Onkyo HT-r591 User Manual

Download

Page 1

Contents

AV RECEIVER

HT-R591

Instruction Manual

Safety Information and Introduction ............2

Table of Contents...........................................5

Connections .................................................11

Turning On & Basic Operations..................19

Advanced Operations ..................................39

Controlling Other Components...................53

Appendix.......................................................59

Speaker Package

Page 2

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to

persons. The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

AVIS

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand,

PORTABLE CART WARNIN

tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

S3125A

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions:

A. When the power-supply cord or plug is damaged, B. If liquid has been spilled, or objects have fallen

into the apparatus,

C. If the apparatus has been exposed to rain or water,

Safety Information and Introduction

D. If the apparatus does not operate normally by

following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation,

E. If the apparatus has been dropped or damaged in

any way, and

F. When the apparatus exhibits a distinct change in

performance this indicates a need for service.

16. Object and Liquid Entry Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus. Don’t put candles or other burning objects on top of this unit.

17. Batteries Always consider the environmental issues and follow local regulations when disposing of batteries.

18. If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is adequate ventilation. Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a flue-like gap for warm air to escape. The temperature protection operates if the apparatus attain an abnormal high temperature. The apparatus cannot operate until it has cooled down.

En-2

Page 3

Precautions

1. Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder.

2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact your Onkyo dealer.

3. Care—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Don’t use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel lettering.

4. Power WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY. AC outlet voltages vary from country to country. Make sure that the voltage in your area meets the voltage requirements printed on the unit’s rear panel (e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).

The power cord plug is used to disconnect this unit from the AC power source. Make sure that the plug is readily operable (easily accessible) at all times.

For models with [POWER] button, or with both [POWER] and [ON/STANDBY] buttons: Pressing the [POWER] button to select OFF mode does not fully disconnect from the mains. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

For models with [ON/STANDBY] button only: Pressing the [ON/STANDBY] button to select Standby mode does not fully disconnect from the mains. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

5. Preventing Hearing Loss Caution

Excessive sound pressure from earphones and headphones can cause hearing loss.

6. Batteries and Heat Exposure Warning

Batteries (battery pack or batteries installed) shall not be exposed to excessive heat as sunshine, fire or the like.

7. Never Touch this Unit with Wet Hands—Never handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by your Onkyo dealer.

8. Handling Notes

• If you need to transport this unit, use the original

packaging to pack it how it was when you originally bought it.

• Do not leave rubber or plastic items on this unit for a

long time, because they may leave marks on the case.

• This unit’s top and rear panels may get warm after

prolonged use. This is normal.

• If you do not use this unit for a long time, it may not

work properly the next time you turn it on, so be sure to use it occasionally.

For U.S. models

FCC Information for User CAUTION:

The user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

Safety Information and Introduction

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For Canadian Models

NOTE: THIS CLASS B DIGITAL APPARATUS

COMPLIES WITH CANADIAN ICES-003. For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Modèle pour les Canadien

REMARQUE: CET APPAREIL NUMÉRIQUE DE LA

CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA.

Sur les modèles dont la fiche est polarisée:

ATTENTION: POUR ÉVITER LES CHOCS

ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

En-3

Page 4

Supplied Accessories

Make sure you have the following accessories:

Indoor FM antenna (➔ page 18)

AM loop antenna (➔ page 18)

Power cord (Brazilian models) (➔ page 18)

Speaker setup microphone (➔ page 27)

Remote controller (RC-799M) and two batteries (AA/R6)

Quick Start Guide

In catalogs and on packaging, the letter at the end of the product name indicates the color. Specifications and operations are the same regardless of color.

■ Installing the batteries

Batteries (AA/R6)

Note

• If the remote controller doesn’t work reliably, try replacing the batteries.

• Don’t mix new and old batteries or different types of batteries.

• If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion.

• Remove expired batteries as soon as possible to prevent damage from leakage or corrosion.

Safety Information and Introduction

■ Aiming the remote controller

To use the remote controller, point it at the AV receiver’s remote control sensor, as shown below.

Remote control sensor

AV receiver

Approx. 16 ft. (5 m)

En-4

Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference.

Page 5

Safety Information and Introduction

Important Safety Instructions ......................................2

Precautions ...................................................................3

Supplied Accessories...................................................4

Table of Contents..........................................................5

Features .........................................................................6

Front & Rear Panels......................................................7

Front Panel..................................................................7

Display ........................................................................8

Rear Panel ..................................................................9

Remote Controller.......................................................10

Controlling the AV Receiver ......................................10

Connections

Connecting the AV Receiver......................................11

Connecting Your Speakers .......................................11

About AV Connections..............................................14

Connecting Components with HDMI .........................15

Connecting Your Components ..................................16

Connecting Onkyo u Components .........................17

Connecting a Recording Component ........................17

Connecting the Antennas..........................................18

Connecting the Power Cord ......................................18

Using Basic Functions ............................................... 27

Using the Automatic Speaker Setup......................... 27

Using the Listening Modes .......................................30

Using the Home Menu .............................................. 35

Using the Sleep Timer ..............................................35

Setting the Display Brightness.................................. 36

Displaying Source Information.................................. 36

Changing the Input Display....................................... 36

Using the Music Optimizer........................................ 37

Muting the AV Receiver ............................................ 37

Using Headphones ...................................................37

Recording .................................................................38

Advanced Operations

On-screen Setup......................................................... 39

Common Procedures in Setup Menu........................ 39

Setup menu items..................................................... 40

HDMI Input................................................................ 41

Component (Component Video Input) ...................... 41

Digital Audio (Digital Audio Input) ............................. 42

Sp Config (Speaker Configuration)........................... 42

Sp Distance (Speaker Distance)............................... 43

Level Cal (Level Calibration)..................................... 44

Audio Adjust.............................................................. 44

Source Setup ............................................................ 46

Hardware ..................................................................48

HDMI Setup ..............................................................49

Using the Audio Settings ..........................................50

Safety Information and Introduction

Appendix

Troubleshooting ......................................................... 59

Connection Tips and Video Signal Path .................. 64

Using an RIHD-compatible TV, Player,

or Recorder .............................................................. 65

About HDMI................................................................. 67

USB Features.............................................................. 68

License and Trademark Information ........................ 69

Specifications ............................................................. 70

To reset the AV receiver to its factory defaults, turn it on and, while holding down VCR/DVR, press

8ON/STANDBY (➔ page 59).

Turning On & Basic Operations

Turning On/Off the AV Receiver ................................19

Turning On ................................................................19

Turning Off ................................................................19

Playback ......................................................................20

Playing the Connected Component ..........................20

Controlling Contents of USB Devices .......................21

Understanding Icons on the Display .........................22

Playing an iPod/iPhone via USB ...............................22

Playing a USB Device ...............................................23

Listening to AM/FM Radio.........................................24

Controlling Other Components

iPod/iPhone Playback via Onkyo Dock ....................53

Using the Onkyo Dock .............................................. 53

Controlling Your iPod/iPhone.................................... 54

Controlling Other Onkyo Components.....................55

Preprogrammed Remote Control Codes ..................55

Entering Remote Control Codes............................... 55

Remote Control Codes for Onkyo Components

Connected via u ..................................................55

Resetting the REMOTE MODE Buttons ...................56

Resetting the Remote Controller ..............................56

Controlling Other Components .................................57

En-5

Page 6

Safety Information and Introduction

Features

Amplifier

• 80 Watts/Channel @ 8 ohms (FTC)

• 130 Watts/Channel @ 6 ohms (IEC)

• 160 Watts/Channel @ 6 ohms (JEITA)

• Optimum Gain Volume Circuitry

• H.C.P.S. (High Current Power Supply) Massive High Power Transformer

Processing

• HDMI (Audio Return Channel, 3D, DeepColor, x.v.Color, Lip Sync, DTS-HD Master Audio, DTS-HD High Resolution Audio, Dolby TrueHD, Dolby Digital Plus, DSD and Multi-CH PCM)

• Dolby Pro Logic IIz

• Non-Scaling Configuration

• A-Form Listening Mode Memory

•Direct Mode

• Music Optimizer for Compressed Digital Music files

• 192 kHz/24-bit D/A Converters

• Powerful and Highly Accurate 32-bit Processing DSP

• Jitter Cleaning Circuit Technology

Connections

• 4 HDMI Inputs and 1 Output

• Onkyo p for System Control

• 4 Digital Inputs (2 Optical/2 Coaxial)

• Component Video Switching (2 Inputs/1 Output)

• (North American and Brazilian models) Banana PlugCompatible Speaker Posts

• Front-Panel USB Input for Memory Devices and

iPod

/iPhone® models

Miscellaneous

• 40 FM/AM Presets

• Audyssey 2EQ

• Audyssey Dynamic EQ

• Audyssey Dynamic Volume listening level and dynamic range

• Crossover Adjustment (40/50/60/70/80/90/100/120/150/200 Hz)

• A/V Sync Control Function (up to 400 ms)

• Auto Standby Function

• On-Screen Display via HDMI

to correct room acoustic problems

for loudness correction

to maintain optimal

En-6

Page 7

Front & Rear Panels

Front Panel

(North American and Brazilian models) (Asian models)

Safety Information and Introduction

a

b c

p

For detailed information, see the pages in parentheses.

a 8ON/STANDBY button (19) b HDMI THRU indicator (49) c SUBWOOFER LEVEL buttons (51) d Remote control sensor (4) e LISTENING MODE buttons (30) f Display (8) g DIMMER button (North American and Brazilian

models) (36)

h MEMORY button (25) i TUNING MODE button (24)

d

qo

e gf h ij k lm n

r s

tu

j DISPLAY button (36) k SETUP button (39) l TUNING q/w, PRESET e/r (24), cursor and

ENTER buttons

m RETURN button n MASTER VOLUME control (20) o MUSIC OPTIMIZER button (37, 52) p PHONES jack (37) q TONE and Tone Level buttons (50) r Input selector buttons (20) s AUX INPUT AUDIO and VIDEO jacks (16)

v

t USB port (16) u SETUP MIC jack (27) v RT/PTY/TP button (Asian models) (25)

En-7

Page 8

Display

Safety Information and Introduction

bca

For detailed information, see the pages in parentheses.

a HDMI indicator (49, 64) b M.Opt indicator (37, 52) c Listening mode and format indicators (30, 48) d Audyssey indicator (27, 46)

Dynamic EQ indicator (46) Dynamic Vol indicator (47)

e Tuning indicators

RDS indicator (excluding North American and Brazilian models) (25)

AUTO indicator (24) TUNED indicator (24) FM STEREO indicator (24)

f SLEEP indicator (35) g MUTING indicator (37) h Message area

En-8

Page 9

Rear Panel

(North American and Asian models) (Brazilian models)

Safety Information and Introduction

a b c

g

a DIGITAL IN COAXIAL and OPTICAL jacks b COMPONENT VIDEO IN and OUT jacks c HDMI IN and OUT jacks d FM ANTENNA jack and AM ANTENNA terminal e SUBWOOFER PRE OUT jack f Power cord (North American and Asian models) g uREMOTE CONTROL jack h Composite video and analog audio jacks

(BD/DVD IN, VCR/DVR IN and OUT, CBL/SAT IN, GAME IN, TV/CD IN)

h i

d

e

f

j

i MONITOR OUT V jack j SPEAKERS terminals

(FRONT, CENTER, SURROUND, SURROUND BACK or FRONT HIGH)

k AC INLET (Brazilian models)

See “Connecting the AV Receiver” for connection (➔ pages 11 to 18).

k

En-9

Page 10

Remote Controller

Controlling the AV Receiver

a b

k l

To control the AV receiver, press RECEIVER to select Receiver mode. You can also use the remote controller to control Onkyo Blu-ray Disc/DVD player, CD player, and other components. See “Entering Remote Control Codes” for more details (➔ page 55).

For detailed information, see the pages in parentheses.

a 8 button (19) b REMOTE MODE/INPUT SELECTOR buttons (20) c TONE and Tone Level buttons (50) d q/w/e/r and ENTER buttons e SETUP button (39) f Listening Mode buttons (30) g DIMMER button (36) h DISPLAY button (36) i MUTING button (37) j VOL q/w button (20) k RETURN button l HOME button (35) m SLEEP button (35)

Safety Information and Introduction

■ Controlling the tuner

To control the AV receiver’s tuner, press AM or FM (or RECEIVER).

a q/w buttons (24) b D.TUN button (24) c DISPLAY button d CH +/– button (25) e Number buttons (24)

SP A/B is not used for this model.

En-10

Page 11

Connections

Connecting the AV Receiver

Connecting Your Speakers

Connecting the Speaker Cables

The following illustration shows how to connect the speakers to each pair of terminals. If you’re using only one surround back speaker, connect it to the SURROUND

BACK or FRONT HIGH L terminals.

Tip

• You can specify whether surround back or front high speakers are connected in the “Sp Config (Speaker Configuration)” menu (➔ page 42) or during Audyssey 2EQ Speaker Setup (➔ page 27).

■ Screw-type speaker terminals

Strip 1/2" to 5/8" (12 to 15 mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown (Supplied speaker cables are already stripped).

1/2" to 5/8" (12 to 15 mm)

Room Correction and

Surround back/

front high

right

Surround back/

front high

left

Surround

right

Surround

left

Front right Front left

Center

■ Banana Plugs (North American and Brazilian

models)

• If you are using banana plugs, tighten the speaker terminal before inserting the banana plug.

• Do not insert the speaker code directly into the center hole of the speaker terminal.

En-11

Page 12

Speaker Configuration

The following table indicates the channels you should use depending on the number of speakers that you have. No matter how many speakers you use, a powered subwoofer is recommended for a really powerful and solid bass. To get the best from your surround sound system, you need to set the speaker settings automatically (➔ page 27) or manually (➔ page 42).

Number of speakers 2 3 4 5 6 7 7

Front speakers ✔✔✔✔✔✔✔ Center speaker ✔✔✔✔✔ Surround speakers ✔✔✔✔✔ Surround back speaker Surround back speakers Front high speakers

If you’re using only one surround back speaker, connect it to the SURROUND BACK or FRONT HIGH L terminals.

Front high and surround back speakers cannot be used at the same time.

*1*2

✔

Connecting the Speaker Cables

Speaker Connection Precautions

Read the following before connecting your speakers:

• You can connect speakers with an impedance of between 6 and 16 ohms. If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in amp protection circuit may be activated.

• Disconnect the power cord from the wall outlet before making any connections.

• Read the instructions supplied with your speakers.

• Pay close attention to speaker wiring polarity. In other words, connect positive (+) terminals only to positive (+) terminals, and negative (–) terminals only to negative (–) terminals. If you get them the wrong way around, the sound will be out of phase and will sound unnatural.

• Unnecessarily long, or very thin speaker cables may affect the sound quality and should be avoided.

• Be careful not to short the positive and negative wires. Doing so may damage the AV receiver.

• Make sure the metal core of the wire does not have contact with the AV receiver’s rear panel. Doing so may damage the AV receiver.

Connections

• Don’t connect more than one cable to each speaker terminal. Doing so may damage the AV receiver.

• Don’t connect one speaker to several terminals.

The speaker terminals are color-coded for identification purpose.

Speaker Color

Front left White Front right Red Center Green Surround left Blue Surround right Gray Surround back left, Front high left Brown Surround back right, Front high right Tan

En-12

Page 13

Using a Powered Subwoofer

LINE INPUT

Powered subwoofer

Corner position

1/3 of wall

position

To find the best position for your subwoofer, while playing a movie or some music with good bass, experiment by placing your subwoofer at various positions within the room, and choose the one that provides the most satisfying results.

Tip

• If your subwoofer is unpowered and you’re using an external amplifier, connect the subwoofer pre out jack to an input on the amplifier.

Connections

En-13

Page 14

About AV Connections

Connecting AV components

HDMI cable

TV, projector, etc.

: Video & Audio

AV Cables and Jacks

■ HDMI

HDMI connections can carry digital video and audio.

Connections

■ Optical digital audio

Optical digital connections allow you to enjoy digital sound such as PCM

, Dolby Digital or DTS. The audio

quality is the same as coaxial.

AV receiver

Blu-ray Disc/

DVD player

Other cables

TV, projector, etc.

Blu-ray Disc/

DVD player

Game console

: Video : Audio

AV receiver

Game console

• Before making any AV connections, read the manuals supplied with your AV components.

• Don’t connect the power cord until you’ve completed and double-checked all AV connections.

• Push plugs in all the way to make

Right!

good connections (loose connections can cause noise or malfunctions).

• To prevent interference, keep audio and video cables away from power

Wrong!

cords and speaker cables.

■ Component video

Component video separates the luminance (Y) and color difference signals (PB, PR), providing the best picture quality (some TV manufacturers label their component video sockets slightly differently).

Green

Blue

Red

■ Composite video

Composite video is commonly used on TVs, VCRs, and other video equipment.

Yellow

■ Coaxial digital audio

Coaxial digital connections allow you to enjoy digital

sound such as PCM

, Dolby Digital or DTS. The audio

quality is the same as optical.

Orange

■ Analog audio (RCA)

Analog audio connections (RCA) carry analog audio.

White

Red

For PCM signals, the supported sampling rates are 32/44.1/48/88.2/96 kHz. With HDMI connections, 176.4 and 192 kHz are also supported.

Note

• The AV receiver does not support SCART plugs.

• The AV receiver’s optical digital jacks have shutter-type covers that open when an optical plug is inserted and close when it’s removed. Push plugs in all the way.

Caution

• To prevent shutter damage, hold the optical plug straight when inserting and removing.

En-14

Page 15

Connecting Components with HDMI

VCR or DVD recorder/digital video recorder

Connections

Game console

Satellite/cable set-top box, etc. Blu-ray Disc/DVD player

If your TV doesn’t support Audio Return Channel (ARC), you need to connect an optical digital cable together with the HDMI cable to the AV receiver.

When listening to an HDMI component through the AV receiver, set the HDMI component so that its video can be seen on the TV screen (on the TV, select the input of the HDMI component connected to the AV receiver). If the TV power is off or the TV is set to another input source, this may result in no sound from the AV receiver or the sound may be cut off.

Connect your components to the appropriate jacks. The default input assignments are shown below.

✔: Assignment can be changed (➔ page 41).

Jack Components

HDMI IN1 Blu-ray Disc/DVD player ✔ HDMI IN2 VCR or DVD recorder/digital video recorder ✔ HDMI IN3 Satellite/cable set-top box, etc. ✔ HDMI IN4 Game console ✔ HDMI OUT TV, projector, etc.

See also:

• “Connection Tips and Video Signal Path” (➔ page 64)

• “Using an RIHD-compatible TV, Player, or Recorder” (➔ page 65)

• “About HDMI” (➔ page 67)

Tip

• To listen to the audio of a component connected via HDMI through your TV’s speakers, enable “HDMI Through” (➔ page 49) and set the AV receiver to standby mode.

Note

• In the case of Blu-ray Disc/DVD players, if no sound is output despite following the above-mentioned procedure, set your Bluray Disc/DVD player’s HDMI audio settings to PCM.

TV, projector, etc.

■ Audio Return Channel (ARC) function

Audio Return Channel (ARC) function enables an HDMI capable TV to send the audio stream to the HDMI OUT of the AV receiver.

• This function can be used when: – Your TV is ARC capable, and –The TV/CD input selector is selected, and –“HDMI Ctrl (RIHD)” is set to “On” (➔ page 49), and –“Audio Return Ch (ARC)” is set to “Auto” (➔ page 50).

En-15

Page 16

Connections

Connecting Your Components

A CB

EDF

Connect your components to the appropriate jacks. The default input assignments are shown below. See “Connection Tips and Video Signal Path” for more information (➔ page 64).

The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

✔: Assignment can be changed (➔ pages 41, 42).

