Panasonic AG-DVC 200E User Manual

Digital

te

Video
Casset

Digital Video Camera Recorder

AG- E

ENGLISHESPAÑOL ITALIANO FRANÇAIS DEUTSCH

Before attempting to connect, operate or adjust this product, please read these instructions completely.

1 (E)

≥ Batteries are used for the main power source and memory back-up in the product.

At the end of their useful life, you should not throw them away.
Instead, hand them in as small chemical waste.

≥ Voor de primaire voeding en het reservegeheugen van het apparaat wordt gebruikgemaakt van

een batterij.
Wanneer de batterij is uitgeput, mag u deze niet gewoon weggooien, maar dient u deze als klein
chemisch afval weg te doen.

Attention/Attentie

Main Power Battery (Ni-Cd Battery)
Batterij Voor Primaire Voeding (Nikkelcadmiumbatterij)

To remove the battery/Verwijderen van de batterij

Back-up Battery (Lithium Battery)
Batterij Voor Reservegeheugen (Lithiumbatterij)

Battery/Batterij
AU-BP402

Battery/Batterij AU-BP402

Anton/Bauer Battery
Anton/Bauer-Batterij

Unlocking lever
Ontgrendelingshefboom

L

O

C

K

CH1

RESET

COUNTER AUDIO SELECT

AUDIO IN

AUTO

MIC

FRONT

REAR

MIC
LIVE

MAN

TCG

TC
UB

ON
OFF

CH1 CH1

BREAKER

CH2

CH1 CH2

CH2

F-RUN

SET

R-RUN

MIC POWER

CH2

AUDIO LEVEL

POWER/
WARNING

QUICK FOCUS

MODE CHECK

SCENE FILE

MONITOR

AUTO IRIS MODE

FULL AUTO

VTR GAIN OUTPUT WHITE BAL

MENU

ON OFF

POWER

BACK.L

USER

STD

SPOT.L

1

F1

F2

F3

F4

STD

BARS CAM

ON

S

AVE

STB

Y

H LM

OFF

AUTO KNEE

PRST

A B

Back-up Battery (Lithium Battery)
Batterij Voor Reservegeheugen (Lithiumbatterij)

≥

If a battery made by any other manufacturer is to be used, check the Operating Instructions accompanying the battery.

≥

In geval u een batterij van een anden fabrikant zou gebruiken, gelieve dan eerst zorgvuldig de gebruiksaanwijzing van
deze batterij te lezen.

≥ For the removal of the battery for disposal at the end

of its service life, please consult your dealer.

≥ Raadpleeg uw leverancier over de verwijdering van

de batterij op het moment dat u het apparaat bij einde
levensduur afdankt.

Precautions for Use

2 (E)

ENGLISH

CAUTION:

TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD AND ANNOYING INTERFERENCE,
USE THE RECOMMENDED ACCESSORIES
ONLY.

ª

DO NOT REMOVE PANEL COVER BY
UNSCREWING.

To reduce the risk of electric shock, do not remove
cover. No user serviceable parts inside.
Refer servicing to qualified service personnel.

CAUTION

Danger of explosion if battery is incorrectly
replaced.
Replace only with the same or equivalent type
recommended by the equipment manufacturer.
Discard used batteries according to
manufacturer’s instructions.

VARNING

Explosionsfara vid felaktigt batteribyte. Använd
samma batterityp eller en ekvivalent typ som
rekommenderas av apparattillverkaren. Kassera
använt batteri enligt fabrikantens instruktion.

ADVARSEL!

Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri af samme
fabrikat og type. Levér det brugte batteri tilbage
til leverandøren.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti
asennettu.
Vaihda paristo ainoastaan laitevalmistajan
suosittelemaan tyypiin. Hävitä käytetty paristo
valmistajan ohjeiden mukaisesti.

Lithium Battery

Warning

The lithium battery in this equipment must only be
replaced by qualified personnel. When necessary,
contact your local Panasonic supplier.

“The lithium battery is a critical component (type
number CR2032 manufactured by Panasonic.)

