When using electrical appliances, basic safety precautions should always be
followed, including the following:
Read all instructions before installation or use of the coffee system.
Be certain your appliance is
Please read these instructions
carefully to prevent accidents and
machine damage.
This appliance is for household use
only. Use appliance only for its
intended use. Any other use could
be dangerous.
This appliance complies with current
safety requirements. Improper use of
the appliance can cause personal
injury and material damage.
properly installed and grounded by
a qualified technician. To guarantee the
electrical safety of this appliance,
continuity must exist between the
appliance and an effective grounding
system. It is imperative that this basic
safety requirement be met. If there is
any doubt, have the electrical system of
the house checked by a qualified
electrician. The manufacturer cannot be
held responsible for damages caused
by the lack or inadequacy of an
effective grounding system.
The manufacturer cannot be held
responsible for damage caused by
improper use of the appliance.
Electrical safety
Before connecting the appliance to
the electrical supply make sure
that the voltage and frequency details
listed on the data plate correspond with
the household electrical supply. If in
doubt, consult a qualified technician.
The appliance must be properly
installed before operation to ensure
that no electrical components are
accessible. Ensure that power is not
supplied to the appliance while
installation, repairs or maintenance
work is performed.
Do not use an extension cord to
connect the appliance to electricity.
Extension cords do not guarantee the
required safety of the appliance
(danger of overheating).
This appliance is not designed for
maritime use or for use in mobile
installations such as recreational
vehicles or aircraft. However, under
certain conditions it may be possible for
installation in these applications. Please
contact the Miele Technical Service
Department with specific requirements.
Before service or maintenance
work disconnect the power supply
by either removing the fuse, "tripping"
the circuit breaker or unplugging the
unit.
5
IMPORTANT SAFETY INSTRUCTIONS
Installation work and repairs should
only be performed by a trained
technician in accordance with national
and local safety regulations. Repairs
and other work by unauthorized
persons could be dangerous.
Never open the outer casing of the
appliance. Tampering with
electrical connections or components
and mechanical parts is dangerous and
may cause machine damage.
If the machine is installed in
combination with other appliances,
it should be installed with a protective
base between the appliance and the
unit.
To protect against fire, electric
shock and injury to persons do not
submerge the cord or plug in water or
any other liquid.
Do not let the cord hang over the
edge of the table or counter, or
touch hot surfaces.
Do not operate any appliance with
a damaged cord or plug, or after
the appliance malfunctions or has been
damaged in any manner. Return the
appliance to the nearest authorized
Miele dealer for examination, repair or
adjustment.
Always attach the plug to the
appliance first, then plug the cord
into the wall outlet. To disconnect, turn
the machine off by pressing the left jog
shuttle, then remove the plug from the
wall outlet.
Use
Only use Nespresso-coffee
capsules with this machine.
The coffee system must be cleaned
daily to prevent the growth of
harmful bacteria and mold. Please
read the "Coffee system care"
section of this booklet.
Caution! There is a risk of burns
when dispensing hot beverages,
they are extremely hot.
Do not touch hot surfaces. Use the
jog shuttles or steam lever.
Children should not use the
appliance unsupervised.
Danger of scalding!
This appliance must not be
installed or operated outdoors.
To avoid injuries allow the coffee
system to cool before cleaning or
putting on or taking off parts. Turn the
machine off at the main switch when
not in use and before cleaning.
Only fill the water tank with cold,
fresh tap water. Warm or hot water
or any other liquids may damage the
machine. The water should be changed
daily to prevent bacteria or mold
growth.
6
IMPORTANT SAFETY INSTRUCTIONS
The water lines must be rinsed and
the machine cleaned thoroughly
before the first coffee is prepared. See
"Daily coffee system care".
The use of accessories not
recommended by the appliance
manufacturer may result in fire, electric
shock or injury.
Do not reach into the perforator.
Injuries may occur.
Do not use damaged, broken or
dented capsules! They may jam in
the machine and damage it.
The hot water and steam
dispensed could cause scalding!
Use these functions carefully. The
machine must never be used to clean
objects.
Never use a steam cleaner to clean
the appliance. Pressurized steam
could damage electrical components
and cause a short circuit.
Only use the descaling tablets
provided by Miele and be sure to
use the correct mixture of water and
descaler. Otherwise appliance damage
may occur.
