Onkyo TX-DS494 User Manual

AV Receiver

TX-DS494

Instruction Manual

Contents

Before using

Important Safeguards ....................................... 2

Precautions........................................................ 3

Features ............................................................. 4

Supplied accessories ......................................... 4

Before using this unit ....................................... 5

Facilities and connections

Front panel facilities ......................................... 6

Remote controller ............................................. 9

Rear panel facilities ........................................ 10

Example of how to connect your equipment . 12

Positioning speakers ....................................... 16

Connecting speakers ....................................... 17

Connecting antennas....................................... 18

Connecting the power ..................................... 20

Thank you for purchasing the Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference.

Enjoying music or videos

Speaker Setup ................................................. 21

Selecting a sound source ................................ 22

Listening to Radio Broadcasts........................ 24

To enjoy Surround mode ................................ 26

Recording a source ......................................... 29

Remote controller

Using remote controller .................................. 30

Pre-programming remote controller

(North American models only) .................... 32

Appendix

Troubleshooting guide .................................... 34

Specifications ........................... back cover page

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Important Safeguards

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

AVIS

RISQUE DE CHOC ELECTRIQUE

OUVRIR

NE PAS

1. Read Instructions – All the safety and operating instructions should be read before the appliance is operated.

2. Retain Instructions – The safety and operating instructions should be retained for future reference.

3. Heed Warnings – All warnings on the appliance and in the operating instructions should be adhered to.

4. Follow Instructions – All operating and use instructions should be followed.

5. Cleaning – Unplug the appliance from the wall outlet before cleaning. The appliance should be cleaned only as recommended by the manufacturer.

6. Attachments – Do not use attachments not recommended by the appliance manufacturer as they may cause hazards.

7. Water and Moisture – Do not use the appliance near water –for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

8. Accessories – Do not place the appliance on an unstable cart, stand, tripod, bracket, or table. The appliance may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the appliance. Any mounting of the appliance should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

9. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

10. Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the appliance and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the appliance on a bed, sofa, rug, or other similar surface. The appliance should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided. There should be free space of at least 20 cm (8 in.) and an opening behind the appliance.

11. Power Sources – The appliance should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company.

12. Grounding or Polarization – The appliance may be equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

PORTABLE CART WARNING

S3125A

13. Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

14. Outdoor Antenna Grounding – If an outside antenna or cable system is connected to the appliance, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure 1.

15. Lightning – For added protection for the appliance during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the appliance due to lightning and power-line surges.

16. Power Lines – An outside antenna system should not be lo- cated in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17. Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

18. Object and Liquid Entry – Never push objects of any kind into the appliance through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the appliance.

19. Servicing – Do not attempt to service the appliance yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

20. Damage Requiring Service – Unplug the appliance form the wall outlet and refer servicing to qualified service personnel under the following conditions: A. When the power-supply cord or plug is damaged, B. If liquid has been spilled, or objects have fallen into the

appliance, C. If the appliance has been exposed to rain or water, D. If the appliance does not operate normally by following

the operating instructions. Adjust only those controls that

are covered by the operating instructions as an improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the appliance to its normal operation, E. If the appliance has been dropped or damaged in any way,

and F. When the appliance exhibits a distinct change in perfor-

mance – this indicates a need for service.

21. Replacement Parts – When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

22. Safety Check – Upon completion of any service or repairs to the appliance, ask the service technician to perform safety checks to determine that the appliance is in proper operation condition.

23. Wall or Ceiling Mounting – The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.

24. Heat – The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.

Precautions

FIGURE 1: EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

ANTENNA LEAD IN WIRE

GROUND CLAMP

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

ELECTRIC SERVICE EQUIPMENT

NEC – NATIONAL ELECTRICAL CODE

S2898A

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

1. Warranty Claim

You can find the serial number on the rear panel of this unit. In case of warranty claim, please report this number.

2. Recording Copyright

Recording of copyrighted material for other than personal use is illegal without permission of the copyright holder.

3. AC Fuse

The fuse is located inside the chassis and is not user-serviceable. If power does not come on, contact your Onkyo authorized service station.