It must never be subjected to excessive heat or
discharge. It must therefore only be fitted in
equipment designed specifically for its use.

Replacement batteries must be of the same type
and manufacturer. They must be fitted in the same
manner and location as the original battery, with
the correct polarity connections observed.

Do not attempt to re-charge the old battery or re­use it for any other purpose. It should be disposed
of in waste products destined for burial rather than
incineration.”

indicates safety information.

Precautions for Use

WARNING:

TO REDUCE THE RISK OF FIRE OR SHOCK
HAZARD, KEEP THIS EQUIPMENT AWAY
FROM ALL LIQUIDS-USE AND STORE ONLY
IN LOCATIONS WHICH ARE NOT EXPOSED
TO THE RISK OF DRIPPING OR SPLASHING
LIQUIDS, AND DO NOT PLACE ANY LIQUID
CONTAINERS ON TOP OF THE EQUIPMENT.

This camera recorder is designed to be used exclusively with the standard size of DV tapes. Do not use DVCPRO tapes or other
sizes of tapes.

3 (E)

Contents

Precautions for Use..........................................1

Introduction.......................................................4

Features.............................................................4

Features of the camera unit....................................4

Features of the VTR unit.........................................4

System configuration.......................................5

Parts and their functions..................................6

Preparation......................................................10

Using the AU-BP402 or AJ-BP490

battery pack made by Panasonic..........................10

Using a battery pack made by Anton Bauer..........11

Using the NP-1B battery pack made by Sony.......11

Using an AC power supply

(with the AJ-B75 AC adapter) ...............................12

Attaching the lens..................................................12

Mounting the unit on a tripod.................................13

Detaching the unit from the tripod attachment......13

Attaching the viewfinder and microphone.............13

Attaching the shoulder belt (optional accessory) ..13

Setting the camera ID ...........................................14

Setting the date and time......................................14

Lens adjustments and checks.......................15

Flange back adjustment........................................15

White shading check.............................................15

White shading adjustment.....................................15

Viewfinder displays ........................................16

Viewfinder lamp displays.......................................16

Viewfinder screen status displays.........................16

Selecting the viewfinder screen display................19

White balance and black balance adjustment

....20

Automatic white balance adjustment.....................20

Automatic black balance adjustment.....................20

Electronic shutter settings.............................21

Shutter modes.......................................................21

Setting the shutter mode and speed.....................21

Setting the synchro scanning mode......................21

Time data settings ..........................................22

Setting the user’s bit..............................................22

Setting the time code ............................................22

Scene files.......................................................23

Scene file function.................................................23

Scene file setting method......................................23

Editing scene filenames (Example: USER files) ...23

Returning a scene filename to its default..............24

How to use file select............................................24

List of scene file settings.......................................25

List of file settings..................................................25

Normal recording............................................26

Recording methods...............................................26

Scene-to-scene continuity.....................................26

Audio recording..............................................27

Selecting the audio input signals...........................27

Adjusting the audio recording level.......................27

Monitoring the sound during recording..................27

Playback (checking what has been recorded)

....28

Rec review ............................................................28

Other functions...............................................28

Still-picture playback.............................................28

INTERVAL REC (intermittent recording) function

.......28

Variable speed (FF/REW) playback......................28

INDEX SEARCH mode.........................................28

Using the unit with external components.....29

Connection to a video component

with a DV connector..............................................29

Connection to a PC capable of non-linear editing

.......29

Menu operations.............................................30

Menu display enable/disable.................................30

Displaying sub-menus and deciding on settings...30

Setting menu configuration...........................31

Menu contents.................................................32

SCENE menu (main menu)...................................32

MAIN menu 1 of 2 (main menu)............................33

MAIN menu 2 of 2 (main menu)............................35

Warning system..............................................38

Emergency eject .............................................39

Maintenance....................................................40

Condensation........................................................40

Replacing the backup battery................................40

Cleaning the heads...............................................40

Cleaning inside the viewfinder ..............................40

Phenomena inherent to CCD cameras.................40

Error codes......................................................40

Specifications .................................................41

4 (E)

ENGLISH

Features

Introduction

This is the first DV format integrated camera VTR that supports
standard cassettes. It combines the digital camera technology
fostered by broadcast equipment with the dependability of the
DVCPRO mechanism. It has a compact size, light weight and low­power consumption, and it is capable of recording for many hours.

