NEC E656 User Guide
User’s Manual
E656
E556
E506
E436
E326
Please nd your model name in the label on the backside of monitor.
Index
Precautions And Reminders ................................................................ English-1
Important Safety Instructions ............................................................... English-2
Important Information .......................................................................... English-5
Declaration Of Conformity ..................................................................English-11
Contents ............................................................................................ English-13
Preparation ........................................................................................ English-14
Attaching the Base .................................................................. English-14
Using Cable Clamper .............................................................. English-15
Preparing Your LCD TV For Wall Mounting (optional) ............. English-15
Prohibit Portrait Condition Use ................................................ English-16
Place The TV On A Solid Surface ...........................................English-17
Antenna Connection ................................................................ English-17
Battery Installation and Replacement...................................... English-18
Connect To The Power Source ...............................................English-18
Power On/Off Your New LCD TV ............................................ English-19
Power Mode Status ................................................................. English-19
Source Connection Guide ....................................................... English-22
Operating Instructions ....................................................................... English-25
Using The Side Panel Controls ............................................... English-25
Using The Remote Control ...................................................... English-26
Operating Range for the Remote Control................................ English-27
Timing Table ............................................................................ English-28
Navigating The On-Screen Menu ...................................................... English-29
Video Menu ............................................................................. English-29
Audio Menu ............................................................................. English-30
Channels Menu ....................................................................... English-30
Setup Menu ............................................................................. English-31
USB Menu ............................................................................... English-33
USB Demo Mode .................................................................... English-36
Maintenance and Recycling .............................................................. English-37
Care Of The Screen ................................................................ English-37
Mobile Telephone Warning ...................................................... English-37
End Of Life Directives.............................................................. English-37
Manufacturer’s Recycling and Energy Information ............................ English-38
Disposing of your old NEC product ......................................... English-38
Energy Saving ......................................................................... English-38
Product Specication ......................................................................... English-39
RS-232C Port Specications ................................................... English-45
Supporting HDMI CEC command ........................................... English-46
Before Calling Service ....................................................................... English-47
Glossary ............................................................................................ English-48
www.necdisplaysolutions.com
Precautions And Reminders
Do not place the TV in
conned spaces or in a
box when in use. Maintain
ample ventilation for the
TV when in use.
Keep the TV away from
direct sunlight, dust,
humidity, smoke and oily
areas.
Unplug the AC cord from
the AC outlet before
cleaning. Do not use
liquid cleaners or aerosol
cleaners to clean the TV.
Do not open the TV
cabinet.
Unplug immediately if the
TV falls.
Do not place the TV near
water such as a bathtub,
washbasin, sink, laundry
tub, swimming pool, or a
damp basement.
Unplug immediately if the
TV has been exposed to
rain or water.
Call a NEC certied
service personnel for any
internal service needed for
your TV.
Unplug immediately if
there is a TV malfunction
such as a loss of audio /
video, the presence of
smoke, or a bad odor
coming from the TV.
Do not cover or block
any vents or openings.
Inadequate ventilation may
shorten the life of the TV
and cause overheating.
English
Place the unit on a sturdy,
even surface.
Do not inser t any foreign
objects into the TV
cabinet.
Unplug immediately if
objects have fallen into the
monitor.
Notice for Remote Controller
Avoid Liquids
PRE CH
CH-List
Avoid Aerosol Cleaners
PRE CH
CH-List
English-1
Unplug the power cord
from the outlet when the
TV is not in use for long
periods of time (days).
Avoid Dropping
PRE CH
CH-List
Important Safety Instructions
Read before operating equipment
Follow all warnings and instructions marked on this TV.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided
plug does not t into your outlet, consult an electrician for replacement of
the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. Only use attachments / accessories specied by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specied by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from
tip-over.
13. Unplug this apparatus during lightning storms or when unused for long
periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required
when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped. Unplug
immediately if the monitor faces above condition.
