PLASMA MONITOR
OWNER’S MANUAL
MODELS : MU-42PZ41V
MU-42PZ41VA
MU-42PZ41VB
MU-42PZ41VK
MU-42PZ41VR
MU-42PZ41VS
Please read this owner’s manual carefully before operating the Monitor.
Retain it for future reference.
Record model number and serial number of the Monitor. See the label attached on the back of the Monitor and quote this information to your dealer when you require service.
Model number :
Serial number :
P/NO : 3828VA0361C (RF02RA)
WARNING
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
FCC NOTICE
•A Class B digital device
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
•Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
WARNING
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
2
SAFETY INSTRUCTIONS
Important safeguards for you and your new product
Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference.
Observing the simple precautions discussed in this booklet can help you get many years of enjoyment and safe operation that are built into your new product.
This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.
1. Read Instructions
All the safety and operating instructions should be read before the product is operated.
2. Follow Instructions
All operating and use instructions should be followed.
3. Retain Instructions
The safety and operating instructions should be retained for future reference.
4. Heed Warnings
All warnings on the product and in the operating instructions should be adhered to.
5. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6. Water and Moisture
Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.
7. Accessories Carts and Stands
Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
8. Transporting Product
A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
case or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
11. Power Sources
This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
12. Power-Cord Polarization
This product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin. This plug will only fit into the grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
13. Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
14. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
Example of Grounding According to National Electrical Code Instructions
PORTABLE CART WARNING
9. Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a book-
Ground Clamp
|
|
|
|
Antenna Lead in Wire |
|
|
|
|
Antenna Discharge Unit |
|
|
|
|
(NEC Section 810-20) |
|
|
|
|
Grounding Conductor |
Electric Service |
|
|
|
(NEC Section 810-21) |
|
|
|
|
|
Equipment |
|
|
|
Ground Clamps |
|
|
|
|
|
|
|
|
|
Power Service Grounding |
|
|
|
|
Electrode System (NEC |
|
|
|
|
Art 250, Part H) |
NEC - National Electrical Code
(Continued on next page)
3
SAFETY INSTRUCTIONS
(Continued from previous page) |
|
|
15. Lightning |
21. Replacement Parts |
|
For added protection for this product (receiver) during a lightning |
When replacement parts are required, be sure the service tech- |
|
storm, or when it is left unattended and unused for long periods |
nician has used replacement parts specified by the manufactur- |
|
of time, unplug it from the wall outlet and disconnect the anten- |
er or have the same characteristics as the original part. |
|
na or cable system. This will prevent damage to the product due |
Unauthorized substitutions may result in fire, electric shock, or |
|
to lightning and power-line surges. |
other hazards. |
|
16. Power Lines |
22. Safety Check |
|
An outside antenna system should not be located in the vicinity |
Upon completion of any service or repairs to this product, ask |
|
of overhead power lines or other electric light or power circuits, |
the service technician to perform safety checks to determine that |
|
or where it can fall into such power lines or circuits. When |
the product is in proper operating condition. |
|
installing an outside antenna system, extreme care should be |
23. Wall or Ceiling Mounting |
|
taken to keep from touching such power lines or circuits as con- |
||
The product should be mounted to a wall or ceiling only as rec- |
||
tact with them might be fatal. |
||
ommended by the manufacturer. The product may slide or fall, |
||
17. Overloading |
||
causing serious injury to a child or adult, and serious damage to |
||
Do not overload wall outlets and extension cords as this can |
||
the product. |
||
result in a risk of fire or electric shock. |
||
|
||
18. Object and Liquid Entry |
24. Heat |
|
Never push objects of any kind into this product through open- |
The product should be situated away from heat sources such as |
|
ings as they may touch dangerous voltage points or short-out |
radiators, heat registers, stoves, or other products (including |
|
parts that could result in a fire or electric shock. Never spill liquid |
amplifiers) that produce heat. |
|
of any kind on the product. |
|