Both its camera unit and VTR unit incorporate digital signal
processing to achieve even greater improvements in picture quality
and stability.

Features of the camera unit

≥1/2 type IT 3-CCD configuration

The camera’s high resolution of about 800 lines and its minimum
subject brightness of 0.5 lux make easy work of shooting under
low lighting conditions, and they achieve bright camera images
with a high sensitivity.

≥Digital processing incorporated

Full-blown digital processing circuitry fostered by broadcasting
applications is featured to ensure a high performance,
sophisticated functions and a high level of dependability.

≥Replacement lens system

The bayonet system is employed to enable 1/2 lenses made by
Fujinon or Canon to be mounted for use.

≥CC/ND filter with a 4-leaf configuration

adopted as a standard accessory

This configuration enables the optimum filter for the subject
brightness and colour temperature to be selected.

≥Shooting support functions

Scene file dial

This makes it easy to select six scene file settings to suit the
prevailing shooting conditions.

ATW (auto tracking white) function

The auto tracking white function comes in handy when
shooting successive scenes with different light sources.

Quick focus function

This automatically controls the iris and shutter to provide
support for ensuring easy focusing.

Full auto function

This is useful for emergency shooting when, for instance,
there is not enough time to perform the camera settings.

Auto iris mode selection function

This enables three auto iris settings to be selected. The
settings can easily be switched to match the shooting
conditions.

Menu jog dial system

A jog dial button enabling easy menu settings is provided on
the front panel of the camera.

Features of the VTR unit

≥DV format

The VTR unit compresses the images using a component digital
recording system that incorporates the latest compression
technology. For recording the sound, the unit uses non­compression PCM recording which achieves an excellent signal­to-noise ratio, frequency band, waveform characteristics and
reproducibility of the finely detailed parts. Both picture quality
and sound quality are taken to new heights by this format.

≥Standard tape drive

The DVCPRO mechanism with its proven track recorded in
broadcasting applications has been put to use to ensure the
same high level of dependability while at the same time enabling
long recordings lasting up to a maximum of 270 minutes.

≥High system capabilities

The unit comes with DV connectors as a standard accessory.
These enable hookup with other DV components and DV non­linear devices.
The battery packs made by Anton Bauer and battery systems
made by other companies are all supported.

≥Other features

Frame-to-frame continuity

Simply by pressing the VTR START button or VTR button on
the lens, the continuity from one frame to the next is assured
with a precision of 0 to +1 frame or less.

Rec review function

This automatically rewinds the tape for the last 2 to 10
seconds recorded and plays back the recording. This
enables what was recorded to be monitored without delay.

Built-in time code generator/reader

This enables the time code information to be recorded on the
dedicated sub-code track and played back.

Time stamp function

This superimposes the date and time onto the camera’s
images and records them.

Interval rec function

This function enables simply interval shooting. It is
particularly effective for shooting programmes on nature or
art.

5 (E)

System configuration

Mic kit:
AJ-MC700

Wireless mic
receiver:

WX-RJ700

Mic holder:
AJ-MH700

Lens (bayonet type):
FUJINON/CANON

Rain cover:
SHAN-RC700

Soft carrying case:
AJ-SC900

Battery case:
AU-M402H

Battery
case/holder

AC adapter:
AJ-B75

Cassette tapes:
AY-DV124MQ
AY-DV124PQ
AY-DV186MQ
AY-DV186PQ
AY-DV276MQ

Cleaning tape:
AY-DVCL

Battery
chargers:

AG-B425
AJ-B450

Panasonic batteries:
AU-BP402
AJ-BP490

Anton Bauer batteries

Sony batteries:
BP-90
BP-L60/L90
NP-1B

1/5˝ viewfinder:
AJ-VF10
AJ-VF15

Digital Video Camera Recorder
AG-DVC200E

<Note> Checking the lens shading compensation

This unit comes with a function which provides shading compensation for the lens. Check that the compensation is optimum for the type
of lens used. For further details, refer to “Lens adjustments and checks” (page 15).