4. Care

From time to time you should wipe the front and rear panels and the cabinet with a soft cloth. For heavier dirt, dampen a soft cloth in a weak solution of mild detergent and water, wring it out dry, and wipe off the dirt. Following this, dry immediately with a clean cloth. Do not use rough material, thinners, alcohol or other chemical solvents or cloths since these could damage the finish or remove the panel lettering.

5. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY.

The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz) written on the rear panel.

Worldwide models are equipped with a voltage selector to conform to local power supplies. Be sure to set this switch to match the voltage of the power supply in your area before plugging in the unit.

For British models

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel.

IMPORTANT

The wires in the mains lead are coloured in accordance with the following code:

Blue : Neutral

Brown : Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

IMPORTANT

A 5 ampere fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 5 amperes and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMPERE SOCKET. If in any doubt, consult a qualified electrician.

For U.S. models

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC, ANSI/NFPA 70, which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

FCC Information for User

CAUTION:

The user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For Canadian models

NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.

For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH

WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Modele pour les Canadien

REMARQUE: CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CON-FORME À LA NORME NMB-003 DU CANADA.

Sur les modèles dont la fiche est polarisée:

ATTENTION: POUR ÉVITER LES CHOCS

ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE

DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

Declaration of Conformity

We,

ONKYO EUROPE ELECTRONICS GmbH INDUSTRIESTRASSE 20 82110 GERMERING, GERMANY

GERMERING, GERMANY

ONKYO EUROPE ELECTRONICS GmbH

A.HORIUCHI

declare in own responsibility, that the ONKYO product described in this instruction manual is in compliance with the corresponding technical standards such as EN60065, EN55013, EN55020 and EN61000-3-2, -3-3

Features

Supplied accessories

Amplifier Features

• 55 Watts minimum of continuous RMS power to each of the five channels into 8 Ω from 20 Hz to 20 kHz with no more than

0.08% THD (North American models, FTC rated)

• 75 Watts minimum of continuous RMS power to each of the five channels into 6 Ω at 1 kHz (European models, DIN)

• 100 Watts minimum to each of the five channels into 6 Ω at 1 kHz (Asian models, JEITA)

• Wide Range Amplifier Technology (WRAT)

• Extended Frequency Response (20 Hz to 100 kHz)

• Full bandwidth power to all 5 main channels

•

High-current, low-impedance 6-Ohm drive for all five channels

• Oversized electrolytic capacitors

•

State-of-the-art linear PCM 96 kHz/24-bit DACs for all channels

• Fully discrete output stages for all five channels

• Optimum Gain Volume Circuitry

• Massive isolated transformer

• 2 Large high-grade extruded-aluminum heat sinks

• A/B speaker drive

• Tone control (bass, treble) for front L/R speakers

• Auto-protection circuitry

Audio/Video Features

• Dolby∗ Digital, DTS

• All Channel stereo

• 7 DSP soundfields

• High Definition DSP

• Late night mode (on, off)

•“Easy-set” speaker configuration

• Extensive bass management circuitry

• 5.1-Channel input

• Automatic signal detection

• 3 Assignable digital inputs (2 coaxial, 1 optical)

• 3 S-video inputs and 1 output

• 3 A/V inputs

• 3 Audio inputs

• Phono input

• Dedicated line-level subwoofer pre out

• Full input/output cassette and VCR loops

• 7 Sets of heavy-duty multiway speaker binding posts (dual

banana-plug compatible)

∗∗

, Dolby Pro Logic II decoding

FM/AM Tuner Features

• Outstanding selectivity and sensitivity

• 30 FM/AM random presets

• FM auto tuning

• RDS (European models) with PS

• Red FM stereo indicator

• 75-Ohms antenna input

• FM indoor antenna supplied

• AM loop antenna supplied

Other Performance Features

• Precision digital speed-sensitive volume control

• Absolute volume display

•

Separate PC (printed circuit) boards for audio and video sources

• Large bright fluorescent display

• 2-Mode display dimmer (normal, dim)

• Individual input selectors for each source

• Headphone jack (standard size)

• Audio mute (remote controller)

• Sleep timer (remote controller)

• Battery-free memory backup

• 2 Switched AC convenience outlets with a total 120 watts

max. (100 watts max. for European/Asian models)

• Heavy-duty power cord

• Large non-resonant feet

• Heavy-gauge, anti-resonant, reinforced-steel chassis

• Vibration-resistant cover

• Brushed aluminum front panel

• Powerful preprogrammed remote (North American models)

Check that the following accessories are supplied with the TX-DS494.