|
19. Servicing |
|
|
Do not attempt to service this product yourself as opening or |
|
|
removing covers may expose you to dangerous voltage or other |
|
|
hazards. Refer all servicing to qualified service personnel. |
|
|
20. Damage Requiring Service |
|
|
Unplug this product from the wall outlet and refer servicing to |
|
|
qualified service personnel under the following conditions: |
|
|
a. If the power-supply cord or plug is damaged. |
|
|
b. If liquid has been spilled, or objects have fallen into the prod- |
|
|
uct. |
|
|
c. If the product has been exposed to rain or water. |
|
|
d. If the product does not operate normally by following the |
|
|
operating instructions. Adjust only those controls that are |
|
|
covered by the operating instructions as an improper adjust- |
|
|
ment of other controls may result in damage and will often |
|
|
require extensive work by a qualified technician to restore |
|
|
the product to its normal operation. |
|
|
e. If the product has been dropped or the cabinet has been |
|
|
damaged. |
|
|
f. If the product exhibits a distinct change in performance. |
|
The PDP Manufacturing Process: Why colored dots may be present on the PDP screen
The PDP (Plasma Display Panel) which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell defects will normally occur in the PDP manufacturing process. Several colored dots visible on the screen should be acceptable. This also occurs in other PDP manufacturers' products and the dots appearing does not mean that this PDP is defective. Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology is designed to minimize cell defects.
Cooling Fan Noise
In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operating and cooling the PDP.
This noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during the operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not sufficient cause for the PDP to be exchanged or returned.
4
Contents
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4
Step 1. Monitor Installation & Setup
Controls and Connection Options . . . . . . . . . . . .6
External Equipment Connections . . . . . . . . . . . .7
External Equipment Viewing Setups . . . . . . .8~10
Remote Control Key Functions . . . . . . . . . . . . .11
Monitor Accessories . . . . . . . . . . . . . . . . . . . . .12
Monitor Installation/Mounting Options . . . . . . . .12
Step 2. Customize your Monitor’s Features
Basic Features Setup and Operation
Turning on the Monitor . . . . . . . . . . . . . . . . . . .14 Menu Language Selection . . . . . . . . . . . . . . . .14
Picture Menu Options
APC (Auto Picture Control) . . . . . . . . . . . . . . . .15 Manual Picture Control . . . . . . . . . . . . . . . . . . .15
Sound Menu Options
DASP (Digital Auto Sound Processing) . . . . . . .16 AVL (Auto Volume Leveler) . . . . . . . . . . . . . . . .16 Adjusting Sound (Manual Settings) . . . . . . . . . .16
Special Menu Options
Menu Rotation for Vertical Viewing . . . . . . . . . .17 Orbiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 White Wash . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Adjusting Auto Color Control . . . . . . . . . . . . . . .18 Manual Color Temperature Control . . . . . . . . . .18 Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Screen Menu Options
Auto Adjustment . . . . . . . . . . . . . . . . . . . . . . . .19 Adjusting Horizontal/Vertical Position . . . . . . . .19 Picture Phase Adjustments . . . . . . . . . . . . . . . .19 Initializing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Selecting Wide VGA mode . . . . . . . . . . . . . . . .20 Screen Adjustments . . . . . . . . . . . . . . . . . . . . .20 Screen Noise Reduction . . . . . . . . . . . . . . . . . .20 Setting Picture Format . . . . . . . . . . . . . . . . . . .21 Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Picture Size Adjustment . . . . . . . . . . . . . . . . . .21 Enlarged Picture Position Adjustment . . . . . . . .21
PIP (Picture In Picture) Feature
Watching PIP . . . . . . . . . . . . . . . . . . . . . . . . . .22 Selecting a Input Signal Source for PIP . . . . . . .22 Using Sub picture Still Function . . . . . . . . . . . .22 Moving the PIP . . . . . . . . . . . . . . . . . . . . . . . . .22 Selecting PIP Sound Options . . . . . . . . . . . . . .22
Twin Picture Setup Options
Watching Twin Picture . . . . . . . . . . . . . . . . . . . .23 Selecting a Input Signal Source for Twin Picture . .23 Selecting Twin Picture Sound Options . . . . . . . .23
Step.3 Miscellaneous
External Control Device Setup . . . . . . . . . . . . .24 IR Code (NEC format) . . . . . . . . . . . . . . . . . . .30 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Troubleshooting Checklist . . . . . . . . . . . . . . . . .34 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . .35
After reading this manual, keep it handy for future reference.