No. Jack/Port Components

AUX INPUT

VIDEO Camcorder, etc. AUDIO L/R USB, AUX INPUT

VIDEO

USB

DIGITAL IN OPTICAL 1 (GAME) Game console ✔ OPTICAL 2 (TV/CD) TV, CD player ✔ COAXIAL 1 (BD/DVD) Blu-ray Disc/DVD player ✔ COAXIAL 2 (CBL/SAT) Satellite/cable set-top box,

COMPONENT VIDEO IN 1 (BD/DVD) Blu-ray Disc/DVD player,

IN 2 (CBL/SAT) Satellite/cable set-top box,

OUT TV, projector, etc. MONITOR OUT TV, projector, etc. BD/DVD IN Blu-ray Disc/DVD player VCR/DVR IN VCR, DVD recorder/

CBL/SAT IN Satellite/cable set-top box,

GAME IN Game console, RI dock TV/CD IN TV, CD player, cassette

iPod/iPhone (video playback)

iPod/iPhone, MP3 player, USB flash drive

RI dock, etc.

RI dock

RI dock, etc.

digital video recorder, RI dock

etc.

tape deck, MD, CD-R, Turntable

, RI dock

Note

When USB input is selected, you can input video signals from the AUX INPUT VIDEO jack. Video signals input from AUX INPUT VIDEO will be output from the MONITOR OUT jack.

Do not connect the AV receiver’s USB port to a USB port on your computer. Music on your computer cannot be played through the AV receiver in this way.

Connect a turntable (MM) that has a phono preamp built-in. If your turntable (MM) doesn’t have it, you’ll need a commercially available phono preamp. If your turntable has a moving coil (MC) type cartridge, you’ll need a commercially available MC head amp or MC transformer as well as a phono preamp. See your turntable’s manual for details.

• With connection D, you can enjoy Dolby Digital and DTS.

• With connection F, if your Blu-ray Disc/DVD player has both the main stereo and multichannel outputs, be sure to connect to the main stereo.

■ How to record a video source

✔

With the connections described above, you cannot record the videos through the AV receiver. See “Recording” about connections for video recording (➔ page 38).

✔

En-16

Page 17

Connections

Connecting Onkyo u Components

Make sure that each Onkyo component is

connected with an analog audio cable (connection F in the hookup examples) (➔ page 16).

Make the u connection (see the illustration).

If you’re using an RI Dock or cassette tape deck,

change the Input Display (➔ page 36).

With u (Remote Interactive), you can use the following special functions:

■ System On/Auto Power On

When you start playback on a component connected via u while the AV receiver is on standby, the AV

receiver will automatically turn on and select that component as the input source.

■ Direct Change

When playback is started on a component connected via u, the AV receiver automatically selects that

component as the input source.

■ Remote Control

You can use the AV receiver’s remote controller to control your other u-capable Onkyo components,

pointing the remote controller at the AV receiver’s remote control sensor instead of the component. You must enter the appropriate remote control code first (➔ page 55).

L R

ANALOG

e.g., cassette tape deck

RI Dock

Note

•Use only u cables for u connections. u cables are supplied with Onkyo components.

• Some components have two u jacks. You can connect either one to the AV receiver. The other jack is for connecting

additional u-capable components.

• Connect only Onkyo components to u jacks. Connecting other manufacturer’s components may cause a malfunction.

• Some components may not support all u functions. Refer to the manuals supplied with your other Onkyo components.

AUDIO OUT

ANALOG

AUDIO OUT

L R

Connecting a Recording Component

See “Recording” for details on recording (➔ page 38).

AUDI O

VCR, DVD recorder,

cassette tape deck,

CDR, MD recorder, etc.

Note

• The AV receiver must be turned on for recording. Recording is not possible while it’s in standby mode.

• If you want to record directly from your TV or playback VCR to the recording VCR without going through the AV receiver, connect the TV/VCR’s audio and video outputs directly to the recording VCR’s audio and video inputs. See the manuals supplied with your TV and VCR for details.

• Video signals connected to composite video inputs can be recorded only via composite video outputs. For example, if your TV/VCR is connected to a composite video input, the recording VCR must be connected to a composite video output.

• The surround sound and DSP listening modes cannot be recorded.

• Copy-protected Blu-ray Discs and DVDs cannot be recorded.

• Sources connected to a digital input cannot be recorded. Only analog inputs can be recorded.

• DTS signals will be recorded as noise, so don’t attempt analog recording of DTS CDs or LDs.

VIDEO

En-17

Page 18

Connections

Connecting the Antennas

This section explains how to connect the supplied indoor FM antenna and AM loop antenna. The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use

the tuner.

North American and Brazilian models

Push. Insert wire. Release.

Assembling the AM loop antenna

Insert the plug fully into the jack.

Caution

• Be careful not to injure yourself when using thumbtacks.

AM loop antenna (supplied)

Note

• Once your AV receiver is ready for use, you’ll need to tune into a radio station and position the antenna to achieve the best possible reception.

• Keep the AM loop antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.

Tip

• If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead.

• If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM antenna.

Indoor FM antenna (supplied)

Asian models

Insert the plug fully into the jack.

Thumbtacks, etc.

Connecting the Power Cord

(Brazilian models)

Connect the supplied power cord to the AV receiver’s AC INLET.

To AC wall outlet

Plug the power cord into an AC wall outlet.

Note

• Before connecting the power cord, connect all of your speakers and AV components.

• Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit.

• Do not use a power cord other than the one supplied with the AV receiver. The supplied power cord is designed exclusively for use with the AV receiver and should not be used with any other equipment.

• Never disconnect the power cord from the AV receiver while the other end is still plugged into a wall outlet. Doing so may cause an electric shock. Always disconnect the power cord from the wall outlet first, and then the AV receiver.

En-18

Page 19

Turning On & Basic Operations

Turning On/Off the AV Receiver

8ON/STANDBY

8

Turning On

Press 8ON/STANDBY on the front panel.

Press RECEIVER followed by 8 on the remote controller.

The AV receiver comes on, and its display lights.

Turning Off

Press 8ON/STANDBY on the front panel.

Press RECEIVER followed by 8 on the remote controller.

The AV receiver will enter standby mode. To prevent any loud surprises when you turn on the AV receiver, always turn down the volume before you turn it off.

Tip

• For details on power management settings, see “Auto Standby” (➔ page 49).

RECEIVER

En-19

Page 20

Playback

The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

This section describes the procedure for using the remote controller unless otherwise specified.

Playing the Connected Component

■ Operating with the remote controller

INPUT SELECTOR

RECEIVER

VOL q/w

Listening mode buttons

Press RECEIVER followed by an INPUT

SELECTOR button.

Start playback on the source component.

See also:

• “Playing an iPod/iPhone via USB” (➔ page 22)

• “Playing a USB Device” (➔ page 23)

• “Listening to AM/FM Radio” (➔ page 24)

• “iPod/iPhone Playback via Onkyo Dock” (➔ page 53)

• “Controlling Other Onkyo Components” (➔ page 55)

To adjust the volume, use VOL q/w.

Select a listening mode and enjoy!

See also:

• “Using the Listening Modes” (➔ page 30)

Turning On & Basic Operations

■ Operating on the AV receiver

Input selector buttons

MASTER VOLUMELISTENING MODE

Use the input selector buttons to select the input

source.

Start playback on the source component.

To adjust the volume, use the MASTER VOLUME

control.

Select a listening mode and enjoy!

En-20

Page 21

Turning On & Basic Operations

Controlling Contents of USB Devices

Press USB

first.

c d

e f

k l

n o p

TOP MENU

This button displays the top menu for each media or service.

q/w and ENTER

These buttons navigate through the menus.

e/r

This button cycles through pages.

PLAYLIST e/r

In Standard Mode (iPod/iPhone), this button selects playlists.

This button starts playback.

This button selects the beginning of the current song. Pressing this button twice selects the previous song.

This button fast-reverses the current song.

This button pauses playback.

You can toggle between the playback screen and the list screen during playback.

DISPLAY

This button switches between song information.

CH +/–

In Standard Mode (iPod/iPhone), this button selects albums.

RETURN

This button returns to the previous menu.

This button selects the next song.

This button fast-forwards the current song.

This button stops playback.

MODE

You can switch between Extended Mode and Standard Mode during iPod/iPhone playback.

RANDOM

This button performs random playback.

REPEAT

Press this button repeatedly to cycle through the repeat modes.

Tip

• See “Controlling Other Onkyo Components” about the operation of other components (➔ page 55).

Note

• The buttons you can use will differ depending on the devices and media used for playback.

En-21

Page 22

Turning On & Basic Operations

Understanding Icons on the Display

This section describes icons that appear on the AV receiver’s display during media playback.

Icon Description

Folder

Track

Playback

Pause

Fast Forward

Fast Reverse

Artist

Album

Repeat One Track

Repeat Folder (USB Device)

Repeat

Shuffle

Shuffle Album (iPod/iPhone)

Playing an iPod/iPhone via USB

The on-screen menus appear only on a TV that is connected to the HDMI OUT.

This section explains how to play music files on the iPod/iPhone. Compatible iPod/iPhone models Made for: iPod touch (1st, 2nd, 3rd and 4th generation), iPod classic, iPod nano (2nd, 3rd, 4th, 5th and 6th generation), iPhone 4S, iPhone 4, iPhone 3GS, iPhone 3G, iPhone

Press USB to select the “USB” input.

Connect the USB cable that comes with the

iPod/iPhone to the USB port on the front of the AV receiver.

While reading the contents of your iPod/iPhone, the message “Connecting...” appears on the AV receiver’s display. A list of your iPod/iPhone model’s contents appears (Extended Mode).

Use q/w to select a folder, and then press ENTER to

open it.

Tip

• If you want to operate using the iPod/iPhone or the remote controller, press MODE to switch to Standard mode.

• When you disconnect the iPod/iPhone, the AV receiver remembers the current mode. This means that if you disconnect when in Extended Mode, the AV receiver will start in Extended Mode the next time you connect the iPod/iPhone.

• You can also use the q/w, ENTER and TUNING MODE buttons on the front panel. TUNING MODE allows you to switch modes.

• When connecting your iPod/iPhone with a USB cable, we recommend you use an official USB cable from Apple Inc.

Use q/w to select a music file, and press ENTER or

1 to start playback.

Note

• While the message “Connecting...” appears on the AV receiver’s display, do not disconnect the USB cable supplied with your iPod/iPhone or the USB device from the USB port.

• If you connect an iPod or iPhone to the USB port, no sound will be output from the headphones jack.

Extended Mode Control

The content information is displayed (lists are displayed), and you can control the content while looking at the screen. Top screen list: Playlists, Artists, Albums, Genres, Songs, Composers, Shuffle Songs, Now Playing.

Standard Mode Control

The content information is not displayed, but can be operated using the iPod/iPhone or the remote controller.

En-22

Page 23

Playing a USB Device

The on-screen menus appear only on a TV that is connected to the HDMI OUT.

This section explains how to play music files from a USB device (e.g., USB flash drives and MP3 players). See also:

• “USB Features” (➔ page 68).

Press USB to select the “USB” input.

Plug your USB device into the AV receiver’s USB

port.

While reading the contents of your USB device, the message “Connecting...” appears on the AV receiver’s display.

Press ENTER.

A list of the device’s contents appears. To open a folder, use q/w to select it, and then press ENTER.

Use q/w to select a music file, and press ENTER or

1 to start playback.

Turning On & Basic Operations

Note

• While the message “Connecting...” appears on the AV receiver’s display, do not disconnect the USB cable supplied with your iPod/iPhone or the USB device from the USB port.

En-23

Page 24

Listening to AM/FM Radio

This section describes the procedure using the buttons on the front panel unless otherwise specified.

Using the Tuner

With the built-in tuner you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection.

You can also change the frequency steps (➔ page 49).

Press AM or FM to select either “AM” or “FM”.

In this example, FM has been selected.

Band Frequency

Tuning into Radio Stations

■ Auto tuning mode

Press TUNING MODE so that the AUTO indicator

lights on the AV receiver’s display.

Press TUNING q/w.

Searching stops when a station is found. When tuned into a station, the TUNED indicator

lights. When tuned into a stereo FM station, the FM STEREO indicator lights as shown.

FM STEREO

AUTO

TUNED

Turning On & Basic Operations

■ Manual tuning mode

In manual tuning mode, FM stations will be in mono.

Press TUNING MODE so that the AUTO indicator

goes off on the AV receiver’s display.

Press and hold TUNING q/w.

The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time.

■ Tuning into stations by frequency

You can tune into AM and FM stations directly by entering the appropriate frequency.

On the remote controller, press AM or FM to select

“AM” or “FM”, followed by D.TUN.

(Actual display depends on the country.)

Tip

• Tuning into weak FM stereo stations

If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to manual tuning mode and listen to the station in mono.

En-24

(Actual display depends on the country.)

Within 8 seconds, use the number buttons to enter

the frequency of the radio station.

For example, to tune to 87.5 (FM), press 8, 7, 5. If you have entered the wrong number, you can retry after 8 seconds.

Page 25

Presetting AM/FM Stations

You can store a combination of up to 40 of your favorite AM/FM radio stations as presets.

Tune into the AM/FM station that you want to store

as a preset.

See the previous section.

Press MEMORY.

The preset number flashes.

(Actual display depends on the country.)

While the preset number is flashing (about 8

seconds), use PRESET e/r to select a preset from 1 through 40.

Press MEMORY again to store the station or

channel.

The station or channel is stored and the preset number stops flashing. Repeat this procedure for all of your favorite AM/FM radio stations.

■ Selecting Presets

To select a preset, use PRESET e/r on the AV

receiver, or the remote controller’s CH +/–.

Tip

• You can also use the remote controller’s number buttons to select a preset directly.

■ Deleting Presets

Select the preset that you want to delete.

See the previous section.

While holding down MEMORY, press TUNING

MODE.

The preset is deleted and its number disappears from the AV receiver’s display.

Turning On & Basic Operations

Using RDS (excluding North American and Brazilian models)

RDS works only in areas where RDS broadcasts are available.

When tuned into an RDS station, the RDS indicator lights. When the station is broadcasting text information, the text can be displayed.

■ What is RDS?

RDS stands for Radio Data System and is a method of transmitting data in FM radio signals. It was developed by the European Broadcasting Union (EBU) and is available in most European countries. Many FM stations use it these days. In addition to displaying text information, RDS can also help you find radio stations by type (e.g., news, sport, rock, etc.).

The AV receiver supports four types of RDS information:

PS (Program Service)

When tuned to an RDS station that’s broadcasting PS information, the station’s name will be displayed. Pressing DISPLAY will display the frequency for 3 seconds.

RT (Radio Text)

When tuned to an RDS station that’s broadcasting text information, the text will be shown on the AV receiver’s display as described in the next section.

PTY (Program Type)

This allows you to search for RDS radio stations by type (➔ page 26).

TP (Traffic Program)

This allows you to search for RDS radio stations that broadcast traffic information (➔ page 26).

En-25

To be continued

Page 26

Note

• In some cases, the text characters displayed on the AV receiver may not be identical to those broadcast by the radio station. Also, unexpected characters may be displayed when unsupported characters are received. This is not a malfunction.

• If the signal from an RDS station is weak, RDS data may be displayed intermittently or not at all.

■ Displaying Radio Text (RT)

Press RT/PTY/TP once.

The RT information scrolls across the AV receiver’s display.

Note

• The message “Waiting” may appear while the AV receiver waits for the RT information.

• If the message “No Text Data” appears, no RT information is available.

■ Finding Stations by Type (PTY)

You can search for radio stations by type.

Press RT/PTY/TP twice.

The current program type appears on the AV receiver’s display.

Use PRESET e/r to select the type of program

you want.

See the table shown later in this chapter.

To start the search, press ENTER.

The AV receiver searches until it finds a station of the type you specified, at which point it stops briefly before continuing with the search.

When a station you want to listen to is found, press

ENTER.

If no stations are found, the message “Not Found” appears.

■ Listening to Traffic News (TP)

You can search for stations that broadcast traffic news.

Press RT/PTY/TP three times.

If the current radio station is broadcasting TP (Traffic Program), “[TP]” will appear on the AV receiver’s display. If “TP” without square brackets appears, this means that the station is not broadcasting TP.

To locate a station that is broadcasting TP, press

ENTER.

The AV receiver searches until it finds a station that’s broadcasting TP. If no stations are found, the message “Not Found” appears.

Turning On & Basic Operations

RDS program types (PTY)

Type Display

None None News reports News Current affairs Affairs Information Info Sport Sport Education Educate Drama Drama Culture Culture Science and technology Science Varied Varied Pop music Pop M Rock music Rock M Middle of the road music Easy M Light classics Light M Serious classics Classics Other music Other M Weather Weather Finance Finance Children’s programmes Children Social affairs Social Religion Religion Phone in Phone In Travel Travel Leisure Leisure Jazz music Jazz Country music Country National music Nation M Oldies music Oldies Folk music Folk M Documentary Document Alarm test TEST Alarm Alarm!

En-26

Page 27

Turning On & Basic Operations

Using Basic Functions

Using the Automatic Speaker Setup

With the supplied calibrated microphone, Audyssey 2EQ® automatically determines the number of speakers connected, their size for purposes of bass management, optimum crossover frequencies to the subwoofer (if present), and distances from the primary listening position. Audyssey 2EQ then removes the distortion caused by room acoustics by capturing room acoustical problems over the listening area in both the frequency and time domain. The result is clear, well-balanced sound for everyone. Audyssey 2EQ can be used with Audyssey Dynamic EQ and Audyssey Dynamic Volume

(➔ pages 46, 47). Before using this function, connect and position all of your speakers. Audyssey 2EQ offers two ways of measuring: the

“Audyssey Quick Start” and “Audyssey 2EQ Full Calibration”.

•“Audyssey Quick Start” uses the measurement from one

position to perform the speaker setting only.

•“Audyssey 2EQ Full Calibration” uses the

measurement from three positions to correct room

response in addition to the speaker setting. The more positions are used in measuring, the better the listening environment will become. We recommend using

a measurement from three positions to create the best listening environment.

The Quick Start takes 2 minutes and Full Calibration takes about 10 minutes. Total measurement time varies depending on the number of speakers.

Measurement procedure

To create a listening environment in your home theater that all listeners will enjoy, Audyssey 2EQ takes measurements at up to three positions within the listening area. Position the microphone at ear height of a seated listener with the microphone tip pointed directly at the ceiling using a tripod. Do not hold the microphone in your hand during measurements as this will produce inaccurate results.

a First measurement position

Also referred to as the Main Listening Position, this refers to the most central position where one would normally sit within the listening environment. Audyssey 2EQ uses the measurements from this position to calculate speaker distance, level, polarity, and the optimum crossover value for the subwoofer.

b Second measurement position

The right side of the listening area.

c Third measurement position

The left side of the listening area.

The distances from position a to b and a to c must be at least 1 meter (3.3 ft.).

abc

: Listening area

ato c: Listening position

Note

• Make the room as quiet as possible. Background noise and Radio Frequency Interference (RFI) can disrupt the room measurements. Close windows, televisions, radios, air conditioners, fluorescent lights, home appliances, light dimmers, or other devices. Turn off the cell phone (even if it is not in use) or place it away from all audio electronics.

• The microphone picks up test tones played through each speaker as Audyssey 2EQ Room Correction and Speaker Setup runs.

• Audyssey 2EQ Room Correction and Speaker Setup cannot be performed while a pair of headphones is connected.

En-27

Page 28

Turning On & Basic Operations

Turn on the AV receiver and the connected TV.

On the TV, select the input to which the AV receiver is connected.

Set the speaker setup microphone at the Main

Listening Position a, and connect it to the SETUP MIC jack.

SETUP MIC jack

Speaker setup microphone

The speaker setting menu appears.

Note

• The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

When you’ve finished making the settings, press

ENTER.

Audyssey

Perform the

2EQ: Auto Setup

SurrBk/FrontHigh < SurrBack >

“Sp Config (Speaker Configuration)”

according to your speaker configuration:

–“SurrBk/FrontHigh” (➔ page 42)

Use q/w to select “Audyssey Quick Start” or

“Audyssey 2EQ Full Calibration”, and then press ENTER.

Press ENTER.

Audyssey 2EQ

Room Correction and Speaker Setup

starts. Test tones are played through each speaker as

Audyssey 2EQ Room Correction and Speaker Setup runs. This process takes a few minutes. Please refrain from talking during measurements and do not stand between speakers and the microphone. Do not disconnect the speaker setup microphone during Audyssey 2EQ Room Correction and Speaker Setup, unless you want to cancel the setup. If you select “Audyssey Quick Start”, you will go to step 8.