AM loop antenna × 1

Remote controller × 1

(RC-443S for models other than North American models, RC-444M for North American models)

The following accessories may be available depending on the area which it was purchased.

75/300 Ω antenna adapter × 1

* Manufactured under license from Dolby Laboratories.

**Manufactured under license from Digital Theater Systems, Inc. US Pat.

FM indoor antenna × 1

(Connector will vary depending on model specifications)

Batteries (AA, R6 or UM-3) × 2

Conversion plug × 1

(Use this plug if the power cord plug of the TX-DS494 does not fit your AC outlet. Shape may vary depending on the area which it was purchased.)

Before using this unit

Setting the AM tuning step frequency (Worldwide models only)

Worldwide models are equipped with a switch that controls the AM band tuning steps. Please set this switch to match the AM band tuning step frequency in your area.

U.S.A. and Canada: 10 kHz Other areas: 9 kHz

AM FREQUENCY

STEP

10 k Hz

MONITOR

VIDEO 2

DVD

SUB

ANTENNA

OUT

TAPE

FM 75

DVD

VIDEO 1

GND

PHONO

VIDEO 2

VIDEO

OUT

WOOFER PRE OUT

MONITOR OUT

OUT

VIDEO

DIGITAL INPUT

OPTICAL

COAXIAL

FRONT

SURR

MULTI CHANNEL INPUT

S VIDEO

IN IN

SUB

CENTER

WOOFER

FRONT SPEAKERS

CAUTION: SPEAKER IMPEDANCE

6 OHMS MIN. PER EACH SPEAKER TERMINAL

AV RECEIVER

MODEL NO.

TX-DS494

AC 120

220 -230 V

RATING:

/ 60

Hz 260 W

REMOTE CONTROL

AM FREQUENCY

CENTER SPEAKER

STEP

SURROUND SPEAKERS

AC OUTLETS

SWITCHED

VOLTAGE SELECTOR

220-230 V

TOTAL 100W MAX.

120 V

10 k Hz

Setting the voltage selector (Worldwide models only)

Worldwide models are equipped with a voltage selector to conform with local power supplies. Be sure to set this switch to match the voltage of the power supply in your area before plugging in the unit.

Determine the proper voltage for your area: 220-230 V or 120 V. If the preset voltage is not correct for your area, insert a screwdriver into the groove in the switch. Slide the switch all the way to the right (120 V) or to the left (220-230 V), whichever is appropriate.

3. After batteries are installed and seated correctly, replace the compartment cover.

Notes:

• Do not mix new batteries with old batteries or different kinds of batteries.

• To avoid corrosion, remove the batteries if the remote controller is not to be used for a long time.

• Remove dead batteries immediately to avoid damage from corrosion. If the remote controller does not operate smoothly, replace both batteries at the same time.

• The life of the batteries supplied is about six months but this will vary depending on usage.

Using the remote controller

Point the remote controller toward the remote control sensor. The STANDBY indicator lights up when the unit receives a signal from the remote controller.

Remote control sensor

TX-DS494

MONITOR

VIDEO 2

DVD

SUB

ANTENNA

OUT

TAPE

FM 75

DVD

VIDEO 1

GND

PHONO

VIDEO 2

VIDEO

OUT

WOOFER PRE OUT

MONITOR OUT

OUT

VIDEO

DIGITAL INPUT

OPTICAL

COAXIAL

FRONT

SURR

MULTI CHANNEL INPUT

S VIDEO

IN IN

SUB

CENTER

WOOFER

FRONT SPEAKERS

CAUTION: SPEAKER IMPEDANCE

6 OHMS MIN. PER EACH SPEAKER TERMINAL

AV RECEIVER

MODEL NO. TX-DS494

AC 120

RATING:

/ 60

Hz 260 W

220 -230 V

REMOTE CONTROL

AM FREQUENCY

CENTER SPEAKER

STEP

SURROUND SPEAKERS

AC OUTLETS

SWITCHED

VOLTAGE SELECTOR

220-230 V

TOTAL 100W MAX.

