[1] CONFIRMATION AND UPGREAD OF THE FIRMWARE.......................................... D-2
1. THE CONFIRMATION PROCEDURE OF THE FIRMWARE .............................. D-2
2. UPGRADE PROCEDURE OF THE FIRMWARE ................................................ D-2
[2] STATUS INDICATION
1. PREPARATION FOR THE INDICATION ............................................................. D-3
2. STATUS INDICATION .........................................................................................D-3
D-1
Ver.1
Page 2
D. REPAIR PROCEDURE
X-3 / C-60ZOOM
[1] The confirmation and the upgrade of the firmware
1: The cofirmation procedure of the firmware
A lens barrier is opened under the condition that a card cover is opened. It confirms that the warning of “CARD-COVER
OPEN” is indicated on TFT, and a DISPLAY button and OK button are pushed at the same time. Open/close of the lens
barrier are done again after it waits for about ten seconds when it doesn't react to open/close of the barrier. ( When
warning isn't indicated on TFT. ) A firmware version is indicated on TFT when the buttons are pushed in the order of the
In case that BOOT AREA is upgraded : “S014xxxx.bin” is put in “dcolymp” folder of the xD picture card, and a camera is
turned on.
In case that USER AREA is upgraded : “E014xxxx.bin” is put in “dcolymp” folder of the xD picture card, and a camera is
turned on.
File name
xxxx.bin
S014
E014
xxxx.bin xxxx means a version number of the firmware.
2-1:
A “dcolymp” folder is made in the xD picture card that a format is done by X-3 / C-60ZOM. “E014xxxx.bin”
(or/and “S014xxxx.bin”) is/are put in “dcolymp” folder of the xD picture card. (xxxx means a version number of the firmware)
There is no limitation if it is a xD picture card which can be used with X-3 / C-60ZOM.
2-2:
An AC adapter is connected under the condition that the lens barrier is closed without the batteries. Then a the xD picture
card is inserted to the camera.
2-3:
A barrier is opened under the condition that OK button is pressed and held. When upgrade is started, red LED is turned
on. Then OK button is released.
2-4:
When upgrade is completed, red LED blinks.
2-5:
The firmware version is confirmed by above (1:).
D-2
Ver. 1
Page 3
X-3 / C-60ZOOM
D. REPAIR PROCEDURE
[2] Status indication
1: Preparation for the indication
1-1: In case of REC mode
A lens barrer is opened under the condition that AC adapter is connected and card door is opened. It confirms that the
warning of “CARD-COVER OPEN” is indicated on TFT, and a DISPLAY button and OK button are pushed at the same
time. The following information is indicated on TFT.
OLYMPUS
X-3
C-60Z Product Name
NTSC VIDEO-OUT (NTSC / PAL)
JPANESE LANGUAGE (JAPNESE / ENGLISH)
1-2: In case of PLAY mode
A DISPLAY button is pushed under the condition that AC adapter is connected and card door is opened. Under the
condition that warning is indicated on TFT, a zoom lever is operated with pushing OK button in the order of T
Center. Then OK button is released. The above information (1-1) is indicated on TFT.
→ W →
2: Status indication
It continues in 1-1 (or 1-2), the buttons are pushed in the order of (UP) → (DOWN) → (LEFT) →(RIGHT)
→ 1st Release → 2nd Release.
2-1: Firmware version
The following information is indicated on TFT when
Ex.)
PAG E1
B:1001
U:1001
C:1001
2-2: Release/Flash luminous number of times
The following information is indicated on TFT when
Ex.)
PAG E2
R:000026
S:000018
→(BOOT AREA: Ver1.001)
→ (USER AREA: Ver1.001)
→ (CISC : Ver1.001)
→(Release number of times)
→(Flash luminous number of times)
(UP) button is pushed after the above process.
(RIGHT) button is pushed.
2-3: Serial number
The following information is indicated on TFT when
Ex.)
PAG E3
CS : 176500607
MCS: 0042202000249001
→(Serial number of Body)
→(Serial number of MC-PCA2)
Ver.1
(DOWN) button is pushed.
D-3
Page 4
D. REPAIR PROCEDURE
X-3 / C-60ZOOM
2-4: Damage Code
The following information is indicated on TFT when (Arrow) button is pushed.
