Onkyo HT-R590 User Manual 2

Download

Page 1

Contents

AV Receiver

HT-R590

Instruction Manual

Introduction ...................................2

Connections.................................11

Turning On & Basic Operations

Advanced Operations .................34

Controlling Other Components

......18

....45

Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference.

Appendix......................................50

Page 2

Introduction

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand,

PORTABLE CART WARNIN

tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

S3125A

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to

persons. The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

AVIS

RISQUE DE CHOC ELECTRIQUE

NE PAS

OUVRIR

15. Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions:

A. When the power-supply cord or plug is damaged, B. If liquid has been spilled, or objects have fallen

into the apparatus,

C. If the apparatus has been exposed to rain or water, D. If the apparatus does not operate normally by

following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation,

E. If the apparatus has been dropped or damaged in

any way, and

F. When the apparatus exhibits a distinct change in

performance this indicates a need for service.

16. Object and Liquid Entry Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus. Don’t put candles or other burning objects on top of this unit.

17. Batteries Always consider the environmental issues and follow local regulations when disposing of batteries.

18. If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is adequate ventilation. Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a flue-like gap for warm air to escape. The temperature protection operates if the apparatus attain an abnormal high temperature. The apparatus cannot operate until it has cooled down.

Page 3

Precautions

1. Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder.

2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact your Onkyo dealer.

3. Care—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Don’t use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel lettering.

4. Power WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY. AC outlet voltages vary from country to country. Make sure that the voltage in your area meets the voltage requirements printed on the unit’s rear panel (e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).

The power cord plug is used to disconnect this unit from the AC power source. Make sure that the plug is readily operable (easily accessible) at all times.

Pressing the [ON/STANDBY] button to select Standby mode does not fully disconnect from the mains. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

5. Preventing Hearing Loss Caution

Excessive sound pressure from earphones and headphones can cause hearing loss.

6. Batteries and Heat Exposure Warning

Batteries (battery pack or batteries installed) shall not be exposed to excessive heat as sunshine, fire or the like.

7. Never Touch this Unit with Wet Hands—Never handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by your Onkyo dealer.

8. Handling Notes

• If you need to transport this unit, use the original

packaging to pack it how it was when you originally bought it.

• Do not leave rubber or plastic items on this unit for

a long time, because they may leave marks on the case.

• This unit’s top and rear panels may get warm after

prolonged use. This is normal.

• If you do not use this unit for a long time, it may not

work properly the next time you turn it on, so be sure to use it occasionally.

For U.S. models

FCC Information for User CAUTION:

The user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For Canadian Models

NOTE: THIS CLASS B DIGITAL APPARATUS

COMPLIES WITH CANADIAN ICES-003. For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Modèle pour les Canadien

REMARQUE: CET APPAREIL NUMÉRIQUE DE

LA CLASSE B EST CONFORME À LA NORME NMB003 DU CANADA.

Sur les modèles dont la fiche est polarisée:

ATTENTION: POUR ÉVITER LES CHOCS

ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

Page 4

Supplied Accessories

Make sure you have the following accessories:

Indoor FM antenna (➔ page 17)

AM loop antenna (➔ page 17)

Power cord (Brazilian models) (➔ page 17)

Speaker setup microphone (➔ page 24)

Remote controller (RC-799M) and two batteries (AA/R6) (➔ page 4)

(Note for China: The battery for the remote controller is not supplied for this unit.)

In catalogs and on packaging, the letter at the end of the product name indicates the color. Specifications and operations are the same regardless of color.

■ Installing the batteries

Note

• If the remote controller doesn’t work reliably, try replacing the batteries.

• Don’t mix new and old batteries or different types of batteries.

• If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion.

• Remove expired batteries as soon as possible to prevent damage from leakage or corrosion.

Batteries (AA/R6)

■ Aiming the remote controller

To use the remote controller, point it at the AV receiver’s remote control sensor, as shown below.

Remote control sensor

AV receiver

Approx. 16 ft. (5 m)

Page 5

Contents

Introduction

Important Safety Instructions ......................................... 2

Precautions....................................................................... 3

Supplied Accessories...................................................... 4

Features ............................................................................ 6

Front & Rear Panels......................................................... 7

Front Panel..................................................................... 7

Display............................................................................ 8

Rear Panel ..................................................................... 9

Remote Controller.......................................................... 10

Controlling the AV Receiver ......................................... 10

Connections

Connecting the AV Receiver ......................................... 11

Connecting Your Speakers .......................................... 11

About AV Connections ................................................. 13

Connecting Components with HDMI ............................ 14

Connecting Your Components ..................................... 15

Connecting Onkyo u Components ............................ 16

Connecting a Recording Component ........................... 16

Connecting Antenna..................................................... 17

Connecting the Power Cord ......................................... 17

Turning On & Basic Operations

Turning On/Off the AV Receiver ................................... 18

Turning On ................................................................... 18

Turning Off ................................................................... 18

Playback.......................................................................... 19

Playing the Connected Component.............................. 19

Controlling Contents of USB Devices........................... 19

Understanding Icons on the Display............................. 20

Playing iPod/iPhone via USB ....................................... 20

Playing USB Device ..................................................... 21

Listening to AM/FM Radio ............................................ 21

Using Basic Functions .................................................. 24

Using the Automatic Speaker Setup ............................ 24

Using the Listening Modes ........................................... 27

Using the Home Menu.................................................. 31

Using the Sleep Timer.................................................. 31

Setting the Display Brightness ..................................... 32

Displaying Source Information ..................................... 32

Changing the Input Display .......................................... 32

Using the Music Optimizer ........................................... 32

Muting the AV Receiver................................................ 33

Using Headphones....................................................... 33

Recording ..................................................................... 33

Controlling Other Components

iPod/iPhone Playback via Onkyo Dock ........................45

Using the Onkyo Dock.................................................. 45

Controlling Your iPod/iPhone .......................................45

Controlling Other Onkyo Components ........................ 47

Preprogrammed Remote Control Codes ......................47

Entering Remote Control Codes................................... 47

Remote Control Codes for Onkyo Components

Connected via u...................................................... 47

Resetting REMOTE MODE Buttons ............................. 48

Resetting the Remote Controller ..................................48

Controlling Other Components .....................................48

Appendix

Troubleshooting .............................................................50

Connection Tips and Video Signal Path ...................... 54

USB Features.................................................................. 55

About HDMI..................................................................... 56

Using an RIHD-compatible TV, Player, or Recorder ... 57

Specifications ................................................................. 59

To reset the AV receiver to its factory defaults, turn it on and, while holding down VCR/DVR, press

8 ON/STANDBY (➔ page 50).

Advanced Operations

Advanced Setup ............................................................. 34

On-screen Setup Menus .............................................. 34

Common Procedures in Setup Menu ........................... 34

HDMI Input ................................................................... 35

Component (Component Video Input).......................... 35

Digital Audio (Digital Audio Input)................................. 35

Sp Config (Speaker Configuration) .............................. 36

Sp Distance (Speaker Distance) ..................................37

Level Cal (Level Calibration) ........................................ 37

Audio Adjust ................................................................. 37

Source Setup................................................................ 39

Hardware...................................................................... 41

HDMI Setup.................................................................. 42

Using the Audio Settings .............................................. 43

Page 6

Features

Amplifier

• 130 Watts/Channel @ 6 ohms

• 130 Watts/Channel @ 6 ohms (IEC)

• 160 Watts/Channel @ 6 ohms (JEITA)

• Optimum Gain Volume Circuitry

• H.C.P.S. (High Current Power Supply) Massive High Power Transformer

Processing

• HDMI (Audio Return Channel, 3D, DeepColor, x.v.Color*1, Lip Sync, DTS*2-HD Master Audio, DTSHD High Resolution Audio, Dolby TrueHD Digital Plus, DSD and Multi-CH PCM)

• Dolby Pro Logic IIz

• Non-Scaling Configuration

• A-Form Listening Mode Memory

• Direct Mode

• Music Optimizer

for Compressed Digital Music files

• 192 kHz/24-bit D/A Converters

• Powerful and Highly Accurate 32-bit Processing DSP

Connections

• 4 HDMI*5 Inputs and 1 Output

• Onkyo p for System Control

• 4 Digital Inputs (2 Optical/2 Coaxial)

• Component Video Switching (2 Inputs/1 Output)

• Banana Plug-Compatible Speaker Posts

• Front-Panel USB Input for Memory Devices and iPod®/iPhone® models

Miscellaneous

• 40 FM/AM Presets

• Audyssey 2EQ

• Audyssey Dynamic EQ

• Audyssey Dynamic Volume listening level and dynamic range

• Crossover Adjustment (40/50/60/70/80/90/100/120/150/200 Hz)

• A/V Sync Control Function (up to 400 ms)

• Auto Standby Function

• On-Screen Display via HDMI

to correct room acoustic problems

for loudness correction

to maintain optimal

, Dolby

“x.v.Color” is a trademark of Sony Corporation.

Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide patents issued & pending. DTS and the Symbol are registered trademarks, & DTS-HD, DTS-HD Master Audio, and the DTS logos are trademarks of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the double-D symbol are trademarks of Dolby Laboratories.

Music Optimizer™ is a trademark of Onkyo Corporation.

“HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.”

(Asian models)

The AV receiver does not support banana plugs.

iPhone, iPod, iPod classic, iPod nano, iPod shuffle, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance.

Manufactured under license from Audyssey Laboratories™, Inc. U.S. and foreign patents pending. Audyssey 2EQ Audyssey Dynamic EQ are registered trademarks of Audyssey Laboratories, Inc.

and Audyssey Dynamic Volume®

Page 7

Front & Rear Panels

Front Panel

(North American and Brazilian models)

(Asian models)

egfhijklmn

t u

The page numbers in parentheses show where you can find the main explanation for each item.

a 8 ON/STANDBY button (18) b HDMI THRU indicator (42) c SUBWOOFER LEVEL buttons (43) d Remote control sensor (4) e LISTENING MODE buttons (27) f Display (8) g DIMMER button (North American and Brazilian

models) (32)

h MEMORY button (22) i TUNING MODE button (21) j DISPLAY button (32) k SETUP button (34)

l TUNING, PRESET (21 to 22), arrow and ENTER

buttons

m RETURN button n MASTER VOLUME control (19) o MUSIC OPTIMIZER button (32, 44) p PHONES jack (33) q TONE and Tone Level buttons (43) r Input selector buttons (19) s AUX INPUT AUDIO and VIDEO jacks (15, 33) t USB port (15) u SETUP MIC jack (24) v RT/PTY/TP button (Asian models) (23)

Page 8

Display

ab ef

For detailed information, see the pages in parentheses.

a HDMI input indicator b Listening mode and format indicators (27, 32) c Audyssey indicator (24, 39)

Dynamic EQ indicator (39) Dynamic Vol indicator (39)

d Tuning indicators (21)

e RDS indicator (Asian models) (22) f SLEEP indicator (31) g MUTING indicator (33) h Message area

Page 9

Rear Panel

(North American and Asian models)

a b c

h

(Brazilian models)

i j

d

e

f

g

a DIGITAL IN COAXIAL and OPTICAL jacks b COMPONENT VIDEO IN and OUT jacks c HDMI IN and OUT jacks d FM ANTENNA jack and AM ANTENNA terminal e SUBWOOFER PRE OUT jack f SPEAKERS terminals

(FRONT, CENTER, SURROUND, SURROUND BACK or FRONT HIGH)

g Power cord (North American and Asian models)

h u REMOTE CONTROL jack i Composite video and analog audio jacks

(BD/DVD IN, VCR/DVR IN and OUT, CBL/SAT IN, GAME IN, TV/CD IN)

j MONITOR OUT V jack k AC INLET (Brazilian models)

See “Connecting the AV Receiver” for connection (➔ pages 11 to 17).

Page 10

Remote Controller

Controlling the AV Receiver

To control the AV receiver, press RECEIVER to select Receiver mode.

You can also use the remote controller to control Onkyo Blu-ray Disc/DVD player, CD player, and other components. See “Entering Remote Control Codes” for more details (➔ page 47).

For detailed information, see the pages in parentheses.

a 8 button (18) b REMOTE MODE/INPUT SELECTOR buttons (19,

47 to 48)

c TONE and Tone Level buttons (43) d Arrow q/w/e/r and ENTER buttons e SETUP button (34) f LISTENING MODE buttons (27) g DIMMER button (32) h DISPLAY button (32) i MUTING button (33) j VOL q/w button (19) k RETURN button l HOME button (31, 43) m SLEEP button (31)

■ Controlling the tuner

To control the AV receiver’s tuner, press AM or FM.

a Arrow q/w buttons (21) b D.TUN button (22) c DISPLAY button (22) d CH +/– button (22) e Number buttons (22)

SP A/B is not used for this model.

Page 11

Connections

Connecting the AV Receiver

Connecting Your Speakers

Connecting the Speaker Cables

The following illustration shows which speaker should be connected to each pair of terminals. If you’re using only one surround back speaker, connect it to the SURROUND BACK or FRONT HIGH L terminals.

Surround back/

front high

right

Surround back/

front high

left

Surround

right

Surround

left Center

Front right Front left

Tip

• You can specify whether surround back or front high speakers are connected in the “Sp Config (Speaker Configuration)” menu (➔ page 36) or during Audyssey 2EQ

Room Correction and Speaker Setup (➔ page 24).

