includes home antenna). (both not included)

XM Connect & Play or XM Mini-Tuner and Home Dock (includes home antenna)

To prevent interference with wireless equipment, place the antenna away from other equipment that emits radio waves (such as radio equipment and microwave ovens). Refer to page 5 for optimizing the reception.

Reduce the volume level and connect the headphones. Plug type: 3.5 mm (1/8”) stereo.

Note

To prevent hearing damage, avoid listening for prolonged periods of time .

4. AC power supply cord

 Connect the DC in cord from

left speaker to main set.

 Connect the AC power supply cord.

Connect the AC power supply cord after all other connections are complete.

To household AC outlet

Portable audio equipment

(Cords and equipment not included)

Portable audio player Plug type:

Use

MAIN UNIT

REMOTE CONTROL

➡

Note

Adjust the volume and sound quality of this unit and the other

• equipment. For details, refer to the instruction manual of the other equipment.

•

Conserving power

The unit consumes 2.0 W even it is turned off with [POWER 8]. To save power when the unit is not to be used for a long time, unplug it from the household AC outlet. Remember to reset the radio stations and any other memory items before using the unit again.

Note

If the unit is left unplugged for longer than approximately two weeks, all settings will revert to the factory settings.

3.5 mm (1/8”) stereo

Start Playback from the Portable audio source.

Discs operations

Basic play

 Press [POWER 8] to turn the unit on.  Press [; OPEN/CLOSE] to open the CD lid and then set the CD in place.

Press [; OPEN/CLOSE] again to close the lid.

Keep ﬁngers away from the CD lid when it is closing to avoid possible minor injury.

Label must face outward. Press until you hear it click into place.

 Press [CD q/h] to start play.  Adjust the volume.

Note

Be sure to press the [; OPEN/CLOSE] button to open and close the CD lid.

• Damage may occur if the lid is forced closed.

• During standby, if the CD is ready in the unit, the unit comes on and play begins.

•

(One touch play)

Stop

Pause

Skip/Search

Skip album Press [XM CATEGORY or ] /

MP3

Direct access play

(Play starts with the track you select.)

Press [g].

Press [CD q/h]. Press again to resume play.

Press [2/u] or [1/i] to skip/ Press and hold [2/u] or [1/i] to search.

Note

You can search during play or while paused.

• You cannot search through MP3 ﬁles.

• You can only search within the current track during

• program play, one track repeat, and random play.

SC-EN35 SC-EN33

[ALBUM or ] in the play mode.

SC-EN35 SC-EN33

Press [XM CATEGORY or ] / [ALBUM or ] once and then the numbered buttons in the

stop mode.

Press the numbered buttons to select the desired track.

MP3

SC-EN35 SC-EN33

 Press [XM CATEGORY or ] /

[ALBUM or ] to select the album.

 Press [1/i] once and then press the numbered buttons

select the desired track.

Program play

The function allows you to program up to 24 tracks.

 Press [PGM, -AUTO PRESET] while stopped.  Press the numbered buttons to select tracks. (Maximum 24 tracks)

Repeat this step to program other tracks.

 Press [CD q/h] to start play.

Track number

MP3

 Press [PGM, -AUTO PRESET] while stopped.  Press [XM CATEGORY or ] / [ALBUM or ] to

 Press [1/i] once and then press the numbered buttons to select tracks.

 Press [ALBUM ENTER] / [ENTER].

 Press [CD q/h] to start play.

Program contents are stored in the unit’s memory even after changing to a different function or turning the unit off. All program contents are erased by pressing [CLEAR] or by opening the CD lid.

SC-EN35 SC-EN33

select your desired album.

(Maximum 24 tracks)

SC-EN35 SC-EN33

Repeat step 2 to 4 to program other tracks.

Album number Track number

g Conﬁrm a programmed

track

g Delete all programs

g Cancel program mode

Note

Program number

Press [2/u] or [1/i] when “PGM” is displayed in the stop mode. To check while programming, press [PGM, -AUTO PRESET] twice after “PGM” appears, then press [2/u] or [1/i].

Press [CLEAR] in the stop mode. “CLR ALL” is displayed.

Press [PGM, -AUTO PRESET] in the stop mode to clear “PGM” indicator from the display.

+ 5 hidden pages