Ex.)
D:
1E13
→ (Damage Code)
XXXX
XXXX
XXXX
XXXX
XXXX
A damage code is indicated by four-digit hexadecimal after "D:", and a memory is done to five maximums. (A top tier is the
latest damage code.)
2-4-1: Detail of Damage Code (Refer to a damage code list.)
Ex.)1E 13 ----------- “Zoom Lens Reset Error”
Lower two digits Status(Row) 0 x 13
Upper two digits Status(Row) 0 x 1E
BlockStatusErrorDamageMedia
Error
0x06PARAMDT_NOT_SUPPORTEDB--Parameter injus tice or
0x07PARAMDT_OS_ERRORB--Queue R/W injust ice,
MEC_STATUS 0x1EXX
0x10MEC_RESLENS_FCS_ERROR---Focus Lens Reset
0x11MEC_RESLENS_ZOOM_ERROR---Zoom Lens Reset
0x12MEC_RESLENS_FCS_ERROR_DMGA--Focus Lens Reset
0x13MEC_RESLENS_ZOOM_ERROR_DMGA--Zoom Lens Reset
0x 20ME C_IRIS MOT_TIMER_DE LA YB--Iris Motor Timer Del ay
RECPROC_STATUS 0x1FXX
0x 21RECPROC_RECJPEG_ERROR---Unusual Paramet er
2-4-2: Erasure of the damage code
OK button is pushed under the condition that a damage code is indicated on TFT. Damage code is erased when a lens
barrier is closed.
Play
Mode
Not e
un-support
OS Error
Error
Error
Error
Error
D-4
Ver. 1
Page 5
X-3 / C-60ZOOM
r
(
)
(
y)
D. REPAIR PROCEDURE
DamageADamage mode indication
MediaMEDIA_OPENMEDIA_OPEN
A status is wr itten down by lower 16bit (0xXX).MEDIA_DPROTECT
DCIM dir is "Hidden"
DCIM dir is "Read-Onl y"
Writing error (File number)
Writing error (Root dir DCIM )
Abnomal parameter value
Can not over write "DCIM"
Interruption by the client
Dir can not found (Internal error)
Writing error (client judgment)
Writing error (client judgment)
Writing protect seal
Defect block number is over
File system error
Overlapping "c is"(SSFDC)
Others (Internal error)
Print reservation num ber is over 998
Abnomal com mand
[HDR] Section error (mount)
All frame is index print reservatin
Non frame is index print reservatin
Mix up for Index print reservation
frame and no reservation frame
Aautprint.mrk size over :It over
Image file error (Internal)
No capacity of media
No capacity of ROOT Dir
Writeing error "MISC"
Can not over write "MISC" (Hidden)
Can not over write "MISC" (ReadCan not over write "autprint.mrk"
Can not over write "autprint.mrk"
0x1a40 TAKE_PARAM_ERROR C
0x1a41 TAKE_QCREATE_ERR C
0x1a42 TAKE_EVCREATE_ERR C
0x1a43 TAKE_IVCREATE_ERR C
0x1a44 TAKE_EVWAIT_ERR C
0x1a45 TAKE_QREAD_ERR C
0x1a60 TAKE_TAKERDY_ABORT C
0x1a61 TAKE_TAKERDY_BATCHKERR C
0x1a80 TAKE_TAKEPIC_ABORT C
0x1a81 TAKE_TAKEPIC_NOTSTARTEDC
0x1a82 TAKE_TAKEPIC_BATCHKERR C
0x1a83 TAKE_TAKEPIC_NR_BUFF_ERRORC
PRM_STATUS0x1d00C
0x1d00 PARAMDT_CPRAM_OVER C
0x1d01 PARAMDT_FLASH_OVER1 C
0x1d02 PARAMDT_FLASH_OVER2 C
0x1d03 PARAMDT_BKEE_OVER1 C
0x1d04 PARAMDT_CHAIN_OVER C
0x1d05 PARAMDT_NOT_SUPPORTEDC
0x1d06 PARAMDT_OS_ERROR C
LENS_STATUS0x1e00C
0x1e00 LENS_FOCUS_STATUS C