Lens classification

Lens type

A B

S18 a 6.7BERM4
S18 a 6.7BRM4
S19 a 6.5BERM4
S19 a 6.5BRM4
YH18 a 6.7IRS
YH12 a 4.8IRS

YH18 a 6.7KRS/KP
(For AG-DVC200D)
YH14 a 7.3KRS
YH12 a 4.8KRS
S14 a 7.5BRM4
S17 a 6.6BRM4

C

S14 a 7.3BRM
(For AG-DVC200L)

USER

Lens other than A, B or C

Lens shading compensation data selection

6 (E)

ENGLISH

Parts and their functions

1

POWER switch

This switch turns the power ON and OFF.

4

OUTPUT/AUTO KNEE selector switch

This switch selects the video signals which are to be output from
the camera unit to the VTR unit, viewfinder and/or video
monitor.

CAM, AUTO KNEE ON:

The images shot by the camera are output. The AUTO
KNEE circuit operates.

CAM, AUTO KNEE OFF:

The images shot by the camera are output. The MANUAL
KNEE circuit operates.

BARS:

Colour bar signals are output. The AUTO KNEE circuit
does not operate.

1B

<:

@

;

9

A

?

=

>

8

6

7

5432

3

GAIN selector switch

When the camera screen is dark, turn this switch to a position
which will increase the gain and brighten the screen.
The gain for each item can be selected on-screen. For further
details, refer to the table for <SW MODE> in the section on the
setting menu screens (page 33).
L:The switch is normally set to this position. The gain at this

position was set to 0 dB at the factory prior to shipment.

M:The gain of the camera’s video amplifier is increased. The

gain at this position was set to 9 dB at the factory prior to
shipment.

H:The gain of the camera’s video amplifier is increased even

more. The gain at this position was set to 18 dB at the
factory prior to shipment.

2

VTR STBY/SAVE (tape protection) switch

This switches the power supply mode when the VTR is set to
the rec pause mode in which recording is temporarily
suspended.
STBY:In this mode, recording starts immediately by pressing

the VTR START button.

SAVE:This is the tape protection mode. The tape drum is

stopped in the half-loading status. Less power is
consumed at this position than at the STBY position so
that the battery will supply power to the unit for a longer
period of time.
Compared with the STBY position, more time is taken to
start recording after the VTR START button is pressed.
When the switch is set to the SAVE position, the VTR
SAVE lamp inside the viewfinder lights up.

<Note>

When the PAUSE TIMER time has elapsed in the STBY mode,
the unit is automatically set to the SAVE mode. For further
details, refer to the table for <VTR OPTION> in the section on
the sub-menu screens (page 34).

AUTO KNEE function

When shooting with the level set to people or scenes against a
high-brightness background, the background will be whitened
out, and the buildings and scene in the background will be
blurred. If the AUTO KNEE function is activated at times like
this, the background will be reproduced clearly. This function
is effective for shooting in the following situations:

≥When shooting people in the shade under a clear sky
≥When simultaneously shooting people in a car or indoors

and the outside scenery through a window

≥When shooting scenes with a strong contrast

RESET

COUNTER AUDIO SELECT

AUDIO IN

AUTO

MIC

FRONT

REAR

MIC

LINE

MAN

TCG

TC

UB

ON

OFF

CH1 CH1 CH2

CH1

CH2

CH2

F-RUN

SET

R-RUN

MIC POWER

G

DC E F

HI

5

WHITE BAL (white balance memory
selector) switch

A or B: When the AUTO W/B (white/black) BAL switch on the

front panel is operated to adjust the automatic white
balance, the adjusted value is automatically stored in A
or B.

PRST : The colour temperature is set to 3200K in the preset

mode. The AUTO W/B BAL switch does not work at this
position.