15. The TV complies with the recommended safety standards for stability.
Do not put excessive force on the front or top of the cabinet. This could
cause the product to tip over and cause damage and / or personal injury.
16. If monitor or glass is broken, do not come in contact with the liquid crystal
and handle with care.
S3125A
17. Follow instructions for wall, shelf or ceiling mounting as recommended by
the manufacturer.
18. An outdoor antenna should not be located near overhead power lines or
any electrical circuits.
19. If an outside antenna is connected to the receiver, conrm that the
antenna system is grounded to protect against voltage surges and built
up static charges. Section 810 of the National Electric Code, ANSI /
NFPA No. 70-1984, provides information with respect to proper grounding
for the mast and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding connectors, location of antenna
discharge unit, connection to grounding electrodes and requirements for
the grounding electrode.
20. Rest your eyes periodically by focusing on an object at least 5 feet away.
Blink often.
21. Do not place any heavy objects on the power cord.
Damage to the cord may cause shock or re.
22. Do not use monitor in high temperature, humid, dusty, or oily areas.
23. Do not bend, crimp or other wise damage the power cord.
24. Apparatus shall not be exposed to dripping or splashing and no objects
lled with liquids, such as vases, shall be placed on the apparatus.
NOTE: To the TV system installer: This reminder is provided to call attention
to Article 820-44 of the National Electric Code that provides guidelines for
proper grounding and, in particular, species that the cable ground shall be
connected to the grounding system of the facility, as reasonably close to the
point of cable entry as possible
English
English-3English-2
WARNING: To prevent the apread of re, keep candles or other
open ames away fram this product at all times.
If a television is not positioned in a sufciently stable location, it can be
potentially hazardous due to falling. Many injuries, particularly to children,
can be avoided by taking simple precautions such as:
• Using cabinets or stands recommended by the manufacturer of the
television.
• Only using furniture that can safely support the television.
• Ensuring the television is not overhanging the edge of the supporting
furniture.
• Not placing the television on tall furniture (for example, cupboards or
bookcases) without anchoring both the furniture and the television to a
suitable support.
• Not standing the televisions on cloth or other materials placed between
the television and supporting furniture.
• Educating children about the dangers of climbing on furniture to reach
the television or its controls.
WARNING: To prevent injury, this apparatus must be securely attached to
the oor/wall in accordance with the installation instructions.
IMPORTANT INFORMATION
Important Information
WARNING
TO PREVENT FIRE OR SHOCK HA ZARDS, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S
POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR
OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH
VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE
POWER CORD IS UNPLUGGED FROM WALL SOCKET.
TO FULLY DISENGAGE THE POWER TO THE UNIT,
PLEASE DISCONNECT THE POWER CORD FROM THE AC
OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the
unit may have sufcient magnitude to cause electric shock.
Therefore, it is dangerous to make any kind of contact with any
part inside this unit.
This symbol alerts the user that important literature concerning
the operation and maintenance of this unit has been included.
Therefore, it should be read carefully in order to avoid any
problems.
English
CAUTION: Please use the power cord provided with this TV in accordance
with the table below. If a power cord is not supplied with this equipment,
please contact your supplier.
Pl u g Type Plug Shape Region Voltage
North America
English-5English-4
U.S.A./Canada AC 120 V
Power source
This LCD TV operates on 120 volts 60 Hz, AC current. Insert the power cord
into a 120 volts 60 Hz outlet. The mains plug is used as the disconnect device
and shall remain readily operable.
To prevent electric shock from the TV, do not use with an extension cord,
receptacle, or other outlet unless the blades and ground terminal can be fully
inserted to prevent blade exposure.
Never connect the LCD TV to 50 Hz, direct current, or anything other than the
specied voltage.
CAUTION:
Never remove the back cover of the LCD TV as this can expose you to very
high voltages and other hazards. If the TV does not operate properly, unplug
the LCD TV and call your authorized dealer or service center.