120 V

10 k Hz

VOLTAGE SELECTOR

220-230 V

120 V

Installing batteries into the remote controller

1. Remove the battery compartment cover by pressing and sliding the cover.

2. Insert two AA (R6 or UM-3) batteries into the battery compartment. Carefully follow the polarity diagram (positive (+) and negative (–)

symbols) inside the battery compartment.

STANDBY indicator

30°

Approx. 5 meters (16 feet)

Notes:

• Place the unit away from strong light such as direct sunlight or inverted fluorescent light which can prevent proper operation of the remote controller.

• Using another remote controller of the same type in the same room or using the unit near equipment which uses infrared rays may cause operational interference.

• Do not put objects on the remote controller. Its buttons may be pressed by mistake and drain the batteries.

• Make sure the audio rack doors do not have colored glass. Placing the unit behind such doors may prevent proper remote

controller operation.

• If there is any obstacle between the remote controller and the remote control sensor, the remote controller will not operate.

Front panel facilities

Here is an explanation of the controls and displays on the front panel of the TX-DS494.

12 34 5 6 7 8

STANDBY/ON

STANDBY

POWER

ABSPEAKERS

PHONES

DISPLAY

OFF

AUDIO

SELECTOR

SP SEL TUNING PRESET

DVD

SW MODE

VIDEO

DIGITAL

INPUT

VIDEO

VCR

TAPE

LISTENING MODE

MEMORY

MODE

CLEAR

STEREO

DTS/

SURROUND

PHONO

DSP

DIMMER

BASS

MASTER VOLUME

TREBLE

AV RECEIVER

TX-DS

494

=-09

DIGITAL

SP SEL TUNING PRESET

SW MODE

!@ # $ % ^ &

INPUT

MODE

MEMORY

CLEAR

AB C DEFGH IJ

RDS

Front panel facilities

1 POWER switch

Turns on the main power supply for the TX-DS494. The TX-DS494 enters standby state and the STANDBY indicator lights up. Pressing the switch again to the off position (— OFF) shuts down the main power supply into the TX-DS494.

• Before turning on the power, make sure all cables are properly connected.

• Turning on the TX-DS494 may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the TX-DS494 into a different electrical circuit.

2 STANDBY indicator

Lights when the TX-DS494 is in the standby state and flashes when a signal is received from the remote controller.

3 STANDBY/ON button

When STANDBY/ON button is pressed to ON while the POWER switch is set to ON, the display will light to show the current volume setting for about 5 seconds then show the current sound input source and listening mode. Pressing the button again returns the TX-DS494 to the standby state. This state turns off the display, disables control functions.

5 DISPLAY button

Each time you press the DISPLAY button, the screen changes as follows:

When an input source other than FM or AM is selected:

Press the DISPLAY button once to initiate the program format display. Pressing the button again switches the display to the other display.

Input source + volume

Program format*

Input source + Listening mode

* If the input signal does not have a program format, then this

will be skipped. The format display returns to the previous display after the format display has lasted for about 5 seconds (

When FM or AM is selected as the input source:

4 SPEAKERS A/B buttons

Press to switch the speaker systems in use between A and B. SPEAKERS A:

SPEAKERS A, CENTER SPEAKER, SURROUND SPEAKERS and SUB WOOFER PRE OUT terminals. When the speakers are turned on, the SPEAKERS A indicator lights up.

SPEAKERS B: Select for the speakers connected to the FRONT

SPEAKERS B terminals. When the speakers are turned on, the SPEAKERS B indicator lights up.

Notes:

• Be sure to use SPEAKERS A to listen to the sound through MULTI CHANNEL INPUT port or in any listening mode other than STEREO.

• You cannot select surround mode when you are using SPEAKERS B. If you select SPEAKERS B while surround mode is selected, surround mode will be automatically canceled.

• You cannot use the A and B speakers simultaneously.

Select for the speakers connected to the FRONT

FM/AM frequency + Preset no.

FM/AM + Listening mode

When an RDS station broadcasting PS information is settled as the input source (European models only):

Press the DISPLAY button once to initiate the frequency display. Pressing the button again switches the display to the other display.

Program Service Name + Preset no.

FM frequency + Preset no.*

FM + Listening mode

* The frequency display returns to the previous display after the

frequency display has lasted for about 5 seconds ( ).