<Reference>

The automatic tracking white balance mode (ATW) can be set to
A, B or PRST. For further details, refer to the table for <SW
MODE> in the section on the sub-menu screens (page 33).

7 (E)

Parts and their functions

B

MENU button

This is used to switch the menu ON and OFF.

A

JOG dial button

This is used to select the menu items and perform settings when
the MENU button B is at the ON position. When the synchro
scanning mode has been selected for the shutter speed, the
shutter speed can be easily adjusted more finely.

?

FULL AUTO button

This is pressed when there is no time to check the camera unit’s
settings. The lens iris and white balance will be automatically
adjusted.

@

FULL AUTO lamp

This lights up when FULL AUTO shooting is being performed.

>

AUTO IRIS MODE selector switch

This is used to select the position that matches the shooting
conditions when shooting by automatically adjusting the lens
iris.

BACK.L: When making a back-lit subject brighter for shooting
STD :For normal shooting
SPOT.L : For shooting a spot-lit subject

=

QUICK FOCUS button

This supports the focusing of the subject. When it is pressed,
the lens iris is opened for about 10 seconds. It makes the depth
of field shallower and facilitates focusing.

<

MODE CHECK button

This enables the setting modes of the camera’s control switches
to be checked in the viewfinder.

;

SCENE FILE dial

This enables the camera settings that match the shooting
conditions to be selected. For further details, refer to “How to
use file select” (page 24).

:

SPEAKER

The sound can be monitored through this speaker.
When an earphone is connected to the PHONE jack, the sound
of the speaker will be automatically cut off.
What can be monitored is the mixed sound of CH1 and CH2.

7

MONITOR (volume) control

This is used to adjust the volume of the monitor speaker or
earphone.

8

AUDIO LEVEL CH1, CH2 (audio channel 1,
2 recording level) controls

These are used to adjust the CH1 and CH2 recording levels
while monitoring the level meter inside the viewfinder.

9

POWER/WARNING lamp

This lamp lights up green when the power is turned on, and it
flashes in green during interval recording. When a warning is
given, it lights up red or flashes in red to alert the user. For
further details, refer to “Warning system” (page 38).

6

BREAKER switch

If an excessively high current flows inside the unit due to some
problem or other, the circuit breaker is tripped and the power is
automatically turned off to protect the unit.
Push this button in after conducting an inspection or repairs
inside the unit. If there are no problems, the power will come
back on.

D

COUNTER selector switch

This is used to switch the counter display.
COUNTER : A relative numerical value is displayed by the

counter. However, when the tape recording
includes discontinuous parts, the counter reading
may also lack continuity.

TC : The time code is displayed.
UB :The user’s bit is displayed.

E

TCG selector switch

This sets the time code operation mode to FREE RUN, REC
RUN or SET. For further details, refer to “Time data settings”
(page 22).

F

AUDIO SELECT CH1, CH2 (audio channel 1,
2 auto/manual level adjustment selector)
switches

These are used to select the method used to adjust the audio
levels of audio channels 1 and 2.

AUTO:The audio level is adjusted automatically.
MAN: The audio level is adjusted manually.

H

Mic power switches

These are used to turn the phantom power (+48V) for each rear
jack channel ON and OFF.

<Note>

ON or OFF can be set for supplying the phantom power of the
front microphone using “FRONT MIC POWER” on the
<MIC/AUDIO> sub-menu screen.

G

AUDIO IN (audio input selector) switches

These are used to select the input signals to be recorded on
CH1 and CH2.

FRONT: The input signals from the microphone connected to
(MIC) the MIC IN connector are recorded.
REAR :The input signals from the microphone connected to
(MIC) the AUDIO IN CH1/CH2 connector are recorded.
REAR :The input signals from the line connected to the
(LINE) IN CH1/CH2 connector are recorded.

C

RESET button

This is used to reset the numerical value of the counter or time
code.

<Note>

This value is reset immediately when the COUNTER has been
selected. When TC or UB has been selected, the reset button
works only when the TCG selector switch is at the SET position.