Place the speaker setup microphone at the next

position, and then press ENTER.

Audyssey 2EQ performs more measurements. This takes a few minutes.

When prompted, repeat step 6.

Use q/w to select an option, and then press ENTER.

2EQ: Auto Setup

<- Review Speaker Configuration ->

Subwoofer : Yes Front : Small Center : Small Surround : Small Front High : None Surr Back : Small Surr Back Ch : 2ch Crossover : 100Hz

Save Cancel

Audyssey

The options are:

` Save:

Save the calculated settings and exit Audyssey 2EQ Room Correction and Speaker Setup.

` Cancel:

Cancel Audyssey 2EQ Room Correction and Speaker Setup.

Tip

• You can view the calculated settings for the speaker configuration, speaker distances, and speaker levels by

using e/r.

Use q/w to select a target, and use e/r to change

the setting.

After the results of Audyssey 2EQ have been saved, the menu will display the “Audyssey” (➔ page 46), “Dynamic EQ” (➔ page 46), “Dynamic Volume” (➔ page 47) settings.

Note

• When “Audyssey Quick Start” has been used for measurement, “Audyssey” cannot be selected.

• These settings are applied to all input selectors.

Press ENTER.

Disconnect the speaker setup microphone.

Note

• You can cancel Audyssey 2EQ Room Correction and Speaker Setup at any point in this procedure simply by disconnecting the setup microphone.

• Do not connect or disconnect any speakers during Audyssey 2EQ Room Correction and Speaker Setup.

• If the AV receiver is muted, it will be unmuted automatically when Audyssey 2EQ Room Correction and Speaker Setup starts.

• Changes to the room after Audyssey 2EQ Room Correction and Speaker Setup requires you run Audyssey 2EQ Room Correction and Speaker Setup again, as room EQ characteristics may have changed.

En-28

Page 29

Turning On & Basic Operations

Error Messages

While Audyssey 2EQ® Room Correction and Speaker Setup is in progress, one of the error messages below may appear.

2EQ: Auto Setup

Ambient noise is too high.

Retry Cancel

The options are:

` Retry:

Try again.

` Cancel:

Cancel Audyssey 2EQ Room Correction and Speaker Setup.

• Ambient noise is too high.

The background noise is too loud. Remove the source of the noise and try again.

• Speaker Matching Error!

The number of speakers detected was different from that of the first measurement. Check the speaker connection.

• Writing Error!

This message appears if saving fails. Try saving again. If this message appears after 2 or 3 attempts, contact your Onkyo dealer.

• Speaker Detect Error

This message appears if a speaker is not detected. “No” means that no speaker was detected.

Tip

• See “Speaker Configuration” for appropriate settings (➔ page 12).

Audyssey

Error message

Changing the Speaker Setup Manually

You can manually make changes to the settings found during Audyssey 2EQ Room Correction and Speaker Setup. See also:

• “Sp Config (Speaker Configuration)” (➔ page 42)

• “Sp Distance (Speaker Distance)” (➔ page 43)

• “Level Cal (Level Calibration)” (➔ page 44)

Using a Powered Subwoofer

If you’re using a powered subwoofer and it outputs very low-frequency sound at a low volume level, it may not be detected by Audyssey 2EQ Room Correction and Speaker Setup.

If the “Subwoofer” appears on the “Review Speaker Configuration” screen as “No”, increase the subwoofer’s volume to the half-way point, set it to its highest crossover frequency, and then try running Audyssey 2EQ Room Correction and Speaker Setup again. Note that if the volume is set too high and the sound distorts, detection issues may occur, so use an appropriate volume level. If the subwoofer has a low-pass filter switch, set it to Off or Direct. Refer to your subwoofer’s instruction manual for details.

En-29

Page 30

Using the Listening Modes

Selecting Listening Modes

See “About Listening Modes” for detailed information about the listening modes (➔ page 31).

■ Listening Mode Buttons

Press RECEIVER first.

MOVIE/TV, MUSIC, GAME

Turning On & Basic Operations

MOVIE/TV button

This button selects the listening modes intended for use with movies and TV.

MUSIC button

This button selects the listening modes intended for use with music.

GAME button

This button selects the listening modes intended for use with video games.

STEREO button

This button selects the Stereo listening mode and All Channel Stereo listening mode.

• The Dolby Digital and DTS listening modes can only be selected if your Blu-ray Disc/DVD player is connected to the AV receiver with a digital audio connection (coaxial, optical, or HDMI).

• The listening modes you can select depends on the format of the input signal. To check the format, see “Displaying Source Information” (➔ page 36).

• While a pair of headphones is connected, you can select the following listening modes: Direct, Stereo, and Mono.

• While Speakers A and B are on, you can select only the Direct, Stereo, Mono, or T-D (Theater-Dimensional) listening mode.

MUSIC

MOVIE/TV

GAME STEREO

En-30

Page 31

About Listening Modes

The AV receiver’s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound.

■ Explanatory Notes

ab c d e

a Front speakers b Center speaker c Surround speakers

d Surround back speakers

e Front high speakers f Subwoofer

Input Source

The following audio formats are supported by the listening mode.

A S

This is mono (monophonic) sound. This is stereo (stereophonic) sound. Two

independent audio signal channels are reproduced through two speakers.

This is 5.1-channel surround sound. This surround system has five main channels of sound and a sixth subwoofer channel (called the point-one channel).

This is 7.1-channel surround sound. This is a further sound enhancement to 5.1-channel sound with two additional speakers that provide greater sound envelopment and more accurate positioning of sounds.

This is DTS-ES surround sound. This surround system can produce a discrete or a matrix-encoded sixth channel from existing DTS 5.1 encoded material.

This is Dolby Digital EX surround sound. This provides a center back surround channel from 5.1channel sources.

Turning On & Basic Operations

Speaker Layout

The illustration shows which speakers are activated in each channel. See “Sp Config (Speaker Configuration)” for the speaker setup (➔ page 42).

En-31

Page 32

■ Onkyo-Original DSP Listening Modes

Listening Mode Description Input

Orchestra

Or c e s t rah

Suitable for classical or operatic music, this mode emphasizes the surround channels in order to widen the stereo image, and simulates the natural reverberation of a large hall.

Unplugged

Unp u gg edl

Suitable for acoustic instruments, vocals, and jazz, this mode emphasizes the front stereo image, giving the impression of being right in front of the stage.

Studio-Mix

Stu io– Mi xd

Suitable for rock or pop music, listening to music in this mode creates a lively sound field with a powerful acoustic image, like being at a club or rock concert.

TV Logic

TV og i cL

This mode adds realistic acoustics to TV shows produced in a TV studio, surround effects to the entire sound, and clarity to voices.

Game-RPG

Gam – R P Ge

Game-Action

Gam –A c t i one

Game-Rock

Gam –Ro c ke

Game-Sports

Gam – S p ortse

In this mode, the sound has a dramatic feel with a similar atmosphere to Orchestra mode.

In this mode, sound localization is distinct with emphasis on bass.

In this mode, sound pressure is emphasized to heighten live feel.

In this mode, reverberation is increased and sound localization decreased slightly.

All Ch Stereo Ideal for background music, this mode fills

Al l Ch Stereo

the entire listening area with stereo sound from the front, surround, and surround back speakers.

Full Mono In this mode, all speakers output the same

Fu l Monol

sound in mono, so the sound you hear is the same regardless of where you are within the listening room.

Source

A S D F G H

Speaker Layout

XCN

Turning On & Basic Operations

Listening Mode Description Input

T-D (TheaterDimensional)

T – D

With this mode you can enjoy a virtual surround sound even with only two or three speakers. This works by controlling how sounds reach the listener’s left and right ears. Good results may not be possible if there’s too much reverb, so we recommend that you use this mode in an environment with little or no natural reverb.

Source

A S D F G H

■ Listening Modes

Listening Mode Description Input

Direct In this mode, audio from the input source is

Di rec t

output without surround-sound processing. The speaker configuration (presence of speakers) and speaker distance settings are enabled, but much of the processing set via Home menu is disabled. A/V Sync does not have effect on the analog audio. See “Onscreen Setup” for more details (➔ page 39).

Stereo Sound is output from the front left and right

Stereo

speakers and subwoofer.

Mono Use this mode when watching an old movie

Mono

with a mono soundtrack, or use it with the foreign language soundtracks recorded in the left and right channels of some movies. It can also be used with DVDs or other sources containing multiplexed audio, such as karaoke DVDs.

Multichannel This mode is for use with PCM multichannel

Mu l t i ch

sources.

Source

A S D F G H

D F

Speaker Layout

ZXC N

Speaker Layout

ZXC

ZXC N

XCN

En-32

Page 33

Turning On & Basic Operations

Listening Mode Description Input

Source

DSD

Dolby Digital

Dolby D

Dolby Digital Plus

Dolby D +

Dolby TrueHD

DTS

DTS-HD High Resolution Audio

DTS– HD HR

DTS-HD Master Audio

DTS– HD MS TR

DTS Express

DTS E xp r e s s

DTS 96/24

DTS 96 / 2 4

In this mode, audio from the input source is output without surround-sound processing. The speaker configuration (presence of speakers), crossover frequency, speaker distance, A/V Sync and much of the processing set via Home menu are enabled.

See “On-screen Setup” for more details (➔ page 39).

This mode is for use with DTS 96/24 sources. This is high-resolution DTS with a 96 kHz sampling rate and 24-bit resolution,

D XCN

D XCN FXC

D XCN

D XCN FXC

D XCN

providing superior fidelity. Use it with DVDs that bear the DTS 96/24 logo.

Speaker Layout

Listening Mode Description Input

Source

DTS-ES Discrete

ES i screteD

This mode is for use with DTS-ES Discrete soundtracks, which use a discrete surround back channel for true 6.1/7.1-channel

playback. The seven totally separate audio channels provide better spatial imaging and 360-degree sound localization, perfect for sounds that pan across the surround channels. Use it with DVDs that bear the DTS-ES logo, especially those with a DTSES Discrete soundtrack.

DTS-ES Matrix

ES a t r i xM

This mode is for use with DTS-ES Matrix soundtracks, which use a matrix-encoded back-channel for 6.1/7.1-channel playback. Use it with DVDs that bear the DTS-ES logo, especially those with a DTS-ES Matrix soundtrack.

Dolby Pro Logic IIx Dolby Pro Logic II

Dolby Pro Logic IIx expands any 2-channel source for 7.1-channel playback. It provides a very natural and seamless surround-sound experience that fully envelops the listener. As well as music and movies, video games can also benefit from the dramatic spatial effects and vivid imaging.

PL Mov i e

If you’re not using any surround back speakers, Dolby Pro Logic II will be used

S XCN

instead of Dolby Pro Logic IIx.

PL Mus i c

• Dolby PLIIx Movie

Use this mode with any stereo or Dolby

PL Game

Surround (Pro Logic) movie (e.g., TV, DVD, VHS).

PL x Mov i e

PL x Mus i c

PL x Game

• Dolby PLIIx Music

Use this mode with any stereo or Dolby Surround (Pro Logic) music source (e.g., CD, radio, cassette, TV, VHS, DVD).

•Dolby PLIIx Game

Use this mode with video games, especially those that bear the Dolby Pro Logic II logo.

• Dolby PLIIx Movie

• Dolby PLIIx Music

These modes use the Dolby Pro Logic IIx modes to expand 5.1-channel sources for

7.1-channel playback.

Speaker Layout

En-33

Page 34

Turning On & Basic Operations

Listening Mode Description Input

Source

Dolby Pro Logic IIz Height

PL z He i gh t

Dolby Pro Logic IIz Height is designed to more effectively use existing program material when height channel speaker outputs are present. Dolby Pro Logic IIz

S D F

Height can be used to upmix a variety of sources from movies and music, but are particularly well-suited to upmix game content.

Dolby EX These modes expand 5.1-channel sources for

Dolby EX

Dolby D EX

6.1/7.1-channel playback. They’re especially suited to Dolby EX soundtracks that include a matrix-encoded surround back channel. The additional channel adds an extra

D H

dimension and provides an enveloping surround sound experience, perfect for rotating and fly-by sound effects.

Neo:6 This mode expands any 2-channel source for

up to 7.1-channel playback. It uses seven full-bandwidth channels of matrix decoding for matrix-encoded material, providing a very natural and seamless surround sound experience that fully envelops the listener.

Neo 6:Ne o 6 C i nema:

•Neo:6 Cinema

Use this mode with any stereo movie (e.g.,

S XCN

TV, DVD, VHS).

Neo 6 Music:

•Neo:6 Music

Use this mode with any stereo music source (e.g., CD, radio, cassette, TV, VHS, DVD).

Neo 6:

•Neo:6

This mode uses Neo:6 to expand 5.1-

channel sources for 6.1/7.1-channel playback.

Speaker Layout

Note

These listening modes cannot be selected during USB or iPod playback.

Based on the audio channel signal contained in the source, the corresponding speakers will output the sound.

The AV receiver can input the DSD signal from HDMI IN. Setting the output setting on the player side to PCM might obtain a better sound according to the player. In that case, set the output setting on the player side to PCM.

For the Blu-ray Discs, Dolby Digital is used in a 3.1/5.1-channel speaker system.

DTS is used depending on the configuration of the AV receiver.

If there are no surround back speakers, DTS is used.

If there are no surround back speakers, Dolby Pro Logic II is used.

• The listening modes cannot be selected with some source formats.

En-34

Page 35

Using the Home Menu

The Home menu provides quick access to frequently used settings. You can change settings and view the current information.

The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

Note

• The on-screen menus are displayed when: – There is no video input, or – The video input is 480p, 576p, 720p, 1080i, or 1080p.

Press RECEIVER followed by HOME.

The Home menu will be superimposed on the TV screen.

Use q/w and ENTER to make the desired selection.

■ Input

` You can select the input source.

Use q/w to select the desired input source. Pressing ENTER switches to the selected input source.

■ Audio

` You can change the following settings: “Bass”,

“Treble”, “Subwoofer Level”, “Center Level”, “Audyssey”, “Dynamic EQ”, “Dynamic Volume”, “Late Night”, “Music Optimizer”, and “Cinema Filter”.

See also:

• “Audyssey” (➔ page 46)

• “Using the Audio Settings” (➔ page 50)

■ Info

` You can view the information of the following

items: “Input” and “Output”.

■ Listening Mode

` You can select the listening modes that are

grouped in the following categories: “MOVIE/TV”, “MUSIC” and “GAME”.

Use q/w to select the category and e/r to select the listening mode. Press ENTER to switch to the selected listening mode.

Note

Depending on the input source and listening mode, not all channels shown here output the sound.

• This setting is not available in either of the following cases: –The “Audio TV Out” setting is set to “On” (➔ page 50). –“HDMI Ctrl (RIHD)” is set to “On” (➔ page 49) and

you’re listening through your TV speakers.

Turning On & Basic Operations

Using the Sleep Timer

With the sleep timer, you can set the AV receiver to turn off automatically after a specified period.

Press RECEIVER once followed by SLEEP

repeatedly to select the required sleep time.

The sleep time can be set from 90 to 10 minutes in 10 minute steps.

The SLEEP indicator lights on the AV receiver’s display when the sleep timer has been set. The specified sleep time appears for about 5 seconds, then the previous display reappears.

Tip

• If you need to cancel the sleep timer, press SLEEP repeatedly until the SLEEP indicator goes off.

• To check the time remaining until the AV receiver sleeps, press SLEEP. Note that if you press again on SLEEP as the time being displayed is equal to 10 minutes or less, the sleep timer will go off.

En-35

Page 36

Turning On & Basic Operations

Setting the Display Brightness

You can adjust the brightness of the AV receiver’s display. You can display various information about the current

Press RECEIVER once followed by DIMMER

repeatedly to switch between: normal, dim, or dimmer brightness.

Tip

• (North American and Brazilian models) Alternatively, you can use the AV receiver’s DIMMER.

Displaying Source Information

input source as follows.

Press RECEIVER once followed by DISPLAY

repeatedly to cycle through the available information.

Tip

• Alternatively, you can use the AV receiver’s DISPLAY.

The following information can typically be displayed.

Input source &

volume

Listening mode

Signal format*2 or sampling frequency

When AM or FM radio is used, the band, frequency, and preset number are displayed.

If the input signal is digital, the signal format is displayed. Information is displayed for about three seconds, then the previously displayed information reappears.

Changing the Input Display

When you connect an u-capable Onkyo component, you must configure the input display so that u can work

properly. This setting can be done only from the front panel.

Press TV/CD, GAME or VCR/DVR.

“TV/CD”, “GAME” or “VCR/DVR” appears on the AV receiver’s display.

Press and hold down the same button (about

3 seconds) to change the input display.

Repeat this step to select the desired input display.

■ TV/CD:

Note

•“DOCK” can be selected for the “TV/CD”, “GAME” or “VCR/DVR” input selector, but not at the same time.

• Enter the appropriate remote control code before using the remote controller for the first time (➔ page 55).

TV/CD → DOCK

→

TAPE

GAME ↔ DOCK■ GAME:

VCR/DVR ↔ DOCK■ VCR/DVR:

→

En-36

Page 37

Turning On & Basic Operations

Using the Music Optimizer

The Music Optimizer function enhances the sound quality of compressed music files.

Press MUSIC OPTIMIZER on the front panel.

The M.Opt indicator lights on the AV receiver’s display.

Tip

• Alternatively, you can use the remote controller’s HOME.

• See “Music Optimizer” for more details (➔ page 52).

Muting the AV Receiver

You can temporarily mute the output of the AV receiver.

Press RECEIVER followed by MUTING.

The output is muted and the MUTING indicator flashes on the AV receiver’s display.

Tip

• To unmute, press MUTING again or adjust the volume.

• Muting is automatically cancelled when the AV receiver is set to standby.

Using Headphones

Connect a pair of stereo headphones with a

standard plug (1/4 inch or 6.3 mm) to the PHONES jack.

Note

• Always turn down the volume before connecting your headphones.

• While the headphones plug is inserted in the PHONES jack, the speakers are turned off.

• When you connect a pair of headphones, the listening mode is set to Stereo, unless it’s already set to Stereo, Mono, or Direct.

• If you connect an iPod or iPhone to the USB port on the AV receiver, no sound will be output from the headphones jack.

En-37

Page 38

Recording

This section explains how to record the selected input source to a component with recording capability.

AV Recording

Audio sources can be recorded to a recorder (e.g., cassette tape deck, CDR, MD recorder). Video sources can be recorded to a video recorder (e.g., VCR, DVD recorder).

Use the input selector buttons to select the source

that you want to record.

You can watch the source while recording. The AV receiver’s MASTER VOLUME control has no effect on recording.

On your recorder, start recording.

On the source component, start playback.

If you select another input source during recording, that input source will be recorded.

Turning On & Basic Operations

En-38

Page 39

Advanced Operations

On-screen Setup

The setup menus provides a convenient way to change the AV receiver’s various settings. Settings are organized into 10 categories.

The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

This section describes the procedure for using the remote controller unless otherwise specified.

Note

• The on-screen menus are displayed when: – There is no video input, or – The video input is 480p, 576p, 720p, 1080i, or 1080p.

Common Procedures in Setup Menu

Remote indicator

RECEIVER

ENTER

q/w/e/r

SETUP

Press RECEIVER followed by SETUP.

Use q/w to select a menu item, and then press

ENTER.

Use q/w to select a setting target, and use e/r to

change the setting.

Press SETUP to close the menu. Press RETURN to return to the previous menu.

RETURN

Explanatory Notes

b c

a Menu selection b Setting target c Setting options (default setting underlined)

Menu Sp Config

■ Subwoofer

` Yes ` No

1. HDMI Input

2. Component

3. Digital Audio

4. Sp Config

5. Sp Distance

6. Level Cal

7. Audio Adjust

8. Source Setup

9. Hardware

10. HDMI Setup

BD/DVD VCR/DVR CBL/SAT GAME

AUX TUNER TV/CD

Setting target

Note

• This procedure can also be performed on the AV receiver by using SETUP, the cursor buttons, and ENTER.

