CP-1 Plus (Version 2.0) Quick Reference Guide
The Front Panel
exicon DIGITAL AUDIO ENVIRONMENT PROCESSOR |
|
|
Plus |
|||
|
|
CP-1 CP-1 |
||||
I |
II |
SOURCE TAPE PRE |
POST |
SYSTEM |
EFFECT |
POWER |
|
|
|
|
MUTE |
MUTE |
|
|
|
|
|
INPUT LEVEL |
|
|
|
SOURCE |
MONITOR |
TAPE |
|
|
|
The Version 2.0 Remote Control
PANORAMA provides greater
spaciousness and envelopment for either music or films. These programs
can utilize left and right rear channels but are also effective using only two front loudspeakers.
The CONCERT HALL modes contain two effects: Ambience (Club and Hall) and Reverb (Cathedral).
The Ambience effect generates the appropriate early reflections for stereo simulation of rectangular and
fan-shaped halls in a variety of sizes. The Reverb effect emphasizes rich, smooth reverberant decay in small, medium or large spaces.
The Surround modes are designed to make full use of additional loudspeakers at the center, sides and rear
of the room. In MUSIC SURROUND, FULL allows unprocessed music to be played over all your speakers. MUSIC LOGIC is appropriate for any type of music and for stereo films which are not Dolby encoded. STEREO LOGIC envelopes you as though you were on stage with the musicians. The MOVIE SURROUND modes work with film sound tracks to recreate the theater experience. MONO LOGIC expands the music and effects on monaural films. TV MATRIX provides surround effects for TV viewing of monaural, stereo and stereo-synthesized programs. PRO LOGIC should be used during playback of any encoded films or music.
PANORAMA |
BANK |
||
1 |
2 |
3 |
|
NORMAL |
WIDE |
BINAURAL |
|
CONCERT HALLS |
PARAM |
||
4 |
5 |
6 |
|
CLUB |
HALL |
CATHEDRAL |
|
MUSIC SURROUND |
|
||
7 |
8 |
9 |
|
FULL |
MUSIC |
STEREO |
|
MOVIE SURROUND |
|
||
10 |
11 |
12 |
|
MONO TV MATRIX |
|
|
|
|
F |
R |
|
EFFECT |
BALANCE |
VOLUME |
|
|
B |
L |
|
DOLBY SURROUND
SYSTEM EFFECT
MUTE
PRO - LOGIC
BANK switches between 12 factory Presets and 12 User registers where customized modes may be stored.
PARAM selects the various adjustable parameters of the current mode.
PARAM: UP and DOWN adjust the current parameter.
EFFECT: UP and DOWN adjust the level or intensity of effects added by the CP-1.
BALANCE: F and B adjust the levels between the front and the rear of the listener.
BALANCE: L and R adjust the left/right balance of all speakers: front, sides and rear.
VOLUME: UP and DOWN adjust the level of all channels simultaneously.
SYSTEM MUTE turns off all outputs and lights both SYSTEM and EFFECT MUTE
LEDs.
EFFECTS MUTE turns off any effects added by the CP-1. (Pushing EFFECT MUTE while in systemmute mode turns the effects alone back on.)
Note
To store a modified Preset program, press PARAM until the display reads: MEMORIZE PROGRAM, then press any of the 12 program keys to store all current settings in the corresponding User register. User registers automatically store changes as they are entered.
The CP-1’s User Bank can be cleared and reloaded with duplicates of the factory Preset programs at any time. Turn on the CP-1 while holding down PARAM. Continue to hold down PARAM for several seconds. This puts the unit into TEST mode. Push EFFECT MUTE to clear and reload the User Bank and to restore all initial settings of Volume, Balance, Contrast, Configuration, etc. Push PARAM again to begin normal operation.
Lexicon CP-1 Plus (Version 2.0) Digital Audio Environment Processor
Manufactured under license from Dolby Laboratories Licensing Corporation. Additionally licensed under one or more of the following patents: U.S. numbers 3,632,886, 3,746,792 and 3,959,590; Canadian numbers 1,004,603 and 1,037,877. "Dolby" and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
Lexicon CP-1 Plus (Version 2.0) Quick Reference Guide
The Rear Panel
|
LEVEL |
|
|
REAR SIDE |
MAIN |
TAPE |
INPUTS |
|
|
OUT |
|
L
OUTPUTS
R
Push Phantom/In if you have no center channel; leave it out if a center speaker is connected.
Leaving this button out with no center channel will cause the Surround programs to malfunction.
Configuration |
|
|
Center Phantom |
|
Center Phantom |
Button IN |
|
Button IN |
1 |
2 |
3 |
Center Phantom |
Center Phantom |
|
Button IN |
Button IN |
|
4 |
5 |
6 |
|
|
Center Phantom |
|
|
Button IN |
7 |
8 |
9 |
|
|
Center Phantom |
|
|
Button IN |
10 |
11 |
12 |
Choose the diagram that most closely corresponds to your room and note its number.
Press BANK and hold for five seconds. The display will read: LCD CONTRAST ADJ. The CP- 1 is now in Configuration mode.
• Use PARAM UP or DOWN to adjust display contrast.
Push PARAM to select the Speaker Configuration menu.
• Push PARAM UP or DOWN until the configuration you have chosen and the description in the display match.
speaker connected to center output
speakers connected to Main outputs
speakers connected to Side outputs
speakers connected to Rear outputs
The actual angle, or "toe in" of the speakers should be set according to the manufacturer's suggestions.
If you are using only one rear speaker, or a single amplifier channel for the rears, it may be hooked up to either the left or right rear output, as long as you use the correct Configuration number.
Subwoofers are not shown in any of these configurations. Consult the subwoofer owner's manual or your dealer for proper placement of subwoofers.
3 Oak Park
Bedford, MA 01730 USA
Lexicon Part # 070-09112 |
© 1992 Lexicon, Inc. |