Lenovo L380 Maintenance Manual

Name: Lenovo L380
Brand: Lenovo
SKU: 2788745
Rating: 5 (3 reviews)

5 (3)

L380, L380 Yoga, S2 3rd Gen, and S2 Yoga 3rd Gen Hardware Maintenance Manual

Note: Before using this information and the product it supports, be sure to read the general information under Appendix A “Notices” on page 115.

First Edition (January 2018)

LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.

Contents

About this manual . . . . . . . . . . . . iii

Chapter 1. Safety information. . . . . . 1

General safety . . . . . . . . . . . . . . . . 1 Electrical safety . . . . . . . . . . . . . . . . 2 Safety inspection guide. . . . . . . . . . . . . 3 Handling devices that are sensitive to electrostatic

discharge . . . . . . . . . . . . . . . . . . 3 Grounding requirements . . . . . . . . . . . . 4 Safety notices (multilingual translations) . . . . . . 4 Laser compliance statement (multilingual

translations) . . . . . . . . . . . . . . . . 19

Chapter 2. Important service information . . . . . . . . . . . . . . . 25

Strategy for replacing FRUs . . . . . . . . . . 25

Strategy for replacing a hard disk drive or a solid-state drive . . . . . . . . . . . . . 25

Important notice for replacing a system board . . . . . . . . . . . . . . . . . 26

How to use error codes . . . . . . . . . . 26

Strategy for replacing FRUs for CTO, special-bid, and standard models. . . . . . . . . . . . . 26

Product definition . . . . . . . . . . . . 26

FRU identification. . . . . . . . . . . . 27

Chapter 3. General checkout . . . . . 29

What to do first . . . . . . . . . . . . . . . 29 Checkout guide . . . . . . . . . . . . . . . 30

Lenovo Solution Center . . . . . . . . . . 30 Quick test programs . . . . . . . . . . . 30 UEFI diagnostic program . . . . . . . . . 31 Bootable diagnostic programs . . . . . . . 32

Power system checkout . . . . . . . . . . . 33

Checking the ac power adapter . . . . . . . 33 Checking operational charging . . . . . . . 33 Checking the battery pack . . . . . . . . . 33 Checking the coin-cell battery . . . . . . . 34

Chapter 4. Related service information . . . . . . . . . . . . . . . 37

Recovery overview for the Windows 10 operating system . . . . . . . . . . . . . . . . . . 37

Resetting your computer . . . . . . . . . 37 Using advanced startup options . . . . . . 37 Recovering your operating system if Windows

10 fails to start . . . . . . . . . . . . . 38 Creating and using a recovery USB drive . . . 38

Passwords. . . . . . . . . . . . . . . . . 38

Power-on password . . . . . . . . . . . 39 Hard disk password . . . . . . . . . . . 39 Supervisor password . . . . . . . . . . . 39 How to remove the power-on password . . . 39 How to remove the hard disk password. . . . 40

Power management . . . . . . . . . . . . . 40

Sleep mode . . . . . . . . . . . . . . 40 Hibernation mode . . . . . . . . . . . . 41

Symptom-to-FRU index . . . . . . . . . . . 41

Numeric error codes . . . . . . . . . . . 42 Error messages . . . . . . . . . . . . . 44 Beep errors. . . . . . . . . . . . . . . 44 No-beep symptoms . . . . . . . . . . . 45 LCD-related symptoms . . . . . . . . . . 46 Intermittent problems. . . . . . . . . . . 46 Undetermined problems . . . . . . . . . 46

Chapter 5. Status indicators . . . . . 49

Chapter 6. Special keys . . . . . . . . 51

Chapter 7. Locations . . . . . . . . . 53

Locating computer controls, connectors, and indicators . . . . . . . . . . . . . . . . . 53

Front view . . . . . . . . . . . . . . . 53 Left-side view. . . . . . . . . . . . . . 54 Right-side view . . . . . . . . . . . . . 54 Bottom view . . . . . . . . . . . . . . 55 Rear view . . . . . . . . . . . . . . . 55

Locating FRUs and CRUs . . . . . . . . . . . 55

Major FRUs and CRUs . . . . . . . . . . 57 LCD FRUs and CRUs . . . . . . . . . . . 59 Miscellaneous parts . . . . . . . . . . . 62 Connector and cable guide . . . . . . . . 62