• During Audyssey 2EQ messages, etc., that are displayed on the TV screen will appear on the AV receiver’s display.

Room Correction and Speaker Setup,

En-39

Page 40

Advanced Operations

Setup menu items

Menu item Setting target

HDMI Input

(➔ page 41)

Component

(➔ page 41)

Digital Audio

(➔ page 42)

Sp Config

(➔ page 42)

BD/DVD

VCR/DVR

CBL/SAT

GAME

AUX

TV/CD

BD/DVD

VCR/DVR

CBL/SAT

GAME

AUX

TV/CD

BD/DVD

VCR/DVR

CBL/SAT

GAME

AUX

TV/CD

Subwoofer

Front

Center

Surround

Front High

Surround Back

Surround Back Ch

Crossover

Double Bass

Menu item Setting target

Sp Distance

(➔ page 43)

Level Cal

(➔ page 44)

Audio Adjust

(➔ page 44)

Source Setup

(➔ page 46)

Unit

Left

Front High Left

Center

Front High Right

Right

Surround Right

Surr Back Right

Surr Back Left

Surround Left

Subwoofer

Left

Front High Left

Center

Front High Right

Right

Surround Right

Surr Back Right

Surr Back Left

Surround Left

Subwoofer

Input Ch (Mux)

Input Ch (Mono)

Panorama

Dimension

Center Width

Height Gain

Dolby EX

Center Image

Listening Angle

Audyssey Dynamic EQ [Reference Level]

Dynamic Volume

A/V Sync

Name Audio Selector [Fixed Mode]

Menu item Setting target

Hardware

(➔ page 48)

HDMI Setup

(➔ page 49)

Volume OSD

Remote ID

AM/FM Freq Step AM Freq Step

Auto Standby

HDMI Ctrl (RIHD)

HDMI Through

Audio TV Out

Audio Return Ch

LipSync

En-40

Page 41

Advanced Operations

HDMI Input

123456

Menu HDMI Input

If you connect a video component to an HDMI input, you must assign that input to an input selector. For example, if you connect your Blu-ray Disc/DVD player to HDMI IN 2, you must assign “HDMI2” to the “BD/DVD” input selector.

Here are the default assignments.

Input selector Default assignment

BD/DVD HDMI1

VCR/DVR HDMI2

CBL/SAT HDMI3

GAME HDMI4

AUX - - - - -

TV/CD -----

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,

TV/CD

` HDMI1, HDMI2, HDMI3, HDMI4:

Select the input to which the component has been connected.

` -----:

Select if you’re not using the HDMI OUT. Each HDMI input cannot be assigned to two input selectors or more. When HDMI1 - HDMI4 have already

been assigned, you must first set any unused input selectors to “-----” or you will be unable to assign HDMI1 - HDMI4 to input selector.

Note

• If no video component is connected to HDMI output (even if the HDMI input is assigned), the AV receiver selects the video source based on the setting of “Component (Component Video Input)”.

• When an HDMI IN is assigned to an input selector as explained here, the same HDMI IN will be set as a priority in the “Digital Audio (Digital Audio Input)” (➔ page 42). In this case, if you want to use the coaxial or optical audio input, make the appropriate selection in the “Audio Selector” setting (➔ page 48).

• Do not assign an HDMI IN to the TV/CD selector while “HDMI Ctrl (RIHD)” is set to “On” (➔ page 49), otherwise appropriate CEC (Consumer Electronics Control) operation will not be guaranteed.

• If you assign “-----” to an input selector that is currently selected in “HDMI Through” (➔ page 49), the “HDMI Through” setting will be automatically switched to “Off”.

•The “TUNER” selector cannot be assigned and is fixed at the “-----” option.

Component (Component Video Input)

123456

Menu Component

If you connect a video component to a component video input, you must assign that input to an input selector. For example, if you connect your Blu-ray Disc/DVD player to COMPONENT VIDEO IN 2, you must assign “IN2” to the “BD/DVD” input selector.

Here are the default assignments.

Input selector Default assignment

BD/DVD IN1

VCR/DVR -----

CBL/SAT IN2

GAME -----

AUX -----

TV/CD -----

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,

TV/CD

` IN1, IN2:

Select the input to which the component has been connected.

` -----:

Select if you’re not using the COMPONENT

VIDEO OUT.

Note

•The “TUNER” selector cannot be assigned and is fixed at the “-----” option.

En-41

Page 42

Digital Audio (Digital Audio Input)

123456

Menu Digital Audio

If you connect a component to a digital audio input, you must assign that input to an input selector. For example, if you connect your CD player to the OPTICAL IN 1, you must assign “OPTICAL1” to the “TV/CD” input selector.

Here are the default assignments.

Input selector Default assignment

BD/DVD COAXIAL1

VCR/DVR - - - - -

CBL/SAT COAXIAL2

GAME OPTICAL1

AUX - - - - -

TV/CD OPTICAL2

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,

TV/CD

` COAXIAL1, COAXIAL2, OPTICAL1,

OPTICAL2:

Select the input to which the component has been connected.

` -----:

Select if the component is connected to an analog audio input.

Note

•When an HDMI IN is assigned to an input selector in “HDMI Input” (➔ page 41), the same HDMI IN will be set as a priority in this assignment. In this case, if you want to use the coaxial or optical audio input, make the appropriate selection in the “Audio Selector” (➔ page 48).

• Supported sampling rates for PCM signals (stereo/mono) from a digital input (optical and coaxial) are 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.

•The “TUNER” selector cannot be assigned and is fixed at the “-----” option.

Sp Config (Speaker Configuration)

123456

Menu Sp Config

Some of the settings in this section are set automatically by Audyssey 2EQ® Room Correction and Speaker Setup (➔ page 27).

Here you can check the settings made by Audyssey 2EQ Room Correction and Speaker Setup, or set them manually, which is useful if you change one of the connected speakers after using Audyssey 2EQ Room Correction and Speaker Setup.

This section explains how to specify which speakers are connected and their sizes.

Cone diameter

For speakers with a cone diameter larger than 6-1/2 inches (16 cm), specify Large (full band). For those with a smaller diameter, specify Small (default crossover 100 Hz). The crossover frequency can be changed in the “Crossover (Crossover Frequency)” (➔ page 43).

Note

• These settings are not available in either of the following cases: – A pair of headphones is connected. –The “Audio TV Out” setting is set to “On” (➔ page 50). –“HDMI Ctrl (RIHD)” is set to “On” (➔ page 49) and you’re

listening through your TV speakers.

Advanced Operations

■ Subwoofer

` Yes ` No

■ Front

` Small ` Large:

Select based on the cone diameter.

Note

• If the “Subwoofer” setting is set to “No”, this setting is fixed to “Large”.

■ Center*1, Surround

` Small ` Large:

Select based on the cone diameter.

` None

■ Front High

*2*3*4

` Small ` Large:

Select based on the cone diameter.

` None

■ Surround Back

*2*3*5

` Small ` Large:

Select based on the cone diameter.

` None

Note

If the “Front” setting is set to “Small”, the “Large” option cannot be selected.

If the “Surround” setting is set to “None”, this setting cannot be selected.

If the “Surround” setting is set to “Small”, the “Large” option cannot be selected.

If the “Surround Back” setting is set to other than “None”, this setting is set to “None”.

If the “Front High” setting is set to other than “None”, this setting is set to “None”.

To be continued

En-42

Page 43

■ Surround Back Ch

` 1ch:

Select if only one surround back speaker is connected.

` 2ch

: Select if two (left and right) surround back speakers are connected.

Note

• If the “Surround Back” setting is set to “None”, this setting cannot be selected.

■ Crossover (Crossover Frequency)

This setting is advantageous for the speakers that you specified as “Small” in the “Sp Config (Speaker Configuration)” (➔ page 42). To get the best bass performance from your speaker system, you need to set the crossover frequency according to the size and frequency response of your speakers.

` 40Hz, 50Hz, 60Hz, 70Hz, 80Hz, 90Hz, 100Hz,

120Hz, 150Hz, 200Hz Use the diameter of the smallest speaker in your system when choosing the crossover frequency.

Speaker cone diameter Crossover frequency

Over 8 in. (20 cm) 6-1/2 to 8 in. (16 to 20 cm) 5-1/4 to 6-1/2 in. (13 to 16 cm) 100 Hz 3-1/2 to 5-1/4 in. (9 to 13 cm) 120 Hz Under 3-1/2 in. (9 cm)

Choose the setting suitable for the speaker.

Note

• For a more accurate setting, look up the frequency response in the manuals supplied with your speakers and set accordingly.

• Choose a higher crossover frequency if you want more sound from your subwoofer.

40/50/60 Hz 70/80/90 Hz

150/200 Hz

■ Double Bass

This setting is NOT set automatically by Audyssey 2EQ® Room Correction and Speaker Setup (➔ page 27).

` On ` Off

Turn this setting on to boost bass output by feeding bass sounds from the front left, right, and center channels to the subwoofer.

Note

• When the “Subwoofer” setting is set to “No” or the “Front” setting to “Small”, this setting is fixed to “Off” (➔ page 42).

• This setting is set to “On” automatically when the “Subwoofer” and “Front” settings are set for the first time to “Yes” and “Large” respectively.

Advanced Operations

Sp Distance (Speaker Distance)

123456

Menu Sp Distance

This setting is set automatically by Audyssey 2EQ Room Correction and Speaker Setup (➔ page 27).

Here you can specify the distance from each speaker to the listening position so that the sound from each speaker arrives at the listener’s ears as the sound designer intended.

Note

listening through your TV speakers.

■ Unit

` feet:

Distances can be set in feet. Range: 1ft to 30ft in 1 foot steps.

` meters:

Distances can be set in meters. Range: 0.3m to 9.0m in 0.3 meter steps.

(The default setting varies from country to country.)

■ Left, Front High Left, Center, Front High Right,

Right, Surround Right, Surr Back Right, Surr Back Left, Surround Left, Subwoofer

` Specify the distance from the each speaker to your

listening position.

Note

• Speakers that you set to “No” or “None” in the “Sp Config (Speaker Configuration)” (➔ page 42) cannot be selected.

En-43

Page 44

Advanced Operations

Level Cal (Level Calibration)

123456

Menu Level Cal

This setting is set automatically by Audyssey 2EQ® Room Correction and Speaker Setup (➔ page 27).

Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position.

Note

• These settings cannot be calibrated in either of the following cases: – A pair of headphones is connected. –The “Audio TV Out” setting is set to “On” (➔ page 50). –“HDMI Ctrl (RIHD)” is set to “On” (➔ page 49) and you’re

listening through your TV speakers.

– The AV receiver is muted.

■ Left, Front High Left, Center*1, Front High Right,

Right, Surround Right, Surr Back Right, Surr Back Left, Surround Left

` –12 dB to 0dB to +12 dB in 1 dB step.

■ Subwoofer

` –15 dB to 0dB to +12 dB in 1 dB step.

Note

• Speakers that you set to “No” or “None” in the “Sp Config (Speaker Configuration)” (➔ page 42) cannot be selected.

For the center speaker and subwoofer, the level settings made by using the Home menu are saved in this menu (➔ page 51).

Tip

• If you’re using a handheld sound level meter, adjust the level of each speaker so that it reads 75 dB SPL at the listening position, measured with C-weighting and slow reading.

Audio Adjust

123456

Menu Audio Adjust

With the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like.

Multiplex/Mono

■ Multiplex

Input Ch (Mux)

` Main ` Sub ` Main/Sub

This setting determines which channel of a stereo multiplex source is output. Use it to select audio channels or languages with multiplex sources, multilingual TV broadcasts, and so on.

■ Mono

Input Ch (Mono)

` Left + Right ` Left ` Right

This setting specifies the channel to be used for playing any 2-channel digital source such as Dolby Digital, or 2channel analog/PCM source in the Mono listening mode.

Dolby

■ PL IIx Music (2ch Input)

These settings apply to only 2-channel stereo sources. If you’re not using any surround back speakers, these

settings apply to Dolby Pro Logic II, not Dolby Pro Logic IIx.

Panorama

` On ` Off

With this setting, you can broaden the width of the front stereo image when using the Dolby Pro Logic IIx Music listening mode.

Dimension

` –3 to 0

With this setting, you can move the sound field forward or backward when using the Dolby Pro Logic IIx Music listening mode. Higher settings move the sound field backward. Lower settings move it forward.

If the stereo image feels too wide, or there’s too much surround sound, move the sound field forward to improve the balance. Conversely, if the stereo image feels like it’s in mono, or there’s not enough surround sound, move it backward.

Center Width

` 0 to 3

With this setting, you can adjust the width of the sound from the center speaker when using the Dolby Pro Logic IIx Music listening mode. Normally, if you’re using a center speaker, the center channel sound is output from only the center speaker. (If you’re not using a center speaker, the center channel sound will be distributed to the front left and right speakers to create a phantom center). This setting controls the front left, right, and center mix, allowing you to adjust the weight of the center channel sound.

to +3

to 7

En-44

To be continued

Page 45

■ PL IIz Height Gain

` Low ` Mid ` High

The Height Gain Control in Dolby Pro Logic IIz enables the listener to select how much gain is applied to the front high speakers. There are three settings, “Low”, “Mid” and “High”, and the front high speakers are accentuated in that order. While “Mid” is the default listening setting, the listener may adjust the Height Gain Control to their personal preference.

Note

• If the “Front High” setting is set to “None” (➔ page 42), this setting cannot be selected.

■ Dolby EX

` Auto:

If the source signal contains a Dolby EX flag, the Dolby EX listening mode is used.

` Manual

You can select any available listening mode.

This setting determines how Dolby EX encoded signals are handled. This setting is unavailable if no surround back speakers are connected. This setting is effective with Dolby Digital, Dolby Digital Plus and Dolby TrueHD only.

Note

• If the “Surround Back” setting is set to “None” (➔ page 42), this setting cannot be selected.

• If the “Front High” setting is enabled (➔ page 42), this setting is fixed to “Manual”.

DTS

■ Neo:6 Music

Center Image

` 0 to 2

to 5

The DTS Neo:6 Music listening mode creates 6-channel surround sound from 2-channel stereo sources. With this setting, you can specify by how much the front left and right channel output is attenuated in order to create the center channel.

Changing the value from “0” to “5” will spread the sound of the center channel to left and right (outwards).

Theater-Dimensional

■ Listening Angle

` Wide

Select if the listening angle is 40 degrees.

` Narrow:

Select if the listening angle is 20 degrees.

With this setting, you can optimize the TheaterDimensional listening mode by specifying the angle of the front left and right speakers relative to the listening position. Ideally, the front left and right speakers should be equidistant from the listening position and at an angle close to one of the two available settings.

Front left speaker Front right speaker

20°/40°

Advanced Operations

En-45

Page 46

Source Setup

123456

Items can be set individually for each input selector.

Preparation

Press the input selector buttons to select an input source.

Menu Source Setup

Audyssey

The tone for each speaker is set automatically by Audyssey 2EQ® Room Correction and Speaker Setup. To enable the following settings, you must first perform the Room Correction and Speaker Setup (➔ page 27).

• These technologies cannot be used when: – A pair of headphones is connected, or – Direct listening mode is selected, or –The USB input selector is selected.

■ Audyssey

` Off ` Movie:

Select this setting for movie material. The Audyssey indicator lights.

` Music:

Select this setting for music material. The Audyssey indicator lights.

Note

•When “Audyssey Quick Start” has been used for measurement, the “Audyssey” cannot be selected.

• Audyssey equalizing does not work for DSD sources.

■ Dynamic EQ

` Off ` On:

Audyssey Dynamic EQ® becomes active.

The Dynamic EQ indicator lights. With Audyssey Dynamic EQ, you can enjoy great sound even when listening at low volume levels. Audyssey Dynamic EQ solves the problem of deteriorating

sound quality as volume is decreased by taking into account human perception and room acoustics. It does so by selecting the correct frequency response and surround volume levels moment-by-moment so that the content sounds the way it was created at any volume level — not just at reference level.

Advanced Operations

■ Reference Level

Audyssey Dynamic EQ Reference Level Offset

` 0dB:

This should be selected for movie contents.

` 5dB:

Select this setting for content that has a very wide dynamic range, such as classical music.

` 10 dB:

Select this setting for jazz or other music that has a wider dynamic range. This setting should also be selected for TV content as that is usually mixed at 10 dB below film reference.

` 15 dB:

Select this setting for pop/rock music or other program material that is mixed at very high listening levels and has a compressed dynamic range.

Movies are mixed in rooms calibrated for film reference. To achieve the same reference level in a home theater system each speaker level must be adjusted so that –30 dBFS band-limited (500 Hz to 2000 Hz) pink noise produces 75 dB sound pressure level at the listening position. A home theater system automatically calibrated by Audyssey 2EQ will play at reference level when the master volume control is set to the 0 dB position. At that level you can hear the mix as the mixers heard it.

Audyssey Dynamic EQ is referenced to the standard film mix level. It makes adjustments to maintain the reference response and surround envelopment when the volume is turned down from 0 dB. However, film reference level is not always used in music or other non-film content. Audyssey Dynamic EQ Reference Level Offset provides three offsets from the film level reference (5 dB, 10 dB, and 15 dB) that can be selected when the mix level of the content is not within the standard.

Note

• If “Dynamic EQ” setting is set to “Off”, this technology cannot be used.

En-46

To be continued

Page 47

■ Dynamic Volume

` Off ` Light:

Activates Light Compression Mode.

` Medium:

Activates Medium Compression Mode.

` Heavy:

Activates Heavy Compression Mode. This setting affects volume the most. It quiets the loud parts, such as explosions, and boosts the quiet parts so they can be heard.

Note

• If you make Dynamic Volume active, “Dynamic EQ” is set to “On”. The Dynamic Vol indicator lights.

•When “Dynamic EQ” is set to “Off”, “Dynamic Volume” is automatically switched to “Off”.

Advanced Operations

About Audyssey Dynamic EQ

Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Dynamic EQ selects the correct frequency response and surround levels moment-by-moment at any user-selected volume setting. The result is bass response, tonal balance and surround impression that remain constant despite changes in volume.

Dynamic EQ combines information from incoming source levels with actual output sound levels in the

A/V Sync

■ A/V Sync

` 0ms

to 400 ms in 10 msec steps

When using progressive scanning on your Blu-ray Disc/DVD player, you may find that the picture and sound are out of sync. With this setting, you can correct this by delaying the audio signals.

To view the TV picture while setting the delay, press ENTER.

To return to the previous screen, press RETURN.

room, a prerequisite for delivering a loudness correction solution. Audyssey Dynamic EQ works in tandem with

Audyssey 2EQ every listener at any volume level.

About Audyssey Dynamic Volume

to provide well-balanced sound for

Audyssey Dynamic Volume solves the problem of large

The range of values you can adjust will depend on whether your TV supports HDMI Lip Sync and if the “LipSync” setting is set to “On” or not (➔ page 50).

Note

• A/V Sync is disabled when the Direct listening mode is used with an analog input source.

variations in volume level between television programs, commercials, and between the soft and loud passages of

Preset Name For Input Selector

movies. Dynamic Volume looks at the preferred volume setting by the user and then monitors how the volume of program material is being perceived by listeners in real time to decide whether an adjustment is needed. Whenever necessary, Dynamic Volume makes the necessary rapid or gradual adjustments to maintain the desired playback volume level while optimizing the dynamic range. Audyssey Dynamic EQ is integrated into Dynamic Volume so that as the playback volume is adjusted automatically, the perceived bass response, tonal balance, surround impression and dialog clarity remain the same whether watching movies, flipping between television channels or changing from stereo to surround sound content.

■ Name

` ---

, Blu-ray, DVD, HD DVD, VCR, DVR, Tivo, CableSTB, SAT STB, PS3, Wii, Xbox, PC, TV, CD, TAPE, iPod:

To reset to the default, select “---”. You can enter a preset name for each individual input selector for easy identification. When entered, the preset

name will be displayed.

Note

• You can’t assign the same preset name to multiple input selectors.

• This setting cannot be used for the AM, FM or USB input

selector.

