NEC DSX-40 User Manual
DSX-40 Quick Start Guide
DSX-40 Cabinet
Extensions
300-303 Shown
RJ61X
5
4
3
1
1093067 - 1
6
2
7
1
8
1
1
2
3
4
25-PAIR CABLE
COLOR
CODE
WHT-BLU
BLU-WHT
WHT-ORN
ORN-WHT
WHT-GRN
GRN-WHT
WHT-BRN
BRN-WHT
66M1-50 Block
Optional
DSX IntraMail
Cable 1
Cable 2
Cable 3
1
2
5
6
Cable 1
FUNCTIONRJ61X
300 T
300 R
301 T
301 R
302 T
302 R
303 T
303 R
3
4
5
2
3
6
Cable 2
BLOCK
TERM
1
2
3
4
5
6
7
8
4
5
6
Modular
Jack
Cable 3
YEL
BLU-WHT
RED
625
Installation Cable
To electrical
service ground
BLK
GRN
Protector
P/N 808920
WHT-BLU
Always check www.necdsx.com for the
latest system software updates.
Dedicated
Surge
AC Outlet
1
Extensions 324-325 Shown
25-PAIR CABLE
COLOR
CODE
5
WHT-BLU
4
BLU-WHT
3
WHT-ORN
6
1
2
7
1
8
ORN-WHT
WHT-GRN
GRN-WHT
WHT-BRN
BRN-WHT
66M1-50 Block
DSX Keyset
Important
Lines 1-4 Shown
25-PAIR CABLE
COLOR
CODE
5
WHT-BLU
4
BLU-WHT
3
WHT-ORN
6
ORN-WHT
2
WHT-GRN
7
GRN-WHT
1
WHT-BRN
8
BRN-WHT
66M1-50 Block
FUNCTIONRJ61XRJ61X
324 T
324 R
325 T
325 R
BLOCK
TERM
1
2
3
4
5
6
7
8
BLU-WHT
Analog
YEL
RED
FUNCTIONRJ61XRJ61X
1 T
1 R
2 T
2 R
3 T
3 R
4 T
4 R
BLOCK
TERM
1
2
3
4
5
6
7
8
To Telco
BLK
WHT-BLU
GRN
625
Modular
Jack
Latch
faces up
80000 - 18C
8-Pin (RJ61X)
Jack Pinouts
RJ61X
Pin
1
2
3
4
5
6
7
8
Note
reversal
Port
Designation
4T
3T
2T
1R
1T
2R
3R
4R
To 66 Block
WHT-BLU (1T)
BLU-WHT (1R)
WHT-ORN (2T)
ORN-WHT (2R)
WHT-GRN (3T)
GRN-WHT (3R)
WHT-BRN (4T)
BRN-WHT (4R)
Basic Installation Layout
Important
These instructions are for reference only.
Do not
install the system without first
reading the Hardware Manual.
Default Features
All lines are loop start DTMF.
1.
• Use
• Lines 1-8 ring on line keys 1-8 for extensions 300-315.
2.
• All other extensions are lamp only for lines 1-8.
To customize line ringing, use one of the following:
3.
• User Programmable Features code
• Use
1.
The circuit types for keyset extensions are automatically set when the extension is plugged in.
Keyset users can place outside calls by:
• Pressing a line key and dialing the outside number. (See the
2.
• Pressing
• Line Dial-Up and Direct Line Access are disabled. (See the
All extensions have full incoming and outgoing access to all outside lines.
3.
• See
3101-01: Line Type to change this assignment.
2132-[01-64]: Line Ringing .
INTERCOM
Initial Startup Programming below to change this assignment.
#RAL
Default Features for Extensions
Default Features for Lines
. (See the User Programmable Features feature for more.)
Central Office Calls, Placing feature for more.)
, dialing 9, then dialing the outside number. (See the Line Group Routing feature for more.)
Central Office Calls, Placing feature for more.)
4.
By default, Feature Keys 1-12 are line keys. Keys 13-24 are undefined. See the Feature Keys feature for more.
Default Features for IntraMail
1.
Each extension has an IntraMail voice mailbox.
2.
All mailboxes are enabled. To disable a mailbox, see 2141-01: Station Mailbox Type .
3.
The IntraMail Automated Attendant does not answer outside calls. (See the Automated Attendant feature for more.)
Initial Startup Programming
1. Enter the programming mode.
1.
From any display telephone, press
The system passwords are:
2.
-
632379 (NECDSX)
for Installer (level 3),
Administrator 1 (level 1).
2. Assign the correct circuit type to each of your installed lines.
1.
In 3101-01: Line Type , assign the line circuit type (e.g., enter
2.
In 3103-03: DTMF Dialing , normally enter
3. By default, each extension has full incoming and outgoing access to each line. To change this assignment:
1.
In 2131-[01-64]: Line Access , change each extension’s line access as required. The options are:
-
0
for no access,
2.
Using 902x-Copy may save you time.
1
for incoming access only,
INTERCOM
1
(or press Feature Key 2) for DTMF dialing.
+ Dial
#*#*
+ Enter the system password +
9999
for System Administrator 2 (level 2),
1
or press Feature Key 2 for loop start).
2
for outgoing access only,
3
for full access
HOLD.
0000
for System
4.
By default, extensions 300-315 ring immediately day and night for lines 1-8. To change this assignment:
1.
In 2132-[01-64]: Line Ringing , set the ringing option for each extension, The options are:
-
0
for lamp only (no ringing) day and night,
ringing day and night
2.
Using 902x-Copy may save you time.
5. To change the default system passwords:
1.
Turn to the System Programming Password Protection feature to learn more about system passwords.
(1093067)
October 26, 2006, Rev 1
Printed in U.S.A.
1
for day and night ringing,
Empowered by Innovation
2
for night ringing only,
3
for delay
Loading...