I

Backup battery compartment

For further details on replacing the backup battery, refer to
“Replacing the backup battery” (page 40).

8 (E)

ENGLISH

Parts and their functions

4

1

2
3

=

@

5
6

>

789

:

?

;

<

4

AUTO W/B (white/black) BAL switch

AWB :The white balance is automatically adjusted. When the

AWB memory selector switch on the side panel is set to
A or B and then the AUTO W/B BAL switch is operated,
the adjustment value is recorded in the memory. Bear in
mind that the switch does not work when it is set to the
ATW or PRST position.

ABB : The black balance is automatically adjusted.

1

CC/ND filter selector knob

This is used to select the filter to match the subject brightness.

1 :3200K
2 :5600K+1/8ND
3 :5600K
4 :5600K+1/64ND

5

SHUTTER switch

This is the ON/OFF selector switch of the electronic shutter.

OFF : The electronic shutter does not operate.
ON : The electronic shutter operates.
SEL : This is used when the electronic shutter speed is to be

changed. The switch is a non-locking type. The shutter
speed changes each time it is operated. For further
details, refer to “Electronic shutter settings” (page 21).

6

VTR START/STOP button

This starts or stops the video recording.

3

Lens mount (bayonet type)

The lens is attached to this mount.

7

LENS jack (12-pin)

The connecting cord of the lens is connected to this jack. For
further details on the lenses that can be used, refer to the
operating instructions of the lenses concerned.

8

MIC IN (mic input) jack (XLR, 3-pin)

The accessory microphone is connected to this jack. The power
for the microphone is supplied from this jack.

2

Lens lever

This lever is tightened to secure the lens after the lens has been
attached to the lens mount.

:

GENLOCK IN connector (BNC)

Supply the sync signal (black burst signal) to this connector
when gen-locking the camera pictures (CAM OUT jack) of the
unit.

9

AUDIO OUT jacks (pin jacks)

An audio component is connected to these jacks. The sound for
channel 1 and channel 2 is output separately.

>

Viewfinder stopper screw

This screw is used to secure the viewfinder.

?

Light shoe

The video light or other such device is attached here.

@

Shoulder belt fittings

The shoulder belt (optional accessory) is attached here.

<

S-VIDEO OUT jack (Y/C jack)

When pictures are to be recorded with a backup VTR connected
to the S-VIDEO OUT jack, bear in mind that the unit’s playback
pictures will be recorded onto the backup VTR if any operation
(such as REC CHECK) that performs VTR playback is
executed.

;

CAM OUT jack

This is the dedicated output jack for the camera’s pictures.

=

Viewfinder connector

The viewfinder plug is connected to this connector.

Parts and their functions

1

2

3

4

5

67

1

TALLY lamp

This lights up when the unit is set to the recording mode. It
flashes when it is being transferred to the recording mode.

2

External DC input socket

This is the input socket of the external power supply (DC power
supply). When an AC adapter is connected here, power is
automatically supplied from the external source.

3

AUDIO IN CH1, CH2 (audio input channel 1,

2) jacks (XLR, 3-pin)

An external microphone or line input signals are connected to
these jacks.

4

DV I/F connector (complying with IEEE
1394 standard)

A digital video component or computer equipped with a DV
connector is connected to this connector using a DV cable
(optional accessory). For further details, refer to “Using the unit
with external components” (page 29).

5

DC OUT (DC power supply) output socket

This normally serves as the DC 12 V output socket. A current of
approximately 1 A can be taken out.
When the HDD adapter scheduled to be developed in the future
is connected here, it will be possible to supply a 7 V voltage.

6

VIDEO OUT jack (BNC)

This is the composite video jack for a monitor.

<Note>

When pictures are to be recorded with a backup VTR connected
to the VIDEO OUT jack, bear in mind that the unit’s playback
pictures will be recorded onto the backup VTR if any operation
(such as REC CHECK) that performs VTR playback is
executed. Use the exclusive camera output jack for backup
recording.