The capsule plate will soil more or
less depending on the coffee
capsule used. Clean the capsule plate
every 1 to 2 months with a cleaning
tablet, available from Miele.
Do not hang, lean, sit or place
heavy items on the door. The
machine may be damaged.
Do not place the coffee system on
or near a hot gas or electric burner,
or in a heated oven.
SAVE THESE
INSTRUCTIONS
The coffee system must be
descaled regularly with the
supplied descaling tablets. In areas
with very hard water the machine will
need to be descaled more often. The
manufacturer cannot be held
responsible for damages resulting from
insufficient descaling.
7
Guide to the machine
Front view
a Left display
b Left jog shuttle
Press this jog shuttle to turn the
machine on and off.
Turning it selects a desired
program, option or setting.
c Right jog shuttle
Press this jog shuttle:
– to start and stop the dispensing
of coffee or hot water.
– to select an option to alter or
customize a program.
– to save a setting into memory
when the machine is turned off.
Turning it selects a desired
program, option or a setting.
8
d Right display
e Upper door handle
(for installation at countertop height)
f Lower door handle
(for installation at a higher level,
e.g. upper cabinets)
g Plastic drip grill
h Metal drip catch
i Coffee dispenser
j Inset for Cappuccinatore
k Valve / Lever for steam and hot water
Interior view
Guide to the machine
l Main switch
m Capsule plate
(replaced with the descaling funnel
when descaling is performed)
n Perforator
(not visible, penetrates capsule to
assist in the brewing process)
o Capsule carousel
p Carousel tray
q Water tank
r Drip tray with grid
(grid avoids spilling during transport)
s Waste container
9
Displays
Left display
COSI
K1
2345 L on
Drink selection
–
Up to 5 different coffee types K, as
well as, steam L and hot water o
User profile
–
Up to 4 different users n
Important maintenance
–
Rinsing G, descaling k
Selection of Settings C
–
G
k C
Right display
LANGUAGE
F Y
–
–
–
Individual settings and information can
be selected in the right hand display.
FLanguage
mTime
KAllocation of coffee type
nUser name
IProgramming
ITotal number of cups of coffee
JMaintenance
ZReset to default settings
K n IIJZ
selects coffee or espresso
shows current actions, e.g. heating
prompts an action, e.g. close the
door
dispensed to date
10
The selected option will be
highlighted in the display.
First steps to use
Turning the machine on and off
The appliance must be correctly
installed and connected before the
first use.
Turning on
Press the left jog shuttle.
^
Míele
Welcome!
When turned on for the first time, a
welcome screen along with other
messages will appear in the right
display. The welcome screen will be
displayed each time the machine is
turned on until 5 drinks (including
steam) have been prepared.
COSI
K1
2345 L on
The displays light.
Turning off
^ Press the left jog shuttle until the
displays go dark.
G
k C
If the automatic rinsing function is
activated, both displays will go dark
when turned off. If coffee was
dispensed, the machine will be
rinsed and "Machine Rinsing" will
appear in the right display. When
finished the machine will shut off
completely.
11
First steps to use
Before using the coffee system
for the first time
1. Clean the parts
Hand wash the coffee capsule plate
^
with hot water and liquid dish soap.
The water tank can be washed in the
^
dishwasher.
2. Fill the water tank
Open the appliance door.
^
Lift the water tank and pull it out.
^
^ Fill the container with fresh, cold tap
water to the "Max." mark. Push the
water tank back into the machine.
3. Fill the system with water
HOT WATER
G
K12345 L
^ Set a cup under the steam valve.
o
n
k C
4. Rinse the lines
RINSE
K12345L on
Turn the left jog shuttle to "Rinse".
^
Press the right jog shuttle.
^
G
k C
Water runs from the coffee dispenser.
Press the steam lever down.
^
Water runs from the steam valve.
Push the steam lever up after a few
^
seconds.
^
Turn the left jog shuttle to "Hot water".
^
Press the right jog shuttle.
The steam valve dispenses hot water.
^
Press the right jog shuttle again to
turn the hot water off.
^
Turn the left jog shuttle to "Heating
with steam".
^
Press the steam lever down.
^
Push the steam lever up when steam
starts to be dispensed.
The lines are filled and the coffee
system is ready to use.
12
Filling water and coffee capsules
Filling the water tank
The water tank should be washed and
filled with fresh cold tap water before
each day of use.