■ Screw-type speaker terminals

Strip 1/2" to 5/8" (12 to 15 mm) of insulation from

1/2" to 5/8" (12 to 15 mm)

the ends of the speaker cables, and twist the bare wires tightly, as shown.

■ Banana Plugs (excluding Asian models)

• If you are using banana plugs, tighten the speaker terminal before inserting the banana plug.

• Do not insert the speaker code directly into the center hole of the speaker terminal.

Page 12

Speaker Configuration

The following table indicates the channels you should use depending on the number of speakers that you have.

No matter how many speakers you use, a powered subwoofer is recommended for a really powerful and solid bass. To get the best from your surround sound system, you need to set the speaker settings automatically (➔ page 24) or manually (➔ page 36).

Number of channels 2345677

Front speakers ✔✔✔✔✔✔✔ Center speaker ✔ ✔✔✔✔ Surround speakers ✔✔✔✔✔ Surround back speaker Surround back speakers Front high speakers

*1*2

✔

• Don’t connect more than one cable to each speaker terminal. Doing so may damage the AV receiver.

• Don’t connect one speaker to several terminals.

Using a Powered Subwoofer

If you’re using only one surround back speaker, connect it to the SURROUND BACK or FRONT HIGH L terminals.

Front high and surround back speakers cannot be used at the same time.

Speaker Connection Precautions

Read the following before connecting your speakers:

• You can connect speakers with an impedance of between 6 and 16 ohms. If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in amp protection circuit may be activated.

• Disconnect the power cord from the wall outlet before making any connections.

• Read the instructions supplied with your speakers.

• Pay close attention to speaker wiring polarity. In other words, connect positive (+) terminals only to positive (+) terminals, and negative (–) terminals only to negative (–) terminals. If you get them the wrong way around, the sound will be out of phase and will sound unnatural.

• Unnecessarily long, or very thin speaker cables may affect the sound quality and should be avoided.

• Be careful not to short the positive and negative wires. Doing so may damage the AV receiver.

• Make sure the metal core of the wire does not have contact with the AV receiver’s rear panel. Doing so may damage the AV receiver.

To find the best position for your subwoofer, while playing a movie or some music with good bass, experiment by placing your subwoofer at various positions within the room, and choose the one that provides the most satisfying results.

Tip

• If your subwoofer is unpowered and you’re using an external amplifier, connect the subwoofer pre out jack to an input on the amplifier.

LINE INPUT

Powered subwoofer

Corner position

1/3 of wall

position

Page 13

About AV Connections

Connected image with AV components

HDMI cable Other cables

: Video & Audio

AV receiverAV receiver

TV, projector, etc.

Blu-ray Disc/

DVD player

Game console

TV, projector, etc.

Blu-ray Disc/

DVD player

• Before making any AV connections, read the manuals supplied with your AV components.

• Don’t connect the power cord until you’ve completed and double-checked all AV connections.

• Push plugs in all the way to make good connections (loose connections can cause noise or malfunctions).

• To prevent interference, keep audio and video cables away from power cords and speaker cables.

AV Cables and Jacks

Signal Cable Jack Description

Video and Audio

HDMI HDMI connections can carry digital video and audio.

HDMI

: Video : Audio

Game console

Right!

Wrong!

Video Component video Component video separates the luminance (Y) and color

Composite video Composite video is commonly used on TVs, VCRs, and

Audio Optical digital

audio

Green

Blue

Red

Yellow

OPTICAL

difference signals (P quality (some TV manufacturers label their component video sockets slightly differently).

other video equipment. Optical digital connections allow you to enjoy digital

sound such as PCM

B, PR), providing the best picture

, Dolby Digital or DTS. The audio

quality is the same as coaxial.

Coaxial digital audio

Orange

Coaxial digital connections allow you to enjoy digital

sound such as PCM

, Dolby Digital or DTS. The audio

quality is the same as optical.

Analog audio (RCA)

Available sampling rate for PCM input signal is 32/44.1/48/88.2/96 kHz. Even 176.4/192 kHz is effective in case of the HDMI

White

Red

Analog audio connections (RCA) carry analog audio.

connection.

Note

• The AV receiver does not support SCART plugs.

• The AV receiver’s optical digital jacks have shutter-type covers that open when an optical plug is inserted and close when it’s removed. Push plugs in all the way.

Caution

• To prevent shutter damage, hold the optical plug straight when inserting and removing.

Page 14

Connecting Components with HDMI

VCR or DVD recorder/Digital Video Recorder

Game console

Satellite/cable set-top box, etc. Blu-ray Disc/DVD player

TV, projector, etc.

Connect your components to the appropriate jacks. The default input assignments are shown below.

✔: Assignment can be changed (➔ page 35).

Jack Components Assignable

Input HDMI IN1 Blu-ray Disc/DVD player ✔

HDMI IN2 VCR or DVD recorder/Digital Video Recorder ✔ HDMI IN3 Satellite/cable set-top box, etc. ✔ HDMI IN4 Game console ✔

Output HDMI OUT TV, projector, etc.

See also:

• “Connection Tips and Video Signal Path” (➔ page 54)

• “About HDMI” (➔ page 56)

• “Using an RIHD-compatible TV, Player, or Recorder” (➔ page 57)

■ Audio return channel (ARC) function

Audio return channel (ARC) function enables an HDMI capable TV to send the audio stream to the HDMI OUT of the AV receiver (➔ page 42).

• To use ARC function, you must select the TV/CD input selector, your TV must support ARC function and “HDMI

Ctrl (RIHD)” is set to “On” (➔ page 42).

Tip

• To listen to audio received by the HDMI IN jacks through your TV’s speakers: – Set the “HDMI Ctrl (RIHD)” setting to “On” for an p-compatible TV. – Set the “Audio TV Out” setting to “On” (➔ page 42) when the TV is not compatible with p or the “HDMI Ctrl (RIHD)”

setting to “Off”. – Set your Blu-ray Disc/DVD player’s HDMI audio output setting to PCM. – To listen to TV audio through the AV receiver, see “Connecting Your Components” (➔ page 15).

Note

• When listening to an HDMI component through the AV receiver, set the HDMI component so that its video can be seen on the TV screen (on the TV, select the input of the HDMI component connected to the AV receiver). If the TV power is off or the TV is set to another input source, this may result in no sound from the AV receiver or the sound may be cut off.

• When the “Audio TV Out” setting is set to “On” (➔ page 42) to hear from your TV’s speakers, by controlling the AV receiver’s volume, the sound will be output from the AV receiver’s speakers, too. When the (➔ page 42) to hear from speakers of p-compatible TV, by controlling the AV receiver’s volume, the AV receiver’s speakers will produce sound while the TV’s speakers are muted. To stop the AV receiver’s speakers producing sound, change the settings, change your TV’s settings, or turn down the AV receiver’s volume.

“HDMI Ctrl (RIHD)” setting is set to “On”

Page 15

Connecting Your Components

The on-screen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver’s display when changing settings.

A CB

ED F

Connect your components to the appropriate jacks. The default input assignments are shown below.

✔: Assignment can be changed (➔ page 35).

No. Jack Components Assignable

AUX INPUT

USB, AUX INPUT VIDEO

USB

DIGITAL IN OPTICAL 1 (GAME) Game console ✔

COMPONENT

VIDEO

MONITOR OUT TV, projector, etc.

BD/DVD IN Blu-ray Disc/DVD player VCR/DVR IN VCR, DVD recorder/Digital Video Recorder,

CBL/SAT IN Satellite/cable set-top box, etc. GAME IN Game console, RI dock TV/CD IN TV, CD player, cassette tape deck, MD, CD-R,

VIDEO AUDIO L/R

2 (TV/CD) TV, CD player ✔

COAXIAL 1 (BD/DVD) Blu-ray Disc/DVD player ✔

2 (CBL/SAT) Satellite/cable set-top box, RI dock, etc. ✔ IN 1 (BD/DVD) Blu-ray Disc/DVD player, RI dock ✔ IN 2 (CBL/SAT) Satellite/cable set-top box, RI dock, etc. ✔ OUT TV, projector, etc.

Camcorder, etc

iPod/iPhone (video playback) iPod/iPhone, MP3 player, USB flash drive

RI dock

Turntable

, RI dock

When USB input is selected, you can input video signals from the AUX INPUT VIDEO jack. Video signals input from AUX INPUT VIDEO will be output from the MONITOR OUT jack.

Do not connect the AV receiver’s USB port to a USB port on your computer. Music on your computer cannot be played through the AV receiver in this way.

Connect a turntable (MM) that has a phono preamp built-in. If your turntable (MM) doesn’t have it, you’ll need a commercially available phono preamp. If your turntable has a moving coil (MC) type cartridge, you’ll need a commercially available MC head amp or MC transformer as well as a phono preamp. See your turntable’s manual for details.

• With connection D, you can enjoy Dolby Digital and DTS.

• If your Blu-ray Disc/DVD player has both the main stereo and multichannel outputs, be sure to connect the main stereo output using connection F.

■ How to record the video

See “Recording” to make a connection for video recording (➔ page 33).

Page 16

Connecting Onkyo u Components

Make sure that each Onkyo component is

connected with an analog audio cable (connection F in the hookup examples) (➔ page 15).

Make the u connection (see the illustration).

If you’re using an RI Dock or cassette tape deck,

change the Input Display (➔ page 32).

With u (Remote Interactive), you can use the following special functions:

■ System On/Auto Power On

When you start playback on a component connected via u, if the AV receiver is on Standby, it will

automatically turn on and select that component as the input source.

■ Direct Change

When playback is started on a component connected via u, the AV receiver automatically selects that

component as the input source.

■ Remote Control

You can use the AV receiver’s remote controller to control your other u-capable Onkyo components,

pointing the remote controller at the AV receiver’s remote control sensor instead of the component. You must enter the appropriate remote control code first (➔ page 47).

ANALOG

e.g., CD player

e.g., DVD player

Note

•Use only u cables for u connections. u cables are supplied with Onkyo players (DVD, CD, etc.).

• Some components have two u jacks. You can connect either one to the AV receiver. The other jack is for connecting

additional u-capable components.

• Connect only Onkyo components to u jacks. Connecting other manufacturer’s components may cause a malfunction.

• Some components may not support all u functions. Refer to the manuals supplied with your other Onkyo components.

AUDIO OUT

ANALOG

AUDIO OUT

Connecting a Recording Component

See “Recording” on the recording (➔ page 33).

AUDI O

VCR, DVD recorder,

cassette tape deck,

CDR, MD recorder, etc.

VIDEO

Note

• The AV receiver must be turned on for recording. Recording is not possible while it’s in Standby mode.

• If you want to record directly from your TV or playback VCR to the recording VCR without going through the AV receiver, connect the TV/VCR’s audio and video outputs directly to the recording VCR’s audio and video inputs. See the manuals supplied with your TV and VCR for details.

• Video signals connected to composite video inputs can be recorded only via composite video outputs. If your TV/VCR is connected to a composite video input, the recording VCR must be connected to a composite video output.

• The surround sound and DSP listening modes cannot be recorded.

• Copy-protected Blu-ray discs and DVDs cannot be recorded.

• Sources connected to a digital input cannot be recorded. Only analog inputs can be recorded.

• DTS signals will be recorded as noise, so don’t attempt analog recording of DTS CDs or LDs.

Page 17

Connecting Antenna

This section explains how to connect the supplied indoor FM antenna and AM loop antenna. The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use

the tuner.

Caution

• Be careful that you don’t injure yourself when using thumbtacks.

Push. Insert wire. Release.

Assembling the AM loop antenna

North American and Brazilian models

Insert the plug fully into the jack.

Asian models

Insert the plug fully into the jack.

Thumbtacks, etc.

Indoor FM antenna (supplied)AM loop antenna (supplied)

Note

• Once your AV receiver is ready for use, you’ll need to tune into a radio station and position the antenna to achieve the best possible

reception.

• Keep the AM loop antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.

Tip

• If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead.

• If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor

AM antenna.

Connecting the Power Cord

(Brazilian models)

Connect the supplied power cord to the AV receiver’s AC INLET.

To AC wall outlet

Plug the power cord into an AC wall outlet.

Note

• Before connecting the power cord, connect all of your speakers and AV components.

• Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit.

• Do not use a power cord other than the one supplied with the AV receiver. The supplied power cord is designed exclusively for use with the AV receiver and should not be used with any other equipment.

• Never disconnect the power cord from the AV receiver while the other end is still plugged into a wall outlet. Doing so may cause an electric shock. Always disconnect the power cord from the wall outlet first, and then the AV receiver.

Page 18

Turning On & Basic Operations

Turning On/Off the AV Receiver

8ON/STANDBY

RECEIVER

Turning On

Press 8 ON/STANDBY on the front panel.

Press RECEIVER followed by 8 on the remote controller.

The AV receiver comes on, the display lights.

Turning Off

Press 8 ON/STANDBY on the front panel.

Press RECEIVER followed by 8 on the remote controller.

The AV receiver will enter standby mode. To prevent any loud surprises when you turn on the AV receiver, always turn down the volume before you turn it off.

Tip

• See “Auto Standby” about a power management setting (➔ page 41).

Page 19

Playback

The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver’s display when changing settings.

This section describes the procedure using the remote controller unless otherwise specified.

Playing the Connected Component

■ Operating with the remote controller

Press RECEIVER followed by INPUT

SELECTOR.

Start playback on the source component.