En-47

Page 48

Audio Selector

■ Audio Selector

` ARC:

The audio signal from your TV tuner can be sent to the HDMI OUT of the AV receiver. With this selection, the TV’s audio can be automatically selected as a priority among other assignments.

` HDMI:

This can be selected when HDMI IN has been assigned as an input source. If both HDMI (HDMI

IN) and digital audio inputs (COAXIAL IN or OPTICAL IN) have been assigned, HDMI input is

automatically selected as a priority.

` COAXIAL:

This can be selected when COAXIAL IN has been assigned as an input source. If both coaxial and HDMI inputs have been assigned, coaxial input is automatically selected as a priority.

` OPTICAL:

This can be selected when OPTICAL IN has been assigned as an input source. If both optical and HDMI inputs have been assigned, optical input is automatically selected as a priority.

` Analog:

The AV receiver always outputs analog signals.

You can set priorities of audio output when there are both digital and analog inputs.

Note

• This setting can be made only for the input source that is assigned as HDMI IN, COAXIAL IN, or OPTICAL IN.

You can select “ARC” if you select the TV/CD input selector. But you cannot if you’ve selected “Off” in the “Audio Return Ch” setting (➔ page 50).

Setting the Incoming Digital Signal (Fixed Mode)

■ Fixed Mode

` Off

: The format is detected automatically. If no digital input signal is present, the corresponding analog input is used instead.

` PCM:

Only 2-channel PCM format input signals will be heard. If the input signal is not PCM, the PCM indicator will flash and noise may also be produced.

` DTS:

Only DTS (but not DTS-HD) format input signals will be heard. If the input signal is not DTS, the dts indicator will flash and there will be no sound.

When “HDMI”, “COAXIAL” or “OPTICAL” is selected in the “Audio Selector” setting, you can then specify the signal type in “Fixed Mode”.

Normally, the AV receiver detects the signal format automatically. However, if you experience either of the following issues when playing PCM or DTS material, you can manually set the signal format to PCM or DTS.

• If the beginnings of tracks from a PCM source are cut off, try setting the format to PCM.

• If noise is produced when fast forwarding or reversing a DTS CD, try setting the format to DTS.

Note

• The setting will be reset to “Off” when you change the setting in the “Audio Selector”.

Advanced Operations

Hardware

123456

Menu Hardware

OSD

■ Volume OSD

` On ` Off

Turn this setting on to display the volume level on the TV screen while it is adjusted.

Remote ID

■ Remote ID

` 1

, 2, or 3 When several Onkyo components are used in the same room, their remote ID codes may overlap. To differentiate

the AV receiver from the other components, you can change its remote ID from “1”, to “2” or “3”.

Note

• If you do change the AV receiver’s remote ID, be sure to change

the remote controller to the same ID (see below), otherwise, you won’t be able to control it with the remote controller.

Changing the remote controller’s ID

While holding down RECEIVER, press and hold

down SETUP until the remote indicator lights (about 3 seconds).

Use the number buttons to enter ID 1, 2, or 3.

The remote indicator flashes twice.

En-48

Page 49

Advanced Operations

Tuner

■ AM/FM Freq Step (North American and Brazilian

models)

` 10kHz/200kHz

` 9kHz/50kHz:

Select the frequency step according to your area.

■ AM Freq Step (Asian models)

` 10kHz: ` 9kHz

Select the frequency step according to your area.

For AM/FM tuning to work properly, you must specify the AM/FM frequency step used in your area.

Note

• When this setting is changed, all radio presets will be deleted.

Auto Standby

■ Auto Standby

` Off ` On

When “Auto Standby” is set to “On”, the AV receiver will automatically enter standby mode if there is no operation for 30 minutes with no audio and no video signal input. “Auto Standby” will appear on the AV receiver’s display and OSD 30 seconds before the Auto Standby comes on. Default setting: On (Asian models), Off (North

American and Brazilian models)

Note

On”, the Auto Standby function may activate itself during

•Set to “ playback with some sources.

HDMI Setup

123456

Menu HDMI Setup

■ HDMI Ctrl (RIHD)

` Off ` On

Turn this setting on to allow p-compatible components connected via HDMI to be controlled by the AV receiver (➔ page 65).

Note

• When the setting is set to “On” and the menu is closed, the names of connected p-compatible components and “RIHD On”

are displayed on the AV receiver. “Search…” → “(name)” → “RIHD On” When the AV receiver cannot receive the name of the component, it is displayed as “Player and indicates the number of components, when two or more are received).

• When an p-compatible component is connected to the AV receiver via an HDMI cable, the name of the connected component is displayed on the AV receiver display. For example, while you are watching TV broadcasting, if you operate a Blu-ray Disc/DVD player (being powered on) with the remote control of the AV receiver, the name of the Blu-ray Disc/DVD player will be displayed on the AV receiver.

• Set it to

• If operation is not normal when set to

• Refer to the connected component’s instruction manual for

• When the “HDMI Ctrl (RIHD)” setting is set to “On”, the power

“Off” when a connected piece of equipment is not

compatible or it is unclear whether the equipment is compatible or not.

“Off”.

details.

consumption in standby mode slightly increases. (Depending on the TV status, the AV receiver will enter standby mode as usual.)

” or “Recorder*”, etc (“*” shows up

“On”, change the setting to

• When the source equipment is connected with the u connection, it may malfunction if “HDMI Ctrl (RIHD)” is set to “On”.

■ HDMI Through

` Off ` BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,

TV/CD:

Selects the input source for which the HDMI Through function is enabled.

` Last:

The HDMI Through function is activated on the input source selected at the time of setting the AV receiver to standby mode.

When enabling the HDMI Through function, regardless of whether the AV receiver is on or in standby, both audio and video streams from an HDMI input will be output to the TV or other components via HDMI connection. In standby mode, the HDMI THRU and HDMI indicators will light (HDMI will be dimly-lit).

This setting is fixed to “Auto” automatically when the above “HDMI Ctrl (RIHD)” setting is set to “On”, resulting in automatic input source selection.

Note

• Only the input source assigned to the HDMI IN via “HDMI Input” is enabled (➔ page 41).

• The power consumption in standby mode will increase during the HDMI Through function; however in the following cases, the power consumption can be saved: – The TV is in standby mode. – You are watching a TV program.

• Refer to the connected component’s instruction manual for details.

• Depending on the connected component, the correct input source may not be selected with the setting fixed to “Auto”.

• This setting is set to “Off” automatically when the “HDMI Ctrl (RIHD)” setting is set to “Off”.

En-49

Page 50

■ Audio TV Out

` Off ` On

This preference determines whether the incoming audio signal is output from the HDMI output. You may want to turn this preference on if your TV is connected to the HDMI output and you want to listen to the audio from a connected component through your TV’s speakers. Normally, this should be set to “Off”.

Note

• If “On” is selected and the audio can be output from the TV, the AV receiver will output no sound through its speakers. In this case, “TV Speaker” appears on the AV receiver’s display by pressing DISPLAY.

•When

“HDMI Ctrl (RIHD)” is set to “On”, this setting is fixed

“Auto”.

• With some TVs and input signals, no sound may be output even when this setting is set to

•When “Audio TV Out” or and you’re listening through your TV’s speakers (➔ page 15), turning up the AV receiver’s volume control will make the sound be output from the AV receiver’s front left and right speakers. To stop the AV receiver’s speakers producing sound, change the settings, change your TV’s settings, or turn down the AV receiver’s volume.

• Listening mode cannot be changed when this setting is set to “On” and the input source is not HDMI.

“On”.

“HDMI Ctrl (RIHD)” is set to “On”

■ Audio Return Ch (ARC)

` Off ` Auto:

The audio signal from your TV tuner can be sent to the HDMI OUT of the AV receiver.

The audio return channel (ARC) function allows an ARC capable TV to send the audio stream to the HDMI OUT of the AV receiver. To use this function, you must select the TV/CD input selector and your TV must be ARC capable. Default setting: “

Note

• This setting is fixed to “----” when the “HDMI Ctrl (RIHD)” setting is set to “Off”.

• This setting is set to “Auto” automatically when the “HDMI Ctrl (RIHD)” setting is set to “On” for the first time.

• If you set “Audio Return Ch” to “Auto”, the “Audio Selector” settings of the TV/CD input selector will be automatically switched to “ARC” (➔ page 48).

----”.

■ LipSync

` Off ` On

This function allows the AV receiver to automatically correct any delay between the video and the audio, based on the data from the connected monitor.

Note

• This function works only if your HDMI-compatible TV supports HDMI Lip Sync.

Advanced Operations

Using the Audio Settings

You can change various audio settings from the Home menu (➔ page 35).

Press RECEIVER followed by HOME.

Use q/w and ENTER to select “Audio”, and then

use q/w/e/r to make the desired selection.

Note

• These settings are not available in either of the following cases: –The “Audio TV Out” setting is set to “On”. –“HDMI Ctrl (RIHD)” is set to “On” (➔ page 49) and you’re

listening through your TV speakers.

Tone Control

■ Bass

` –10 dB to 0dB

You can boost or cut low-frequency sounds output from the front speakers.

■ Treble

` –10 dB to 0dB

You can boost or cut high-frequency sounds output

from the front speakers. You can adjust the bass and treble for the front speakers, except when the Direct listening mode is selected.

to +10 dB in 2 dB steps

After changing the settings of the “HDMI Ctrl

”, “HDMI Through” or “Audio Return Ch”

(RIHD)

turn off the power on all connected pieces of equipment and then turn them on again. Refer to the user’s manuals for all connected pieces of equipment.

En-50

Operating on the remote controller directly

Press RECEIVER once followed by TONE

repeatedly to select either “Bass” or “Treble”.

Use – and + to adjust.

Tip

• Alternatively, you can use the AV receiver’s TONE and –/+.

Page 51

Advanced Operations

Speaker Levels

■ Subwoofer Level

` –15 dB to 0dB

■ Center Level

` –12 dB to 0dB to +12 dB in 1 dB steps

You can adjust the volume of each speaker while listening to an input source.

These temporary adjustments are cancelled when the AV receiver is set to standby. To save the setting you made here, go to “Level Cal (Level Calibration)” (➔ page 44) before setting the AV receiver to standby.

Note

• These settings cannot be calibrated in either of the following cases: – A pair of headphones is connected. – The AV receiver is muted.

• Speakers that are set to “No” or “None” in the “Sp Config (Speaker Configuration)” (➔ page 42) cannot be adjusted.

to +12 dB in 1 dB steps

Audyssey

■ Audyssey

See

“Audyssey” in “Source Setup” (➔ page 46).

■ Dynamic EQ

See “Dynamic EQ” in “Source Setup” (➔ page 46).

■ Dynamic Volume

See “Dynamic Volume” in “Source Setup” (➔ page 47).

Note

• These technologies can be used when all the following conditions are met: – Room Correction and Speaker Setup is completed. Note that

“Audyssey” requires the “Audyssey 2EQ Full Calibration”

method. – Any listening mode other than Direct is selected. – A pair of headphones is not connected. – The input selector other than USB is selected.

• The setting is stored individually for each input selector.

Late Night

■ Late Night

For Dolby Digital and Dolby Digital Plus sources, the options are:

` Off ` Low:

Small reduction in dynamic range.

` High:

Large reduction in dynamic range.

For Dolby TrueHD sources, the options are:

` Auto

: The Late Night function is set to “On” or “Off” automatically.

` Off ` On

Turn this setting on to reduce the dynamic range of Dolby Digital material so that you can still hear quiet parts even when listening at low volume levels—ideal for watching movies late at night when you don’t want to disturb anyone.

Note

• The effect of the Late Night function depends on the material that you are playing and the intention of the original sound designer, and with some material there will be little or no effect when you select the different options.

• The Late Night function can be used only when the input source is Dolby Digital, Dolby Digital Plus, or Dolby TrueHD.

• The Late Night function is set to “Off” when the AV receiver is set to standby. For Dolby TrueHD sources, it will be set to “Auto”.

En-51

Page 52

Advanced Operations

Music Optimizer

■ Music Optimizer

` Off ` On

The Music Optimizer function enhances the sound quality of compressed music files. The M.Opt indicator lights on the AV receiver’s display.

Tip

• Alternatively, you can use the AV receiver’s MUSIC OPTIMIZER.

Note

• The Music Optimizer function only works with PCM digital audio input signals with a sampling rate below 48 kHz and analog audio input signals.

• The Music Optimizer is disabled when the Direct listening mode is selected.

• The setting is stored individually for each input selector.

CinemaFILTER

■ Cinema Filter

` Off ` On

Turn this setting on to soften overly bright movie soundtracks, which are typically mixed for reproduction in a movie theater.

CinemaFILTER can be used with the following listening modes: Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Pro Logic IIx Movie, Dolby Pro Logic II Movie, Dolby Pro Logic IIz Height, Multichannel, DTS, DTS-ES, DTS Neo:6 Cinema, DTS 96/24, Neo:6, DTS-HD High Resolution Audio, DTS-HD Master Audio and DTS Express.

Note

• The CinemaFILTER may not work when used with certain input sources.

En-52

Page 53

iPod/iPhone Playback via Onkyo Dock

Using the Onkyo Dock

The Dock is sold separately. Models sold are different depending on the region. For the latest information on the Onkyo Dock components, see the Onkyo web site at: http://www.onkyo.com Before using the Onkyo Dock components, update your iPod/iPhone with the latest software, available from the Apple web site. For supported iPod/iPhone models, see the instruction manual of the Onkyo Dock.

RI Dock

With the RI Dock, you can easily play the music of your iPod/iPhone, or watch the slideshows and videos of your iPod/iPhone on a TV. In addition, the on-screen display (OSD) allows you to view, navigate, and select your iPod/iPhone model’s contents on your TV, and with the supplied remote controller, you can control your iPod/iPhone from the comfort of your sofa. You can even use the AV receiver’s remote controller to operate your iPod/iPhone.

Note

• Enter the appropriate remote control code before using the AV receiver’s remote controller for the first time (➔ page 55).

• Connect the RI Dock to the AV receiver with an u cable (➔ page 17).

• Set the RI Dock’s RI MODE switch to “HDD” or “HDD/DOCK”.

• Set the AV receiver’s Input Display to “DOCK” (➔ page 36).

■ System Function

System On

When you turn on the AV receiver, the RI Dock and iPod/iPhone turn on automatically. In addition, when RI Dock and iPod/iPhone are on, the AV receiver can be

turned on by pressing 8.

Auto Power On

If you press the remote controller’s 1 (Playback) while the AV receiver is on automatically turn on, select your iPod/iPhone as the input source, and your iPod/iPhone will start playback.

Direct Change

If you start iPod/iPhone playback while listening to another input source, the AV receiver will automatically switch to the input to which RI Dock is connected.

Other Remote Operations

You can use the remote controller that came with the AV receiver to control other iPod/iPhone functions. The available functionality depends on the AV receiver.

iPod/iPhone Alarm

If you use the Alarm function on your iPod/iPhone to start playback, the AV receiver will turn on at the specified time and select your iPod/iPhone as the input source automatically.

Note

• Linked operations do not work with video playback or when the alarm is set to play a sound.

• If you use your iPod/iPhone with any other accessories, iPod/iPhone playback detection may not work.

• The System On function may not work depending on the RI Dock.

standby, the AV receiver will

Controlling Other Components

■ Operating Notes

• Use the AV receiver’s volume control to adjust the playback volume.

• While your iPod/iPhone is inserted in the RI Dock, its volume control has no effect.

• If you do adjust the volume control on your iPod/iPhone while it’s inserted in the RI Dock, be careful that it’s not set too loud before you reconnect your headphones.

En-53

Page 54

Controlling Other Components

Controlling Your iPod/iPhone

By pressing the REMOTE MODE button that’s been programmed with the remote control code for your Dock, you can control your iPod/iPhone in the Dock with the buttons described further in this section.

See “Entering Remote Control Codes” for details on entering a remote control code (➔ page 55).

See the Dock’s instruction manual for more information.

RI Dock

• Set the RI Dock’s RI MODE switch to “HDD” or “HDD/DOCK”.

• 8 may not work with a remote control code (without u). In this case, make an u connection and enter the remote control code 81993 (with u).

■ With the RI Control

Make an u connection and enter the remote control code 81993 (with u).

• Set the AV receiver’s Input Display to “DOCK” (➔ page 36).

■ Without the RI Control

You must enter the remote control code 82990 first (➔ page 56).

Press the appropriate REMOTE MODE button first.

b c

g h

■ u Dock operation

Available buttons

a 8

TOP MENU

b c q/w/e/r, ENTER h

PLAYLIST e/r i VOL q/w

d 1, 3, 2, 5, 4,

7, 6

REPEAT

RANDOM

Note

• With some iPod/iPhone models, generations and RI Docks, certain buttons may not work as expected.

• For detailed operation of iPod/iPhone, please refer to the instruction manual of the RI Dock.

This button does not turn the Onkyo DS-A2 or DS-A2X RI Dock on or off. Also, your iPod/iPhone may not respond the first time you press this button, in which case you should press it again. This is because the remote controller transmits the On and Standby commands alternately, so if your iPod/iPhone is already on, it will remain on when the remote controller transmits the On command. Similarly, if your iPod/iPhone is already off, it will remain off when the remote controller transmits the Off command.

TOP MENU works as the mode button when used with the DS-A2 RI Dock.

DISPLAY turns on backlight for a second.

Resume mode

With the Resume function, you can resume playback of the song that was playing when you removed your iPod/iPhone from the RI Dock.

DISPLAY

MUTING

ALBUM +/–

MODE

En-54

Page 55

Controlling Other Components

Controlling Other Onkyo Components

You can use the AV receiver’s remote controller to control your other Onkyo AV components. This section explains how to enter the remote control code for a component that you want to control: DVD, CD, etc.

Preprogrammed Remote Control Codes

The following REMOTE MODE butttons are preprogrammed with remote control codes for controlling the components listed. You do not need to enter a remote control code to control these components.

For details on controlling these components, see the indicated pages.

BD/DVD Onkyo Blu-ray Disc player (➔ page 57) TV/CD Onkyo CD player (➔ page 58)

Entering Remote Control Codes

You’ll need to enter a code for each component that you want to control.

Look up the appropriate remote control code in the

Remote Control Codes for Onkyo Components Connected via u.

While holding down the REMOTE MODE button to

which you want to assign a code, press and hold down DISPLAY (about 3 seconds).

The remote indicator lights.

Note

• Remote control codes cannot be entered for RECEIVER.

• Except for RECEIVER remote control codes from any category can be assigned to the REMOTE MODE button. However, these buttons also work as input selector buttons (➔ page 20), so choose a REMOTE MODE button that corresponds with the input to which you connect your component. For example, if you connect your CD player to the CD input, choose TV/CD when entering its remote control code.

Within 30 seconds, use the number buttons to enter

the 5-digit remote control code.

The remote indicator flashes twice. If the remote control code is not entered successfully,

the remote indicator will flash once slowly.

Remote Control Codes for Onkyo Components Connected via u

Onkyo components that are connected via u are controlled by pointing the remote controller at the AV receiver, not the component. This allows you to control components that are out of view, in a rack, for example.

Make sure the Onkyo component is connected with

an u cable and an analog audio cable (RCA).

See “Connecting Onkyo u Components” for details (➔ page 17).

Enter the appropriate remote control code for a

REMOTE MODE button, by referring to the previous section.

` 42157:

Onkyo cassette tape deck with u

` 81993:

Onkyo Dock with u

Press the REMOTE MODE button, point the

remote controller at the AV receiver, and operate the component.

To be continued

En-55

Page 56

Controlling Other Components

Controlling Onkyo components without u

If you want to control an Onkyo component by pointing the remote controller directly at it, or you want to control an

Onkyo component that’s not connected via u, use the following remote control codes:

` 30627:

Onkyo DVD player without u

` 71817:

Onkyo CD player without u

` 32900/33000:

Onkyo Blu-ray Disc player

` 32901/33004:

Onkyo HD DVD player

` 70868:

Onkyo MD recorder without u

` 71323:

Onkyo CD recorder without u

` 82990:

Onkyo Dock without u

Resetting the REMOTE MODE Buttons

You can reset a REMOTE MODE button to its default remote control code.