Never put hot water or any other
liquid except cold water into the
water tank.
^ Open the appliance door.
^
Lift the water tank and pull it out.
^
Fill the container with fresh, cold tap
water to the "Max." mark.
A valve at the tank front prevents leaks.
^
Push the water tank back into the
machine.
13
Filling water and coffee capsules
Filling the coffee capsule
carousel
Only insert Nespresso coffee
capsules in the carousel.
Damaged, broken or dented
capsules should not be used they
may jam in the machine.
Pull the carousel tray, a, all the way
There are five chambers, each can hold
four capsules. The coffee types have to
be allocated to their respective
chambers to get the desired coffee
type. You can also fill each chamber
with the same coffee type.
The chambers are factory set for a
coffee type. Fill the chambers
respectively or program other coffee
types according to your preference.
See "Allocating various coffee types".
^
out.
Take the carousel, c, out.
^
Insert the capsules into the
^
chambers, d, with the flat, silver side
down.
Take care that the capsules sit
loosely in the chambers so they do
not jam.
^ Insert the carousel into the carousel
tray.
14
^ Push the carousel all the way into the
machine.
^
Close the door.
The machine aligns the carousel
automatically. A sound will be heard.
Changing the coffee capsules
^
Pull out the carousel tray and lift out
the carousel.
^
Push the carousel ring, b, up and
take out the capsules.
Allocating various coffee types
Twelve different Nespresso coffee types
are available for this coffee system.
They differentiate in terms of acidity,
fruitness, bitterness and roast.
Therefore the preparing times will vary.
See "The Espresso / Lungo range" for
more information on the coffee types.
Allocating the coffee types
Five different coffee types can be filled
in the five chambers of the capsule
carousel. The chambers can be either
allocated to the desired coffee types or
filled with the same coffee type in all
chambers.
SETTINGS F
K12345 L on
G
^ Turn the left jog shuttle to "Settings".
ALLOCATE TYPE
Y K
F
n IIJZ
k
C
Take the carousel from the machine
^
to see which coffee type is filled in
each chamber.
TYPE ARPEGGIO
K
1234
Turn the right jog shuttle to the
^
5
desired chamber and press to
confirm.
A
^
Turn the right jog shuttle to the
"Coffee bean" symbol. Press to
confirm.
TYPE COSI
K1
2345
A
The upper line shows the coffee type,
the lower line shows the chamber
number. If no type is allocated to the
chamber, the upper display line shows:
empty.
Some coffee types are factory set,
which you can either accept or change.
15
Allocating various coffee types
Allocating different coffee
types
CHAMBER 5
ARPEGGIO
Turn the right jog shuttle to the
^
~
desired coffee type and press to
confirm it to that chamber.
Setting a new coffee type
CHAMBER 5
save as
+
^ Turn the right jog shuttle to "save as"
if no coffee type is allocated yet, to
save a new coffee type or to name a
coffee type yourself.
^ Press the right jog shuttle.
CHAMBER 5 ............
A
B C D E F G H I J KL M~
~
To enter text
Turn the right jog shuttle to the first
^
letter or number and press to
confirm. The selected letter shows in
the upper line.
Repeat until the desired name is
^
entered.
To delete text
If you made a mistake, turn the right
^
jog shuttle until "delete" appears in
the display.
Pressing it deletes the last letter
^
entered.
^ Turn the right jog shuttle
counterclockwise to the alphabet and
continue entering the name.
Saving an entry
CHAMBER 5 TEST...
OK
+
~
The alphabet is displayed. Turn the
right jog shuttle to the right to display
the rest of the alphabet and the
numbers 0 through 9.
16
^
When the entry is complete, turn the
right jog shuttle until "OK" is
displayed.
^
Press to confirm.
The main menu is displayed, the last
selected chamber is highlighted.
^
To leave the menu turn the right jog
shuttle to the "back" symbol A and
press to confirm.
Not saving an entry
^
If you do not want to save an entry
turn the right jog shuttle until "back" is
displayed. Press and the entry will
not be saved.
Rinse the water lines before
preparing the first drink of the day. If
the "Automatic rinsing" option is set
to "on" and the machine is still cold
this will take place automatically. The
heating system will heat and the
water lines will be rinsed.