0x1e00 LENS_FOCUS_RST_ERR C
0x1e01 LENS_FOCUS_RST_ERR_DMGA
0x1e10 LENS_ZOOM_STATUS C
0x1e10 LENS_ZOOM_RST_ERR C
0x1e11 LENS_ZOOM_RST_ERR_DMG A
0x1e12 LENS_ZOOM_SETUP_CANCELC
0x1e1A LENS_ZOOM_RECOVER_LD_ERR A
0x1e1B LENS_ZOOM_RECOVER_ZM_ERR A
0x1e20 LENS_APERTURE_STATUSC
0x1e20 LENS_APERTURE_RST_ERR C
0x1e21 LENS_APERTURE_RST_ERR_DMGB
0x1e22 LENS_APERTURE_SET_ERR C
0x1e23 LENS_APERTURE_SET_ERR_DMGB
Stop the Sequential Job by Interrupt
Command
Buffer over Reading error
Unknown Image fil e Ttpe
Unknown Image fil e Ttpe
Image file Type not JPEG(=RAW
OR TIFF
Thombnail Im age is "TIFF" file
OPE
"EXIF" Header er ror
(Damage) Parameter error
Queue cr eate err or
Event crea te error
IntrEvent create error
Event wait error
Queue read error
Take_Ready Abort Requested
Take_Ready Battery Empty
Take_Picture Abort Requested
Continue Comm and in Idling State
Take Picture Battery Empty
"CPRAM" Memory ov er
"FLASH" Memory over
FLASH (CAPTIVE TAG) MMemory
"BKRAM or EEROM"Memory over
"INDEX" Memory over
Illegal Parameter or Not Supported
Queue R/W error or Operation
S
Charging Time over
Charging Vltege over
Event Wait error
Event Wait Timeout error
Queue W ri teing Tim eout er ror
Event Wait Timeout error
Error Detection "STB" Popdown on
Flashin
Battery Em pty
Parameter error
Ver.1
D-9
Page 10
D. REPAIR PROCEDURE
r
g
(
)
p_
p
p
p
p
X-3 / C-60ZOOM
BlockStatusErrorDamageMedia
Erro
0x3003 JPEG_CODE_OVER C
0x3004 JPEG_UNABLE_DECODE C
0x3005 JPEG_HUFFMAN_ERROR C
0x3006 JPEG_DECODE_ERROR C
0x3007 JPEG_CNT_ERROR C
0x3008 JPEG_CORE_ERROR C
0x3009 JPEG_ENCODE_TIMEOUT_ERRORC
0x300a JPEG_DECODE_TIMEOUT_ERRORC
0x3081 JPEGHEAD_ERROR C
0x3082 BUFFER_ERROR C
0x3083 NOT_SUPPORTED C
0x3084 MULTI_SCAN C
0x3085 NOT_EXIST_SOI C
0x3086 UNKNOWN_MARKER C
0x3087 UNABLE_ANALYSIS C
0x3088 SCANDATA_BEFORE_SOS C
0x3089 MULTI_FRAME C
0x308a DQT_ERROR C
0x308b DHT_ERROR C
0x308c NOT_ANNEXK_HUFFMAN C
0x308d SOF_ERROR C
0x308e SOS_NS_ERROR C
0x308f SOS_TDTA_ERROR C
0x3090 SOS_SSSE_ERROR C
0x3091 SOS_AHAL_ERROR C
0x3092 SOS_LENGTH_ERROR C
0x3093 COMP_NUMBER_ERROR C
0x3094 NOT_MATCH_COMP_NUM C
0x3095 NOT_MATCH_CTABLE C
0x3096 NOT_AVAILABLE_QTABLE C
0x3097 NOT_AVAILABLE_HTABLE C
0x3098 DQT_PQTQ_ERROR C
0x3099 DHT_TH_ERROR C
0x309a DHT_TC_ERROR C
0x309b SOF_PNF_ERROR C
0x309c SOF_NF_ERROR C
0x309d SOF_TQ_ERROR C
0x309e SOF_LENGTH_ERROR C
0x30a0 DHT_LENGTH_ERROR C
0x30a1 DQT_LENGTH_ERROR C
0x30af HEADERSET_SUCCESS C
Play
Mode
Note
JPEG Code Limit over
Can Not Decode
Huffman error
JPEG Image Decode error
Control error
JPEG Drive error
JPEG Image Encode Timeout error
JPEG Image Decode Timeout error
JPEG Image Data error (Header)
Read Pointer Memory over
Image Data Not Supported
Image Type is Multi Scan Data
Not Exist "SOI" Initial Position