Adjust only those controls that are covered in the instructions, as improper
changes or modications not expressly approved by NEC could void the
user’s warranty.
Batteries installed warning
CAUTION: Incorrect usage of batteries can result in leaks or bursting.
NEC recommends the following battery use:
• Do not mix battery brands.
• Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type.
• Do not combine new and old batteries. This can shorten the battery life
or cause liquid leakage of the batteries.
• Remove dead batteries immediately to prevent battery acid from leaking
into the battery compartment.
• Do not touch exposed battery acid as it may injure skin.
• Remove the batteries if you do not intend to use the remote control for a
long period of time.
• The batteries shall not be exposed to excessive heat such as sunshine,
re or the like.
Image persistence
• Please be aware that LCD Technology may experience a phenomenon
known as Image Persistence.
Image Persistence occurs when a residual or “ghost” image of a
previous image remains visible on the screen.
Unlike CRT monitors, LCD monitors’ image persistence is not
permanent, but constant images being displayed for a long period of
time should be avoided.
To alleviate image persistence, turn off the monitor for as long as the
previous image was displayed.
For example, if an image was on the monitor for one hour and a residual
image remains, the monitor should be turned off for one hour to erase
the image.
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS
recommends displaying moving images and using a moving screen saver at
regular intervals whenever the screen is idle or turning off the monitor when
not in use.
CAUTION:
These servicing instructions are for use by qualied service personnel only.
To reduce the risk of electric shock, do not perform any servicing other than
that contained in the operating instructions unless you are qualied to do so.
Ventilation
The slots and openings in the TV are provided for necessary ventilation. To
ensure reliable operation of the TV and to protect it from overheating, these
slots and openings must never be blocked or covered.
Unless proper ventilation is provided, the TV may gather dust and get dirty.
For proper ventilation, observe the following:
• Do not install the TV face up, down or sideways.
• Do not install the TV turned over or upside down.
• Never cover the slots and openings with a cloth or other materials.
• Never block the slots and openings by placing the TV on a bed, sofa,
rug or other similar surface.
• Never place the TV in a conned space, such as a bookcase or built-in
cabinet, unless proper ventilation is provided.
Leave some space around the TV set as shown below. Otherwise, aircirculation may be inadequate and will cause overheating, which may cause
a re or damage to the TV set.
English
English-7English-6
Install on the wall
10 cm
11 7/8 inches
30 cm
4 inches
10 cm
4 inches
2.36 inches
4 inches
10 cm
Leave at least this space
around the set.
6 cm
For use only with UL Listed Wall Mount Bracket with minimum weight / load:
Please refer to the Specication on page 40 and page 43 .
Unit without base weight: The equipment and its associated mounting means
still remain secure during the test.
Used wall mounting kit, VESA-compatible wall bracket distance, diameter of
Screw dimension: Please refer to the Specication on page 40 and
page 43 .
Installed with stand
11 7/8 inches
30 cm
4 inches
10 cm
4 inches
10 cm
Leave at least this space
around the set.
4 inches
10 cm
Never install the TV set where air-circulation is blocked.
Objects and ventilation holes
Never push objects of any kind into the TV through the cabinet slots as they
may touch dangerous voltage points or short out parts that could result in a
re or an electric shock. Do not place any objects on the TV.
English
English-9English-8
License Notice and Trademark
®
Acknowledgement
Windows is a registered trademark of Microsoft Corporation.
NEC is a registered trademark of NEC Corporation.
All other brands and product names are trademarks or registered
trademarks of their respective owners.
The terms HDMI and HDMI HighDenition Multimedia Interface, and
the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing
Administrator, Inc. in the United States
and other countries.
Manufactured under license from Dolby
Labortories. Dolby and the double-D
symbol are trademarks of Dolby
Laboratories.