If the "Automatic rinsing" option is
set to "off", use the option "Rinse" in
the left display to rinse the lines.
See "Daily coffee system care".
Press the left jog shuttle to turn the
^
machine on.
COSI
K1
2345 L on
G
k C
The left display lights.
The right display shows briefly:
Making coffee
If the "Automatic rinsing" option is set to
"on" (default setting) the next message
shows:
Rinsing in progress - please wait
Water will run out of the coffee
dispenser and a sound will be heard as
the carousel aligns.
The right display shows:
ESPRESSO
q
rst
Please fill with
fresh water
This is a reminder to fill the water tank
with fresh water.
The next message shows:
Heating up Please wait
17
Making coffee
Prewarming the cups
Prewarming the cups allows the coffee
to fully develop the flavor and aroma.
Use caution. Steam and hot water
are very hot.
Place a cup under the steam / hot
^
water valve.
To prewarm with hot water
HOT WATER
G
K12345 L
Turn the left jog shuttle to the "Hot
^
o
n
water" option.
Press the right jog shuttle and half fill
^
the cup with hot water.
Press the right jog shuttle again to
^
stop the water from dispensing.
Leave the cup for a few seconds to
^
warm, then pour the water away.
To prewarm with steam
HEATING WITH STEAM
K12345
L
on
G
^ Turn the left jog shuttle to the
"Heating with steam" option.
k C
k C
18
^
Press the steam lever down.
The steam supply is temporary. If the
steam stops prematurely push the
steam lever up then down again.
^
Push the lever up to stop the steam
from dispensing.
^
Pour away any excess water.
Making coffee
Espresso and coffee
The flavor of the coffee depends on the
coffee capsule and the quantity of
water used. To ensure the machine
uses exactly the amount of water to suit
your taste and your cup size, there is a
choice of four serving sizes for
espresso / coffee.
Aside from the serving size, making
coffee and espresso are done the same
way.
Place a cup under the coffee
^
dispenser.
COSI
K1
2345 L on
^ Turn the left jog shuttle to the desired
coffee type.
ESPRESSO
q
rst
G
k C
Interrupting the brewing
Press the right jog shuttle to interrupt
^
the coffee dispensing immediately.
For coffee / espresso recipes see
the "Coffee glossary".
^
Turn the right jog shuttle to the
desired coffee or espresso size.
qEspresso
rCoffee
sDouble espresso
tDouble coffee
When selecting a double coffee or
espresso, two capsules will be
dispensed one after another. You can
set the water amount to your taste. See
"Setting the serving sizes".
^
Press the right jog shuttle to confirm
and the drink will be dispensed.
19
Making coffee
Cappuccinatore (milk froth mug)
A cappuccinatore (milk froth mug) is
supplied with the appliance.
Before using the cappuccinatore for
the first time, wash it either in the
dishwasher or with hot water and
liquid dish soap.
See "Common coffee system care".
The steam is regulated by turning the
valve:
1 Hot milk is prepared
2 Froth is prepared
The cappuccinatore has a valve, a,
over the handle and a spout on its side,
b.
Cold, whole milk is best for creating
froth. The higher the fat content, the
better the froth.
^ Turn the spout so that the black dot
points to the respective symbol.
Milk is frothed
1 into the cup
2 into the cappuccinatore
When milk is frothed in the
cappuccinatore the froth is hotter
and has more volume.
When frothing milk into a cup while
dispensing a coffee, the steam
system must be turned on. See
"Settings - Steam system".
20
Frothing milk into the cup
Prewarm the cup before filling with
^
froth.
Fill the cappuccinatore to the upper
^
"max" mark with cold milk.
Turn the spout to the cup symbol.
^
Turn the valve over the handle to the
^
froth symbol.
Place the cappuccinatore under the
^
steam valve.
Place a cup underneath the spout of
^
the cappuccinatore.
Making coffee
The steam supply is temporary. If the
steam stops and there is not enough
froth prepared, push the steam lever
up then down again.
^ Press the steam lever, a, down and
"connect" the valve with the
cappuccinatore, b.
Ensure that the valve engages
properly in the lower position.
Milk is frothed by the hot steam and
dispensed into the cup.
^
Turn the cappuccinatore valve to the
right. Once the froth flows steadily,
turn it to the left.
^
Push the steam lever up when
enough froth is prepared.
21
Loading...
+ 47 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.