One for All URC-4330 User Manual

CBL/SAT VCR DVD TV

SET

SLEEP

FFPLAYREW

PAUSESTOP

TV/VID

CH +

CH -

MUTE

VOL

REC

EXIT

SHIFT

POWER

4 DEVICES

UNIVERSAL REMOTE CONTROL

USER’S GUIDE

INTRODUCTION

The One For All 4 Devices Universal Remote Control is designed to operate three (or four) home entertainment devices,depending on the model purchased (see Key Charts,Mode Keyson the right).

The remote control requires four fresh AAA alkaline batteries (not included) and easy programming to co ntrol yo ur d evices. For best results,please read and perform all instructions listed here.Also,keep these instructions for future reference.

FEATURES AND FUNCTIONS

Use the Key Chartsto learn how to use the universal functions ofthe One For All 4 Devices Universal Remote Control.

Key Charts

Use SET for all

programming

sequences. The LED (red light)

blinks to show that the remote control is working and is sending signals.

Press POWER once to turn on or off the selected device.

Mode Keys for 4 Devices:

Press VCR,DVD,TV,or CBL/SATonce to sel ect

a home entertainment device to control.

Use the keypad (0~9) to directly select channels (for example, 09 or 31).

Press MUTE once to turn sound off or on.

Press PREV CH once to recall the last-viewed channel and to page back one screen on the main menu.

Press ENTER once after entering channel numbers on some T V models.

Use MENU (or EXIT) to choose options (or exit) from your selected device’s menu or guide.

Use VOL+(or VOL-) to raise (or lower) the sound volume.

Use CH+ (or CH-) to select the next higher (or lower) channel.

When co ntrolling a DVD player,use SKIP FORWARDto next DVD chapter.,use SKIP REVERSE to th e last DVD chapter.

Press SHIFT and use the Up/Down/Left Right cursor keys to move the cursor in the program guide and menu screens.

Press SHIFT and MUTE to select a m enu item.

Press SLEEP to activate your device’s sleep timer (not available for all devices).

Use the transport keys to control your VCR, CD or DVD player,or VOD. To record a program, press t h e record key (

REC

)

twice. use TV/VID to switch

the TV’s input to view TV or video program.

INSTALLING BATTERIES

1. On the remote control’s back,push the tab and lift offthe battery cover.

2. Obtain four (4) new AAA alkaline batteries.Match the + and – marks on the batteries to the + and – marks in the battery case,then insert the new batteries.

3. Press the battery cover back into place.The tab should click when the cover is locked.

4. Test the unit by pressing POWER and any mode key (e.g.,TV).If the batteries are inserted correctly,the LED will blink once.

NOTE:When batteries need replacement, the remote control will stop operating. Remove the old batteries and insert new ones within 30 minutes to ensure all of your programming information is restored.

PROGRAMMING DEVICE CONTROL

The One For All 4 Devices remote control is preprogrammed at the factory to operate an RCA TV and VCR,a Motorola (GI) cable box,and a Toshiba DVD player.To control devices other than the default brands,p er form the following steps;otherwise skip this section:

NOTE:For TV/VCR Combo control,see the next section.

1. Turn on a device (e.g.,VCR) and,if applicable, insert media, (e.g., cassette or disc).

NOTE:Please read steps 2-4 completely before proceeding.Highlight or write down the codes and device you wish to program before moving on to step 2.

2. On the remote control,press a device key once (i.e., VCR,DVD,TV,or CBL/SAT).Press and hold SETuntil the LED blinks twice,then release SET.

3. Use the Manufacturer’s Codes to locate the type of device and brand name and then enter the first fourdigit code for your component.If performed correctly,the LED will blink twice.

NOTE:If the LED did not blink twice,then repeat steps 2 through 3 and try entering the same code again.

4. Aim the remote controlat the device and press POWERonce.The device should turn off.If it does not respond, repeat steps 2-3,trying each code for your brand until you find one that works.Ifit still does not work,try

Searching For Your Code.

NOTE:If the de vice does not have a

POWER

key,press the (

5. Repeat steps 1 through 4 for each device you want to control.

PLAY

) key.

PROGRAMMING TV/VCR COMBO CONTROL

Perform the following instructions to control a TV/VCR Combo:

1. Turn on the TV/VCR Combo and insert a video cassette.

NOTE:Please read steps 2-4 completely before proceeding.Highlight or write down the codes and device you wish to program before moving on to step 2.