6 LISTENING MODE buttons

Press these buttons to select a listening mode for the current input source. STEREO: Select for normal stereo output. j/DTS SURROUND: Select for the DOLBY PRO LOGIC II,

DOLBY DIGITAL, or DTS surround modes.

DSP: Select for the ORCHESTRA, UNPLUGGED, or ALL CH

ST surround modes. During Dolby Digital playback, this button is used to switch the Late Night function between ON and OFF.

Front panel facilities

7 DIMMER button

Press to set the brightness of the front display. The brightness changes to normal and dim.

• The dimmer control for the front display can also be performed by using the remote controller.

8 MASTER VOLUME dial

The MASTER VOLUME dial is used to control the volume level. Turn the dial clockwise to increase the volume level and counterclockwise to decrease it.

9 PHONES jack

This is a standard stereo jack for connecting stereo headphones. The audio for the front right and left speakers are sent to the headphone speakers. When the headphones are plugged in, the listening mode automatically changes to STEREO and sounds are not output from the speakers.

0 AUDIO SELECTOR button

Press to select an audio input signal format other than FM, AM and PHONO. Each time this button is pressed, the setting cycles; “AUTO” → “MULTI CH” → “ANALOG” → “AUTO” (back to the beginning) (refer to page 23).

Input Selector Buttons (DVD, VIDEO 1, VIDEO 2, TAPE, FM, AM, PHONO, and CD)

These buttons are used to select the input source. Pressing and holding the TAPE button for about 2 seconds allows the TAPE and MD sources to be switched.

= BASS and TREBLE control knobs

Boosts or cuts the bass and treble response.

BASS:

TREBLE: Adjusts the treble response from the Front speakers

Adjusts the bass response from the Front speakers and headphones. Turn the knob clockwise to boost the bass response. Turn the knob counterclockwise to cut the bass response.

and headphones. Turn the knob clockwise to boost the treble response. Turn the knob counterclockwise to cut the treble response.

% MEMORY button

This button is used to assign the radio station that is currently tuned in to a preset channel or delete a previously preset station.

^ TUNING ™/£ buttons

Use these buttons to change the tuner frequency. The tuner frequency is displayed in the front display and it can be changed in 50 kHz increments for FM and 10 kHz (or 9 kHz) increments for AM.

When FM is selected, you can hold down one of the TUNING ™/£ buttons and then release it to activate the auto-search feature. It will search for a station in the direction of the button you pressed and stop when it tunes into one.

& PRESET ™/£ buttons

These buttons make it possible to store desired radio stations under the desired preset numbers and recall them with an easy operation.

* Display

ASPEAKERS A/B indicators

Shows the current speaker system in use.

BSLEEP indicator

Lights up when the sleep timer is active.

CSource/Listening mode indicators

One of these indicators lights to show the format of the current source as “PCM DIGITAL”, “Ÿ DIGITAL” or “DTS”. In addition, one of the listening mode indicators “Ÿ PRO LOGIC II”, “DSP” and “STEREO” lights according to the current listening mode.

DMUTING indicator

Flashes when the mute function is active.

EFM STEREO indicator

Lights up when an FM stereo broadcast station is received.

FTUNED indicator

Lights up when a radio station is received.

~ Remote control sensor

This sensor receives the control signals from the remote controller.

! SP SEL button

Press to select the optimum speaker configuration.

@ SW MODE button

Press to select the subwoofer mode.

# DIGITAL INPUT button

When digital components are connected to the DIGITAL INPUT jacks of the TX-DS494, use this button to assign the DIGITAL INPUT jacks to them according to their forms of connection.

$ FM MODE button

Press to switch the reception mode between stereo and monaural. If audio is interrupted or noise interferes with audio during FM stereo broadcasting, press this button to switch to the monaural reception mode.

GMEMORY indicator

Lights up when the MEMORY button is pressed in the radio station preset operation.

HFM MUTE indicator

Lights up to indicate FM muting. It extinguishes when the monaural reception mode is started by pressing the FM MODE button.

IRDS indicator (European models only)

Lights up when a RDS station is received.

JMulti function display

In usual operation, shows the current input source and volume. When the FM or AM input is selected, it shows the frequency and preset number. When the DISPLAY button is pressed, it shows the listening mode and input source format. However, it does not show the source format when the FM or AM source is selected.