See also:

• “Playing iPod/iPhone via USB” (➔ page 20)

• “Playing USB Device” (➔ page 21)

• “Listening to AM/FM Radio” (➔ page 21)

• “iPod/iPhone Playback via Onkyo Dock” (➔ page 45)

• “Controlling Other Onkyo Components” (➔ page 47)

To adjust the volume, use VOL q/w.

Select a listening mode and enjoy!

See also:

• “Using the Listening Modes” (➔ page 27)

• “Audyssey” (➔ page 39)

■ Operating on the AV receiver

Use the input selector buttons to select the input

source.

Start playback on the source component.

To adjust the volume, use the MASTER VOLUME

control.

Select a listening mode and enjoy!

Controlling Contents of USB Devices

See “Controlling Other Onkyo Components” about the operation of other components (➔ page 47).

Press USB

first.

a b

c d

e f g

TOP MENU

This button displays the top menu for each media or service.

q/w and ENTER

These buttons navigate through the menus.

e/r

This button cycles through pages.

PLAYLIST e/r

In Standard Mode (iPod/iPhone), this button selects playlists.

This button starts playback.

This button selects the beginning of the current song. Pressing this button twice selects the previous song.

This button fast-reverses the current song.

This button pauses playback.

You can toggle between the playback screen and the list screen during playback.

REPEAT

Press this button repeatedly to cycle through the repeat modes. To cancel repeat playback, press REPEAT repeatedly until you select Off.

DISPLAY

This button switches between song informations.

CH +/–

In Standard Mode (iPod/iPhone), this button selects albums.

RETURN

This button returns to the previous menu.

k l

m n

o p

Page 20

This button selects the next song.

This button fast-forwards the current song.

This button stops playback.

MODE

You can switch between Standard Mode and Extended Mode during iPod/iPhone playback.

RANDOM

This button performs random playback. All of the songs in the current folder will be played in random order. When all of the songs in the folder have been played once, they’ll all be played again in a different random order. To cancel random playback, press this button again.

Note

• The buttons you can use will differ depending on the devices and media used for playback.

Understanding Icons on the Display

This section describes icons that appear on the display during media playback.

Displayed Icons

Icon Description

Folder

Track

Playback

Pause

Fast Forward

Fast Reverse

Playing iPod/iPhone via USB

The on-screen navigation menus appear only on a TV that is connected to the HDMI OUT.

This section explains how to play music files on the iPod/iPhone. Compatible iPod/iPhone models Made for: iPod touch (1st, 2nd, 3rd and 4th generation), iPod classic, iPod with video, iPod nano (1st, 2nd, 3rd, 4th, 5th and 6th generation), iPhone 4, iPhone 3GS, iPhone 3G, iPhone

Press USB to select the “USB” input.

Connect the USB cable that comes with the

iPod/iPhone to the USB port at the front of the AV receiver.

While reading the contents of your iPod/iPhone, the message “Connecting...” appears on the display.

Press MODE to switch to Extended Mode.

A list of your iPod/iPhone model’s contents appears. Use q/w to open a folder, and then press ENTER.

Tip

• With the default settings, iPod/iPhone is operated in Standard Mode.

• Pressing MODE again switches back to Standard Mode.

• When you disconnect the iPod/iPhone, the AV receiver stores the mode. This means that if you disconnect when in Extended Mode, the AV receiver will start in Extended Mode when you next connect the iPod/iPhone.

• You can also use the q/w, ENTER and TUNING MODE buttons on the front panel. TUNING MODE allows you to switch modes.

• When connecting your iPod/iPhone with a USB cable, we recommend you use an official USB cable from Apple Inc.

Use q/w to select a music file, and press ENTER or

1 to start playback.

Artist

Album

Repeat One Track

Repeat Folder (USB Device)

Repeat

Shuffle

Shuffle Album (iPod/iPhone)

Note

• Do not disconnect the USB device or USB cable that comes with iPod/iPhone to the USB port at the front of the AV receiver, while the message “Connecting...” appears on the display.

Standard Mode control

The content information is not displayed on-screen, but can be operated using the iPod/iPhone or the remote controller (USB).

Note

• The following iPod models are not supported in Standard Mode. These iPod models can only be controlled in Extended Mode. – iPod with video – iPod nano (1st generation)

Page 21

Extended Mode control

The content information is displayed (lists are displayed) on-screen, and you can control the content while looking at the screen.

Top screen list: Playlists, Artists, Albums, Genres, Songs, Composers,

Shuffle Songs, Now Playing

Playing USB Device

The on-screen navigation menus appear only on a TV that is connected to the HDMI OUT.

This section explains how to play music files on a USB device (e.g., USB flash drives and MP3 players). See also:

• “USB Features” (➔ page 55).

Listening to AM/FM Radio

This section describes the procedure using the buttons on the front panel unless otherwise specified.

Using the Tuner

With the built-in tuner you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection.

You can change the frequency steps (➔ page 41).

Press AM or FM to select either “AM” or “FM”.

In this example, FM has been selected.

Band Frequency

Press USB to select the “USB” input.

Plug your USB device into the USB port at the

front of the AV receiver.

While reading the contents of your USB device, the message “Connecting...” appears on the display.

Press ENTER.

A list of the device’s contents appears. To open a folder, use q/w to select it, and then press ENTER.

Use q/w to select a music file, and press ENTER or

1 to start playback.

Note

• If the media you connect is not supported, the message “No Storage” will appear on the display.

• If you connect a USB hard disk drive to the AV receiver’s USB port, we recommend that you use its AC adapter to power it.

• The AV receiver supports USB MP3 players that support the USB Mass Storage Class standard, which allows USB storage devices to be connected to computers without the need for special drivers or software. Note that not all USB MP3 players support the USB Mass Storage Class standard. Refer your USB MP3 player’s instruction manual for details.

• Protected WMA music files on an MP3 player cannot be played.

• Onkyo accepts no responsibility whatsoever for the loss or damage to data stored on a USB mass storage device when that device is used with the AV receiver. We recommend that you back up your important music files beforehand.

• MP3 players containing music files that are managed with special music software are not supported.

• Operation with all USB mass storage devices including the ability to power them is not guaranteed.

• Do not connect your USB mass storage device via a USB hub. The USB mass storage device must be connected directly to the AV receiver’s USB port.

• If the USB mass storage device contains a lot of data, the AV receiver make take a while to read it.

• USB memory devices with security functions cannot be played.

• Do not disconnect the USB device or USB cable that comes with iPod/iPhone to the USB port at the front of the AV receiver, while the message “Connecting...” appears on the display.

(Actual display depends on the country.)

Tuning into Radio Stations

■ Auto tuning mode

Press TUNING MODE so that the AUTO indicator

lights on the display.

Press TUNING q/w.

Searching stops when a station is found. When tuned into a station, the TUNED indicator

lights. When tuned into a stereo FM station, the FM STEREO indicator lights on the display, as shown.

FM STEREO

AUTO

TUNED

Tip

• Tuning into weak FM stereo stations

If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to manual tuning mode and listen to the station in mono.

Page 22

■ Manual tuning mode

In manual tuning mode, FM stations will be in mono.

Press TUNING MODE so that the AUTO indicator

goes off on the display.

Press and hold TUNING q/w.

The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time.

■ Tuning into stations by frequency

You can tune into AM and FM stations directly by entering the appropriate frequency.

On the remote controller, press AM or FM to select

“AM” or “FM”, followed by D.TUN.

■ Selecting Presets

To select a preset, use PRESET e/r on the AV

receiver, or the remote controller’s CH +/–.

Tip

• You can also use the remote controller’s number buttons to select a preset directly.

■ Deleting Presets

Select the preset that you want to delete.

See the previous section.

While holding down MEMORY, press TUNING

MODE.

The preset is deleted and its number disappears from the display.

Using RDS (Asian models)

(Actual display depends on the country.)

Within 8 seconds, use the number buttons to enter

the frequency of the radio station.

For example, to tune to 87.5 (FM), press 8, 7, 5. If you have entered the wrong number, you can retry

after 8 seconds.

Presetting AM/FM Stations

You can store a combination of up to 40 of your favorite AM/FM radio stations as presets.

Tune into the AM/FM station that you want to

store as a preset.

See the previous section.

Press MEMORY.

The preset number flashes.

(Actual display depends on the country.)

While the preset number is flashing (about 8

seconds), use PRESET e/r to select a preset from 1 through 40.

Press MEMORY again to store the station or

channel.

The station or channel is stored and the preset number stops flashing. Repeat this procedure for all of your favorite AM/FM radio stations.

RDS works only in areas where RDS broadcasts are available.

When tuned into an RDS station, the RDS indicator lights. When the station is broadcasting text information, the text can be displayed.

■ What is RDS?

RDS stands for Radio Data System and is a method of transmitting data in FM radio signals. It was developed by the European Broadcasting Union (EBU) and is available in most European countries. Many FM stations use it these days. In addition to displaying text information, RDS can also help you find radio stations by type (e.g., news, sport, rock, etc.).

The AV receiver supports four types of RDS information:

PS (Program Service)

When tuned to an RDS station that’s broadcasting PS information, the station’s name will be displayed. Pressing DISPLAY will display the frequency for 3 seconds.

RT (Radio Text)

When tuned to an RDS station that’s broadcasting text information, the text will be shown on the display as described in the next section.

PTY (Program Type)

This allows you to search for RDS radio stations by type (➔ page 23).

TP (Traffic Program)

This allows you to search for RDS radio stations that broadcast traffic information (➔ page 23).

Note

• In some cases, the text characters displayed on the AV receiver may not be identical to those broadcast by the radio station. Also, unexpected characters may be displayed when unsupported characters are received. This is not a malfunction.

• If the signal from an RDS station is weak, RDS data may be displayed intermittently or not at all.

Page 23

■ Displaying Radio Text (RT)

Press RT/PTY/TP once.

The RT information scrolls across the display.

Note

• The message “Waiting” may appear while the AV receiver waits for the RT information.

• If the message “No Text Data” appears on the display, no RT information is available.

■ Finding Stations by Type (PTY)

You can search for radio stations by type.

Press RT/PTY/TP twice.

The current program type appears on the display.

Use PRESET e/r to select the type of program

you want.

See the table shown later in this chapter.

To start the search, press ENTER.

The AV receiver searches until it finds a station of the type you specified, at which point it stops briefly before continuing with the search.

When a station you want to listen to is found, press

ENTER.

If no stations are found, the message “Not Found” appears.

■ Listening to Traffic News (TP)

You can search for stations that broadcast traffic news.

Press RT/PTY/TP three times.

If the current radio station is broadcasting TP (Traffic Program), “[TP]” will appear on the display, and traffic news will be heard as and when it’s broadcast. If “TP” without square brackets appears, this means that the station is not broadcasting TP.

To locate a station that is broadcasting TP, press

ENTER.

The AV receiver searches until it finds a station that’s broadcasting TP.

If no stations are found, the message “Not Found” appears.

RDS program types (PTY)

Type Display

None None News reports News Current affairs Affairs Information Info Sport Sport Education Educate Drama Drama Culture Culture Science and technology Science Varied Varied Pop music Pop M Rock music Rock M Middle of the road music Easy M Light classics Light M Serious classics Classics Other music Other M Weather Weather Finance Finance Children’s programmes Children Social affairs Social Religion Religion Phone in Phone In Travel Travel Leisure Leisure Jazz music Jazz Country music Country National music Nation M Oldies music Oldies Folk music Folk M Documentary Document Alarm test TEST Alarm Alarm!

Page 24

Using Basic Functions

Using the Automatic Speaker Setup

With the supplied calibrated microphone, Audyssey 2EQ® automatically determines the number of speakers connected, their size for purposes of bass management, optimum crossover frequencies to the subwoofer (if present), and distances from the primary listening position. Audyssey 2EQ then removes the distortion caused by room acoustics by capturing room acoustical problems over the listening area in both the frequency and time domain. The result is clear, well-balanced sound for everyone. Audyssey 2EQ can be used with Audyssey Dynamic EQ Audyssey Dynamic Volume® (➔ page 39). Before using this function, connect and position all of your speakers. Audyssey 2EQ offers two ways of measuring: the “Audyssey Quick Start” and “Audyssey 2EQ Full Calibration”.

•“Audyssey Quick Start” uses the measurement from one position to perform the speaker setting only.

•“Audyssey 2EQ Full Calibration” uses the measurement from three positions to correct room response in addition to the speaker setting.

The Quick Start takes 2 minutes and Full Calibration takes about 10 minutes.

Total measurement time varies depending on the number of speakers.

and

Measurement procedure

To create a listening environment in your home theater that all listeners will enjoy, Audyssey 2EQ takes measurements at up to 3 positions within the listening area. Position the microphone at ear height of a seated listener with the microphone tip pointed directly at the ceiling using a tripod. Do not hold the microphone in your hand during measurements as this will produce inaccurate results.

a First measurement position

Also referred to as the Main Listening Position, this refers to the most central position where one would normally sit within the listening environment. Audyssey 2EQ uses the measurements from this position to calculate speaker distance, level, polarity, and the optimum crossover value for the subwoofer.

b Second measurement position

The right side of the listening area.

c Third measurement position

The left side of the listening area.

The distances from position a to b and a to c must be at least 1 meter (3.3 ft.).

acb

: Listening area

Note

• Make the room as quiet as possible. Background noise and Radio Frequency Interference (RFI) can disrupt the room measurements. Close windows, televisions, radios, air conditioners, fluorescent lights, home appliances, light dimmers, or other devices. Silence the cell phone (even if it is not in use) or place it away from all audio electronics.