2. On the remote control,press VCR. Press and hold SET until the LED blinks twice,then release SET.

3. Use the Setup Codes For TV/VCR Combos (on the back side) to locate the brand name and then enter the first four-digit code for your device. Ifperformed correctly,the LED will blink twice.

NOTE:If the LED did not blink twice,then repeat steps 2 through 3 and try entering the same code again.

4. Aim the remote controlat the device and press POWERonce.It should turn off.If the device does not respond, repeat steps 2-3,trying each code for your brand until you find one that works.Ifit still does not work,try

Searching For Your Code.

NOTE:If the de vice does not have a

POWER

key,press the (

PLAY

) key.

SEARCHING FOR YOUR CODE

Ifyour device does not respond to the remote control after trying all codes listed for your brand,or if your brand is not listed at all,try searching for your code. For example,to search for a code for your TV:

1. On the remote control, press TV once.

2. Press and hold SET until the LED blinks twice,then release SET.

3. Enter9- 9 - 1.The LED will blink twice.

4. Aim the remote control at the the TV and slowly alternate between pressing POWER and TV.Stop when the TV turns off.

NOTE:In the search mode,the remote control will send IR codes from its library to the selected device,starting with the most popular code first.

5. To lock in the code,press and hold SET until the LED blinks twice,then release SET.

6. To search for the codes ofyour other devices,repeat steps 1 through 5,but substitute the appropriate device key for the device you are searching for.

CHECKING THE CODES

Ifyou have set up the remote control using the Searching For Your Code procedure,you may need to find out which four-digit code is operating your equipment:

For example,to find out which code is operating your TV:

1. On the remote control,press TV once.

2. Press and hold SET until the LED blinks twice,then release SET.

3. Enter9- 9 - 0.The LED will blink twice.

4. To view the code for the first digit, press 1 once.Wait 3 seconds,count the LED blinks (e.g.,3 blinks =3) and write down the number.

NOTE:Ifa code digit is “0”,the LED will not blink.

5. Repeat step 4 three more times for remaining digits.Use 2for the second digit,3for the third digit, and 4for the fourth digit.

6. To check for codes of other devices, repeat steps 1 through 5,but substitute the appropriate device key for each device you are checki ng . As before,write down each fourdigit code.

RE-ASSIGNING DEVICE KEYS

The One For All 4 Devices can be set to control a second TV,VCR,or DVD player.

For example,to control two TVs, a VCR, and a cable box,you will need to reassign the unused DVDkey to operate the second TV as follows:

1. On the remote control,press and hold SET until the LED blinks twice, then release SET.

2. Enter 9- 9 - 2.The LED will blink twice.

3. Press TVonce, then press DVDonce.

4. The DVDkey is now ready to be programmed for your second TV. See Programming Device Control.

To re-assign other device keys, repeat steps 1 through 4 by substituting the key sequence from the below chart for the most popular components:

To Re-Assign Key Sequence Perform

VCR as 2nd TV key: SET- 9 - 9 - 2

- TV - VCR

VCR as 2nd CBL key: SET- 9 - 9 - 2

- CBL/SAT - VCR

VCR as 2nd SAT key : SET- 9 - 9 - 2

- CBL/SAT - VCR

VCR as 2nd DVD key: SET - 9 - 9 - 2

- DVD - VCR

VCR back to VCR: SET- 9 - 9 - 2

- VCR - VCR

DVD as 2nd TV key: SET- 9 - 9 - 2

- TV - DVD

DVD as 2nd CBL key: SET- 9 - 9 - 2

- CBL/SAT - DVD

DVD as 2nd SAT key : SET- 9 - 9 - 2

- CBL/SAT - DVD

DVD as 2nd VCR key: SET - 9 - 9 - 2

- VCR - DVD

DVD back to DVD: SET- 9 - 9 - 2

- DVD - DVD

When a re-assignment is done,the LED will blink twice to confirm your choice. At that time,you will need to program the remote control for the new device (see Programming Device Cont rol).

CHANGING VOLUME LOCK

The One For All 4 Devices is set to control the volume ofyour TV in the TV, VCR, CBL/SAT,and DVD modes.If you want the volume to be controlled by a mode other than TV (e.g.,CBL/SAT), change the Volume Lock as fol l ows:

To Change Volume Lock To Another Mode:

1. On the remote control,press and hold SET until the LED blinks twice, then release SET.

2. Enter 9- 9 - 3 and then press any mode key once (except TV).The LED will blink twice.

3. Now,whenever you press VOL+, VOL–,or MUTE,volume will be controlled by your mode choice.

Unlocking Volume Control:

NOTE:Perform these instructions when you want independent volume control for each programmed device (e.g., TV volume control in TV mode,CBL/SAT volume control in CBL/SAT mode,etc.)