Unknown Marker
Unable Analysis
Scan data End but NO "SOS"
Multi Frame Type
"DQT" Data error
"DHT" Data error
Huffam Table "ANNEX K" Not
"SOF" Data error
"SOS Ns" Not Matching "SOF Nf "
"SOS Td","Ta" Step Across the
"SOS Ss","Se" Step Across the
"SOS Ah","Al" St ep Across the
"SOS" Length error
Compornent Num ber Overlay error
"SOF","SOS" Bi nary Number Not
Matchin
Not Matching Com pornent Table
Huf no Match
Not Available Queue Table
Not Available "H" Table
"DQT Pq,Tq" Step Across the
"DHT Th" Step Across the Bounds
"DHT Tc" Step Across the Bounds
"SOF P","Nf" St ep Across the
"SOF Nf" Step Across the Bounds
"SOF Tq" Step Acros s the Bounds
"SOF" Length error
"DHT" Length error
"DQT" Length error
Headr Set Success
FLASH_STATUS0x3100C
0x3101 FLASH_ID_INVALID C
0x3102 FLASH_LENGTH_INVALIDC
0x3103 FLASH_ERASE_FAIL C
0x3104 FLASH_WRITE_FAIL C
0x3105 FLASH_E_ADR_INVALID C
0x3106 FLASH_LOCK_FAILC
0x3107 FLASH_WRITE_PROTECT C
0x3108 FLASH_UNKNOW N_MODE C
0x3109 FLASH_LOCK_MISMATCHC
0x310a FLASHMEM_INIT_FAIL C
0x310b FLASHMEM_WRITE_FAILC
0x3900 PLAYEDIT_ABORTEDC
0x3901 PLAYEDIT_NOT_SUPPORT C
0x3902 PLAYEDIT_MEDIA_FULL C
0x3903 PLAYEDIT_NO_ORIENTATIONC
0x3904 PLAYEDIT_NOT_JPEG C
0x3905 PLAYEDIT_ALIGN_ERROR C
0x3906 PLAYEDIT_MEMORY_OVER C
MPEG File Playback Command
Aborted
Can Not Open MPEG File by
over
Memor
Command Not Supported
Can Not Find Thumbnail for MPEG
e File
Ima
MPEG Data Fail error
Media Full on MPEG Index Created
No Memory for Open MPEG File
Command Dediance by Recording
now
Can Not Open MPEG File by Disk
Abort Com mand
Not Supported Comm and
Can Not Edit for Medit Full
No "Orientation Tag" Value
Not JPEG File
Buffer Memory Align error
No Memory for Edit
Command Not Supported
Queue Cr eate err or
Event Cr eate err or
Semaphore Create error
Not O pen erro r
Memory error
Command Not Supported
Event Cr eate err or
Interrupt Event Create error
Command Not Supported
Event Cr eate err or
Interrupt Event Create error
Status Phase Not Supported
Command Not Supported
Queue Cr eate err or
Event Cr eate err or
Interrupt Event Create error
Semaphore Create error
Not O pen erro r
Memory error
Command Not Supported
Frame Type Not Supported
Command Not Supported
Event Cr eate err or
Interrupt Event Create error
Not O pen erro r
Frame Status Type Not Supported
Frame Status Queue Full
0xBB00 TPC_ERR_BUS_RESET C
0xBB01 TPC_ERR_BUS_REMOVEDC
0xBB02 TPC_ERR_ABORT C
0xBB03 TPC_ERR_HDD_OVER C
PER_TIMER_STATUS0x5200C
0x5201 PER_TIMER_SETLEVEL_ERR C
0x5202 PER_TIMER_SET_ERR C
TIMERDRV_STATU0x5300C
PER
0x5301 PER_TIMER08_BUSY C
0x5302 PER_TIMER16_BUSY C
0x5303 PER_TIMERGIO_BUSY C
0x5304 PER_TIMER08_MODEERR C
0x5305 PER_TIMER16_MODEERR C
0x5306 PER_TIMERGIO_MODEERR C
0x5307 PER_TIMERDRV_GIOID_ERRC