• The microphone picks up test tones played through each speaker as Audyssey 2EQ Room Correction and Speaker Setup runs.

• Audyssey 2EQ Room Correction and Speaker Setup cannot be performed while a pair of headphones is connected.

a to c: Listening position

Page 25

Turn on the AV receiver and the connected TV.

On the TV, select the input to which the AV receiver is connected.

Set the speaker setup microphone at the Main

Listening Position a, and connect it to the SETUP MIC jack.

SETUP MIC jack

Speaker setup microphone

The speaker setting menu appears.

Note

• The on-screen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver’s display when changing settings.

When you’ve finished making the settings, press

ENTER.

2EQ: Auto Setup

SurrBk/FrontHigh SurrBack

Audyssey

Perform the “Sp Config (Speaker Configuration)” according to your speaker configuration:

–“SurrBk/FrontHigh” (➔ page 36)

Use q/w to select “Audyssey Quick Start” or

“Audyssey 2EQ Full Calibration”.

Press ENTER.

Audyssey 2EQ

Room Correction and Speaker Setup starts. Test tones are played through each speaker as Audyssey 2EQ Room Correction and Speaker Setup runs. This process takes a few minutes. Please

refrain from talking during measurements and do not stand between speakers and the microphone.

Do not disconnect the speaker setup microphone during Audyssey 2EQ Room Correction and Speaker Setup, unless you want to cancel the setup.

If you select “Audyssey Quick Start”, you will go to step 8.

Place the setup microphone at the next position,

and then press ENTER.

Audyssey 2EQ performs more measurements. This takes a few minutes.

When prompted, place the setup microphone at

the next position, and repeat step 6.

Use q/w to select an option, and then press

ENTER.

2EQ: Auto Setup

<- Review Speaker Configuration ->

Subwoofer : Yes Front : Small Center : Small Surround : Small Front High : None Surr Back : Small Surr Back Ch : 2ch Crossover : 100Hz

Save Cancel

Audyssey

The options are:

` Save:

Save the calculated settings and exit Audyssey 2EQ Room Correction and Speaker Setup.

` Cancel:

Cancel Audyssey 2EQ Room Correction and Speaker Setup.

Note

• You can view the calculated settings for the speaker configuration, speaker distances, and speaker levels by

using e/r.

Use q/w to select a target, and use e/r to change

the setting.

After the results of Audyssey 2EQ have been saved, the menu will display the “Audyssey” (➔ page 39), “Dynamic EQ” (➔ page 39), “Dynamic Volume” (➔ page 39) settings.

Note

•When “Audyssey Quick Start” has been used for measurement, “Audyssey” cannot be selected.

• These settings are applied to all input selectors.

Press ENTER.

Disconnect the speaker setup microphone.

Note

• You can cancel Audyssey 2EQ Room Correction and Speaker Setup at any point in this procedure simply by disconnecting the setup microphone.

• Do not connect or disconnect any speakers during Audyssey 2EQ Room Correction and Speaker Setup.

• If the AV receiver is muted, it will be unmuted automatically when Audyssey 2EQ Room Correction and Speaker Setup starts.

• Changes to the room after Audyssey 2EQ Room Correction and Speaker Setup require you run Audyssey 2EQ Room Correction and Speaker Setup again, as room EQ characteristics may have changed.

Page 26

Error Messages

Using a Powered Subwoofer

While Audyssey 2EQ® Room Correction and Speaker Setup is in progress, one of the error messages below may appear.

2EQ: Auto Setup

Ambient noise is too high.

Retry Cancel

Audyssey

Error message

The options are:

` Retry:

Try again.

` Cancel:

Cancel Audyssey 2EQ Room Correction and Speaker Setup.

• Ambient noise is too high.

The background noise is too loud. Remove the source of the noise and try again.

• Speaker matching error!

The number of speakers detected was different from that of the first measurement. Check the speaker connection.

• Writing Error!

This message appears if saving fails. Try saving again. If this message appears after 2 or 3 attempts, contact your Onkyo dealer.

• Speaker Detect Error

This message appears if a speaker is not detected. “No” means that no speaker was detected.

Tip

• See “Speaker Configuration” for appropriate settings (➔ page 12).

If you’re using a powered subwoofer and it outputs very low-frequency sound at a low volume level, it may not be detected by Audyssey 2EQ Room Correction and Speaker Setup.

If the “Subwoofer” appears on the “Review Speaker Configuration” screen as “No”, increase the subwoofer’s volume to the half-way point, set it to its highest crossover frequency, and then try running Audyssey 2EQ Room Correction and Speaker Setup again. Note that if the volume is set too high and the sound distorts, detection issues may occur, so use an appropriate volume level. If the subwoofer has a low-pass filter switch, set it to Off or Direct. Refer to your subwoofer’s instruction manual for details.

Changing the Speaker Setup Manually

You can manually make changes to the settings found during Audyssey 2EQ Room Correction and Speaker Setup.

See also:

• “Sp Config (Speaker Configuration)” (➔ page 36)

• “Sp Distance (Speaker Distance)” (➔ page 37)

• “Level Cal (Level Calibration)” (➔ page 37)

Page 27

Using the Listening Modes

Selecting Listening Modes

See “Listening Modes” for detailed information about the listening modes (➔ page 28).

■ Listening Mode Buttons

Press

RECEIVER first.

MOVIE/TV, MUSIC, GAME

MUSIC

MOVIE/TV

GAME STEREO

MOVIE/TV button

This button selects the listening modes intended for use with movies and TV.

MUSIC button

This button selects the listening modes intended for use with music.

• The Dolby Digital and DTS listening modes can only be selected if your Blu-ray Disc/DVD player is connected to the AV receiver with a digital audio connection (coaxial, optical, or HDMI).

• The listening modes you can select depends on the format of the input signal. To check the format, see “Displaying Source Information” (➔ page 32).

• While a pair of headphones is connected, you can select the following listening modes: Mono, Direct, and Stereo.

GAME button

This button selects the listening modes intended for use with video games.

STEREO button

This button selects the Stereo listening mode and All Channel Stereo listening modes.

About Listening Modes

The AV receiver’s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound.

■ Explanatory Notes

ab c d e

a Front speakers b Center speaker c Surround speakers

d Surround back speakers

e Front high speakers f Subwoofer

Page 28

Input Source

The following audio formats are supported by the listening mode.

A S D

This is mono (monophonic) sound.

This is stereo (stereophonic) sound. Two independent audio signal channels are reproduced through two speakers.

This is 5.1-channel surround sound. This surround system has five main channels of sound and a sixth subwoofer channel (called the point-one channel).

This is 7.1-channel surround sound. This is a further sound enhancement to 5.1 channel sound with two additional speakers that provide greater sound envelopment and more accurate positioning of sounds.

This is DTS-ES surround sound. This surround system can produce a discrete or a matrix-encoded sixth channel from existing DTS 5.1 encoded material.

This is Dolby Digital EX surround sound. This provides a center back surround channel from 5.1-channel sources.

Speaker Layout

The illustration shows which speakers are activated in each channel. See “Sp Config (Speaker Configuration)” for the speaker setup (➔ page 36).

ZXC N

■ Onkyo-Original DSP Listening Modes

Listening Mode Description Input

Orchestra

Or c es t rah

Unplugged

Unp ugg edl

Studio-Mix

Stu io– Mi xd

TV Logic

TV og i cL

Game-RPG

Gam – R P Ge

Game-Action

Gam –Ac t i o ne

Game-Rock

Gam –Ro cke

Game-Sports

Gam – S p or t se

Suitable for classical or operatic music, this mode emphasizes the surround channels in order to widen the stereo image, and simulates the natural reverberation of a large hall.

Suitable for acoustic instruments, vocals, and jazz, this mode emphasizes the front stereo image, giving the impression of being right in front of the stage.

Suitable for rock or pop music, listening to music in this mode creates a lively sound field with a powerful acoustic image, like being at a club or rock concert.

This mode adds realistic acoustics to TV shows produced in a TV studio, surround effects to the entire sound, and clarity to voices.

In this mode, the sound has a dramatic feel with a similar atmosphere to Orchestra mode.

In this mode, sound localization is distinct with emphasis on bass.

In this mode, sound pressure is emphasized to heighten live feel.

In this mode, reverberation is increased and sound localization decreased slightly.

All Ch Stereo Ideal for background music, this mode fills the entire listening area with

Al l Ch Stereo

stereo sound from the front, surround, and surround back speakers.

Full Mono In this mode, all speakers output the same sound in mono, so the sound you

Fu l Monol

T-D (TheaterDimensional)

T – D

hear is the same regardless of where you are within the listening room.

With this mode you can enjoy a virtual surround sound even with only two or three speakers. This works by controlling how sounds reach the listener’s left and right ears. Good results may not be possible if there’s too much reverb, so we recommend that you use this mode in an environment with little or no natural reverb.

Source

A S D F G H

Speaker Layout

XCN

ZXC N

Page 29

■ Listening Modes

Listening Mode Description Input

Source

Direct In this mode, audio from the input source is output without surround-sound

Di rec t

processing. The speaker configuration (presence of speakers) and speaker distance settings are enabled, but much of the processing set via Home menu is disabled. A/V Sync does not have effect on the analog audio. See “Advanced Setup” for more details (➔ page 34).

A S D F G H

Stereo Sound is output from the front left and right speakers and subwoofer.

Stereo

Mono Use this mode when watching an old movie with a mono soundtrack, or use

Mono

it with the foreign language soundtracks recorded in the left and right channels of some movies. It can also be used with DVDs or other sources containing multiplexed audio, such as karaoke DVDs.

Multichannel This mode is for use with PCM multichannel sources.

Mu l t i ch

Dolby Pro Logic IIx Dolby Pro Logic II

PL Mov i e

PL Mus i c

PL Game

PL x Mo v i e

PL x Music

PL x Game

Dolby Pro Logic IIx expands any 2-channel source for 7.1-channel playback. It provides a very natural and seamless surround-sound experience that fully envelops the listener. As well as music and movies, video games can also benefit from the dramatic spatial effects and vivid imaging. If you’re not using any surround back speakers, Dolby Pro Logic II will be used instead of Dolby Pro Logic IIx.

• Dolby PLIIx Movie

Use this mode with any stereo or Dolby Surround (Pro Logic) movie (e.g., TV, DVD, VHS).

• Dolby PLIIx Music

Use this mode with any stereo or Dolby Surround (Pro Logic) music source (e.g., CD, radio, cassette, TV, VHS, DVD).

• Dolby PLIIx Game

Use this mode with video games, especially those that bear the Dolby Pro

A S D F G H

DXCN

SXCN

Logic II logo.

• Dolby PLIIx Movie, Dolby PLIIx Music

These modes use the Dolby Pro Logic IIx modes to expand 5.1-channel sources for 7.1-channel playback.

Dolby Pro Logic IIz Height

PL z He i gh t

Dolby EX These modes expand 5.1-channel sources for 6.1/7.1-channel playback.

Dolby EX

Dolby D EX

PL z He i gh t

Dolby Pro Logic IIz Height is designed to more effectively use existing program material when height channel speaker outputs are present. Dolby Pro Logic IIz Height can be used to upmix a variety of sources from movies and music, but are particularly well-suited to upmix game content.

They’re especially suited to Dolby EX soundtracks that include a matrixencoded surround back channel. The additional channel adds an extra dimension and provides an enveloping surround sound experience, perfect for rotating and fly-by sound effects.

S D F

D H

Speaker Layout

ZXC

ZXC N

Page 30

Listening Mode Description Input

Source

Dolby Digital In this mode, audio from the input source is output without surround-sound

Dolby D

Dolby Digital Plus

Dolby D +

processing. The speaker configuration (presence of speakers), crossover frequency, speaker distance, A/V Sync and much of the processing set via

Home menu are enabled. See “Advanced Setup” for more details (➔ page 34).

Dolby TrueHD

DTS

DTS-HD High

D F

D XCN F XCN

D XCN

F XCN

Resolution Audio

DTS– HD HR

DTS-HD Master Audio

DTS– HD MST R

DTS Express

DTS E xp r e s s

DSD

DTS 96/24

DTS 96 / 2 4

DTS-ES Discrete

ES Discrete

This mode is for use with DTS 96/24 sources. This is high-resolution DTS with a 96 kHz sampling rate and 24-bit resolution, providing superior fidelity. Use it with DVDs that bear the DTS 96/24 logo.

This mode is for use with DTS-ES Discrete soundtracks, which use a discrete surround back channel for true 6.1/7.1-channel playback. The seven totally separate audio channels provide better spatial imaging and 360-

D XCN F XCN

D XCN

degree sound localization, perfect for sounds that pan across the surround channels. Use it with DVDs that bear the DTS-ES logo, especially those with a DTS-ES Discrete soundtrack.

DTS-ES Matrix

ES Ma t r i x

Neo:6 This mode expands any 2-channel source for up to 7.1-channel playback. It

Neo 6:Neo 6:

Neo 6:Neo 6 C i nema:

Neo 6 Music:

This mode is for use with DTS-ES Matrix soundtracks, which use a matrixencoded back-channel for 6.1/7.1-channel playback. Use it with DVDs that bear the DTS-ES logo, especially those with a DTS-ES Matrix soundtrack.