5
Monitor Controls
Front Panel Controls
ON/OFF |
INPUT |
MENU VOL. |
SELECT |
||
Main Power Button |
|
D,E Buttons |
Button |
|
|
|
VOLUME (F,G) Buttons |
|
|
|
|
|
MENU Button |
Power Standby Indicator
Illuminates red in standby mode,
Illuminates green when the
Monitor is turned on
Connection
Back Connection Panel
( ) R ( ) |
( |
) L ( |
) |
|
|
|
|
AUDIO L |
Y |
PB |
PR |
|
R AUDIO L (MONO) |
|
|
|
|
|
|
|
|
|
|
|
|
||||
EXTERNAL SPEAKER |
RS-232C INPUT |
RGB2 INPUT |
RGB1 INPUT |
|
|
INPUT |
COMPONENT |
S-VIDEO |
VIDEO INPUT |
AUDIO INPUT |
AC INPUT |
|||
(CONTROL/SERVICE) |
(DIGITAL RGB INPUT) |
(PC/DTV INPUT) |
|
|
(DVD/DTV INPUT) |
|||||||||
|
1 |
|
2 |
|
3 |
4 |
5 |
6 |
|
|
|
7 |
|
8 |
1.EXTERNAL SPEAKER (8 ohm output)
Connect to optional external speaker(s).
*For further information, refer to ‘Speaker & Speaker Stand’ manual.
2.RS-232C INPUT(CONTROL/SERVICE) PORT
Connect to the RS-232C port on a PC.
3.AUDIO INPUT/RGB1 INPUT (PC/DTV INPUT)/ RGB2 INPUT (DIGITAL RGB INPUT) JACKS
Connect the monitor output socket of the PC to this socket.
4.RGB1 OUTPUT (PC/DTV OUTPUT) JACKS
You can watch the RGB1 signal on another monitor, connect RGB1 OUTPUT (PC/DTV OUTPUT) to another monitor’s PC input port.
5.CONTROL LOCK Switch REMOTE CONTROL
When “CONTROL LOCK” is set “ON”, Monitor is operated by the external control device.
6.COMPONENT (DVD/DTV INPUT)/AUDIO INPUT JACKS
7.AUDIO/VIDEO INPUT JACKS
Connect audio/video out from external equipment to these jacks.
S-VIDEO INPUTS (S-VIDEO)
Connect video out from an S-VIDEO VCR to the S-VIDEO input.
8.POWER CORD SOCKET
This Monitor operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the Monitor on DC power.
6
External Equipment Connections
Monitor External Equipment Connection Panel
( ) R ( ) |
( ) L ( |
PR |
|
|
R AUDIO L (MONO) |
|
) |
|
|
|
|
||
EXTERNAL SPEAKER |
RS-232C |
S-VIDEO |
VIDEO INPUT |
AUDIO INPUT |
AC INPUT |
|
|
RS-232C |
RGB2 INPUT |
|
|
S-VIDEO |
AUDIO |
|
(DIGITAL |
RGB1 |
RGB |
INPUT |
INPUT |
||
INPUT |
||||||
RGB INPUT) |
INPUT |
AUDIO |
|
|
||
|
COMPONENT |
|
||||
|
|
(PC/DTV |
INPUT |
VIDEO INPUT |
||
|
|
INPUT) |
|
(DVD/DTV INPUT) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Connection to PC |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
Connection to AV equipment |
|
Note: All cables shown are not provided with the Monitor, except:
A D-sub 15 pin cable and DVI cable is supplied to connect the Monitor to a PC.