HDCP (High-bandwidth Digital Content Protection): HDCP is a system for
preventing illegal copying of video data sent over a digital signal. If you are
unable to view material via the digital input, this does not necessarily mean
the display is not functioning properly. With the implementation of HDCP,
there may be cases in which certain content is protected with HDCP and
might not be displayed due to the decision/intention of the HDCP community
(Digital Content Protection, LLC).
[Notice] About the MPEG AVC license included in this product
MPEG AVC
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO
LICENSE.
SUCH LICENSE EXTENDS TO THIS PRODUCT ONLY AND ONLY
TO THE EXTENT OF OTHER NOTICES WHICH MAY BE INCLUDED
HEREIN. THE LICENSE DOES NOT EXTEND TO ANY OTHER
PRODUCT REGARDLESS OF WHETHER SUCH PRODUCT IS
INCLUDED WITH THIS LICENSED PRODUCT IN A SINGLE ARTICLE.
ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C.
SEE HTTP://WWW.MPEGLA.COM
Declaration Of Conformity
This device complies with Part 15 of FCC Rules. Operation is subject to the
following two conditions. (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
U.S. Responsible Party: NEC Display Solutions of America, Inc.
Address: 500 Park Boulevard, Suite 1100
Tel. N o.: (630) 467-3000
Type of Product: LCD TV
Equipment Classication: Class B Peripheral
Model: E656
conforms to the technical standards as specied in the FCC Rules.
Canadian Department of Communications Compliance Statement
DOC: This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety
Regulations according to CAN/CSA C22.2 No. 60065-03.
Itasca, Illinois 60143
E556
E506
We hereby declare that the equipment specied above
E436
E326
English
En g l i sh-11English-10
FCC Information:
1. Use the attached specied cables with the E656 / E556 / E506 / E436
/ E326 color monitor so as not to interfere with radio and television
reception.
(1) Please use the supplied power cord or equivalent to ensure FCC
compliance.
(2) Please use the supplied shielded video signal cable, Mini D-SUB 15
pin to Mini D-SUB 15 pin.
2. This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult your dealer or an experienced radio / TV technician for help.
FCC CAUTION
To assure continued compliance and possible undesirable interference,
ferrite cores may be used when connecting this LCD TV to video equipment;
and maintain at least 400mm spacing to other peripheral device.
FCC warning
Changes or modications not expressly approved by the party responsible for
compliance with the FCC Rules could void the user’s authority to operate this
equipment.
Cables
Connections to this device must be made with shielded cables with metallic
RF / EMI connector hoods to maintain compliance with FCC Rules and
Regulations.
Canadian notice
CAN ICES-3 (B) / NMB-3(B)
Analog and Digital Television Receiving Apparatus — Appareil de réception
de télévision analogique et numérique, Canada BETS-7 / NTMR-7
If necessary, the user should contact the dealer or an experienced radio/
television technician for additional suggestions. The user may nd the
following booklet, prepared by the Federal Communications Commission,
helpful: “How to Identify and Resolve Radio-display Interference Problems.”
This booklet is available from the U.S. Government Printing Ofce,
Washington, D.C., 20402, Stock No. 004-000-00345-4.
Contents
Your new NEC monitor box*1 should contain the following:
• Monitor (1)
• Remote control (1)
• 1.5 V AAA batteries (2)
• Power cord (1)
• D-sub cable (1)
• User’s manual (1)
E656 / E556 / E506 / E436 / E326
English
Wireless Remote Control
and AAA Batteries
Video Signal Cable
(Mini D-SUB 15 pin to
Mini D-SUB 15 pin)
Power Cord
User’s Manual
User’s Manual
NOTE:
*1: Remember to save your original box and packing material to transport or
ship the monitor.
*2: The following stand base and screw are option parts.
E656: M6 (30mm) x 4
(E656)
(E556/E506/E436/E326)
Stand Base
E556/E506: M6 (22mm) x 4
E436/E326: M4 (20mm) x 4
Stand Screw
English-13English-12
Loading...