While holding down the REMOTE MODE button

that you want to reset, press and hold down HOME until the remote indicator lights (about 3 seconds).

Within 30 seconds, press the REMOTE MODE

button again.

The remote indicator flashes twice, indicating that the button has been reset. Each REMOTE MODE button is preprogrammed with a remote control code. When a button is reset, its preprogrammed code is restored.

Resetting the Remote Controller

You can reset the remote controller to its default settings.

While holding down RECEIVER, press and hold

down HOME until the remote indicator lights (about 3 seconds).

Within 30 seconds, press RECEIVER again.

The remote indicator flashes twice, indicating that the remote controller has been reset.

En-56

Page 57

Controlling Other Components

By pressing the REMOTE MODE button that’s been programmed with the remote control code for your component, you can control Onkyo component as described below.

For details on entering a remote control code for other components, see “Entering Remote Control Codes” (➔ page 55).

Controlling a Blu-ray Disc/DVD Player, HD DVD Player

BD/DVD is preprogrammed with the remote control code

for controlling a component that supports the p (limited to some models). The component must be able to

receive remote control commands via p and be connected to the AV receiver via HDMI.

Use the following remote control codes:

` 32910/33001/31612:

Blu-ray Disc/DVD player with p

The p supported by the AV receiver is the CEC system control function of the HDMI standard.

Controlling Other Components

Press the appropriate REMOTE MODE button first.

i j

c d

l m

■ Blu-ray Disc player / HD-DVD player operation

Available buttons

a 8 g

TOP MENU

b c q/w/e/r, ENTER h

SETUP

d e 1, 3, 2, 5, 4,

7, 6 Red (A)

Green (B) Yellow (C) Blue (D)

Number: 1 to 9, 0 Number: +10

DISPLAY

MUTING

DISC +/–

RETURN

AUDIO

CLR

■ DVD player operation

Available buttons

a 8 g

TOP MENU

b c q/w/e/r, ENTER h

SETUP

d e 1, 3, 2, 5, 4,

7, 6

REPEAT

RANDOM

MODE

Number: 1 to 9, 0 Number: +10

DISPLAY

MUTING

DISC +/–

RETURN

AUDIO

CLR

En-57

Page 58

Press the appropriate REMOTE MODE button first.

c d

i j

■ CD player / CD recorder / MD recorder operation

Available buttons

a 8 g c q/w/e/r, ENTER

SETUP

d e 1, 3, 2, 5, 4,

7, 6

REPEAT

RANDOM

MODE

Number: 1 to 9, 0 Number: +10

DISPLAY

MUTING

DISC +/–

CLR

■ Cassette tape deck operation

Available buttons

a 8 i e 1, t (reverse

playback), 2, 5, 4, 7, 6

Note

• With some components, certain buttons may not work as expected, and some may not work at all.

• See “Controlling Your iPod/iPhone” about the operation of iPod/iPhone (➔ page 54).

The p function is not supported. The p supported by the AV receiver is the CEC system control function of the HDMI standard.

MUTING

Controlling Other Components

En-58

Page 59

Appendix

Troubleshooting

If you have any trouble using the AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact your Onkyo dealer.

If you can’t resolve the issue yourself, try resetting the AV receiver before contacting your Onkyo dealer.

To reset the AV receiver to its factory defaults, turn it on and, while holding down VCR/DVR, press

8ON/STANDBY. “Clear” will appear on the AV receiver’s display and the AV receiver will enter standby mode.

Note that resetting the AV receiver will delete your radio presets and custom settings.

Remote indicator

RECEIVER

HOME

To reset the remote controller to its factory defaults, while holding down RECEIVER, press and hold down HOME until the remote indicator lights (about 3 seconds). Within 30 seconds, press RECEIVER again.

The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

Power

■ Can’t turn on the AV receiver

Make sure that the power cord is properly plugged into the wall outlet.

Unplug the power cord from the wall outlet, wait five seconds or more, then plug it in again.

■ The AV receiver turns off unexpectedly

The AV receiver will automatically enter standby mode when Auto Standby has been set and launches.

■ The AV receiver turns off and after restoring the

power, it turns off again

The protection circuit has been activated. Remove the power cord from the wall outlet immediately. Make sure that all speaker cables and input sources are properly connected, and leave the AV receiver with its power cord disconnected for 1 hour. After that, reconnect the power cord and turn the power on. If the AV receiver turns off again, unplug the power cord and contact your Onkyo dealer. Caution: If “CHECK SP WIRE” appears on the AV receiver’s display, the speaker cables may be shorting.

WARNING

If smoke, smell or abnormal noise is produced by the AV receiver, unplug the power cord from the wall outlet immediately and contact your Onkyo dealer.

—

Audio

■ There’s no sound, or it’s very quiet

Make sure that the digital input source is selected properly.

Make sure that all audio connecting plugs are pushed in all the way.

Make sure that the inputs and outputs of all components are connected properly.

Make sure that the polarity of the speaker cables is correct, and that the bare wires are in contact with the metal part of each speaker terminal.

Make sure that the input source is properly selected. 20 Make sure that the speaker cables are not shorting. 12 Check the volume. The AV receiver is designed for

home theater enjoyment. It has a wide volume range, allowing precise adjustment.

If the MUTING indicator is flashing on the AV receiver’s display, press the remote controller’s MUTING to unmute the AV receiver.

While a pair of headphones is connected to the PHONES jack, no sound is output from the speakers.

If there’s no sound from a DVD player connected to an HDMI IN, check the DVD player’s output settings, and be sure to select a supported audio format.

Check the digital audio output setting on the connected device. On some game consoles, such as those that support DVD, the default setting is off.

With some DVD-Video discs, you need to select an audio output format from a menu.

If your turntable uses an MC cartridge, you must connect an MC head amp, or an MC transformer.

Make sure that none of the connecting cables are bent, twisted, or damaged.

Not all listening modes use all speakers. 31 Specify the speaker distances and adjust the

individual speaker levels. Make sure that the speaker setup microphone is not

still connected.

15-17

—

En-59

Page 60

If the input signal format is set to “PCM” or “DTS”. Set it to “Off”.

■ Only the front speakers produce sound

When the Stereo or Mono listening mode is selected, only the front speakers and subwoofer produce sound.

Check the Speaker Configuration. 42

■ Only the center speaker produces sound

If you use the Dolby Pro Logic IIx Movie, Dolby Pro Logic IIx Music, or Dolby Pro Logic IIx Game listening mode with a mono source, such as an AM radio station or mono TV program, the sound is concentrated in the center speaker.

Make sure the speakers are configured correctly. 42

■ The surround speakers produce no sound

When the T-D (Theater-Dimensional), Stereo or Mono listening mode is selected, the surround speakers produce no sound.

Depending on the source and current listening mode, not much sound may be produced by the surround speakers. Try selecting another listening mode.

Make sure the speakers are configured correctly. 42

■ The center speaker produces no sound

When the Stereo or Mono listening mode is selected, the center speaker produces no sound.

Make sure the speakers are configured correctly. 42

■ The front high or surround back speakers

produce no sound

Depending on the current listening mode, no sound may be produced by the front high or surround back speakers. Select another listening mode.

Not much sound may be produced by the front high or surround back speakers with some sources.

Make sure the speakers are configured correctly. 42

—

■ The subwoofer produces no sound

When you play source material that contains no information in the LFE channel, the subwoofer produces no sound.

Make sure the speakers are configured correctly. 42

—

■ There’s no sound with a certain signal format

Check the digital audio output setting on the connected device. On some game consoles, such as those that support DVD, the default setting is off.

With some DVD-Video discs, you need to select an audio output format from a menu.

Depending on the input signal, some listening modes cannot be selected.

—

31-32

■ Can’t get 6.1/7.1 playback

If no surround back speakers or front high speakers are connected, 6.1/7.1 playback is not possible.

Depending on the number of connected speakers, it is not always possible to select all of the listening modes.

—

31-32

■ The speaker volume cannot be set as required

After the volume level of each individual speaker has been adjusted, the maximum volume may be reduced.

If the volume level of each individual speaker has been adjusted to high positive values, then the maximum master volume possible may be reduced. Note that the individual speaker volume levels are set automatically after the Audyssey 2EQ Correction and Speaker Setup has been completed.

Room

27, 44

■ Noise can be heard

Using cable ties to bundle audio cables with power cords, speaker cables, and the like may degrade the audio performance, so refrain from doing it.

An audio cable may be picking up interference. Try repositioning your cables.

—

Appendix

■ The Late Night function doesn’t work

Make sure the source material is Dolby Digital, Dolby Digital Plus, or Dolby TrueHD.

■ About DTS signals

When DTS program material ends and the DTS bitstream stops, the AV receiver remains in DTS listening mode and the dts indicator remains on. This is to prevent noise when you use the pause, fast forward, or fast reverse function on your player. If you switch your player from DTS to PCM, you may not hear any sound because the AV receiver does not switch formats immediately. In such case, you should stop your player for about three seconds and then resume playback.

With some CD and LD players, you won’t be able to playback DTS material properly even though your player is connected to a digital input on the AV receiver. This is usually because the DTS bitstream has been processed (e.g., output level, sampling rate, or frequency response changed) and the AV receiver doesn’t recognize it as a genuine DTS signal. In such cases, you may hear noise.

Playing DTS program material, using the pause, fast forward, or fast reverse function on your player may produce a short audible noise. This is not a malfunction.

—

■ The beginning of audio received by an HDMI IN

can’t be heard

Since it takes longer to identify the format of an HDMI signal than it does for other digital audio signals, audio output may not start immediately.

—

En-60

Page 61

Video

■ There’s no picture

Make sure that all video connecting plugs are pushed in all the way.

Make sure that each video component is properly connected.

If the video source is connected to a component video input, you must assign that input to an input selector, and your TV must be connected to COMPONENT VIDEO OUT.

If the video source is connected to a composite video input, your TV must be connected to the corresponding composite video output.

If the video source is connected to an HDMI input, you must assign that input to an input selector, and your TV must be connected to the HDMI OUT.

On your TV, make sure that the video input to which the AV receiver is connected is selected.

■ There’s no picture from a source connected to

an HDMI IN

Reliable operation with an HDMI-to-DVI adapter is not guaranteed. In addition, video signals from a PC are not guaranteed.

■ The on-screen menus don’t appear

On your TV, make sure that the video input to which the AV receiver is connected is selected.

When the AV receiver is not connected to a TV via

HDMI OUT, on-screen menus are not displayed.

15, 17

16, 41

15, 41

—

Tuner

■ Reception is noisy, FM stereo reception is noisy,

or the FM STEREO indicator doesn’t light

Relocate your antenna. — Move the AV receiver away from your TV or

computer. Listen to the station in mono. 24 When listening to an AM station, operating the

remote controller may cause noise. Passing cars and airplanes can cause interference. — Concrete walls weaken radio signals. — If nothing improves the reception, install an outdoor

antenna.

—

Remote Controller

■ The remote controller doesn’t work

Before operating this unit, be sure to press RECEIVER.

Make sure that the batteries are installed with the correct polarity.

Install new batteries. Don’t mix different types of batteries, or old and new batteries.

Make sure that the remote controller is not too far away from the AV receiver, and that there’s no obstruction between the remote controller and the AV receiver’s remote control sensor.

Make sure that the AV receiver is not subjected to direct sunshine or inverter-type fluorescent lights. Relocate if necessary.

If the AV receiver is installed in a rack or cabinet with colored-glass doors, the remote controller may not work reliably when the doors are closed.

Make sure you’ve selected the correct remote controller mode.

Make sure you’ve entered the correct remote control code.

Make sure to set the same ID on both the AV receiver and remote controller.

—

10, 55

■ Can’t control other components

If it’s an Onkyo component, make sure that the u cable and analog audio cable are connected properly.

Connecting only an u cable won’t be enough. Make sure you’ve selected the correct remote

controller mode. For a proper operation of the remote controller as a

cassette tape deck is connected to the TV/CD IN jack, or as an RI Dock is connected to the TV/CD IN, VCR/DVR IN or GAME IN jacks, you must set the input display accordingly.

If you cannot operate it, you will need to enter the appropriate remote control code.

To control an Onkyo component that’s connected via u, point the remote controller at the AV receiver.

Be sure to enter the appropriate remote control code first.

To control an Onkyo component that’s not connected via u, point the remote controller at the component.

Be sure to enter the appropriate remote control code first.

u Dock for iPod/iPhone

■ There’s no sound

Make sure your iPod/iPhone is actually playing. — Make sure your iPod/iPhone is properly inserted in

the Dock. Make sure the AV receiver is turned on, the correct

input source is selected, and the volume is turned up. Make sure the plugs are pushed in all the way. — Try resetting your iPod/iPhone. —

■ There’s no video

Make sure that your iPod/iPhone model’s TV OUT setting is set to On.

Make sure the correct input is selected on your TV or the AV receiver.

Some versions of the iPod/iPhone do not output video.

Appendix

10, 57

—

En-61

Page 62

■ The AV receiver’s remote controller doesn’t

control my iPod/iPhone

Make sure your iPod/iPhone is properly inserted in the Dock. If your iPod/iPhone is in a case, it may not connect properly to the Dock. Always remove your iPod/iPhone from the case before inserting it into the Dock.

The iPod/iPhone cannot be operated while it’s displaying the Apple logo.

Make sure you’ve selected the right remote mode. 54 When you use the AV receiver’s remote controller,

point it toward your AV receiver. If you still can’t control your iPod/iPhone, start

playback by pressing your iPod/iPhone model’s Play button. Remote operation should then be possible.

Try resetting your iPod/iPhone. — Depending on your iPod/iPhone, some buttons may

not work as expected.

—

■ The AV receiver unexpectedly selects my

iPod/iPhone as the input source

Always pause iPod/iPhone playback before selecting a different input source. If playback is not paused, the Direct Change function may select your iPod/iPhone as the input source by mistake during the transition between tracks.

—

■ iPod/iPhone doesn’t work properly

Try reconnecting your iPod/iPhone. —

Recording

■ Can’t record

On your recorder, make sure the correct input is selected.

To prevent signal loops and damage to the AV receiver, input signals are not fed through to outputs with the same name (e.g., VCR/DVR IN to VCR/DVR OUT).

—

USB Device Playback

■ Can’t access the music files on a USB device

Make sure the USB device is plugged in properly. — The AV receiver supports USB devices that support

the USB mass storage device class. However, playback may not be possible with some USB devices even if they conform to the USB mass storage device class.

USB memory devices with security functions cannot be played.

Others

■ Standby power consumption

In the following cases, the power consumption in standby mode may reach up to a maximum of 34 W:

–“HDMI Ctrl (RIHD)” setting is set to “On”.

(Depending on the TV status, the AV receiver will enter standby mode as usual.)

–The “HDMI Through” setting is set to other than

“Off”.

■ The sound changes when I connect my

headphones

When a pair of headphones is connected, the listening mode is set to Stereo, unless it’s already set to Stereo, Mono, or Direct.

■ The speaker distance cannot be set as required

The values entered may be automatically adjusted with values best-suited for your home theater.

■ How do I change the language of a multiplex

source

Use the “Input Ch (Mux)” setting on the “Audio Adjust” menu to select “Main” or “Sub”.

—

Appendix

■ The u functions don’t work

To use u, you must make an u connection and an analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally.

■ When performing “Automatic Speaker Setup”,

the measurement fails and the message “Ambient noise is too high.” is displayed.

This can be caused by a malfunction in your speaker unit. Check if the unit produces normal sounds.

—

En-62

Page 63

■ The following settings can be made for the

composite video inputs

You must use the buttons on the unit to make these settings. On the AV receiver, press the input selector for the input source that you want to set and the SETUP button simultaneously. While holding down the input selector button, press SETUP until “Video ATT :On” appears on the AV receiver’s display. Then, release both buttons. To turn the setting off, repeat the above process so that “Video ATT :Off” appears on the AV receiver’s display, and release the buttons.

• Video Attenuation

This setting can be made for the BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX, or USB input.

If you have a games console connected to the composite video input, and the picture isn’t very clear, you can attenuate the gain.

Video ATT :Off: (default). Video ATT :On: Gain is reduced by 2 dB.

■ If the picture on your TV/monitor connected to

the HDMI OUT is unstable, try switching the DeepColor function off

To turn off the DeepColor function, simultaneously press the CBL/SAT and 8ON/STANDBY buttons on

the AV receiver. While holding down CBL/SAT, press 8ON/STANDBY until “Deep Color: Off” appears on

the AV receiver’s display. Then, release both buttons. To reactivate the DeepColor function, repeat the above process until “Deep Color: On” appears on the AV receiver’s display and release the buttons.

Appendix

The AV receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this happens, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in.

Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit’s malfunction. Before you record important data, make sure that the material will be recorded correctly.

Before disconnecting the power cord from the wall outlet, set the AV receiver to standby.

En-63

Page 64

Appendix

Connection Tips and Video Signal Path

The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format you choose will depend on the formats supported by your components. Use the following sections as a guide.

The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

Note

• The on-screen setup menus are displayed when: – There is no video input, or – The video input is 480p, 576p, 720p, 1080i, or 1080p.

Video Connection Formats

Video components can be connected by using any one of the following video connection formats: composite video, component video, or HDMI, the latter offering the best picture quality.

When choosing a connection format, bear in mind that the AV receiver doesn’t convert between formats, so only outputs of the same format as the input will output the signal.

Video Signal Flow Chart

Blu-ray Disc/DVD player, etc.

Composite

AV receiver

Composite

Component

MONITOR OUT

Component

TV, projector, etc.

HDMI

Audio Connection Formats

Audio components can be connected by using any of the following audio connection formats: analog, optical, coaxial, or HDMI. When choosing a connection format, bear in mind that the AV receiver does not convert digital input signals for analog line outputs and vice versa. For example, audio signals connected to an optical or coaxial digital input are not output by the analog VCR/DVR OUT.

If signals are present at more than one input, the inputs will be selected automatically in the following order of priority: HDMI, digital, analog.

Audio Signal Flow Chart

Blu-ray Disc/DVD player, etc.

HDMICoaxial Analog

HDMI Analog

AV receiver

Optical

OUT

TV, projector, etc.

En-64

Depends on the “Audio TV Out” setting (➔ page 50).

This is possible, when “Audio Return Ch” is set to “Auto” (➔ page 50), the TV/CD input selector is selected, and your TV is ARC capable.

Tip

• When a signal is input via HDMI and the corresponding input selector is selected, the HDMI indicator lights.

Page 65

Appendix

Using an RIHDcompatible TV, Player, or Recorder

p, which stands for Remote Interactive over HDMI, is the name of the system control function found on Onkyo components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over HDMI and is part of the HDMI standard. CEC provides interoperability between various components, however, operation with components other

than p-compatible components cannot be guaranteed.

About p-compatible components

The following components are p-compatible (As of January 2012).

■ TV

• Toshiba TV

•Sharp TV

■ Players/Recorders

• Onkyo and Integra p-compatible players

• Toshiba players and recorders (only when used together with Toshiba TV)

• Sharp players and recorders (only when used together with Sharp TV)

Models other than those mentioned above may have some interoperability if compatible with CEC which is part of the HDMI Standard, but operation cannot be guaranteed.

Note

• For proper linked operations, do not connect more p- compatible components than the quantities specified below, to the HDMI input terminal. – Blu-ray Disc/DVD players: up to three. – Blu-ray Disc/DVD recorders/Digital Video Recorders: up to

three.

– Cable/Satellite Set-top boxes: up to four.

• Do not connect the AV receiver to the other AV receiver/AV amplifier via HDMI.

• Proper linked operations are not guaranteed when more p-compatible components than the above-mentioned

quantities are connected.

Operations that can be performed with p connection

■ For p-compatible TV

The following linked operations are enabled by connecting the AV receiver to an p-compatible TV.

• The AV receiver will enter standby mode when the TV is set to standby.

• You can set on the menu screen of the TV to either output the audio from the speakers connected to the AV receiver, or from the speakers of the TV.