Remote controller

RC-443S (For models other than North American models)

1 2

STANDBY/ ON

INPUT SELECTOR

CD TAPE PHONO TUNER

D V D VIDEO 1 VIDEO 2

SUR MODE

SW MODE AUDIO SEL

SLEEP DI MMER DISPLAY

TUNER

PRESET

4 5

STANDBY/ ON

DISC

MODE

DVD CD TAPE

MUTING

TOP MENU

RETURN

TEST TONE

ENTER

CH SEL

VOLUME

SETUP

LEVEL

8 9

For detailed descriptions on the buttons, see “Front panel facilities” on pages 6 through 8.

1 SLEEP button

For setting the sleep time. This button is provided only on the remote controller (refer to page

23).

2 STANDBY/ON button

Turns on the TX-DS494 or put it in standby.

3 INPUT SELECTOR buttons

For selecting the input source.

4 SUR MODE button

Press to select the surround mode.

5 SW MODE button

Press to select the subwoofer mode.

6 DVD/CD/TAPE operation buttons

For operating z-connected Onkyo components connected to the TX-DS494.

When your remote controller is RC-444M, you can operate TV, VCR, satellite tuner and cable TV tuner from other brand than Onkyo by storing the pre-programming code.

For detailed descriptions on the buttons, see “Using remote controller” on page 30 and “Pre-programming remote controller (North American models only)” on page 32.

RC-444M (For North American models)

1 2

4 5

STANDBY/ ON

INPUT SELECTOR

CD TAPE PHONO TUNER

D V D VIDEO 1 VIDEO 2

SUR MODE

SW MODE AUDIO SEL

TV CABLE SATELLITE

STANDBY/ ON

CH TV VOL

DISC

TV/VCR

TOP MENU

ENTER

RETURN

CH SEL

TEST TONE

SLEEP DI MMER DISPLAY

TUNER

PRESET

MODE

VCR

DVD CD TAPE

MUTING

TV VOL

VOLUME

SETUP

LEVEL

8 9

7 TEST TONE/CH SEL/LEVEL 5/∞ buttons

For setting the output levels for each speaker. These buttons are provided only on the remote controller (refer to

page 21).

8 DIMMER button

For adjusting the brightness of the front display.

9 DISPLAY button

For changing the display.

0 TUNER PRESET 5/∞ button

For selecting a tuner preset channel.

- AUDIO SEL button

Press to select an audio input signal format other than FM, AM and PHONO.

= MODE buttons

For selecting the component to be operated by the remote controller.

~ MUTING button

Activates the mute function. This button is provided only on the remote controller (refer to page

23).

! VOLUME 5/∞ button

For adjusting the volume.

Rear panel facilities

Here is an explanation of the terminals found on the rear of the TX-DS494 and how they are used. Before connecting your audio and video components, be sure to read this section carefully and then proceed to the explanations on how to connect each individual component (refer to page 12).

• Be sure to always refer to the instructions that came with the component that you are connecting.

• Do not plug in the power cord until all connections have been made.

• For input jacks, red connectors (marked R) are used for the right channel, white connectors (marked L) are used for the left channel, and yellow connectors (marked VIDEO) are used for video connections.

12 34 5 6

MONITOR

ANTENNA

PHONO

GND

OUT

DIGITAL INPUT

OPTICAL

COAXIAL

FRONT

SURR

CENTER

MULTI CHANNEL INPUT

DVD

SUB WOOFER

SUB WOOFER PRE OUT

OUT

TAPE

DVD

VIDEO 1

VIDEO 2

MONITOR OUT

OUT

VIDEO

VIDEO 2

S VIDEO

FRONT SPEAKERS

MODEL NO.

• Insert all plugs and connectors securely. Improper connections can result in noise, poor performance, or damage to the equipment.

Improper connection

Inserted completely

• Do not bind audio/video connection cables with power cords and speaker cables. Doing so may adversely effect the picture and sound quality.

AV RECEIVER

TX-DS

494

REMOTE CONTROL

CENTER SPEAKER

SURROUND SPEAKERS

AC OUTLETS

AC 120V 60Hz

SWITCHED

TOTAL 120

W 1A MAX.

789 p q

1 ANTENNA

These terminals are for connecting the FM antenna and AM antenna (refer to page 18).