S XCN

uses seven full-bandwidth channels of matrix decoding for matrix-encoded material, providing a very natural and seamless surround sound experience that fully envelops the listener.

•Neo:6 Cinema

Use this mode with any stereo movie (e.g., TV, DVD, VHS).

•Neo:6 Music

Use this mode with any stereo music source (e.g., CD, radio, cassette, TV, VHS, DVD).

This mode uses Neo:6 to expand 5.1-channel sources for 6.1/7.1-channel

playback.

Speaker Layout

XCN

Note

These listening modes cannot be selected during USB or iPod playback.

When the input source contains the encoded front high channel, front high speakers output the sound.

If there are no surround back speakers, Dolby Pro Logic II is used.

Surround back speakers are not supported.

Front high speakers are not supported.

For the Blu-ray Discs, Dolby Digital is used in a 3.1/5.1-channel speaker system.

AV receiver can input the DSD signal from HDMI IN. Setting the output setting on the player side to PCM might obtain a better sound according to the player. In that case, set the output setting on the player side to PCM.

If there are no surround back speakers, DTS is used.

• The listening modes cannot be selected with some source formats.

Page 31

Using the Home Menu

Using the Sleep Timer

The Home menu provides you quick access to frequently used menus without having to go through the long standard menu. This menu enables you to change settings and view the current information.

The Home menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver’s display when changing settings.

Press RECEIVER followed by HOME.

The Home menu will be superimposed on the TV screen.

Use q/w and ENTER to make the desired selection.

■ Input

` You can select the input source while viewing the

information as follows: the name of input selectors, input assignments.

Press ENTER to display the current input source, followed by q/w to select the desired

input source. Pressing ENTER again switches to the selected input source.

■ Audio

` You can change the following settings: “Bass”,

“Treble”, “Subwoofer Level”, “Center Level”, “Audyssey”, “Dynamic EQ”, “Dynamic Volume”, “Late Night”, “Music Optimizer”, and “Cinema Filter”.

See also:

• “Audyssey” (➔ page 39)

• “Using the Audio Settings” (➔ page 43)

■ Info

` You can view the information of the following

items: “Input” and “Output”.

■ Listening Mode

` You can select the listening modes that are

grouped in the following categories: “MOVIE/TV”, “MUSIC” and “GAME”.

Use q/w to select the category and e/r to select the listening mode. Press ENTER to switch to the selected listening mode.

With the sleep timer, you can set the AV receiver to turn off automatically after a specified period.

Press RECEIVER followed by SLEEP repeatedly

to select the required sleep time.

The sleep time can be set from 90 to 10 minutes in 10 minute steps.

The SLEEP indicator lights on the display when the sleep timer has been set. The specified sleep time appears on the display for about 5 seconds, then the previous display reappears.

Tip

• If you need to cancel the sleep timer, press SLEEP repeatedly until the SLEEP indicator goes off.

• To check the time remaining until the AV receiver sleeps, press SLEEP. Note that if you press again on SLEEP as the time being displayed is equal or inferior to 10 minutes, the sleep timer will go off.

Note

Depending on the input source and listening mode, not all channels shown here output the sound.

Page 32

Setting the Display Brightness

Changing the Input Display

You can adjust the brightness of the AV receiver’s display.

Press RECEIVER followed by DIMMER

repeatedly to select: dim, dimmer, or normal brightness.

Tip

• (North American and Brazilian models) Alternatively, you can use the AV receiver’s DIMMER.

Displaying Source Information

You can display various information about the current input source as follows.

Press RECEIVER followed by DISPLAY

repeatedly to cycle through the available information.

The following information can typically be displayed.

Input source &

volume

Listening mode

Signal format*2 or sampling frequency

When you connect an u-capable Onkyo component, you must configure the input display so that u can work

properly. This setting can be done only from the front panel.

Press TV/CD, GAME or VCR/DVR.

“TV/CD”, “GAME” or “VCR/DVR” appears on the display.

Press and hold down the same button (about

3 seconds) to change the input display.

Repeat this step to select the desired input display.

■ TV/CD:

TV/CD → DOCK

→

TAPE

■ GAME:

GAME ↔ DOCK

■ VCR/DVR:

VCR/DVR ↔ DOCK

Note

• DOCK cannot be selected for multiple input selectors at the same time.

• Enter the appropriate remote control code before using the remote controller for the first time (➔ page 47).

→

Tip

• Alternatively, you can use the AV receiver’s DISPLAY.

When AM or FM radio is used, the band, preset number, and frequency are displayed.

If the input signal is analog, “Analog” is displayed. If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not PCM, the signal format is displayed. Information is displayed for about three seconds, then the previously displayed information reappears.

Using the Music Optimizer

The Music Optimizer function enhances the sound quality of compressed music files.

Press MUSIC OPTIMIZER on the front panel.

The M.Opt indicator lights on the display.

Tip

• Alternatively, you can use the remote controller’s HOME and arrow buttons.

• See “Music Optimizer” for more details (➔ page 44).

Page 33

Muting the AV Receiver

You can temporarily mute the output of the AV receiver.

Press RECEIVER followed by MUTING.

The output is muted and the MUTING indicator flashes on the display.

Tip

• To unmute, press MUTING again or adjust the volume.

• The mute is cancelled when the AV receiver is set to Standby.

Using Headphones

Connect a pair of stereo headphones with a

standard plug (1/4 inch or 6.3 mm) to the

PHONES jack.

Note

• Always turn down the volume before connecting your headphones.

• While the headphones plug is inserted in the PHONES jack, the speakers are turned off.

• When you connect a pair of headphones, the listening mode is set to Stereo, unless it’s already set to Stereo, Mono, or Direct.

Recording Separate AV Sources

Here you can record audio and video from completely separate sources, allowing you to overdub audio onto your video recordings. This function takes advantage of the fact that when an audio-only input source (TV/CD) is selected, the video input source remains unchanged.

In the following example, audio from the CD player connected to the TV/CD IN and video from the camcorder connected to the AUX INPUT VIDEO are recorded by the VCR connected to the VCR/DVR OUT jacks.

Camcorder

Recording

This section explains how to record the selected input source to a component with recording capability, and how to record audio and video from different sources.

AV Recording

Audio sources can be recorded to a recorder (e.g., cassette tape deck, CDR, MD recorder). Video sources can be recorded to a video recorder (e.g., VCR, DVD recorder).

Use the input selector buttons to select the source

that you want to record.

You can watch the source while recording. The AV receiver’s MASTER VOLUME control has no effect on recording.

On your recorder, start recording.

On the source component, start playback.

If you select another input source during recording, that input source will be recorded.

VCRCD player

: Video signal : Audio signal

Prepare the camcorder and CD player for

playback.

Prepare the VCR for recording.

Press AUX input selector.

Press TV/CD input selector.

This selects the CD player as the audio source, but leaves the camcorder as the video source.

Start recording on the VCR and start playback on

the camcorder and CD player.

The video from the camcorder and the audio from the CD player are recorded by the VCR.

Page 34

Advanced Operations

Advanced Setup

On-screen Setup Menus

Note

• The on-screen setup menus are displayed when: – There is no video input, or – The video input is 480p, 576p, 720p, 1080i, or 1080p.

Setup Menu

1. HDMI Input

2. Component

3. Digital Audio

4. Sp Config

5. Sp Distance

6. Level Cal

7. Audio Adjust

g h

8. Source Setup

9. Hardware

10. HDMI Setup

a HDMI Input

(➔ page 35)

BD/DVD VCR/DVR CBL/SAT GAME AUX

TUNER

TV/CD

b Component

(➔ page 35)

BD/DVD VCR/DVR CBL/SAT GAME AUX

TUNER

TV/CD

c Digital Audio

(➔ page 35)

BD/DVD VCR/DVR CBL/SAT GAME AUX

TUNER

TV/CD

d Sp Config

(➔ page 36)

Subwoofer Front Center Surround Front High Surround Back Surround Back Ch Crossover Double Bass

BD/DVD VCR/DVR CBL/SAT GAME

AUX TUNER TV/CD

e Sp Distance

(➔ page 37)

Unit Left Front High Left Center Front High Right Right Surround Right SurrBack Right SurrBack Left Surround Left Subwoofer

f Level Cal

(➔ page 37)

Left Front High Left Center Front High Right Right Surround Right SurrBack Right SurrBack Left Surround Left Subwoofer

g Audio Adjust

(➔ page 37)

Input Ch (Mux) Input Ch (Mono) Panorama Dimension Center Width Height Gain Dolby EX Center Image Listening Angle

h Source Setup

(➔ page 39)

Audyssey Dynamic EQ Reference Level Dynamic Volume A/V Sync Name Audio Selector Fixed Mode

i Hardware

(➔ page 41)

Volume OSD Remote ID AM/FM Freq Step Auto Standby

j HDMI Setup

(➔ page 42)

HDMI Ctrl (RIHD) HDMI Through Audio TV Out Audio Return Ch LipSync

Common Procedures in Setup Menu

Remote indicator

RECEIVER

ENTER

q/w/e/r

SETUP

The on-screen setup menus appear on the connected TV and provide a convenient way to change the AV receiver’s various settings. Settings are organized into 10 categories on the main menu.

Carry out the settings by using the on-screen display.

Press RECEIVER followed by SETUP.

Tip

• If the main menu doesn’t appear, make sure the appropriate external input is selected on your TV.

Use q/w to select a menu, and then press ENTER.

Use q/w to select target, and use e/r to change the

setting.

Press SETUP to close the menu. Press RETURN to return to the main menu.

Note

• This procedure can also be performed on the AV receiver by using SETUP, arrow buttons, and ENTER.

• During Audyssey 2EQ

Room Correction and Speaker Setup, messages, etc., that are displayed on the TV screen will appear in the Display.

Explanatory Notes

b c

Menu Sp Config

■ Subwoofer

` Yes ` No

a Menu selection b Setting target c Setting options (default setting underlined)

RETURN

Page 35

HDMI Input

Menu HDMI Input

If you connect a video component to an HDMI input, you must assign that input to an input selector. For example, if you connect your Blu-ray Disc/DVD player to HDMI IN 2, you must assign “HDMI2” to the “BD/DVD” input selector. Here are the default assignments.

Input selector Default assignment

BD/DVD HDMI1

VCR/DVR HDMI2

CBL/SAT HDMI3

GAME HDMI4

AUX -----

TV/CD -----

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,

TV/CD

` HDMI1, HDMI2, HDMI3, HDMI4:

Select a corresponding HDMI input that the video component has been connected.

` -----:

Select if you’re not using the HDMI OUT.

Each HDMI input cannot be assigned to two input selectors or more. When HDMI1 - HDMI4 have already been assigned, you must set first any unused input selectors to “-----”, or you will be unable to assign HDMI1 - HDMI4 to input selector.

Note

•When an HDMI IN is assigned to an input selector as explained here, the digital audio input for that input selector is automatically set to the same HDMI IN.

• Do not assign the component connected with the HDMI input to TV/CD selector when you set “HDMI Ctrl (RIHD)” setting to “On” (➔ page 42). Otherwise, appropriate CEC (Consumer Electronics Control) operation will not be guaranteed.

Component (Component Video Input)

Menu Component

If you connect a video component to a component video input, you must assign that input to an input selector. For example, if you connect your Blu-ray Disc/DVD player to COMPONENT VIDEO IN 2, you must assign “IN2” to the “BD/DVD” input selector.

Here are the default assignments.

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,

TV/CD

` IN1, IN2:

Select a corresponding component video input that the video component has been connected.

` -----:

Select if you’re not using the COMPONENT VIDEO OUT.

Digital Audio (Digital Audio Input)

Menu Digital Audio

If you connect a component to a digital audio input, you must assign that input to an input selector. For example, if you connect your CD player to the OPTICAL IN 1, you must assign “OPTICAL1” to the “TV/CD” input selector.

Here are the default assignments.

Input selector Default assignment

BD/DVD COAXIAL1

VCR/DVR - - - - -

CBL/SAT COAXIAL2

GAME OPTICAL1

AUX -----

TV/CD OPTICAL2

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,

TV/CD

` COAXIAL1, COAXIAL2, OPTICAL1,

OPTICAL2:

Select a corresponding digital audio input that the component has been connected.

` -----:

Select if the component is connected to an analog audio input.

Note

• When an HDMI IN is assigned to an input selector in “HDMI Input” (➔ page 35), this input assignment is automatically set to the same HDMI IN. And in addition to the usual inputs (e.g., COAXIAL1, COAXIAL2, etc.), you can also select HDMI inputs.

• Available sampling rate for PCM signals from a digital input (optical and coaxial) is 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.

Input selector Default assignment

BD/DVD IN1

VCR/DVR - - - - -

CBL/SAT IN2

GAME -----

AUX -----

TV/CD -----

Page 36

Sp Config (Speaker Configuration)

Menu Sp Config

Some of the settings in this section are set automatically by Audyssey 2EQ® Room Correction and Speaker Setup (➔ page 24).

Here you can check the settings made by Audyssey 2EQ Room Correction and Speaker Setup, or set them manually, which is useful if you change one of the connected speakers after using Audyssey 2EQ Room Correction and Speaker Setup.

This section explains how to specify which speakers are connected and their sizes.

For speakers with a cone diameter larger than 6-1/2 inches (16 cm), specify Large (full band). For those with a smaller diameter, specify Small (default crossover 100 Hz). The crossover frequency can be changed in the “Crossover (Crossover Frequency)” (➔ page 36).