• It is possible to output the audio coming from the tuner or auxiliary input of your TV to the speakers of the AV receiver. (A connection such as an optical digital cable or similar is required in addition to the HDMI cable.)

• Input to the AV receiver can be selected with the remote controller of the TV.

• Operations such as volume adjustment or similar for the AV receiver can be performed from the remote controller of the TV.

■ For p-compatible players/recorders

The following linked operations are enabled by connecting the AV receiver to an p-compatible

player/recorder.

• When the playback is started on the player/recorder, input of the AV receiver will switch to the HDMI input of the player/recorder that is playing back.

• Operation of the player/recorder is possible using the remote controller supplied with the AV receiver.

Depending on the model used, not all operations may be available.

En-65

To be continued

Page 66

■ How to connect and setup

Confirm the connecting and setting.

1. Connect the HDMI OUT jack to the HDMI input jack of the TV.

Blu-ray Disc/DVD player, etc.

HDMI connection

AV receiver

DIGITAL AUDIO connection (OPTICAL)

TV, projector, etc.

HDMI connection

2. Connect the audio output from the TV to the OPTICAL IN 2 jack of the AV receiver using an optical digital cable.

Note

• When the audio return channel (ARC) function is used with

an ARC capable TV, this connection is not necessary (➔ page 50).

3. Connect the HDMI output of the Blu-ray Disc/DVD player/recorder to the HDMI IN 1 jack of the AV receiver.

Note

• It is necessary to assign the HDMI input when connecting

the Blu-ray Disc/DVD player/recorder to other jacks (➔ page 41). Do not assign an HMDI IN to the TV/CD selector at this time, otherwise appropriate CEC (Consumer Electronics Control) operation will not be guaranteed.

Change each item in the “HDMI Setup” menu

according to the following settings:

• HDMI Ctrl (RIHD): On

• Audio Return Ch (ARC): Auto

See details of each setting (➔ pages 49, 50).

Confirm the settings.

1. Turn on the power for all connected components.

2. Turn off the power of the TV, and confirm that the power of the connected components is turned off automatically with the link operation.

3. Turn on the power of the Blu-ray Disc/DVD player/recorder.

4. Start playback on the Blu-ray Disc/DVD player/recorder, and verify the following.

• The AV receiver automatically turns on, and

selects the input to which the Blu-ray Disc/DVD player/recorder is connected.

• The TV automatically turns on, and selects the

input to which the AV receiver is connected.

5. Following the operating instructions of the TV, select “Use the TV speakers” from the menu screen of the TV, and confirm that the audio is output from the speakers of the TV, and not from the speakers connected to the AV receiver.

6. Select “Use the speakers connected from the AV receiver” from the menu screen of the TV, and confirm that the audio is output from the speakers connected to the AV receiver, and not from the TV speakers.

Note

• Perform the above operations when you use the AV receiver

for the first time, when the settings of each component are changed, when the main power of each component is turned off, when the power cable is disconnected from the power supply, or when there has been a power outage.

Operate with the remote controller.

For buttons that can be operated (➔ page 55).

Note

• Audio from DVD-Audio or Super Audio CD may not output from the TV speakers. You will be able to output the audio from the TV speakers by setting the audio output of the DVD player to 2ch PCM. (It may not be possible depending on the player models.)

• Even if you set to output audio on the TV speakers, audio will be output from the speakers connected to the AV receiver when you adjust the volume or switch the input on the AV receiver. To output audio from the TV speakers, redo the operations on the TV.

• In case of an p connection with u and u audio control compatible components, do not connect the u

cable at the same time.

• On the TV, when you select anything other than the HDMI jack to which the AV receiver is connected, the input on the AV receiver will be switched to “TV/CD”.

• The AV receiver will automatically power on in conjunction when it determines it to be necessary. Even if the AV

receiver is connected to an p compatible TV or player/recorder, it will not power on if it is not necessary. It may not power on in conjunction when the TV is set to output audio from the TV.

• Linked functions with the AV receiver may not work depending on the component model connected. In such cases, operate the AV receiver directly.

Appendix

En-66

Page 67

Appendix

About HDMI

Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital interface standard for connecting TVs, projectors, Blu-ray Disc/DVD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components. With HDMI, a single cable can carry control signals, digital video, and up to eight channels of digital audio (2channel PCM, multichannel digital audio, and multichannel PCM).

The HDMI video stream (i.e., video signal) is compatible with DVI (Digital Visual Interface) with a DVI input can be connected by using an HDMI-toDVI adapter cable. (This may not work with some TVs and displays, resulting in no picture.) The AV receiver uses HDCP (High-bandwidth Digital Content Protection)*2, so only HDCP-compatible components can display the picture.

The AV receiver’s HDMI interface is based on the following:

Audio Return Channel, 3D, x.v.Color, DeepColor, Lip Sync, DTS-HD Master Audio, DTS-HD High Resolution Audio, Dolby TrueHD, Dolby Digital Plus, DSD and Multichannel PCM.

, so TVs and displays

Supported Audio Formats About Copyright Protection

• 2-channel linear PCM (32–192 kHz, 16/20/24 bit)

• Multichannel linear PCM (up to 7.1 ch, 32–192 kHz, 16/20/24 bit)

• Bitstream (DSD, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS, DTS-HD High Resolution Audio, DTS-HD Master Audio)

Your Blu-ray Disc/DVD player must also support HDMI output of the above audio formats.

The AV receiver supports HDCP (High-bandwidth Digital

Content Protection)

, a copy-protection system for digital video signals. Other devices connected to the AV receiver via HDMI must also support HDCP.

DVI (Digital Visual Interface): The digital display interface standard set by the DDWG

HDCP (High-bandwidth Digital Content Protection): The video encryption technology developed by Intel for HDMI/DVI. It’s designed to protect video content and requires a HDCP-compatible device to display the encrypted video.

DDWG (Digital Display Working Group): Lead by Intel, Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and Silicon Image, this open industry group’s objective is to address the industry’s requirements for a digital connectivity specification for high-performance PCs and digital displays.

Note

• The HDMI video stream is compatible with DVI (Digital Visual

Interface), so TVs and displays with a DVI input can be connected by using an HDMI-to-DVI adapter cable. (Note that DVI connections only carry video, so you’ll need to make a separate connection for audio.) However, reliable operation with such an adapter is not guaranteed. In addition, video signals from a PC are not supported.

• The HDMI audio signal (sampling rate, bit length, etc.) may be

restricted by the connected source component. If the picture is poor or there’s no sound from a component connected via HDMI, check its setup. Refer to the connected component’s instruction manual for details.

in 1999.

En-67

Page 68

Appendix

USB Features

USB Device Requirements

• USB mass storage device class (but not always guaranteed).

• FAT16 or FAT32 file system format.

• Up to 255 folders can be displayed, and folders may be nested up to 8 levels deep.

• USB hubs and USB devices with hub functions are not supported.

Note

• If the media you connect is not supported, the message “No Storage” will be displayed.

• If you connect a USB hard disk drive to the AV receiver’s USB port, we recommend that you use its AC adapter to power it.

• The AV receiver supports USB MP3 players that support the USB Mass Storage Class standard, which allows USB devices to be connected to computers without the need for special drivers or software. Note that not all USB MP3 players support the USB Mass Storage Class standard. Refer to your USB MP3 player’s instruction manual for details.

• Protected WMA music files on an MP3 player cannot be played.

• Onkyo accepts no responsibility whatsoever for the loss or damage to data stored on a USB device when that device is used with the AV receiver. We recommend that you back up your important music files beforehand.

• MP3 players containing music files that are managed with special music software are not supported.

• Operation is not guaranteed for all USB devices, which includes the ability to power them.

• Do not connect your USB device via a USB hub. The USB device must be connected directly to the AV receiver’s USB port.

• If the USB device contains a lot of data, the AV receiver may take a while to read it.

• USB devices with security functions cannot be played.

Supported Audio File Formats

For playback from a USB device, the AV receiver supports the following music file formats. Variable bit-rate (VBR) files are supported. However, playback time may not be display correctly.

■ MP3 (.mp3 or .MP3)

• MP3 files must be MPEG-1/MPEG-2.5 Audio Layer 3 format with a sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz and bitrates of between 8 kbps and 320 kbps. Incompatible files cannot be played.

■ WMA (.wma or .WMA)

WMA stands for Windows Media Audio and is an audio compression technology developed by Microsoft Corporation. Audio can be encoded in WMA format by using Windows Media

• WMA files must have the copyright option turned off.

• Sampling rates of 32 kHz, 44.1 kHz, 48 kHz, bitrates of between 48 kbps and 320 kbps are supported.

• WMA DRM/Pro/Voice formats are not supported.

■ AAC (.aac/.m4a/.mp4/.AAC/.M4A or .MP4)

AAC stands for MPEG-2/MPEG-4 Audio.

• Sampling rates of 16 kHz, 22.05 kHz, 24 kHz, 32 kHz,

44.1 kHz, 48 kHz and bitrates of between 8 kbps and 320 kbps are supported.

■ FLAC (.flac or .FLAC)

FLAC is a file format for lossless audio data compression.

• Sampling rates of 32 kHz, 44.1 kHz and 48 kHz are supported.

• Quantization bit: 16 bit, 24 bit

Player.

En-68

Page 69

License and Trademark Information

“x.v.Color” is a trademark of Sony Corporation.

Appendix

Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide patents issued & pending. DTS-HD, the Symbol, & DTS-HD and the Symbol together are registered trademarks & DTS-HD Master Audio is a trademark of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the double-D symbol are trademarks of Dolby Laboratories.

Music Optimizer™ is a trademark of Onkyo Corporation.

“HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.”

iPhone, iPod, iPod classic, iPod nano, iPod shuffle, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance.

Manufactured under license from Audyssey Laboratories™, Inc. U.S. and foreign patents pending. Audyssey 2EQ Audyssey Dynamic EQ registered trademarks of Audyssey Laboratories, Inc.

and Audyssey Dynamic Volume® are

En-69

Page 70

Specifications

Amplifier Section

Rated Output Power All channels: (North American and Brazilian)

Maximum Effective Output Power

Dynamic Power

IEC60268-Short-term maximum output power

THD+N (Total Harmonic Distortion+Noise)

Damping Factor 60 (Front, 1 kHz, 8 Ω) Input Sensitivity and Impedance (Unbalance)

Rated RCA Output Level and Impedance

Maximum RCA Output Level and Impedance

Frequency Response 5 Hz - 100 kHz/+1 dB, -3 dB (DSP bypass) Tone Control Characteristics

Signal to Noise Ratio 100 dB (LINE, IHF-A) Speaker Impedance 6 Ω - 16 Ω

80 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.7% (FTC)

130 watts minimum continuous power per channel, 6 ohm loads, 1 channel driven at 1 kHz, with a maximum total harmonic distortion of 1%

(Asian)

7 ch × 130 W at 6 ohms, 1 kHz, 1 ch driven of 1 % (IEC)

(Asian)

7 ch × 160 W at 6 ohms, 1 kHz, 1 ch driven (JEITA)

180 W (3 Ω, Front) 160 W (4 Ω, Front) 100 W (8 Ω, Front)

0.08% (20 Hz - 20 kHz, half power)

200 mV/47 kΩ (LINE)

200 mV/2.2 kΩ (REC OUT)

2 V/2.2 kΩ (REC OUT)

±10 dB, 50 Hz (BASS) ±10 dB, 20 kHz (TREBLE)

Video Section

Input Sensitivity/Output Level and Impedance

1 Vp-p/75 Ω (Component Y)

0.7 Vp-p/75 Ω (Component PB/CB, PR/CR) 1 Vp-p/75 Ω (Composite)

Component Video Frequency Response

5 Hz - 100 MHz/+0 dB, -3 dB

Tuner Section

FM Tuning Frequency Range

(North American and Brazilian)

87.5 MHz - 107.9 MHz (Asian)

87.5 MHz - 108.0 MHz, RDS

AM Tuning Frequency Range

522/530 kHz - 1611/1710 kHz

Preset Channel 40

General

Power Supply (North American and Brazilian)

Power Consumption (North American and Brazilian) 5 A

No-sound Power Consumption

Stand-by Power Consumption

Dimensions (W × H × D)

Weight (North American and Brazilian)

AC 120 V, 60 Hz

(Asian) AC 220 - 240 V, 50/60 Hz

(Asian) 530 W

(North American and Brazilian) 65W (Asian)

65 W (230 V) 70 W (240 V)

(North American and Brazilian) 0.2 W (Asian) 0.3 W

435 mm × 150 mm × 328 mm 17-1/8" × 5-7/8" × 12-15/16"

8.4 kg (18.5 lbs.)

(Asian)

9.0 kg (19.8 lbs.)

Appendix

■ HDMI

Input IN 1, IN 2, IN 3, IN 4 Output OUT Video Resolution 1080p Audio Format Dolby TrueHD, DTS-HD Master Audio,

Supported 3D, Audio Return Channel, DeepColor,

DVD-Audio, DSD

x.v.Color, LipSync, CEC (RIHD)

■ Video Inputs

Component IN 1, IN 2 Composite BD/DVD, VCR/DVR, CBL/SAT, GAME,

AUX

■ Video Outputs

Component OUT Composite MONITOR OUT, VCR/DVR OUT

■ Audio Inputs

Digital Optical: 2

Analog BD/DVD, VCR/DVR, CBL/SAT, GAME,

Coaxial: 2

TV/CD, AUX

■ Audio Outputs

Analog VCR/DVR Subwoofer Pre Output

Speaker Outputs Main (L, R, C, SL, SR, SBL/FHL,

Phones 1 (6.3 ø)

SBR/FHR)

■ Others

Setup Mic 1 USB 1 (Front) RI 1

Specifications and features are subject to change without notice.

En-70

Page 71

Memo

Appendix

En-71

Page 72

2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8163 http://www.onkyo.com/

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/

Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4208-213 http://www.eu.onkyo.com/

The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700

Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong. Tel: 852-2429-3118 Fax: 852-2428-9039 http://www.onkyochina.com/

1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai, China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396

http://www.cn.onkyo.com/

SN 29401056

Y1112-1

* 2 9 4 0 1 0 5 6 *

Page 73

7.1ch Home Theater Speaker Package

HTP-591

Supplied Accessories

Make sure you have the following accessories.

Front speakers (SKF-591)

(White)

Front speakers

Speaker cables 10 ft. (3.0 m)

Center speaker (SKC-591N/SKC-591)

Center speaker Speaker cable

SKC-591N (North American and Brazilian) SKC-591 (Asian)

4 rubber stoppers

Configuration of the rubber stoppers may be different from the figure, such as being 2 sheets instead of 1 sheet, but the total number will be same.

(Red)

(Green)

10 ft. (3.0 m)

Surround speakers (SKR-590) Surround back speakers (SKB-590)

Surround speakers

Surround back

speakers

(Blue)

(Brown)

Speaker cables 26 ft. (8.0 m)

Powered subwoofer (SKW-591)

Subwoofer RCA cable

4 floor pads

10 ft. (3.0 m)

(Gray)

(Tan)

Part Names

Keyhole slot

Speaker terminals

SKF-591

Speaker terminals

SKC-591N/ SKC-591

Keyhole slots

Keyhole slot

Speaker terminals

SKR-590/SKB-590

Caution

• The front grilles are not designed to be removed so do not attempt to remove them forcibly, as this will damage them.

En-1

Page 74

■ Front

Status indicator

Off: Subwoofer in standby mode or

disconnected from power source Blue: Subwoofer on With the Auto Standby function, the SKW-591 automatically turns on when an input signal is detected in standby mode. When there’s no input signal for

SKW-591

a while, the SKW-591 automatically enters standby mode.

■ Rear

(North American)

SKW-591

To AC outlet

(Asian) (Brazilian)

OUTPUT LEVEL control

This control is used to adjust the volume of the subwoofer.

LINE INPUT

This RCA input should be connected to the subwoofer pre out on your AV receiver with supplied RCA cable.

Before Using the Home Theater Speaker Package

Using the Rubber Stoppers for a More Stable Platform

We recommend using the supplied rubber stoppers to achieve the best possible sound from your speakers. The rubber stoppers prevent the speakers from moving, providing a more stable platform. Use rubber stoppers for the center speaker.

Rubber stoppers

Bottom of the SKC-591N/SKC-591

Using the Floor Pads for Subwoofer

Setting the Subwoofer Level

To set the level of the subwoofer, use the OUTPUT LEVEL control. Set it so that bass sounds are evenly balanced with the treble sounds from the other speakers. Because our ears are less sensitive to very low bass sounds, there’s a temptation to set the level of the subwoofer too high. As a rule of thumb, set the subwoofer level to what you think is the optimal level, and then back it off slightly.

Wall Mounting

To mount the front/surround/surround back speakers vertically, use the keyhole slot shown to hang each speaker on a screw that’s securely screwed into the wall.

Keyhole slots for

wall mounting

Note

• The Auto Standby function turns the subwoofer on when the input signal exceeds a certain level. If the Auto Standby function does not work reliably, try slightly increasing or decreasing the subwoofer output level on your receiver.

If the subwoofer is placed on a hard floor (wood, vinyl, tile, etc.) and playback is very loud, the subwoofer’s feet may damage the flooring. To prevent this, place the supplied pads underneath the subwoofer’s feet. The pads also provide a stable base for the subwoofer.

Pad

En-2

SKF-591

SKR-590/SKB-590

To mount the center speaker horizontally, use the two keyhole slots shown to hang the speaker on two screws that are securely screwed into the wall.

Keyhole slots for wall mounting

SKC-591N/ SKC-591

7-7/8" (200 mm)

Tip

• If the center speaker is tilted, loosen the screw on the declined side to move upward so that the speaker could be adjusted vertically.

Page 75

Caution

• A mounting screw’s ability to support a

Wall

speaker depends on how well it’s anchored to the wall. If you have hollow walls, screw each mounting screw into a stud. If there are no studs, or the walls are solid, use suitable wall anchors. Use screws with a head

3/16" to 7/16" (5 to 10 mm)

diameter of 5/16" (9 mm) or less and a shank diameter of 1/8" (4 mm) or less. With hollow walls, use a cable/pipe detector to check for any power cables or water pipes before making any holes.

• Leave a gap of between 3/16" (5 mm) and 7/16" (10 mm) between the wall and the base of the screw head, as shown (We recommend that you consult a home installation professional).

Enjoying Home Theater

The Home Theater means that you can enjoy surround sound with a real sense of movement in your own home — just like being in a movie theater or concert hall.

a Front left and right speakers (SKF-591)

They should be positioned facing the listener at about ear level, and equally spaced from the TV. Angle them inward slightly so as to create a triangle, with the listener at the apex.

b Center speaker (SKC-591N/SKC-591)

Position it close to your TV (preferably on top) facing forward at about ear level, or at the same height as the front left and right speakers.

c Surround left and right speakers (SKR-590)

Position them at the sides of the listener, or slightly behind, about 2 to 3 feet (60 to 100 cm) above ear level. Ideally they should be equally spaced from the listener.

d Surround back left and right speakers (SKB-590)

These speakers further enhance the realism of surround sound and improve sound localization behind the listener. Position them behind the listener about 2 to 3 feet (60 to 100 cm) above ear level.

e Subwoofer (SKW-591)

The subwoofer handles the bass sounds of the LFE (Low-Frequency Effects) channel and bass from the satellite speakers when a crossover is specified. The volume and quality of the bass output from your subwoofer will depend on its position, the shape of your listening room, and your listening position. In general, a good bass sound can be obtained by installing the subwoofer in a front corner, or at onethird the way along the front wall, as shown.

eba

Corner position

1/3 of wall position

Connecting the Speakers

Speaker Connection Precautions

Read the following before connecting your speakers:

• Turn off your receiver before making any connections.

• Pay close attention to speaker wiring polarity. Connect positive (+) terminals to only positive (+) terminals, and negative (–) terminals to only negative (–) terminals. If the speakers are wired incorrectly, the sound will be out of phase and will sound unnatural.

• Be careful not to short the positive and negative wires. Doing so may damage your amp.

Note

• When you connect the front high left and right speakers, prepare for it separately, or use the surround back left and right speakers.