7
External Equipment Viewing Setups
Watching VCR Setup
match the colors of connecting ports (Video - yellow, Audio (L) - white,
the BNC-RCA adapter to the VIDEO INPUT on the Monitor. from the VCR to the AUDIO (L/MONO) input on the Monitor.
input, the picture quality is improved; compared to connecting a regular
for a long period of time. Typically a frozen still picture from a VCR. may remain visible on the screen.
adequate distance between the VCR and Monitor
control to select VIDEO. external input source.)
PLAY button on the VCR. (See VCR owner’s manual)
Watching Cable TV Setup
local provider and installing a converter, you can watch cable TV programunless a TV tuner device or cable TV converter box is connected to the
contact your local cable TV service provider(s).
control and select VIDEO. the cable box.
Setup
an external source, match the colors of AUDIO/VIDEO input jacks on the monitor with equipment: Video = yellow, Audio (Left) = white, Audio (Right) = red.
on the remote control to select VIDEO.
equipment. See external equipment operating guide.
Watching DVD Setup
Y, PB, PR of COMPONENT (DVD/DTV sockets of AUDIO INPUT.
jack, connect s-video of DVD to S-video inputs to Audio sockets of AUDIO
•Component Input ports
You can get better picture quality if you connect DVD player with component input ports as below.
Component ports of the
Y PB PR
Monitor
insert a DVD.
the remote control to select COMPO- manual for operating instructions.
Video output ports |
Y |
Pb |
Pr |
Y |
B-Y |
R-Y |
|
of DVD player |
Y |
Cb |
Cr |
|
Y |
PB |
PR |
8
Watching DTV Setup
purchase/connect a digital SET-TOP BOX.
Digital Set-Top Box
output to monitor COMPONENT (DVD/DTV INPUT) or to the monitor RGB1 (PC/DTV on your Set Top Box connectors.
outputs to monitor AUDIO INPUT jacks.
. (Refer to the owner’s ,manual for the digital SET-TOP BOX.) control to select COMPONENT or RGB 1.
PC Setup
picture and sound, connect a PC to the Monitor.
a fixed image on the monitor’s screen for a long period of time. The fixed image may become permanentthe screen; use a screen saver when possible.
the RGB1 INPUT(PC/DTV INPUT) or RGB2 INPUT(DIGITAL RGB INPUT) port of the Monitor; change the of PC accordingly.
input form; Separate
to Connect a PC to your Monitor
of PC is over UXGA, there will be no picture on the Monitor.
cable from the monitor output port of the PC to the RGB1 INPUT(PC/DTV INPUT) port of the Monitor from the DVI output port of the PC to the RGB2 INPUT(DIGITAL RGB INPUT) port on the Monitor. cable from the PC to the Audio input on the Monitor. (Audio cables are not included with the Monitor).
card, adjust PC sound as required.
a VESA Plug and Play Solution. The monitor provides EDID data to the PC system with a DDC protoautomatically to use this monitor.
is preset for RGB1 (Analog RGB), RGB2 (DVI, Digital RGB) mode. the monitor settings for Plug and Play functionally.
on the PC does not output analog and digital RGB simultaneously, connect only one of both RGB1 INPUT or RGB2 INPUT (DIGITAL RGB INPUT) to display the PC on the monitor.
on the PC does output analog and digital RGB simultaneously, set the monitor to either RGB1 or RGB2; is set to Plug and Play automatically by the monitor.)
640x480, 60Hz as DTV 480p based on the PC graphic card. In this case, change the screen scangraphic card.
not work depending on video card if using a DVI-I cable.
picture, match the VGA mode and DVI signal (852x480, 848x480). (See page 20)
and apply power to the Monitor.
by pressing the POWER button on the Monitor’s remote control.
