Oliver 6303 Owner's Manual

6303 6” x 89” Oscillating Edge Sander

Owner’s Manual

Oliver Machinery M-6303 06/2017

Seattle, WA  Copyright 1999-2017
[e-mail] www.olivermachinery.net

GROUNDING INSTRUCTIONS

1. All grounded, cord-connected tools: in the event of a malfunction or breakdown, grounding
provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is
equipped with an electric cord having an equipment grounding conductor and a grounding plug. The
plug must be plugged into a matching outlet that is properly installed and grounded in accordance with
all local codes and ordinances.

Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a
qualified electrician. Improper connection of the equipment grounding conductor can result in a risk of
electric shock. The conductor with insulation having an outer surface that is green with or without yellow
stripes is the equipment-grounding conductor. If repair or replacement of the electric cold or plug is
necessary, do not connect the equipment-grounding conductor to a live terminal.

Check-with a qualified electrician or service personnel if the grounding instructions are not
completely understood or if in doubt as to whether there tool is properly grounded. Use only 3-wire
extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool’s plug.
Repair or replace damage or worn cord immediately.

2. Grounded, cord-connected tools intended for use on a supply circuit having a nominal rating
less than 150 volts. This tool is intended for use on a circuit that has an outlet that looks like the one
illustrated in Sketch A in Figure the tool has a grounding plug that looks like the plug illustrated in
Sketch A in Figure A temporary adapter, which looks like the adapter illustrated in Sketches B and C,
may be used to connect this plug to a 2-pole receptacle as shown in Sketch B if a properly grounded
outlet is not available. The temporary adapter should be use only until a properly grounded outlet can
be installed by a qualified electrician. The green-colored rigid ear, plug, and the like extending from the
adapter must be connected to a permanent ground such as a properly grounded outlet box.

3. Grounded, cord-connected tools intended for use on a supply circuit having a nominal rating
between 150-250 volts, inclusive: This tool is intended for use on a circuit that has an outlet that looks
like the one illustrated in Sketch D in Figure. The tool has a grounding plug that looks like the plug
illustrated in Sketch D.

Make sure the tool is connected to an outlet having the same configuration as the plug. No
adapter is available or should be used with this tool. If the tool must be reconnected for use on a
different type of electric circuit, the reconnection should be made by qualified service personnel; and
after reconnection, the tool should comply with all local code and ordinances.

WARNING

Safety Note: Thoroughly Read Instruction Manual Prior to Operating Sander

1. WEAR eye protection.

2. SUPPORT work piece with backstop or worktable.

3. KEEP GUARDS IN PLACE and in working order.

4. REMOVE ADJUSTNG KEYS AND WRENCHES. Form habit of checking to see that keys and
adjusting wrenches are removed from tool before turning it on.

5. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

6. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tool in damp or wet locations,
or expose them to rain. Keep work area well lit.

7. KEEP CHILDREN AWAY ALL visitors should be kept safe distance from work area.

8. MAKE WORKSHOP KID PROOF with padlocks, master switches, or by re moving starter keys.

9. DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was designed.

10. USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed.

11. WEAR PROPER APPAREL. Wear no loose clothing, gloves, neckties, rings, bracelets, or other
jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear
protective hair covering to contain long hair. Exception: the reference to gloves may be omitted
from the instructions for a grinder.

12. ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty.
Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses.

13. SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your
hand and it frees both hands to operate tool.

14. DON’T OVERREACH. Keep proper footing and balance at all times.

15. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance.
Follow instructions for lubricating and changing accessories.

16. DISCONNECT TOOLS before servicing changing accessories, such as blades, bits, cutters,
and the like.

17. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position
before plugging in.

18. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recommended
accessories. The use of improper accessories may cause risk of injury to persons.

19. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is
unintentionally contacted.

20. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is
damaged should be carefully checked to determine that it will operate properly and perform its
intended function – check for alignment of moving parts, binding of moving parts, breakage of
parts, mounting, and any other conditions that may affect its operation. A guard or other part
that is damaged should be properly repaired or replaced.

21. DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the
blade or cutter only.

22. NEVER LEAVE TOOL RUNNING UNATTENDED, TURN POWER OFF. Don’t leave tool until it
comes to a complete stop.

3

HEX NUT

WASHER

SPRI NG WASHER

5/16 Hex. Hd. Scr

A

B

Fig: 1 Fig: 3

The way to change sand band

Fig: 2 Fig: 4

1. STAND ASSEMBLY : CLAMP PART(A)
AND PART(B) BY HEX NUT , WASER,
SPRING WASER AND SCREW. SEE.FIG.1

2. STAND ASSEMBLY ,SEE FIG.2

1. SANDING TABLE CAN BE ADJUSTED 90°－
180° ,SEE FIG.4

2. ADJUS T CLAMP HANDLE (B) AT DE SIRED TO
CHANGE NEW BELT. SEE FIG.4

3. LOOSEN ANGLE LOCK KNOB(A) TO SET AND
TIGHTEN THE ANGLE.