1. On the remote control,press and hold SET until the LED blinks twice, then release SET.

2. Enter 9- 9 - 3 and then press VOL+. The LED will blink four times.

3. Volume will again be controlled according to its default states.

TROUBLESHOOTING

For assistance, please contact us in any ofthe following ways:

• Consumer Help Line:(330) 405-8612

• Internet:http://www.onefo rall.com

PROBLEM: LED does not blink when

you press a key.

SOLUTION: Replace batteries with

AAA

four new

alkaline

batteries.

PROBLEM: LED blinks when you

press a key,but home entertainment component does not respond.

SOLUTION: Make sure the remote

control is aimed at your home entertainment device and is not farther than 15feet away.

PROBLEM: The unit does not control

home entertainment devices or commands are not working properly.

SOLUTION: Try all listed codes for the

component brands being set up.Make sure they can b e operated with a n infrared remote control.

PROBLEM: TV/VCR combo does not

respond properly.

SOLUTION: Use the VCR codes for

your brand.Some combo units may require both a TV code and a VCR code for full operat ion.

PROBLEM: Changing channels does

not work properly.

SOLUTION: If original remote control

required pressing ENTER to change channels,press ENTER on the remote control after enter ing the channel number.

PROBLEM: T ried “Search Method”

and still could not find a working code.

SOLUTION: Clear the device key as

follows: Press and hold SET until the LED blinks twice,then release. Next enter 9- 9- 2.Then press the device key to be cleared twice.Now repeat the “Search Method. ”

PROBLEM: CH

▲and CH▼ do not

work for your RCA TV.

SOLUTION: Due to RCA design (1983-

1987),only the original remote control will operate these functions.

PROBLEM: Remote control does not

turn on Sony or Shar p TV/VCR Combo.

SOLUTION: For power on,these prod-

ucts require programming TV codes.For Sony, use TV code 0000 and VCR code 0032.For Sharp,use TV code 0093 and VCR code 0048.

LIFETIME WARRANTY

One For ALL ("OFA") warrants this product to be free from defects in materials and workmanship, under normal use,throughout the period ofthe product’s ownership by the original purchaser.This warranty does not cover damage or failures caused by products or services not supplied by OFA,or which result from accident,misuses,abuse, neglect,mishandling,misapplication, faulty installation,set-up adjustment, improper maintenance,alteration,maladjustment of consumer controls,modi fications,commercial use,or that is attributable to acts ofGod.

There are no express warranties except as listed above.OFA SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF WARRANTY,ALL EXPRESS AND IMPLIED WARRANTIES,INCLUDING THE WARRANTIES OF MERCHANTABILIT Y AND FITNESS FOR A PARTICULAR PURPOSE,ARE LIMITED TO THE WARRANTY PERIOD SET FORTH AB OVE.S ome states do not allow the exclusion or limitation of incidental or consequential damagers,or limitations on how long an implied warranty lasts,so the above exclusions or limitations may not apply to you.This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

To obtain warranty service for a defective product,please return the product, preferably in the original carton,along with your purchase receipt,to the store oforiginal purchase for the first 90 days. A note detailing the complaint would b e helpful.The store,at its option,will replace or repair this product if found to be defective.

Ifthe unit has been purchased more than 90 days ago,pls return it to Impact Distribution Services,6262 Patterson Pass Road,Suite C,Livermore,CA 94550 together with the original receipt and $3.95 to cover postage and handling.It will be repaired or replaced at the manufacturer’s option.The manufacturer reserves the right to substitute a currently manufactured model with equal or superior features.

ADDITIONAL INFORMATION

ONE FOR ALL® is the registered trademark ofUniversal Electronics Inc. Computime International Ltd.is the Licensee ofthe ONE FOR ALL® brand for USA and Canada.

Copyright 2001 by Universal Electronics Inc.No part of this publication may be reproduc ed,transmitted,transcribed, stored in any retrieval system,or translated to any language,in any form or by any means,electronic,mechanical,magnetic,optical,manual,or otherwise, without the prior written permission of Universal Elec tronics In c.

One For All® 4 Devices is compatibile for use in North America excluding Me xico.

URC-4330 12/01