Note

• These settings are not available in either of the following cases: – a pair of headphones is connected. –the “Audio TV Out” setting is set to “On” (➔ page 42). –“HDMI Ctrl (RIHD)” is set to “On” (➔ page 42) and

you’re listening through your TV speakers.

■ Subwoofer

` Yes ` No

■ Front

` Small

` Large:

Select based on the cone diameter.

Note

•If the “Subwoofer” setting is set to “No”, this setting is fixed at “Large” and does not appear.

■ Center*1, Surround*1, Front High

Surround Back

*1*2*3*6

` Small: ` Large:

Select based on the cone diameter.

` None:

Select if no speaker is connected.

Note

If the “Front” setting is set to “Small”, the “Large” option cannot be selected.

If the “Surround” setting is set to “None”, this setting cannot be selected.

If the “Surround” setting is set to “Small”, the “Large” option cannot be selected.

For “Front High”, the default is “None”.

If the “Surround Back” setting is set to other than “None”, this setting is set to “None”.

If the “Front High” setting is set to other than “None”, this setting is set to “None”.

Cone diameter

*1*2*3*4*5

■ Surround Back Ch

` 1ch:

Select if only one surround back speaker is connected.

` 2ch

: Select if two (left and right) surround back speakers are connected.

Note

•If the “Surround Back” setting is set to “None”, this setting cannot be selected.

■ Crossover (Crossover Frequency)

This setting is advantageous for the speakers that you specified as “Small” in the “Sp Config (Speaker Configuration)” (➔ page 36). To get the best bass performance from your speaker system, you need to set the crossover frequency according to the size and frequency response of your speakers.

` 40Hz, 50Hz, 60Hz, 70Hz, 80Hz, 90Hz, 100Hz,

120Hz, 150Hz, 200Hz Use the diameter of the smallest speaker in your system when choosing the crossover frequency.

Speaker cone diameter Crossover frequency

Over 8 in. (20 cm) 6-1/2 to 8 in. (16 to 20 cm) 5-1/4 to 6-1/2 in. (13 to 16 cm) 100 Hz 3-1/2 to 5-1/4 in. (9 to 13 cm) 120 Hz Under 3-1/2 in. (9 cm)

Choose the setting suitable for the speaker.

Note

• For a more accurate setting, look up the frequency response in the manuals supplied with your speakers and set accordingly.

• Choose a higher crossover frequency if you want more sound from your subwoofer.

40/50/60 Hz 70/80/90 Hz

150/200 Hz

■ Double Bass

This setting is not set automatically by Audyssey 2EQ Room Correction and Speaker Setup (➔ page 24).

` On ` Off

Turn this setting on to boost bass output by feeding bass sounds from the front left, right, and center channels to the subwoofer.

Note

• This function can be set only if the “Subwoofer” setting is set to “Yes”, and the “Front” setting is set to “Large” (➔ page 36).

Page 37

Sp Distance (Speaker Distance)

Menu Sp Distance

This setting is set automatically by Audyssey 2EQ® Room Correction and Speaker Setup (➔ page 24).

For the center speaker and subwoofer, the level settings made by using HOME are saved here as the default settings.

Tip

• If you’re using a handheld sound level meter, adjust the level of each speaker so that it reads 75 dB SPL at the listening position, measured with C-weighting and slow reading.

Here you can specify the distance from each speaker to the listening position so that the sound from each speaker arrives at the listener’s ears as the sound designer intended.

■ Unit

` feet:

Distances can be set in feet. Range: 1ft to 30ft in 1 foot steps.

` meters:

Distances can be set in meters. Range: 0.3m to 9.0m in 0.3 meter steps.

(The default setting varies from country to country.)

■ Left, Front High Left, Center, Front High Right,

Right, Surround Right, Surr Back Right, Surr Back Left, Surround Left, Subwoofer

` Specify the distance from the each speaker to your

listening position.

Note

you’re listening through your TV speakers.

• Speakers that you set to “No” or “None” in the “Sp Config (Speaker Configuration)” (➔ page 36) cannot be selected.

Level Cal (Level Calibration)

Audio Adjust

Menu Audio Adjust

With the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like.

Multiplex/Mono Settings

■ Multiplex

Input Ch (Mux)

` Main ` Sub ` Main/Sub

This setting determines which channel of a stereo multiplex source is output. Use it to select audio channels or languages with multiplex sources, multilingual TV broadcasts, and so on.

■ Mono

Input Ch (Mono)

` Left + Right ` Left ` Right

This setting specifies the channel to be used for playing any 2-channel digital source such as Dolby Digital, or 2channel analog/PCM source in the Mono listening mode.

Menu Level Cal

This setting is set automatically by Audyssey 2EQ Room Correction and Speaker Setup (➔ page 24).

Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position.

■ Left, Front High Left, Center

, Front High Right, Right, Surround Right, Surr Back Right, Surr Back Left, Surround Left

` –12 dB to 0dB

■ Subwoofer

to +12 dB in 1 dB step.

` –15 dB to 0dB to +12 dB in 1 dB step.

Note

• These settings cannot be calibrated in either of the following cases: – a pair of headphones is connected. –the “Audio TV Out” setting is set to “On” (➔ page 42). –“HDMI Ctrl (RIHD)” is set to “On” (➔ page 42) and

you’re listening through your TV speakers.

– the AV receiver is muted.

• Speakers that you set to “No” or “None” in the “Sp Config (Speaker Configuration)” (➔ page 36) cannot be selected.

Page 38

Dolby Settings

■ PLIIx Music (2ch Input)

These settings apply to only 2-channel stereo sources. If you’re not using any surround back speakers, these settings apply to Dolby Pro Logic II, not Dolby Pro Logic

IIx.

Panorama

` On ` Off

Turn this setting on to broaden the width of the front stereo image when using the Dolby Pro Logic IIx Music listening mode.

Dimension

` –3 to 0

With this setting, you can move the sound field forward or backward when using the Dolby Pro Logic IIx Music listening mode. Higher settings move the sound field backward. Lower settings move it forward. If the stereo image feels too wide, or there’s too much surround sound, move the sound field forward to improve the balance. Conversely, if the stereo image feels like it’s in mono, or there’s not enough surround sound, move it backward.

Center Width

` 0 to 3

With this setting, you can adjust the width of the sound from the center speaker when using the Dolby Pro Logic IIx Music listening mode. Normally, if you’re using a center speaker, the center channel sound is output from only the center speaker. (If you’re not using a center speaker, the center channel sound will be distributed to the front left and right speakers to create a phantom center). This setting controls the front left, right, and center mix, allowing you to adjust the weight of the center channel sound.

PLIIz Height Gain

` Low

` Mid

` High

The Height Gain Control in Dolby Pro Logic IIz enables the listener to select how much gain is applied to the front high speakers. There are three settings, “Low”, “Mid” and “High”, and the front high speakers are accentuated in that order. While “Mid” is the default listening setting, the listener may adjust the Height Gain Control to their personal preference.

Note

•If the “Front High” settings is set to “None” (➔ page 36), this

setting cannot be selected.

to +3

to 7

■ Dolby EX

This setting determines how Dolby EX encoded signals are handled. This setting is unavailable if no surround back speakers are connected. This setting is effective with Dolby Digital, Dolby Digital Plus and Dolby TrueHD only.

Dolby EX

` Auto:

If the source signal contains a Dolby EX flag, the Dolby EX listening mode is used.

` Manual

You can select any available listening mode.

Note

•If the “Surround Back” Setting is set to “None” (➔ page 36), this setting cannot be selected.

•If the “Front High” setting is set to other than “None”, this setting is fixed at “Manual” (➔ page 36).

DTS Setting

■ Neo:6 Music

Center Image

` 0 to 2

to 5 The DTS Neo:6 Music listening mode creates 6-channel surround sound from 2-channel stereo sources. With this

setting, you can specify by how much the front left and right channel output is attenuated in order to create the center channel.

Setting a value “0” in the middle is set to hear a sound. Sound is spread in left and right (the outside) so that the set value is made big. Please adjust by liking.

Theater-Dimensional Setting

■ Theater-Dimensional

Listening Angle

` Wide

Select if the listening angle is 40 degrees.

` Narrow:

Select if the listening angle is 20 degrees.

With this setting, you can optimize the TheaterDimensional listening mode by specifying the angle of the front left and right speakers relative to the listening position. Ideally, the front left and right speakers should be equidistant from the listening position and at an angle close to one of the two available settings.

Front left

speaker

Front right

speaker

20°/40°

Page 39

Source Setup

Menu Source Setup

Preparation

Press the input selector buttons to select an input source.

Audyssey

The tone for each speaker is set automatically by Audyssey 2EQ To enable the following settings, you must first perform the Room Correction and Speaker Setup (➔ page 24).

■ Audyssey

` Off ` Movie:

Select this setting for movie material. The Audyssey indicator will light (➔ page 8).

` Music:

Select this setting for music material. The Audyssey indicator will light (➔ page 8).

Note

•When “Audyssey Quick Start” has been used for measurement, the “Audyssey” cannot be selected.

• Audyssey equalizing does not work for DSD sources.

• These technologies cannot be used when: – a pair of headphones is connected, or – Direct listening mode is selected, or –the USB input selector is selected.

■ Dynamic EQ

` Off ` On:

Audyssey Dynamic EQ The Dynamic EQ indicator will light (➔ page 8).

With Audyssey Dynamic EQ, you can enjoy great sound even when listening at low volume levels.

Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. It does so by selecting the correct frequency response and surround volume levels moment-by-moment so that the content sounds the way it was created at any volume level — not just at reference level.

Note

• These technologies cannot be used when: – a pair of headphones is connected, or – Direct listening mode is selected, or –the USB input selector is selected.

Room Correction and Speaker Setup.

becomes active.

■ Reference Level

Audyssey Dynamic EQ Reference Level Offset

` 0dB

It should be used when listening to movies.

` 5dB:

Select this setting for content that has a very wide dynamic range, such as classical music.

` 10 dB:

Select this setting for jazz or other music that has a wider dynamic range. This setting should also be selected for TV content as that is usually mixed at 10 dB below film reference.

` 15 dB:

Select this setting for pop/rock music or other program material that is mixed at very high listening

levels and has a compressed dynamic range. Movies are mixed in rooms calibrated for film reference. To achieve the same reference level in a home theater

system each speaker level must be adjusted so that –30 dBFS band-limited (500 Hz to 2000 Hz) pink noise produces 75 dB sound pressure level at the listening position. A home theater system automatically calibrated by Audyssey 2EQ will play at reference level when the master volume control is set to the 0 dB position. At that level you can hear the mix as the mixers heard it.

Audyssey Dynamic EQ is referenced to the standard film mix level. It makes adjustments to maintain the reference response and surround envelopment when the volume is turned down from 0 dB. However, film reference level is not always used in music or other non-film content. The Dynamic EQ Reference Level Offset provides three offsets from the film level reference (5 dB, 10 dB, and 15 dB) that can be selected when the mix level of the content is not within the standard.

Note

• If “Dynamic EQ” setting is set to “Off”, these technologies

cannot be used.

■ Dynamic Volume

` Off ` Light:

Light Compression Mode becomes active.

` Medium:

Medium Compression Mode becomes active.

` Heavy:

Heavy Compression Mode becomes active. This

setting affects volume the most. It quiets the loud

parts, such as explosions, and boosts the quiet parts

so they can be heard.

Note

• If you make Dynamic Volume active, “Dynamic EQ” is set to

“On”. The Dynamic Vol indicator will light (➔ page 8).

• When “Dynamic EQ” is set to “Off”, “Dynamic Volume”

becomes “Off” automatically.

• These technologies cannot be used when:

– a pair of headphones is connected, or – Direct listening mode is selected, or –the USB input selector is selected.

Page 40

About Audyssey Dynamic EQ

Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Dynamic EQ selects the correct frequency response and surround levels moment-by-moment at any user-selected volume setting. The result is bass response, tonal balance, and surround impression that remain constant despite changes in volume. Dynamic EQ combines information from incoming source levels with actual output sound levels in the room, a prerequisite for delivering a loudness correction solution. Audyssey Dynamic EQ works well by itself.

However, if Audyssey 2EQ

is on, the two technologies work in tandem to provide well-balanced sound for every listener at any volume level.

Preset Name For Input Selector

■ Name

` ---, Blu-ray, DVD, HD DVD, VCR, DVR, Tivo,

CableSTB, SAT STB, PS3, Wii, Xbox, PC, TV, CD, TAPE, iPod:

To reset to the default, select “---”.

You can enter a preset name for each individual input selector for easy identification. When entered, the preset name will appear on the display.

Note

• Can not set the input selector by the same name.

• This menu cannot be used for the AM, FM or USB input selector.

Audio Selector

About Audyssey Dynamic Volume

Audyssey Dynamic Volume solves the problem of large variations in volume level between television programs, commercials, and between the soft and loud passages of movies. Dynamic Volume looks at the preferred volume setting by the user and then monitors how the volume of program material is being perceived by listeners in real time to decide whether an adjustment is needed. Whenever necessary, Dynamic Volume makes the necessary rapid or gradual adjustments to maintain the desired playback volume level while optimizing the dynamic range. Audyssey Dynamic Volume works fine by itself, but can also be used with Audyssey Dynamic EQ. When both are on, Audyssey Dynamic EQ adjusts the perceived bass response, tonal balance, surround impression, and dialog clarity whether watching movies, flipping between television channels, or changing from stereo to surround sound content, when Dynamic Volume adjusts the volume.

