Onkyo HT-S5700 Owners Manual

5.1ch Home Theater Speaker Package

Speaker terminals

Keyhole slot

Supplied Accessories

HTP-593

Surround Speakers (SKR-590)

D1406-0

* 2 9 4 0 1 8 7 4 *

Part Names

Make sure you have the following accessories.

Front Speakers (SKF-591)

Front speakers

(White)

Speaker cables 10 ft. (3.0 m)

(Red)

Center Speaker (SKC-591N/SKC-591)

(Green)

Center speaker Speaker cable

SKC-591N (North American) SKC-591 (Asian)

4 rubber stoppers*1

Configuration of the rubber stoppers may be different from the figure, such as being 2 sheets instead of 1 sheet, but the total number will be same.

10 ft. (3.0 m)

Surround speakers

(Blue)

Speaker cables 26 ft. (8.0 m)

(Gray)

Powered Subwoofer (SKW-593/SKW-591)

Subwoofer RCA cable

4 floor pads

10 ft. (3.0 m)

Front Speakers (SKF-591)

Center Speaker (SKC-591N/SKC-591)

Speaker terminals

Keyhole slots

Surround Speakers (SKR-590)

Keyhole slot

Speaker terminals

Caution

• The front grilles are not designed to be removed so do not attempt to remove them forcibly, as this will damage them.

Powered Subwoofer (SKW-593/SKW-591)

Rubb

■ Front

Status indicator

Off: Subwoofer in standby mode or

disconnected from power source Blue:Subwoofer on The status indicator lights blue when low frequency sound is being passed through the speaker. The indicator does not light in the normal dialog or high frequency sound.

Note

• The indicator does not indicate that

power supply of the subwoofer has turned on.

With the Auto Standby function, the SKW-593/SKW-591 automatically turns on when an input signal is detected in standby mode. When there’s no input signal for a while, the SKW-593/SKW-591 automatically enters standby mode.

■ Rear

OUTPUT LEVEL control

This control is used to adjust the volume of the subwoofer.

LINE INPUT

This RCA input should be

To AC outlet

Note

• The Auto Standby function turns the subwoofer on when the input signal exceeds a certain level. If the Auto Standby function does not work reliably, try slightly increasing or decreasing the subwoofer output level on your receiver.

connected to the subwoofer pre out on your AV receiver with supplied RCA cable.

Before Using the Home Theater Speaker Package

Using the Rubber Stoppers for a More Stable Platform

We recommend using the supplied rubber stoppers to achieve the best possible sound from your speakers. The rubber stoppers prevent the speakers from moving, providing a more stable platform. Use rubber stoppers for the center speaker.

er stoppers

Bottom of the SKC-591N/SKC-591

Using the Floor Pads for Subwoofer

If the subwoofer is placed on a hard floor (wood, vinyl, tile, etc.) and playback is very loud, the subwoofer’s feet may damage the flooring. To prevent this, place the supplied pads underneath the subwoofer’s feet. The pads also provide a stable base for the subwoofer.

Floor pad

Setting the Subwoofer Level

To set the level of the subwoofer, use the OUTPUT LEVEL control. Set it so that bass sounds are evenly balanced with the treble sounds from the other speakers. Because our ears are less sensitive to very low bass sounds, there’s a temptation to set the level of the subwoofer too high. As a rule of thumb, set the subwoofer level to what you think is the optimal level, and then back it off slightly.

Wall Mounting

To mount the front/surround speakers vertically, use the keyhole slot shown to hang each speaker on a screw that’s securely screwed into the wall.

Keyhole slots for

wall mounting

SKF-591

To mount the center speaker horizontally, use the two keyhole slots shown to hang the speaker on two screws that are securely screwed into the wall.

Keyhole slots for wall mounting

7-7/8" (200 mm)

Tip

• If the center speaker is tilted, loosen the screw on the declined side to move upward so that the speaker could be adjusted vertically.

SKR-590

SKC-591N/ SKC-591

+ 2 hidden pages