8

6

/

REW FF

EJECT

STOP PLAY/PAUSE

ª

9

7

PHONES (earphones) jack (mini jack)

The earphones (stereo) for monitoring sound are plugged in
here. When the earphones are connected, no sound will be
output from the speaker.

8

REW (rewind)/FF (fast forward) buttons/

8

5

/

1/;

:;

lamps

≥When one of these buttons is pressed in the stop mode, the

high-speed playback (rewind or fast forward) mode is
established, and the corresponding lamp lights.

≥When one of these button is pressed in the playback mode,

the 4a speed playback (rewind or fast forward) mode is
established, and when the same button is pressed again, the
8a speed playback (rewind or fast forward) mode is
established.
Each time the button is then pressed, the mode is switched
between 4a speed playback and 8a speed playback.

≥When one of these buttons is pressed in the STILL or REC

PAUSE mode, the 1a speed playback (rewind or fast forward)
is established while the button is held down. When the button
is released, the unit returns to the previous mode (STILL or
REC PAUSE).
The variable speed playback mode is released by pressing the
STOP button, PLAY/PAUSE button or EJECT button.

9

STOP button

The tape stops travelling when this button is pressed. However,
the button cannot be operated during recording. To stop
recording, first set the unit to the REC/PAUSE mode, and then
press the STOP button.

:

PLAY/PAUSE button/lamp

Playback commences when this button is pressed, and the lamp
lights. When it is pressed again, the STILL mode is established,
and the lamp flashes.
When it is pressed once more, the playback mode is restored.

;

EJECT button

When this button is pressed, the cassette holder rises, and the
cassette tape can be inserted or removed. This button cannot
be operated while the unit is recording, in which case first set
the unit to the REC/PAUSE mode, and then press the EJECT
button.

9 (E)

10 (E)

ENGLISH

3

Connect the plug of the battery pack to the
connector inside the battery case, and
insert the battery pack into the case.

<Note>

Ensure that the power is turned off before connecting or
disconnecting the plugs.

AU-BP402
battery pack

Label
surface

Preparation

Using the AU-BP402 or AJ-BP490 battery pack made by Panasonic

1

Remove the battery holder.

Disconnect these.

2

Attach the battery case to the unit.

Battery holder

Recharge the battery pack using the battery charger specifically designed for each individual battery pack. For the charging time and other
details, refer to the operating instructions of the battery charger used.

Disconnect these.

Connect here.

Rubber capsScrews

AU-M402H
battery case

1Connect the unit’s cable with the cable of the AU-M402H

battery case.

2Use a screwdriver to attach the AU-M402H battery case to

the unit.
The holes for tightening the screws can be seen when the
cover is opened and the rubber caps are raised. Use a
screwdriver to tighten the screws, and attach the battery
case to the unit. Ensure that the screws are tightened up as
far as they will go.

<Note>

≥Do not pull the rubber caps with great force.
≥Be careful not to catch up the cables when attaching the

battery case.

4

Set the battery type.

Select the battery type using <BATTERY> on the sub-menu
screen.
Select “TYPE A” if the AJ-BP490 is to be used; select “NiCd12”
if the AU-BP402 is to be used. (See page 34)

11 (E)

Preparation

Using a battery pack made by
Anton Bauer

1

Attach the battery pack made by Anton
Bauer.

2

Insert the battery pack and slide it in the
direction of the arrow.

Power output connector for lighting

Battery pack made by Anton Bauer

Before use, charge the battery pack using the exclusive battery
charger made by Anton Bauer.
For the charging time and other details, refer to the operating
instructions of the battery charger used.

Lighting control switch

<Reference>

A battery holder made by Anton Bauer is equipped with a power
output connector for the lighting and a lighting control switch to
enable a light to be easily attached. For details on the lighting
systems available, contact Anton Bauer.

3

Set the battery type.

Select the battery type using <BATTERY> on the sub-menu
screen.
Example:Select “NiCd13” if the TRIMPAC13 is to be used;

select “NiCd14” if the TRIMPAC14 is to be used.
(See page 34)

3

Set the battery type.