2 GND

Use this GND terminal for connecting the ground (or earth) wire if a turntable is connected. Refer to “Connecting a turntable” on page

13.

3 SUB WOOFER PRE OUT

This terminal is for connecting an active subwoofer.

4 MONITOR OUT

The monitor output includes both RCA type and S video configurations. This output is for connecting television monitors or projectors.

5 VIDEO IN/OUT

There are 3 video inputs (each one includes both RCA type and S video configurations) and 1 RCA type video output. Connect DVD players, LD players, VCRs or other video components to the video inputs.

The video output channel can be used to be connected to video tape recorder for making recordings.

RCA type jack

S Video jack

6 SPEAKERS

Speaker terminals are provided for the front left, front right, center, surround left and surround right speakers. Speaker outputs are compatible with banana plug connectors (other than European models).

Rear panel facilities

COAXIAL

7 AUDIO IN/OUT

These are the analog audio inputs and outputs. There are 6 audio inputs (3 of which are linked to video inputs) and 2 audio outputs (1 of which are linked to a video output). The audio jacks are nominally labeled for turntables, compact disc players, cassette tape decks, and DVD players. To the audio jacks for VIDEO 1 and 2 connect the audio output from LD players, VCRs or other video components. The audio inputs and outputs require RCA type connectors.

RCA type

• When connecting a VCR or other video component, make sure you connect the audio and video leads together (i.e., both to VIDEO 1).

• The PHONO jacks are designed for use with turntables that use moving magnet cartridges.

8 DIGITAL INPUT (OPTICAL/COAXIAL)

These are the digital audio inputs. There are 2 digital inputs with coaxial jacks and 1 with optical jacks. The inputs accept digital audio signals from a compact disc, LD, DVD, or other digital source component.

OPTICAL

COAXIAL

• When using the optical input jack, remove the protective cap and keep it safely. When the jack is not used, replace the protective cap.

• When using an optical input jack, always use an optical fiber cable.

• When using the digital inputs, make sure to also connect the analog connections whenever possible.

Optical fiber cable

Coaxial cable (RCA type)

p z (REMOTE CONTROL)

Connect the Onkyo components that have z connectors such as a CD player, and cassette tape deck using the z cables provided with them. When these components are interconnected, they can be controlled from the remote controller provided with the TX-DS494.

After connecting the z connectors, check the operation of the remote controller buttons for use in controlling other components (refer to page 30).

REMOTE

CONTROL

TX-DS494

z connector

Ex: Onkyo DVD Player

z connector

Ex: Onkyo CD player

Ex: Onkyo cassette

tape deck

• For remote control operation, the audio connection cables must also be connected.

• The RC-443S or RC-444M remote controller does not support turntables.

• If the connected component has two z connectors, you can use either one to connect to the TX-DS494. The other one can be used to daisy chain with another component.

q AC OUTLETS

The TX-DS494 is supplied with AC mains outlets for connecting the power cords from other devices so that their power is supplied through the TX-DS494. By doing this, you can use the STANDBY/ON button on the TX-DS494 to turn on and off the connected devices as well. The shape, number, and total capacity of the AC outlets may differ depending on the area of purchase.

Other components

9 MULTI CHANNEL INPUT

By connecting a DVD player, MPEG decoder, or other component that has a multi channel port, you can playback the audio with 5.1 channel output. So, be sure to prepare a cable that can properly connect the TX-DS494 to the peripheral device.

FRONT

SUB

CENTER

WOOFER

MULTI CHANNEL INPUT

FRONT SPEAKERS

DVD player/MPEG decoder

SURR

OUT

VIDEO

• Connect the video output to one of VIDEO IN connectors (DVD, VIDEO 1 and VIDEO 2).

1. Front right

2. Surround right

3. Center

4. Front left

5. Surround left

6. Subwoofer

7. Video

AC OUTLETS

AC 230-240V 50Hz

SWITCHED

TOTAL 100W MAX.

AC OUTLETS

AC 120V 60Hz

SWITCHED

TOTAL 120W 1A MAX.

etc.

Caution:

Make sure that the total capacity of the other components connected to this unit does not exceed the capacity that is printed on the rear panel (e.g., 120 watts).

+ 25 hidden pages