SELECT button on the remote control to select the RGB1 or RGB2 input source. output of the PC to SXGA or under (1280 x 1024, 75Hz).
9
Monitor Display Specifications
|
|
Vertical |
DDC |
Resolution |
Horizontal |
Vertical |
DDC |
|
|
Frequency(Hz) |
Frequency(KHz) |
Frequency(Hz) |
|||
|
|
|
|
|
|||
|
|
70.09 |
|
832x624 |
49.725 |
74.55 |
o |
|
|
85.08 |
|
848x480 |
31.469 |
59.94 |
|
|
|
|
|
or |
|
|
|
|
|
70.08 |
o |
35.000 |
70.06 |
|
|
|
|
85.03 |
o |
852x480 |
37.500 |
75.00 |
|
|
|
|
|
|
|
|
|
|
|
59.94 |
o |
|
48.363 |
60.00 |
o |
|
|
66.66 |
o |
1024x768 |
56.476 |
70.06 |
o |
|
|
72.80 |
o |
60.023 |
75.02 |
o |
|
|
|
|
|||||
|
|
75.00 |
o |
|
68.677 |
84.99 |
|
|
|
|
|
|
|
|
|
|
|
85.00 |
|
|
54.348 |
60.05 |
o |
|
|
90.03 |
|
1152x864 |
63.995 |
70.01 |
o |
|
|
100.04 |
|
67.500 |
75.00 |
o |
|
|
|
|
|
||||
|
|
120.00 |
|
|
77.487 |
85.05 |
|
|
|
|
|
|
|
|
|
|
|
56.25 |
o |
1152x870 |
68.681 |
75.06 |
o |
|
|
|
|
|
|
|
|
|
|
60.31 |
o |
1280x960 |
60.000 |
60.000 |
o |
|
|
72.18 |
o |
75.000 |
75.00 |
o |
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
75.00 |
o |
1280x1024 |
63.981 |
60.02 |
o |
|
|
85.06 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
90.00 |
|
|
|
|
|
|
|
100.00 |
|
|
|
|
|
|
|
|
|
|
|
|
|
Resolution |
Horizontal |
Vertical |
DDC |
Resolution |
Horizontal |
Vertical |
DDC |
|
Frequency(KHz) |
Frequency(Hz) |
Frequency(KHz) |
Frequency(Hz) |
|||||
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
640x350 |
31.468 |
70.09 |
|
832x624 |
49.725 |
74.55 |
o |
|
|
|
|
|
|
|
|
||
37.861 |
85.08 |
|
848x480 |
31.469 |
59.94 |
|
||
|
|
|
||||||
|
|
|
|
or |
|
|
|
|
640x400 |
31.469 |
70.08 |
o |
35.000 |
70.06 |
|
||
37.927 |
85.03 |
o |
852x480 |
37.500 |
75.00 |
|
||
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
31.469 |
59.94 |
o |
|
48.363 |
60.00 |
o |
|
|
35.000 |
66.66 |
|
1024x768 |
56.476 |
70.06 |
|
|
|
37.861 |
72.80 |
|
60.023 |
75.02 |
|
||
|
|
|
|
|||||
640x480 |
37.500 |
75.00 |
|
|
68.677 |
84.99 |
|
|
|
|
|
|
|
|
|
||
43.269 |
85.00 |
|
|
54.348 |
60.05 |
o |
||
|
|
|
||||||
|
45.913 |
90.03 |
|
1152x864 |
63.995 |
70.01 |
|
|
|
53.011 |
100.04 |
|
67.500 |
75.00 |
|
||
|
|
|
|
|||||
|
64.062 |
120.00 |
|
|
77.487 |
85.05 |
|
|
|
|
|
|
|
|
|
|
|
|
35.156 |
56.25 |
|
1152x870 |
68.681 |
75.06 |
o |
|
|
|
|
|
|
|
|
|
|
|
37.879 |
60.31 |
o |
1280x960 |
60.000 |
60.000 |
o |
|
|
48.077 |
72.18 |
|
75.000 |
75.00 |
|
||
|
|
|
|
|||||
800x600 |
|
|
|
|
|
|
|
|
46.875 |
75.00 |
|
1280x1024 |
63.981 |
60.02 |
o |
||
|
53.674 |
85.06 |
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
56.000 |
90.00 |
|
|
|
|
|
|
|
64.016 |
100.00 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
10
Remote Control Key Functions
-When using the remote control aim it at the remote control sensor of the Monitor.
