Nec DSX-80 DEMO KIT QUICK START GUIDE
16ESIU
PCB
8SLIU
PCB
8COIU
PCB
Power
Supply
CPU
DSX-80 Demo Kit Quick Start Guide
DSX-80 Cabinet
Power
Power
Supply
Supply
Optional
DSX IntraMail
8-Conductor
P/N 80891
Cable
CPU
CPU
back of unit
16ESIU
16ESIU
PCB
PCB
8SLIU
8SLIU
PCB
PCB
8COIU
8COIU
PCB
PCB
Adaptor
P/N 80890
1093096 - 56
To Electrical
Service Ground
Always check www.necdsx.com for the
Important
latest system software updates.
Dedicated
Surge
Protector
AC Outlet
302
301
Making Lines Ring
To ring this line: Do this:
Line 1 Press INTERCOM and dial 316
Line 2 Press INTERCOM and dial 317
Line 3 Press INTERCOM and dial 318
Line 4 Press INTERCOM and dial 319
300
Important
These instructions are for reference only. Do
not install the system without first reading
the Hardware Manual.
Basic Installation Layout
Default Features
All lines are loop start DTMF.
1.
• Use 3101-01: Line Type to change this assignment.
• Lines 1-12 ring on line keys 1-12 for extensions 300-315. (Lines 13-64 do not appear on line keys.)
2.
• All other extensions are lamp only for lines 1-12.
To customize line ringing, use one of the following:
3.
• User Programmable Features code
• Use 2132-[01-64]: Line Ringing .
1.
The circuit types for keyset extensions are automatically set when the extension is plugged in.
Keyset users can place outside calls by:
• Pressing a line key and dialing the outside number. (See the Central Office Calls, Placing feature for more.)
2.
• Pressing
• Line Dial-Up and Direct Line Access are disabled. (See the Central Office Calls, Placing feature for more.)
All extensions have full incoming and outgoing access to all outside lines.
3.
• See Initial Startup Programming below to change this assignment.
INTERCOM
Default Features for Lines
#RAL
. (See the User Programmable Features feature for more.)
Default Features for Extensions
, dialing 9, then dialing the outside number. (See the Line Group Routing feature for more.)
4.
By default, Feature Keys 1-12 are line keys. Keys 13-24 are undefined. See the Feature Keys feature for more.
Default Features for IntraMail
1.
Each extension has an IntraMail voice mailbox.
2.
All mailboxes are enabled. To disable a mailbox, see 2141-01: Station Mailbox Type .
3.
The IntraMail Automated Attendant does not answer outside calls. (See the Automated Attendant feature for more.)
Initial Startup Programming
1. Enter the programming mode.
1.
From any display telephone, press
The system passwords are:
2.
-
632379 (NECDSX)
for Installer (level 3),
Administrator 1 (level 1).
2. Assign the correct circuit type to each of your installed lines.
1.
In 3101-01: Line Type , assign the line circuit type (e.g., enter
2.
In 3103-03: DTMF Dialing , normally enter
3. By default, each extension has full incoming and outgoing access to each line. To change this assignment:
1.
In 2131-[01-64]: Line Access , change each extension’s line access as required. The options are:
-
0
for no access,
2.
Using 902x-Copy may save you time.
1
for incoming access only,
INTERCOM
1
(or press Feature Key 2) for DTMF dialing.
+ Dial
#*#*
+ Enter the system password +
9999
for System Administrator 2 (level 2),
1
or press Feature Key 2 for loop start).
2
for outgoing access only,
3
for full access
HOLD.
0000
for System
4.
By default, extensions 300-315 ring immediately day and night for lines 1-12. To change this assignment:
1.
In 2132-[01-64]: Line Ringing , set the ringing option for each extension, The options are:
-
0
for lamp only (no ringing) day and night,
ringing day and night
2.
Using 902x-Copy may save you time.
5. To change the default system passwords:
1.
Turn to the System Programming Password Protection feature for more about system passwords.
(1093068)
November 10, 2006, Rev 3
Printed in U.S.A.
1
for day and night ringing,
Empowered by Innovation
2
for night ringing only,
3
for delay
Loading...