A/V Sync

■ A/V Sync

` 0ms to 400 ms in 10 ms steps

When using progressive scanning on your Blu-ray Disc/DVD player, you may find that the picture and sound are out of sync. With this setting, you can correct this by delaying the audio signals.

To view the TV picture while setting the delay, press ENTER.

To return to the previous screen, press RETURN.

The range of values you can adjust will depend on whether your TV or display supports HDMI Lip Sync and if the “LipSync” setting is set to “On” or not (➔ page 43).

Note

• A/V Sync is disabled when the Direct listening mode is used with an analog input source.

■ Audio Selector

` ARC:

The audio signal from your TV tuner can be sent to the HDMI OUT of the AV receiver.

With this selection the TV’s audio can be automatically selected as a priority among other assignments.

` HDMI:

This can be selected when HDMI IN has been assigned as an input source. If both HDMI (HDMI

IN) and digital audio inputs (COAXIAL IN or OPTICAL IN) have been assigned, HDMI input is

automatically selected as a priority.

` COAXIAL:

This can be selected when COAXIAL IN has been assigned as an input source. If both coaxial and HDMI inputs have been assigned, coaxial input is automatically selected as a priority.

` OPTICAL:

This can be selected when OPTICAL IN has been assigned as an input source. If both optical and HDMI inputs have been assigned, optical input is automatically selected as a priority.

` Analog:

The AV receiver always outputs analog signals.

You can set priorities of audio output when there are both digital and analog inputs.

Note

• The setting is stored individually for each input selector.

• This setting can be made only for the input source that is assigned as HDMI IN, COAXIAL IN, or OPTICAL IN. If both HDMI (HDMI IN) and digital audio inputs (COAXIAL IN or OPTICAL IN) are assigned, HDMI input will be selected as a priority by setting to “ARC” (➔ page 42). To select the digital audio input, see “Digital Audio (Digital Audio Input)” (➔ page 35).

You can select “ARC” if you select the TV/CD input selector. But you cannot select it if you’ve selected “Off” in the “Audio Return Ch” setting (➔ page 42).

Page 41

Setting the Incoming Digital Signal (Fixed Mode)

■ Fixed Mode

` Off

: The format is detected automatically. If no digital input signal is present, the corresponding analog input is used instead.

` PCM:

Only 2-channel PCM format input signals will be heard. If the input signal is not PCM, the PCM indicator will flash and noise may also be produced.

` DTS:

Only DTS (but not DTS-HD) format input signals will be heard. If the input signal is not DTS, the DTS indicator will flash and there will be no sound.

When “HDMI”, “COAXIAL” or “OPTICAL” is selected in the “Audio Selector” setting, you can then specify the signal type in “Fixed Mode”. Normally, the AV receiver detects the signal format automatically. However, if you experience either of the following issues when playing PCM or DTS material, you can manually set the signal format to PCM or DTS.

• If the beginnings of tracks from a PCM source are cut off, try setting the format to PCM.

• If noise is produced when fast forwarding or reversing a DTS CD, try setting the format to DTS.

Note

• The setting will be reset to “Off” when you change the setting in the “Audio Selector” (➔ page 40).

Hardware

Menu Hardware

OSD Setting

■ Volume OSD

` On ` Off

You can select if you wish to display the volume level onscreen, when it is adjusted.

Changing the remote controller’s ID

While holding down RECEIVER, press and hold

down SETUP until the remote indicator lights (about 3 seconds) (➔ page 34).

Use the number buttons to enter ID 1, 2, or 3.

The remote indicator flashes twice.

Tuner

■ AM/FM Freq Step (North American and Brazilian

models)

` 10kHz/200kHz ` 9kHz/50kHz:

Select the frequency step according to your area.

■ AM Freq Step (Asian models)

` 10kHz: ` 9kHz

Select the frequency step according to your area. For AM/FM tuning to work properly, you must specify the AM/FM frequency step used in your area. Note that when

this setting is changed, all radio presets will be deleted.

Auto Standby

■ Auto Standby

` Off ` On

When “Auto Standby” is set to “On”, AV receiver will automatically perform standby operation if there is no operation for 30 minutes with no audio and no video signal input. “Auto Standby” will display on the display and OSD from 30 seconds before the Auto Standby functions. Default setting: On (Asian models), Off (North

American and Brazilian models)

Note

• Depending on some sources, the Auto Standby function may

activate during playback.

Remote Control Settings

■ Remote ID

` 1

, 2, or 3

When several Onkyo components are used in the same room, their remote ID codes may overlap. To differentiate the AV receiver from the other components, you can change its remote ID from “1”, to “2” or “3”.

Note

• If you do change the AV receiver’s remote ID, be sure to change the remote controller to the same ID (see below), otherwise, you won’t be able to control it with the remote controller.

Page 42

HDMI Setup

Menu HDMI Setup

■ HDMI Ctrl (RIHD)

` Off ` On

Turn this setting on to allow p-compatible components connected via HDMI to be controlled by the AV receiver (➔ page 57).

Note

• When set to “On” and close the menu, the name of connected p-compatible components and “RIHD On” are

displayed on the AV receiver. “Search…” → “(name)” → “RIHD On” When the AV receiver cannot receive the name of the component, it is displayed as “Player*” or “Recorder*”, etc (“*” means the number of two or more component).

• When an p-compatible component is connected to the AV receiver via the HDMI cable, the name of the connected component is displayed on the AV receiver display. For example, while you are watching TV broadcasting, if you operate a Blu-ray Disc/DVD player (being powered on) by the remote control of the AV receiver, the name of the Blu-ray Disc/DVD player is displayed on the AV receiver.

•Set to

“Off” when a connected piece of equipment is not

compatible or it is unclear whether the equipment is compatible or not.

• If movement is unnatural when set to

“Off”.

• Refer to the connected component’s instruction manual for details.

• When “HDMI Ctrl (RIHD)” setting is set to “On”, the power consumption on standby mode slightly increases. (Depending on the TV status, the AV receiver will enter standby mode as usual.)

■ HDMI Through

` Off ` Auto:

Detects the signal and automatically selects the input source.

` BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,

TV/CD:

Selects the input source for which the HDMI Through function is enabled.

` Last:

The HDMI Through function is activated on the input source selected at the time of setting the AV receiver to Standby mode.

When enabling the HDMI Through function, regardless of whether the AV receiver is On or in Standby, both audio and video stream from an HDMI input will be output to the TV or other components via HDMI connection. The HDMI THRU and HDMI indicators light when enabled.

This setting is set to “Auto” automatically when the above “HDMI Ctrl (RIHD)” is set to “On”.

“On”, change the setting

Note

• Only the input source assigned to the HDMI IN via “HDMI Input” is enabled (➔ page 35).

• The power consumption during standby mode will increase during the HDMI through function; however in the following cases, the power consumption can be saved: – The TV is in standby mode. – You are watching a TV program.

• Refer to the connected component’s instruction manual for details.

• Depending on the connected component, the correct input source may not be selected with the setting set to “Auto”.

• This setting is set to “Off” automatically when the “HDMI Ctrl (RIHD)” setting is set to “Off”.

■ Audio TV Out

` Off ` On

This preference determines whether the incoming audio signal is output from the HDMI output. You may want to turn this preference on if your TV is connected to the HDMI output and you want to listen to the audio from a connected component through your TV’s speakers. Normally, this should be set to “Off”.

Note

• Listening mode cannot be changed when this setting is set to “On” and the input source is not HDMI.

“On” is selected and the signal can be output from the TV, the

•If AV receiver will output no sound through its speakers. In this case, “TV Speaker” appears on the display by pressing DISPLAY.

“HDMI Ctrl (RIHD)” is set to “On”, this setting is fixed

•When

“Auto”.

• With some TVs and input signals, no sound may be output even when this setting is set to

•When the “Audio TV Out” setting is set to Ctrl (RIHD)” is set to TV’s speakers (➔ page 14), if you turn up the AV receiver’s volume control, the sound will be output from the AV receiver’s front left and right speakers. To stop the AV receiver’s speakers producing sound, change the settings, change your TV’s settings, or turn down the AV receiver’s volume.

“On”.

“On”, or “HDMI

“On” and you’re listening through your

■ Audio Return Ch (ARC)

` Off ` Auto

: The audio signal from your TV tuner can be sent to the HDMI OUT of the AV receiver.

The audio return channel (ARC) function allows an ARC capable TV to send the audio stream to the HDMI OUT of the AV receiver. To use this function, you must select the TV/CD input selector and your TV must support ARC function.

Note

• If you set “Audio Return Ch” to “Auto”, the “Audio Selector” settings of the TV/CD input selector will be automatically switched to “ARC” (➔ page 40).

•The “Audio Return Ch” setting can be set only when the above “HDMI Ctrl (RIHD)” setting is set to “On”.

• This setting is set to “Auto” automatically when the above “HDMI Ctrl (RIHD)” is set to “On” first time.

Page 43

■ LipSync

` Off ` On

This function allows the AV receiver to automatically correct any delay between the video and the audio, based on the data from the connected monitor.

Note

• This function works only if your HDMI-compatible TV supports HDMI Lip Sync.

After changing the settings of the “HDMI Ctrl (RIHD)”, “HDMI Through” or “Audio Return Ch”, turn off the power to all connected pieces of equipment and then turn them on again. Refer to the instructions for all connected pieces of equipment.

Using the Audio Settings

You can change various audio settings from the Home menu (➔ page 31).

Speaker Levels

■ Subwoofer Level

` –15 dB to 0dB to +12 dB in 1 dB steps

■ Center Level

` –12 dB to 0dB

You can adjust the volume of each speaker while listening to an input source.

These temporary adjustments are cancelled when the AV receiver is set to Standby. To save the setting you made here, go to “Level Cal (Level Calibration)” (➔ page 37) before setting the AV receiver to Standby.

Note

• You cannot use this function while the AV receiver is muted.

• Speakers that are set to “No” or “None” in the “Sp Config (Speaker Configuration)” (➔ page 36) cannot be adjusted.

This procedure can also be performed on the AV receiver by using its SUBWOOFER LEVEL.

to +12 dB in 1 dB steps

Audyssey

Press RECEIVER followed by HOME.

Use q/w and ENTER to select “Audio”, and then

use q/w/e/r to make the desired selection.

Note

• These settings are not available in either of the following cases: – a pair of headphones is connected. –the “Audio TV Out” setting is set to “On” (➔ page 42) and

an input selector other than HDMI is selected.

–“HDMI Ctrl (RIHD)” is set to “On” (➔ page 42) and

you’re listening through your TV speakers.

Tone Control Settings

■ Bass

` –10 dB to 0dB

You can boost or cut low-frequency sounds output from the front speakers.

■ Treble

` –10 dB to 0dB

You can boost or cut high-frequency sounds output from the front speakers.

You can adjust the bass and treble for the front speakers, except when the Direct listening mode is selected.

to +10 dB in 2 dB steps

■ Audyssey

See “Audyssey” of “Source Setup” (➔ page 39).

■ Dynamic EQ

See “Dynamic EQ” of “Source Setup” (➔ page 39).

■ Dynamic Volume

See “Dynamic Volume” of “Source Setup” (➔ page 39).

Note

• These technologies can be used when all the following conditions are met: – Room Correction and Speaker Setup is completed. Note that

“Audyssey” requires the “Audyssey 2EQ Full Calibration”

method. – Any listening mode other than Direct is selected. – A pair of headphones is not connected. – The input selector other than USB is selected.

• The setting is stored individually for each input selector.

Operating on the AV receiver

Press TONE on the AV receiver repeatedly to

select either “Bass” or “Treble”.

Use + and – on the AV receiver to adjust.

Note

• To bypass the bass and treble tone circuits, select the Direct listening mode.

Page 44

Late Night Function

CinemaFILTER

■ Late Night

For Dolby Digital and Dolby Digital Plus sources, the options are:

` Off ` Low:

Small reduction in dynamic range.

` High:

Large reduction in dynamic range.

For Dolby TrueHD sources, the options are:

` Auto

: The Late Night function is set to “On” or “Off” automatically.

` Off ` On

Turn this setting on to reduce the dynamic range of Dolby Digital material so that you can still hear quiet parts even when listening at low volume levels—ideal for watching movies late at night when you don’t want to disturb anyone.

Note

• The effect of the Late Night function depends on the material that you are playing and the intention of the original sound designer, and with some material there will be little or no effect when you select the different options.

• The Late Night function can be used only when the input source is Dolby Digital, Dolby Digital Plus, or Dolby TrueHD.

• The Late Night function is set to “Off” when the AV receiver is set to Standby. For Dolby TrueHD sources, it will be set to “Auto”.

■ Cinema Filter

` Off ` On

Turn this setting on to soften overly bright movie soundtracks, which are typically mixed for reproduction in a movie theater. CinemaFILTER can be used with the following listening modes: Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Pro Logic IIx Movie, Dolby Pro Logic II Movie, Dolby Pro Logic IIz Height, Multichannel, DTS, DTS-ES, DTS Neo:6 Cinema, DTS 96/24, Neo:6, DTS-HD High Resolution Audio, DTS-HD Master Audio and DTS Express.

Note

• The CinemaFILTER may not work when used with certain input sources.