Powered

subwoofer

Using the supplied RCA cable, connect the subwoofer’s LINE INPUT to your AV receiver’s SUBWOOFER PRE OUT jack.

Front right

speaker

Center speaker

Red White

Brown

Surround

back left speaker

Surround

back right

speaker

Tan

Front left

speaker

Surround

left

speaker

Blue

Green

Surround

right

speaker

Gray

En-3

Page 76

Specifications

■ Powered Subwoofer (SKW-591)

Type Bass-Reflex Input sensitivity/Impedance

540 mV/20 kΩ

Rated output Power (FTC)

(North American and Brazilian)

120 watts minimum continuous power, 4 ohms, driven at 100 Hz with a maximum total harmonic distortion of 1%

Rated output Power (IEC)

(Asian)

120 watts minimum continuous power, 4 ohms, driven at 100 Hz with a maximum total harmonic distortion of 1%

Frequency response 25 Hz to 150 Hz Cabinet capacity 1.34 cubic feet (38 L) Dimensions (W × H × D) 12-1/2" × 18-7/16" × 15-11/16"

Weight 20.1 lbs. (9.1 kg) Audio Input 1 (RCA analog mono) Drivers unit 10" (25 cm) Cone Woofer × 1 Power supply (North American and Brazilian)

Power consumption 35 W Other Auto Standby function

■ Front Speakers (SKF-591)

Type 2 Way Bass-Reflex Impedance 6 Ω Maximum input power 130 W Sensitivity 84.5 dB/W/m Frequency response 55 Hz to 50 kHz Crossover frequency 4kHz Cabinet capacity 0.20 cubic feet (5.7 L) Dimensions (W × H × D) 6-1/8" × 14-7/8" × 6-5/8"

Weight 5.7 lbs. (2.6 kg) Drivers unit 5" (12 cm) OMF Cone Woofer × 1

(317.5 mm × 468 mm × 398 mm) (incl. projection)

AC 120 V, 60 Hz (Asian) AC 220 - 240 V, 50/60 Hz

Non-magnetic shielding

(155 mm × 378 mm × 169 mm) (incl. grille and projection)

1" (2.5 cm) Balanced Dome × 1

Terminal Spring type color coded Keyhole slot Available Grille Fixed Other Non-magnetic shielding

■ Center Speaker

SKC-591N (North American and Brazilian) Type 2 Way Bass-Reflex Impedance 6 Ω Maximum input power 130 W Sensitivity 86 dB/W/m Frequency response 65 Hz to 50 kHz Crossover frequency 6kHz Cabinet capacity 0.10 cubic feet (2.8 L) Dimensions (W × H × D) 16-9/16" × 4-1/2" × 4-11/16"

Weight 5.1 lbs. (2.3 kg) Drivers unit 3-1/4" (8 cm) Cone Woofer × 2

Terminal Spring type color coded Keyhole slot Available Grille Fixed Other Non-magnetic shielding

SKC-591 (Asian) Type 2 Way Bass-Reflex Impedance 6 Ω Maximum input power 130 W Sensitivity 86 dB/W/m Frequency response 65 Hz to 50 kHz Crossover frequency 6kHz Cabinet capacity 0.10 cubic feet (2.8 L) Dimensions (W × H × D) 16-9/16" × 4-1/2" × 4-11/16"

Weight 5.3 lbs. (2.4 kg) Drivers unit 3-1/4" (8 cm) Cone Woofer × 2

Terminal Spring type color coded Keyhole slot Available Grille Fixed Other Magnetic shielding

(420 mm × 115 mm × 119 mm) (incl. grille and projection)

1" (2.5 cm) Balanced Dome × 1

(420 mm × 115 mm × 119 mm) (incl. grille and projection)

1" (2.5 cm) Balanced Dome × 1

■ Surround/Surround Back Speakers

(SKR-590/SKB-590)

Type Full Range Closed Box Impedance 6 Ω Maximum input power 130 W Sensitivity 81 dB/W/m Frequency response 80 Hz to 20 kHz Cabinet capacity 0.036 cubic feet (1.0 L) Dimensions (W × H × D) 4-1/2" × 9-1/16" × 3-3/4"

Weight 2.2 lbs. (1.0 kg) Drivers unit 3-1/4" (8 cm) Cone Speaker × 1 Terminal Spring type color coded Keyhole slot Available Grille Fixed Other Non-magnetic shielding

(115 mm × 230 mm × 96 mm) (incl. grille and projection)

Specifications and appearance are subject to change without prior notice.

Note

For non-magnetic shielded speakers:

Try moving the speakers away from your TV or monitor. If discoloration should occur, turn off your TV or monitor, wait 15 to 30 minutes, and then turn it back on again. This normally activates the degaussing function, which neutralizes the magnetic field, thereby removing any discoloration effects.

En-4

Page 77

)

Ensemble d’enceintes du Home cinéma 7.1 can.

HTP-591

Accessoires fournis

Assurez-vous que le carton contient bien les accessoires suivants.

Enceintes avant (SKF-591)

(Blanc)

Enceintes avant

Câbles d’enceinte

Enceinte centrale (SKC-591N/SKC-591)

Enceinte centrale Câble d’enceinte 3,0 m

SKC-591N (Nord-américains et brésiliens) SKC-591 (Asie)

4 bouchons de

caoutchouc

La configuration des bouchons de caoutchouc peut être différente de la figure, en comportant par exemple 2 feuilles au lieu d’une, mais leur nombre total est identique.

(Rouge)

3,0 m

(Vert)

Enceintes surround (SKR-590) Enceintes surround arrière (SKB-590)

Enceintes surround

arrière

(Bleu)

(Marron)

Câbles d’enceinte 8,0 m

(Marron clair

Subwoofer amplifié (SKW-591)

Subwoofer Câble RCA 3,0 m

4 tampons de protection

(Gris)

Noms des pièces

Encoche en trou de serrure

Bornes d’enceinte

SKF-591

Bornes d’enceinte

SKC-591N/ SKC-591

Encoches en trou de serrure

Encoche en trou de serrure

Bornes d’enceinte

SKR-590/SKB-590

Mise en garde

• Les grilles avant ne sont pas faites pour être retirées, aussi n’essayez pas de les retirer de force, car ceci les endommagera.

Fr-1

Page 78

■ Avant

Indicateur d’état

Off : subwoofer en mode veille ou

débranché de la source

d’alimentation Bleu : subwoofer allumé Grâce à la fonction de mise en veille automatique, la SKW-591 s’allume automatiquement lorsqu’un signal

SKW-591

d’entrée est détecté en mode Veille. Lorsqu’aucun signal d’entrée n’est transmis pendant un certain temps, la SKW-591 passe automatiquement en mode Veille.

■ Arrière

(Nord-américains)

SKW-591

Vers la prise murale

(Asie) (Brésiliens)

Remarque

• La fonction de mise en veille automatique allume le subwoofer lorsque le signal d’entrée dépasse un certain niveau. Si la fonction de mise en veille automatique ne fonctionne pas correctement, essayez d’augmenter ou de diminuer légèrement le niveau de sortie du subwoofer de votre récepteur.

Bouton OUTPUT LEVEL

Ce bouton sert à régler le volume sonore du subwoofer.

LINE INPUT

Cette entrée RCA doit être branchée à la pré-sortie du subwoofer de votre ampli-tuner AV à l’aide du câble RCA fourni.

Avant d’utiliser l’Ensemble d’enceintes du Home cinéma

Utilisation des bouchons en caoutchouc pour une meilleure stabilité

Nous vous recommandons d’utiliser les bouchons en caoutchouc fournis pour obtenir le meilleur son possible de vos enceintes. Les bouchons en caoutchouc empêchent les enceintes de bouger, en procurant une meilleure stabilité. Utilisez les bouchons en caoutchouc pour l’enceinte centrale.

Bouchons de caoutchouc

Dessous de la SKC-591N/SKC-591

Utilisation des tampons de protection pour le subwoofer

Si le subwoofer est placé sur un sol dur (bois, vinyle, carrelage, etc.) et si le niveau sonore de la lecture est élevé, les pieds du subwoofer peuvent endommager le sol. Pour empêcher ceci, placez les tampons fournis sous les pieds du subwoofer. Les tampons fournissent également une base stable au subwoofer.

Réglage du niveau sonore du subwoofer

Pour régler le niveau sonore du subwoofer, utilisez le bouton OUTPUT LEVEL. Réglez-le de façon à ce que les basses soient équilibrées avec les aigus provenant des autres enceintes. Étant donné que nos oreilles sont moins sensibles aux basses très faibles, vous pouvez être tenté de régler le niveau sonore du subwoofer trop haut. En règle générale, réglez le niveau sonore du subwoofer au niveau que vous estimez être optimal, et diminuez-le légèrement.

Fixation au mur

Pour fixer les enceintes avant/surround/ façon verticale, utilisez l’encoche en trou de serrure pour accrocher chaque enceinte sur une vis bien vissée au mur.

Encoche en trou

de serrure pour la

fixation au mur

SKF-591

Pour fixer l’enceinte centrale de façon horizontale, utilisez les deux encoches en trou de serrure indiquées pour accrocher l’enceinte à deux vis bien fixées au mur.

Encoche en trou de serrure pour la fixation au mur

surround arrière

SKR-590/SKB-590

SKC-591N/ SKC-591

Fr-2

Tampon

200 mm

Conseil

• Si l’enceinte centrale est inclinée, dévissez la vis du côté incliné pour régler la position verticale de l’enceinte et la redresser.

Page 79

Mise en garde

• La capacité de la vis de fixation

Mur

permettant de supporter une enceinte dépend de la façon dont elle est fixée au mur. Si vos murs sont creux, vissez chaque vis de fixation dans un montant. S’il n’y a aucun montant, ou si les murs

5 à 10 mm

sont pleins, utilisez des fixations murales adéquates. Utilisez des vis dont la tête a un diamètre de 9 mm maximum et un diamètre de la partie lisse de la tige de 4 mm maximum. Pour les murs creux, utilisez un détecteur de câbles/canalisations pour vérifier la présence éventuelle de câbles d’alimentation ou de canalisations d’eau avant d’effectuer des percements.

• Laissez un espace de 5 à 10 mm entre le mur et la base de la tête de la vis, comme indiqué (Nous vous recommandons de consulter un professionnel de l’installation domestique).

Vivez une expérience cinématographique à domicile

Enceintes surround arrière gauche et

droite

(SKB-590)

Ces enceintes renforcent encore plus le réalisme du son surround et améliorent la localisation du son derrière l’auditeur. Placez-les derrière l’auditeur 60 à 100 cm environ audessus du niveau des oreilles.

e Subwoofer (SKW-591)

Le subwoofer gère les graves du canal chargé des effets LFE (effets basse fréquence) et les graves des enceintes satellites lorsqu’un crossover est spécifié. Le volume et la qualité des sons graves émis par le subwoofer dépendent de sa position, de la forme de la pièce où le système est installé et de votre position d’écoute. En général, il est possible d’obtenir un bon son grave en installant le subwoofer dans un coin situé devant l’auditeur ou à environ un tiers de la largeur du mur (cf. illustration).

eba

Branchement des enceintes

Précautions concernant le branchement des enceintes

Lisez ce qui suit avant de brancher vos enceintes :

•

Éteignez votre récepteur avant d’effectuer les branchements.

•

Faites très attention à respecter la polarité des câbles de vos enceintes. Ne branchez les bornes positives (+) que sur les bornes positives (+) et les bornes négatives (–) que sur les bornes négatives (–). Si les enceintes sont branchées de façon incorrecte, le son sera déphasé et ne semblera pas naturel.

• Veillez à ne pas mettre ne pas mettre les fils positifs et négatifs en court-circuit. Vous risqueriez d’endommager votre amplificateur.

Remarque

• Lorsque vous branchez les enceintes avant hautes G/D, effectuez la préparation du branchement d’une manière séparée, ou utilisez les enceintes surround arrière G/D.

Subwoofer

amplifié

Enceinte

avant droite

Enceinte

avant gauche

Grâce au Home Cinema, vous pouvez profiter d’un son surround très réaliste à votre domicile — comme si vous étiez dans une salle de cinéma ou de concert.

a Enceintes avant gauche et droite (SKF-591)

Elles doivent être positionnées face à l’auditeur, à la hauteur des oreilles et être situées à distance égale du téléviseur. Orientez-les légèrement vers l’intérieur de manière à créer un triangle avec l’auditeur.

b Enceinte centrale (SKC-591N/SKC-591)

Positionnez-la à proximité de votre téléviseur (de préférence dessus), face à vous, à la hauteur des oreilles ou à la même hauteur que les enceintes avant gauche et droite.

c Enceintes surround gauche et droite (SKR-590)

Placez-les sur les côtés de l’auditeur, ou légèrement derrière lui, 60 à 100 cm environ au-dessus du niveau des oreilles. Idéalement, elles doivent se situer à égale distance de l’auditeur.

Position angulaire

1/3 de la position murale

Fr-3

À l’aide du câble RCA fourni, branchez la borne LINE INPUT du subwoofer à la prise SUBWOOFER PRE OUT de votre amplituner AV.

Marron

Enceinte surround

arrière gauche

Enceinte centrale

Rouge Blanc

Enceinte surround

arrière droite

Marron clair

Enceinte surround

gauche

Bleu

Enceinte

surround

droite

Vert

Gris

Page 80

Caractéristiques techniques

■ Subwoofer amplifié (SKW-591)

Type Bass-reflex Sensibilité/impédance d’entrée

540 mV/20 kΩ

Puissance de sortie nominale (FTC)

(Nord-américains et brésiliens)

Puissance continue de 120 watts minimum, 4 ohms, utilis ant une fréquence de 100 Hz avec une distorsion harmonique totale maximale de 1%

Puissance de sortie nominale (IEC)

(Asie)

Puissance continue de 120 watts minimum, 4 ohms, utilis ant une fréquence de 100 Hz avec une distorsion harmonique totale maximale de 1%

Distorsion de fréquence 25 Hz à 150 Hz Capacité du coffrage 1,34 pieds cubiques (38 L) Dimensions (L × H × P) 12-1/2" × 18-7/16" × 15-11/16"

Poids 20,1 lbs. (9,1 kg) Entrée audio 1 (mono analogique RCA) Amplificateur Woofer conique de 10" (25 cm) × 1 Alimentation (Nord-américains et brésiliens)

Consommation 35 W Autre Fonction de mise en veille automatique

■ Enceintes avant (SKF-591)

Type Bass-reflex 2 canaux Impédance 6 Ω Puissance d’entrée maximale Sensibilité 84,5 dB/W/m Distorsion de fréquence 55 Hz à 50 kHz Fréquence de crossover 4kHz Capacité du coffrage 0,20 pieds cubiques (5,7 L)

(317,5 mm × 468 mm × 398 mm) (y compris la projection)

120 V CA, 60 Hz

(Asie) CA 220 - 240 V, 50/60 Hz

Protection non-magnétique

130 W

Dimensions (L × H × P) 6-1/8" × 14-7/8" × 6-5/8"

Poids 5,7 lbs. (2,6 kg) Amplificateur Woofer conique OMF de 5" (12 cm) × 1

Borne À ressort et à code couleur Encoche en trou de serrure Grille Fixe Autre Protection non-magnétique

(155 mm × 378 mm × 169 mm) (y compris la grille et la projection)

Dôme équilibré de 1" (2,5 cm) × 1

Disponible

■ Enceinte centrale

SKC-591N (Nord-américains et brésiliens) Type Bass-reflex 2 canaux Impédance 6 Ω Puissance d’entrée maximale Sensibilité 86 dB/W/m Distorsion de fréquence 65 Hz à 50 kHz Fréquence de crossover 6kHz Capacité du coffrage 0,10 pieds cubiques (2,8 L) Dimensions (L × H × P) 16-9/16" × 4-1/2" × 4-11/16"

Poids 5,1 lbs. (2,3 kg) Amplificateur Woofer conique de 3-1/4" (8 cm) × 2

Borne À ressort et à code couleur Encoche en trou de serrure Grille Fixe Autre Protection non-magnétique

SKC-591 (Asie) Type Bass-reflex 2 canaux Impédance 6 Ω Puissance d’entrée maximale Sensibilité 86 dB/W/m Distorsion de fréquence 65 Hz à 50 kHz Fréquence de crossover 6kHz Capacité du coffrage 0,10 pieds cubiques (2,8 L) Dimensions (L × H × P) 16-9/16" × 4-1/2" × 4-11/16"

130 W

(420 mm × 115 mm × 119 mm) (y compris la grille et la projection)

Dôme équilibré de 1" (2,5 cm) × 1

Disponible

130 W

(420 mm × 115 mm × 119 mm) (y compris la grille et la projection)

Poids 5,3 lbs. (2,4 kg) Amplificateur Woofer conique de 3-1/4" (8 cm) × 2

Borne À ressort et à code couleur Encoche en trou de serrure Grille Fixe Autre Protection magnétique

Dôme équilibré de 1" (2,5 cm) × 1

Disponible

■ Enceintes surround/surround arrière

(SKR-590/SKB-590)

Type Large bande à coffrage fermé Impédance 6 Ω Puissance d’entrée maximale Sensibilité 81 dB/W/m Distorsion de fréquence 80 Hz à 20 kHz Capacité du coffrage 0,036 pieds cubiques (1,0 L) Dimensions (L × H × P) 4-1/2" × 9-1/16" × 3-3/4"

Poids 2,2 lbs. (1,0 kg) Amplificateur Cône d’enceinte de 3-1/4" (8 cm) × 1 Borne À ressort et à code couleur Encoche en trou de serrure Grille Fixe Autre Protection non-magnétique

130 W

(115 mm × 230 mm × 96 mm) (y compris la grille et la projection)

Disponible

Les caractéristiques techniques et l’apparence de cet appareil sont susceptibles d’être modifiées sans préavis.

Remarque

Pour enceintes blindées non magnétiques :

Essayez d’éloigner les enceintes de votre téléviseur ou de votre moniteur. Si une décoloration se produit, éteignez votre téléviseur ou votre moniteur, attendez 15 à 30 minutes, puis rallumez le téléviseur ou le moniteur. Ceci active normalement la fonction de démagnétisation, qui neutralise le champ magnétique, supprimant ainsi les effets de décoloration.

SN 29400973

Y1112-1

* 2 9 4 0 0 9 7 3 *

Onkyo HT-r591 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Important Safety Instructions

Safety Information and Introduction

Precautions

Supplied Accessories

Table of Contents

Features

Front & Rear Panels

Front Panel

Display

Rear Panel

Remote Controller

Controlling the AV Receiver

Connections

Connecting the AV Receiver

Connecting Your Speakers

About AV Connections

Connecting Components with HDMI

Connecting Your Components

Connecting a Recording Component

Connecting the Antennas

Connecting the Power Cord

Turning On & Basic Operations

Turning On/Off the AV Receiver

Turning On

Turning Off

Playback

Playing the Connected Component

Controlling Contents of USB Devices

Understanding Icons on the Display

Playing an iPod/iPhone via USB

Playing a USB Device

Listening to AM/FM Radio

Using Basic Functions

Using the Automatic Speaker Setup

Using the Listening Modes

Using the Home Menu

Using the Sleep Timer

Setting the Display Brightness

Displaying Source Information

Changing the Input Display

Using the Music Optimizer

Muting the AV Receiver

Using Headphones

Recording

Advanced Operations

On-screen Setup

Common Procedures in Setup Menu

Setup menu items

HDMI Input

Component (Component Video Input)

Digital Audio (Digital Audio Input)

Sp Config (Speaker Configuration)

Sp Distance (Speaker Distance)

Level Cal (Level Calibration)

Audio Adjust

Source Setup

Hardware

HDMI Setup

Using the Audio Settings

iPod/iPhone Playback via Onkyo Dock

Using the Onkyo Dock

Controlling Other Components

Controlling Your iPod/iPhone

Controlling Other Onkyo Components

Preprogrammed Remote Control Codes

Entering Remote Control Codes

Resetting the REMOTE MODE Buttons

Resetting the Remote Controller

Controlling Other Components

Appendix

Troubleshooting

Connection Tips and Video Signal Path

About HDMI

USB Features

License and Trademark Information

Specifications