Miele KFNS37692IDE1 Specifications

PerfectCool Bottom Mount Refrigerator

KFNS 37692 iDE-1

Specification Sheets TRS 05232017

8mieleusa.com

PerfectCool Bottom Mount Refrigerator
KFNS 37692 iDE-1

SPECIFICATIONS

KFNS 37692 iDE-1 — Item 38376922USA - Right Hinged (Convertible)

Overall Unit Width 22” (559 mm)

Overall Unit Height 69

Overall Unit Depth 21

Niche

Minimum Cabinet Opening Width

Minimum Cabinet Opening Height 69

Minimum Cabinet Opening Depth 21

Interior Volume

Fresh Food Volume

Freezer Volume 2.4 cu-ft (68 L)

Plumbing

Water Supply Requirements

KFNS 37692 iDE-1
Features:

• NEW: Miele PerfectCool Series

• FlexiLight - Shelf mounted LED

lighting

• Right hinged, convertible

• Soft Close Door

• DynaCool

• Dishwasher Safe door shelves

• Easy Sensor Controls

• Plumbed Ice Maker

• PerfectFresh Pro

• Bottle Fins

• Sabbath Mode

• Energy Star

Water Connection Line

Electrical

Electrical Requirements - Volts/Amps

Power Cord - Plug and length Yes - NEMA 5-15 plug, 6’ 6” (2 m)

Custom Panel Refer to manual for further detail

Maximum Panel Weight

Maximum Panel Thickness

Minimum Panel Thickness

Shipping

Shipping Weight 192.7 lbs (87.4 kg)

Shipping Dimensions 24

Support

Call Miele 800.843.7231

Miele Website

20/20 Link

11

/16” (1770 mm)

1

/2” (545 mm)

1

/16 ” (560 mm)

22

3

/4” (1772 mm)

5

/8” (550 mm)

6.3 cu-ft (178 L)

Connect to a cold water supply only. Must
be connected to a shut-off valve. The water
shut-off valve must be accessible after
installation. The water pressure must be
between 22 psi (1.5 bar) and may not exceed
87 psi (6 bar). If the pressure is higher than
87 psi (6 bar), a pressure reducing valve
must be installed.

Unit comes with a male 3/4” BPT connection
on back of unit. The connection parts
included with the appliance permit the
connection of various water lines (including
1/4” compression fitting). Water line is not
included.

110V / 120V, 60Hz, 15A (single)
110V / 120V, 60Hz, 20A (2 Individual units
installed side-by-side, using a Duplex outlet)

Top Panel - 44 lbs (20 kg)
Bottom Panel - 26 lbs (12 kg)

3

/4” (19 mm)

5

/8” (16 mm)

1

/2” W x 731/2” H x 225/8” D

8www.mieleusa.com

82020technologies.com

KFNS 37692 iDE-1

Specification Sheets TRS 05232017

Page 2 of 9

PerfectCool Bottom Mount Refrigerator
KFNS 37692 iDE-1

INSTALLATION DIMENSIONS

For additional information on Plumbing, please refer to the Plumbing section in the Install Manual.

For Side-by-Side installations two niche cutouts are required.

Specification Sheets TRS 05232017

KFNS 37692 iDE-1

Page 3 of 9

PerfectCool Bottom Mount Refrigerator
KFNS 37692 iDE-1

VENTILATION DIMENSIONS

- Air intake (1) occurs via the plinth at the bottom of
the appliance and the air escapes at the top (2) at the
rear of the housing unit.

- A ventilation gap of at least 1 5/8” (40 mm) depth
must be provided behind the appliance for air to
circulate.

- The ventilation cross-sections in the plinth
housing unit and above the appliance must amount
to at least 78 3/4”
without obstruction.

- Please refer to the manual for further ventilation
details.

2

to ensure that air can circulate

KFNS 37692 iDE-1

Page 4 of 9

Specification Sheets TRS 05232017

PerfectCool Bottom Mount Refrigerator
KFNS 37692 iDE-1

TOP VENTILATION CROSS-SECTION

(1) Directly above the appliance with a ventilation

grill (free airow of at least 78 3/4”2).

(2) In between the housing unit and ceiling.

(3) Through a suspended ceiling.

- Please refer to manual for further ventilation
details.

KFNS 37692 iDE-1

Specification Sheets TRS 05232017

Page 5 of 9

PerfectCool Bottom Mount Refrigerator
KFNS 37692 iDE-1

BOTTOM VENTILATION SLITS
DIMENSIONS

If you would like to use the ventilation slits:

- Cut an opening in the plinth (2) as shown in the gure.

- Place the ventilation grille (1) inot the opening.

- Push the snap connector (3) into the ventilation slits
from the rear until the hooks are touching the plinth

- Reinstall the plinth with the ventilation slits

KFNS 37692 iDE-1

Specification Sheets TRS 05232017

Page 6 of 9

PerfectCool Bottom Mount Refrigerator
KFNS 37692 iDE-1

CUSTOM PANEL

j - Top door panel
k - Bottom door panel
l - Unit's top door
m - Unit’s bottom door

KFNS 37692 iDE-1

Page 7 of 9

Specification Sheets TRS 05232017

PerfectCool Bottom Mount Refrigerator
KFNS 37692 iDE-1

CUSTOM PANEL CONTINUED

SPECIFICATIONS

Custom Panel Refer to manual for further detail

Maximum Panel Weight

Maximum Panel Thickness

Minimum Panel Thickness

Inset Panel

Minimum Vertical Gap - Between Cabinet
and Door Panel

Minimum Horizontal Gap - Between Top Cabinet
Panel and Door, Between
Door Panels

Top Panel - 44 lbs (20 kg)
Bottom Panel - 26 lbs (12 kg)

3

/4” (19 mm)

5

/8” (16 mm)

1

/8” (3 mm)

1

/8” (3 mm)

Framed Cabinet with Inset Door
Panel Calculation

Panel Width = Niche Opening Width - 1/4” (6 mm)

Panel Height = Niche Opening Height - 1/4” (6 mm)

Frameless Style Cabinet Panel
Calculation

Panel Width = Niche Opening Width + Left Side Panel Thickenss
+ Right Side Panel Thickness

Panel Height = Niche Opening Height + Top Panel Thickness
+ Bottom Panel Thickness

KFNS 37692 iDE-1

Specification Sheets TRS 05232017

Page 8 of 9

PerfectCool Bottom Mount Refrigerator
KFNS 37692 iDE-1

ADJUSTABLE DOOR HINGE

90o or 120o Opening

The door hinges are factory set so that the door can be
opned wide.

However if the opening angle of the door needs to be
limited for any reason, the hinge can be adjusted to
accommadate this.

Insert the limit pins provided into the hinges from above.
This will limit the opening angle of the applinace door to
90 o.

KFNS 37692 iDE-1

Specification Sheets TRS 05232017

Page 9 of 9