Music Optimizer

■ Music Optimizer

` Off ` On

Turn this setting on to enhance the sound quality of compressed music files. Use it with music files that use “lossy” compression, such as MP3.

Tip

• Alternatively, you can use the AV receiver’s MUSIC OPTIMIZER.

Note

• The Music Optimizer function only works with PCM digital audio input signals with a sampling rate below 48 kHz and analog audio input signals. The Music Optimizer is disabled when the Direct listening mode is selected.

• The setting is stored individually for each input selector.

•The M.Opt indicator will light (➔ page 8).

Page 45

Controlling Other Components

iPod/iPhone Playback via Onkyo Dock

Using the Onkyo Dock

Dock is sold separately. Models sold are different depending on the region.

For the latest information on the Onkyo Dock components, see the Onkyo web site at: http://www.onkyo.com Before using the Onkyo Dock components, update your iPod/iPhone with the latest software, available from the Apple web site. For supported iPod/iPhone models, see the instruction manual of the Onkyo Dock.

RI Dock

With the RI Dock, you can easily play the music stored on your Apple iPod/iPhone through the AV receiver and enjoy great sound, and watch iPod/iPhone slideshows and videos on your TV. In addition, the onscreen display (OSD) allows you to view, navigate, and select your iPod/iPhone model’s contents on your TV, and with the supplied remote controller, you can control your iPod/iPhone from the comfort of your sofa. You can even use the AV receiver’s remote controller to operate your iPod/iPhone.

Note

• Enter the appropriate remote control code before using the AV receiver’s remote controller for the first time (➔ page 47).

• Connect the RI Dock to the AV receiver with an u cable (➔ page 16).

• Set the RI Dock’s RI MODE switch to “HDD” or “HDD/DOCK”.

• Set the AV receiver’s Input Display to “DOCK” (➔ page 32).

■ System Function

System On

When you turn on the AV receiver, RI Dock and iPod/iPhone turn on automatically. In addition, when RI Dock and iPod/iPhone are on, the AV receiver can be

turned on by pressing 8.

Auto Power On

If you press the remote controller’s 1 (Playback) while the AV receiver is on Standby, the AV receiver will automatically turn on, select your iPod/iPhone as the input source, and your iPod/iPhone will start playback.

Direct Change

If you start iPod/iPhone playback while listening to another input source, the AV receiver will automatically switch to the input to which RI Dock is connected.

Other Remote Controllers

You can use the remote controller that came with the AV receiver to control other iPod/iPhone functions. The available functionality depends on the AV receiver.

iPod/iPhone Alarm

If you use the Alarm function on your iPod/iPhone to start playback, the AV receiver will turn on at the specified time and select your iPod/iPhone as the input source automatically.

Note

• Linked operations do not work with video playback or when the alarm is set to play a sound.

• If you use your iPod/iPhone with any other accessories, iPod/iPhone playback detection may not work.

■ Operating Notes

• Use the AV receiver’s volume control to adjust the playback volume.

• While your iPod/iPhone is inserted in RI Dock, its volume control has no effect.

• If you do adjust the volume control on your iPod/iPhone while it’s inserted in RI Dock, be careful that it’s not set too loud before you reconnect your earphones.

Note

• On the iPod with video and iPod nano (1st generation), the click wheel is disabled during playback.

Controlling Your iPod/iPhone

By pressing REMOTE MODE that’s been programmed with the remote control code for your Dock, you can control your iPod/iPhone in the Dock with the following buttons. See “Remote Control Codes for Onkyo Components

Connected via u” for details on entering a remote control code (➔ page 47).

See to the Dock’s instruction manual for more information.

■ RI Dock

• Set the RI Dock’s RI MODE switch to “HDD” or “HDD/DOCK”.

• 8 may not work with a remote control code (without u). In this case, make an u connection and enter a remote control code 81993 (with u).

With the RI Control

In this case, make an u connection and enter a remote control code 81993 (with u).

• Set the AV receiver’s Input Display to “DOCK” (➔ page 32).

Without the RI Control

You must enter a remote control code 82990 first (➔ page 47).

Page 46

Press the appropriate REMOTE MODE first.

✔: Available buttons

Onkyo Dock

b c

g h

Buttons

a 8

TOP MENU

b c q/w/e/r, ENTER

PLAYLIST e/r

d 1, 3, 2, 5, 4, 7, 6

REPEAT ✔

RANDOM ✔

DISPLAY

MUTING ✔

ALBUM +/– ✔

h i VOL q/w

MENU ✔

MODE

✔

Note

• With some iPod/iPhone models and generations, certain buttons may not work as expected.

• For detailed operation of the iPod/iPhone, please refer to the instruction manual.

This button does not turn the Onkyo DS-A2 or DS-A2X RI Dock on or off. Your iPod/iPhone may not respond the first time you press this button, in which case you should press it again. This is because the remote controller transmits the On and Standby commands alternately, so if your iPod/iPhone is already on, it will remain on when the remote controller transmits an On command. Similarly, if your iPod/iPhone is already off, it will remain off when the remote controller transmits an Off command.

TOP MENU works as a Mode button when used with a DS-A2 RI Dock.

DISPLAY turns on backlight for 30 seconds.

Resume mode

With the Resume function, you can resume playback of the song that was playing when you removed your iPod/iPhone from the RI Dock or changed the OSD mode to Off.

u Dock

Page 47

Controlling Other Onkyo Components

You can use the AV receiver’s remote controller to control your other Onkyo AV components. This section explains how to enter the remote control code (with the default underlined) for a component that you want to control: DVD, CD, etc.

Preprogrammed Remote Control Codes

The following REMOTE MODE are preprogrammed with remote control codes for controlling the components listed. You do not need to enter a remote control code to control these components.

For details on controlling these components, see the pages indicated.

BD/DVD Onkyo Blu-ray Disc player (➔ page 48) TV/CD Onkyo CD player (➔ page 48)

Entering Remote Control Codes

You’ll need to enter a code for each component that you want to control.

Look up the appropriate remote control code in the

Remote Control Codes for Onkyo Components Connected via u.

While holding down REMOTE MODE to which

you want to enter a code, press and hold down

DISPLAY (about 3 seconds).

Note

• Remote control codes cannot be entered for RECEIVER.

• Apart from RECEIVER, remote control codes from any category can be entered for REMOTE MODE. However, these buttons also work as input selector buttons (➔ page 19), so choose a REMOTE MODE that corresponds with the input to which you connect your component. For example, if you connect your CD player to the CD input, choose TV/CD when entering its remote control code.

Within 30 seconds, use the number buttons to enter

the 5-digit remote control code.

The remote indicator flashes twice. If the remote control code is not entered successfully,

the remote indicator will flash once slowly.

Remote Control Codes for Onkyo Components Connected via u

Onkyo components that are connected via u are controlled by pointing the remote controller at the AV receiver, not the component. This allows you to control components that are out of view, in a rack, for example.

Make sure the Onkyo component is connected with

an u cable and an analog audio cable (RCA).

See “Connecting Onkyo u Components” for details (➔ page 16).

Enter the appropriate remote control code for

REMOTE MODE referring to the previous section.

` 42157:

Onkyo cassette tape deck with u

` 81993:

Onkyo Dock with u

Press REMOTE MODE, point the remote

controller at the AV receiver, and operate the component.

Controlling Onkyo components without u

If you want to control an Onkyo component by pointing the remote controller directly at it, or you want to control

an Onkyo component that’s not connected via u, use the following remote control codes:

` 30627:

Onkyo DVD player without u

` 71817:

Onkyo CD player without u

` 32900/33000:

Onkyo Blu-ray Disc player

` 32901/33004

Onkyo HD DVD player

` 70868:

Onkyo MD recorder without u

` 71323:

Onkyo CD recorder without u

` 82990:

Onkyo Dock without u

Page 48

Resetting REMOTE MODE Buttons

You can reset a REMOTE MODE to its default remote control code.

While holding down REMOTE MODE that you

want to reset, press and hold down HOME until the remote indicator lights (about 3 seconds).

Within 30 seconds, press REMOTE MODE again.

The remote indicator flashes twice, indicating that the button has been reset.

Each of REMOTE MODE is preprogrammed with a remote control code. When a button is reset, its preprogrammed code is restored.

Resetting the Remote Controller

You can reset the remote controller to its default settings.

While holding down RECEIVER, press and hold

down HOME until the remote indicator lights (about 3 seconds).

Within 30 seconds, press RECEIVER again.

The remote indicator flashes twice, indicating that the remote controller has been reset.

Controlling Other Components

By pressing REMOTE MODE that’s been programmed with the remote control code for your component, you can control Onkyo component as below. For details on entering a remote control code for a different component (➔ page 47).

Controlling a Blu-ray Disc/DVD Player, HD DVD Player

BD/DVD is preprogrammed with the remote control code

for controlling a component that supports the p The component must be able to receive remote control

commands via p and be connected to the AV receiver via HDMI.

Use the following remote control codes:

` 32910/33001/31612:

Blu-ray Disc/DVD player with p

The p supported by the AV receiver is the CEC system control function of the HDMI standard.

Page 49

Press the appropriate REMOTE MODE first.

✔: Available buttons

Components

i j

l m

Buttons

a 8

TOP MENU ✔

b c q/w/e/r, ENTER

SETUP ✔✔

d e 1, 3, 2, 5, 4,

7, 6

REPEAT ✔

RANDOM

MODE Number: 1 to 9, 0 ✔✔

Number: +10

DISPLAY ✔✔

MUTING ✔✔✔

DISC +/– ✔✔

MENU ✔

RETURN ✔

AUDIO

CLR ✔✔

DVD player

Blu-ray Disc player

HD DVD player

CD player/CD recorder

MD recorder

Cassette tape deck

✔✔✔

✔✔

✔

Note

• With some components, certain buttons may not work as expected, and some may not work at all.

The p function is not supported. The p supported by the AV receiver is the CEC system control function of the HDMI standard.

These buttons function as colored buttons or A, B, C, D buttons.

3 (Pause) functions as reverse playback.

Note

• See the “Controlling Your iPod/iPhone” about the operation of iPod/iPhone (➔ page 45).

Page 50

Appendix

Troubleshooting

If you have any trouble using the AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact your Onkyo dealer.

If you can’t resolve the issue yourself, try resetting the AV receiver before contacting your Onkyo dealer.

To reset the AV receiver to its factory defaults, turn it on and, while holding down VCR/DVR, press

8 ON/STANDBY. “Clear” will appear on the display and the AV receiver will enter Standby mode.

Note that resetting the AV receiver will delete your radio presets and custom settings.

Remote indicator

RECEIVER

HOME

To reset the remote controller to its factory defaults, while holding down RECEIVER, press and hold down HOME until the remote indicator lights (about 3 seconds). Within 30 seconds, press RECEIVER again.

Power

■ Can’t turn on the AV receiver

Make sure that the power cord is properly plugged into the wall outlet.

Unplug the power cord from the wall outlet, wait five seconds or more, then plug it in again.

■ The AV receiver turns off unexpectedly

When the set Auto Standby starts running, the AV receiver will automatically go standby.

—

■ When the power is restored after a power

interruption, “CHECK SP WIRE” appears on the display

The protection circuitry has been activated. Remove the power cord from the wall outlet immediately. Disconnect all speaker cables and input sources, and then leave the AV receiver with its power cord disconnected for 1 hour. After that, reconnect the power cord and set the volume to maximum. If the AV receiver stays on, set then the volume to minimum, disconnect the power cord, and reconnect your speakers and input sources. If the AV receiver turns off when you set the volume to maximum, disconnect the power cord, and contact your Onkyo dealer.

—

Audio

■ There’s no sound, or it’s very quiet

Make sure that the digital input source is selected properly.

Make sure that all audio connecting plugs are pushed in all the way.

Make sure that the inputs and outputs of all components are connected properly.

Make sure that the polarity of the speaker cables is correct, and that the bare wires are in contact with the metal part of each speaker terminal.

Make sure that the input source is properly selected. 19 Make sure that the speaker cables are not shorting. 12 Check the volume. The AV receiver is designed for

home theater enjoyment. It has a wide volume range, allowing precise adjustment.

If the MUTING indicator is flashing on the display, press the remote controller’s MUTING to unmute the AV receiver.

While a pair of headphones is connected to the PHONES jack, no sound is output from the speakers.

If there’s no sound from a DVD player connected to an HDMI IN, check the DVD player’s output settings, and be sure to select a supported audio format.

Check the digital audio output setting on the connected device. On some game consoles, such as those that support DVD, the default setting is off.

With some DVD-Video discs, you need to select an audio output format from a menu.

If your turntable uses an MC cartridge, you must connect an MC head amp, or an MC transformer.

Make sure that none of the connecting cables are bent, twisted, or damaged.

Not all listening modes use all speakers. 27 Specify the speaker distances and adjust the

individual speaker levels. Make sure that the speaker setup microphone is not

still connected. The input signal format is set to “PCM” or “DTS”.

Set it to “Off”.

14-16

—

Page 51

■ Only the front speakers produce sound

When the Stereo or Mono listening mode is selected, only the front speakers and subwoofer produce sound.

Check the Speaker Configuration. 36

■ Only the center speaker produces sound

If you use the Dolby Pro Logic IIx Movie, Dolby Pro Logic IIx Music, or Dolby Pro Logic IIx Game listening mode with a mono source, such as an AM radio station or mono TV program, the sound is concentrated in the center speaker.