-There's maybe a defect in consecutive operation of remote control in specified brightness according to this monitor feature.
POWER
Switches the Monitor on from standby or off to standby.
SLEEP
Sets the sleep timer. (Refer to p.17)
APC
Adjusts the factory preset picture according to the room.
(Refer to p.15)
ARC
Changes the picture format. (Refer to p.21)
ZOOM-
Reduces the main picture size. (Refer to p. 21)
SPLIT ZOOM
Enlarge the screen with regular ration. (Refer to p. 22)
MENU
Displays on screen menus one by one. Exits the current menu.
Memorizes menu changes.
PIP
Switches the sub picture on and off. (Refer to p. 22)
TWIN PICTURE
(Refer to p. 23)
PIP INPUT
Selects the input mode for the sub picture. (Refer to p. 22, 23)
SOUND SELECT
Select main picture sound or sub picture sound for
PIP.(Refer to p. 22, 23)
PIP POSITION
Change the sub picture position. (Refer to p. 22)
PIP STILL
Freeze sub picture motion. (Refer to p. 22)
Installing Batteries
|
|
|
|
|
|
INPUT SELECT |
|
|
|
|
|
|
Selects: VIDEO, S-VIDEO, RGB1/2 |
|
|
|
|
|
|
or COMPONENT mode. |
|
|
|
|
|
|
DASP |
|
POWER |
|
|
|
|
To select the sound appropriate to |
|
|
|
|
|
your viewing program character: |
|
|
|
|
|
|
|
|
|
SLEEP |
|
|
INPUT SELECT |
FLAT, SPORTS, CINEMA, MUSIC, |
|
|
|
|
or USER (Refer to p.16) |
|||
|
|
|
|
|
|
|
|
APC |
|
|
DASP |
AUTO CONFIG |
|
|
|
|
|
|
|
|
|
ARC |
|
|
AUTO CONFIG. |
||
|
|
|
(Refer to p.19) |
|||
|
|
|
|
|
|
ZOOM - |
|
ZOOM + |
ZOOM+ |
|
|
|
|
SPLIT ZOOM |
|
KEY LOCK |
Enlarges the main picture size. |
|
(Refer to p. 21) |
||
|
|
|
|
MENU |
|
MUTE |
KEY LOCK |
|
|
|
|
|
|
|
To control the monitor with remote |
|
|
|
control only. (Refer to p. 18) |
VOL |
OK |
VOL |
MUTE |
|
|||
|
|
|
|
|
|
|
Switches the sound on or off. |
|
|
|
OK |
|
|
|
|
D / E |
|
1 |
2 |
3 |
Selects a menu option. |
|
|
||||
4 |
5 |
6 |
F / G (Volume button) |
|
Increases/decreases sound level. |
||||
|
|
|
||
7 |
8 |
9 |
Adjusts menu settings. |
|
|
0 |
|
|
|
|
|
|
NUMBER buttons |
|
POWER |
STOP |
P/STILL |
|
|
REW |
PLAY |
FF |
VCR BUTTONS |
|
|
|
REC |
Controls a LG video cassette recorder. |
|
|
|
|
||
PIP |
TWIN PICTURE PIP INPUT |
|
||
SOUND SELECT PIP POSITION |
PIP STILL |
|
•Open the battery compartment cover on the back side and insert the batteries with correct polarity.
•Install two 1.5V alkaline batteries of AAA type. Don’t mix used batteries with new batteries.
11