Select the battery type using <BATTERY> on the sub-menu
screen.
Select “NiCd12” if the NP-1B is to be used. (See page 34)

<Reference>

To remove the battery pack, slide it in the opposite direction to the
one in which it was attached while keeping the release lever on the
battery holder pulled down all the way.

Release lever

2

Using the NP-1B battery pack
made by Sony

Before use, charge the battery pack using the exclusive battery
charger made by Sony.
For the charging time and other details, refer to the operating
instructions of the battery charger used.

Refer to step 1 on page 10.

1

Remove the battery holder.

2

Attach the battery made by Sony to the
unit.

Screw provided
with mounting
connector for
NP-1B

Mounting
connector for
NP-1B

Cover

2

1

3

4

5

Battery case

Hole

First, remove the battery holder cover.

1 Attach the mounting connector for the NP-1B.
2 Use the mounting screws to mount the battery case.
3 Tighten the screw for the power supply contact.
4 Insert the top of the cover in the direction of the arrow.
5 Align the hole in the bottom of the cover (metal part) with the

hole in the bottom of the battery case, and attach using the
screw provided with mounting connector for NP-1B.

12 (E)

ENGLISH

Attaching the lens

1

Raise the lens lever, and remove the
mount cap.

4

Push the cable into the cable clamp, and
connect it to the LENS jack.

Mark

3

Pull down the lens lever to secure the
lens.

LENS jack

<Notes>

≥For details on how to handle the lens, refer to the operating

instructions of the lens.

≥While the lens is removed, attach the mount cap to protect the

unit.

Preparation

Using an AC power supply
(with the AJ-B75 AC adapter)

1

Connect the unit’s external DC input
socket with the DC OUT socket on the AJ­B75 AC adapter.

2

Turn on the AC adapter’s power.

5

Proceed with the flange back adjustment
for the lens.

3

Set the unit’s POWER switch to ON.

When an AC adapter other than the AJ-B75 is to be used,
check the pin signals of the external DC input socket.

<Notes>

≥When both a battery pack and an AC adapter have been

connected, the power supplied from the AC adapter takes priority.
It is also possible to attach/remove a battery while the AC adapter
is being used.

≥When an AC adapter is to be used, the unit’s POWER switch must

be set to ON only after the AC adapter’s power has been turned
on. If the power is switched on in the reverse sequence, the AC
adapter’s output voltage will rise slowly, possibly causing the unit
to malfunction.

Pin No Signal

1 GND

2, 3 –

4 +12 V

1

2

3

4

External DC input socket

External DC input
socket

AC adapter
≥AJ-B75 (optional accessory)

Lens lever

Mount cap

2

Fit the centre mark on the lens into the
centre cutout on the top of the lens mount,
and attach the lens.

13 (E)

Preparation

Tripod attachment

Mounting the unit on a tripod

1

Mount the tripod attachment on the tripod.

Use the tripod attachment to mount the unit on a tripod.

For details on the attachment and adjustments of the viewfinder and
microphone, refer to the operating instructions of the viewfinder.

<Note>

Take account of the centre of gravity of the unit and that of the
tripod attachment when selecting the attachment hole. Check that
the diameter of the hole selected matches the diameter of the tripod
head screw.

2

Mount the unit on the tripod attachment.

Slide the unit along the groove toward the front until it clicks into
place.

Tripod head

Tripod attachment

Detaching the unit from the
tripod attachment

Red lever

While pushing down the red lever, move the black lever in the
direction of the arrow and slide the unit toward the back to remove
it.

<Note>

If the pin of the tripod attachment fails to return to its original
position after the unit has been detached, again move the black
lever in the direction of the arrow while pushing down the red lever,
and return the pin to its original position. Bear in mind that the unit
cannot be attached if the pin remains in the centre.

Black lever

Attaching the shoulder belt
(optional accessory)

Attaching the viewfinder and
microphone

Shoulder belt

The tab opens
when it is
pressed.

<Note>

Check that the shoulder belt is attached securely.

To disengage the shoulder belt,
open the tabs of the attachment
parts, and disengage.

The tab opens
when it is
pressed.