
B. DISASSEMBLY AND ASSEMBLY PROCEDURE X-350/D-575ZOOM/C-360ZOOM
B. DISASSEMBLY AND ASSEMBLY
PROCEDURE
[1] REMOVAL OF CABINET BACK, LCD, CABINET FRONT AND TB1 BOARD.......B-2
[2] REMOVAL OF TB2 BOARD AND CP1 BOARD......................................................B-3
[3] REMOVAL OF LENS UNIT AND ST1 BOARD........................................................B-3
[4] ASSEMBLY OF LENS UNIT AND VIEWFINDER ...................................................B-4
[5] BOARD LOCATION.................................................................................................B-4
B-1 Ver.1

B. DISASSEMBLY AND ASSEMBLY PROCEDURE X-350/D-575ZOOM/C-360ZOOM
[1] REMOVAL OF CABINET BACK, LCD, CABINET FRONT AND TB1 BOARD
Disassembly perform as follows and assembly perform by reversing the disassembly steps.
Be sure to discharge the main capacitor, then continue to disassembling.
! Beware of electric shock
Danger of electric shock.
Use a discharging tool to remove
the electrical charge before working.
1. Open the cover DC.
2. Open the cover card
3. Seven screws 1.7 x 4
4. Cabinet back
5. FPC
6. Discharge
7. Connector
8. FPC
9. LCD
10. Two screws 1.7 x 5
6
The lead free solder is applied to this product.
!
11. Holder monitor
12. Two screws 1.7 x 5
13. Cover jack
14. Stand
15. Connector
16. Cabinet front
17. Three screws 1.7 x 4
18. TB1 board
19. Shield button
Use the lead free solder in working.
Notice
1
3
2
19
10
C
18
B
17
12
15
5
A
8
7
4
9
11
C
A
B
13
3
14
16
3
B-2 Ver. 1

B. DISASSEMBLY AND ASSEMBLY PROCEDUREX-350/D-575ZOOM/C-360ZOOM
[2] REMOVAL OF TB2 BOARD AND CP1 BOARD
1. Three screws 1.7 x 3.5
2. Three screws 1.6 x 3.5
3. Two FPCs
4. Remove the solder.
5. Remove the solder.
6. Microphone
7. Screw 1.7 x 3.5
8. TB2 board
9. Remove the solder.
10. CP1 board
TB
CP
ST1
10
CP1
1
1
red
3
black
black
2
red
5
4
3
9
blue
yellow
black
white
yellow
[3] REMOVAL OF LENS UNIT AND ST1 BOARD
1. Three screws 1.6 x 5
2. Lens unit
3. Screw 1.6 x 3.5
4. Finder
5. Remove the solder.
6. Piezo buzzer
7. Two screws 1.7 x 3.5
8. Screw 1.7 x 3.5
9. ST1 board
10. Holder chassis
11. Reflector self
4
3
8
blue
10
11
6
black
white
7
7
9
gray
8
red
5
black
6
black
red
1
2
B-3 Ver. 1

B. DISASSEMBLY AND ASSEMBLY PROCEDURE X-350/D-575ZOOM/C-360ZOOM
[4] ASSEMBLY OF LENS UNIT AND VIEWFINDER
1
1. Rotate F-Gear to move F-Lens to the set-down position.
2. Rotate F-Gear to the cut position.
3. Insert a pin to keep F-Cam position.
4. Set the Viewfinder to the Lens unit and tighten a screw.
5. Confirm the position of F-Gear and Idle-Gear.
2
Rotet F-Gear
Viewfinder (back side)
[5] BOARD LOCATION
3
Insert a pin
Viewfinder (back side)
ST1 board
5
Viewfinder and Idle-Gear (front side)
CP1 board
TB1 board
TB2 board
B-4 Ver. 1