Looking up FRU information . . . . . . . . . . 68

Chapter 8. FRU replacement notices . . . . . . . . . . . . . . . . . 69

Screw notices . . . . . . . . . . . . . . . 69 Retaining serial numbers . . . . . . . . . . . 70

Restoring the serial number of the system unit . . . . . . . . . . . . . . . . . . 70

Retaining the UUID. . . . . . . . . . . . 71

Chapter 9. Removing or replacing a FRU. . . . . . . . . . . . . . . . . . . 73

General guidelines. . . . . . . . . . . . . . 73 Disabling the built-in battery . . . . . . . . . . 74

1010 MicroSD card . . . . . . . . . . . . . 74 1020 Keyboard . . . . . . . . . . . . . . . 75 1030 Base cover assembly . . . . . . . . . . 78 1040 Memory module . . . . . . . . . . . . 79 1050 M.2 solid-state drive. . . . . . . . . . . 80 1060 Coin-cell battery . . . . . . . . . . . . 81 1070 Wireless LAN card . . . . . . . . . . . 81 1080 ThinkPad Pen Pro. . . . . . . . . . . . 82 1090 Battery pack . . . . . . . . . . . . . . 83 1100 Speaker assembly . . . . . . . . . . . 84 1110 Trackpad and trackpad cable . . . . . . . 85 1120 Wireless LAN antenna assembly . . . . . . 86 1130 ThinkPad Pen Pro charger with cable . . . . 87 1140 Power button board with cable . . . . . . 88 1150 NFC board with cable, NFC attenna . . . . 90 1160 Fingerprint reader board bracket and

fingerprint reader board with cable . . . . . . . 90 1170 Rear camera board with cable . . . . . . . 91 1180 LCD unit . . . . . . . . . . . . . . . 92 1190 HDMI connector bracket . . . . . . . . . 94 1200 USB 3.1 connector bracket . . . . . . . . 94 1210 Thermal fan . . . . . . . . . . . . . . 95 1220 System board . . . . . . . . . . . . . 96 1230 Keyboard bezel assembly . . . . . . . . 99

LCD FRUs for Yoga models . . . . . . . . . . 100

2010 Strip cover and rubber caps . . . . . . 100 2020 Touch module assembly and hinge

rubber. . . . . . . . . . . . . . . . . 101 2030 LCD hinges . . . . . . . . . . . . 103 2040 LCD cable and touch control board . . . 103 2050 Infrared camera/microphone module

with cable . . . . . . . . . . . . . . . 104 2060 Sensor board with cable and LCD rear

cover assembly . . . . . . . . . . . . . 106 2070 ThinkPad-logo-LED card with cable . . . 109

LCD FRUs for non-yoga models . . . . . . . . 109

2080 LCD bezel . . . . . . . . . . . . . 109 2090 LCD panel and LCD cable . . . . . . 110 2100 LCD hinges . . . . . . . . . . . . 111 2110 RGB camera/microphone module with

cable and LCD rear cover assembly . . . . . 112

Appendix A. Notices. . . . . . . . . . 115

Electronic emission notices . . . . . . . . . . 116 Trademarks . . . . . . . . . . . . . . . . 116

Appendix B. Abbreviation and acronym table . . . . . . . . . . . . . 117

ii L380, L380 Yoga, S2 3rd Gen, and S2 Yoga 3rd Gen Hardware Maintenance Manual

About this manual

This manual contains service and reference information for the following ThinkPad® product:

ThinkPad L380 Yoga

ThinkPad L380

ThinkPad S2 Yoga 3rd Gen Machine type (MT) 20L2

ThinkPad S2 3rd Gen Machine type (MT) 20L1

Machine type (MT) 20M7, 20M8

Machine type (MT) 20M5, 20M6

Use this manual along with the advanced diagnostic tests to troubleshoot problems.

Important:

This manual is intended only for trained service technicians who are familiar with ThinkPad products. Use this manual along with the advanced diagnostic tests to troubleshoot problems effectively. Before servicing a ThinkPad product, be sure to read all the information under Chapter 1 “Safety information” on page 1 and Chapter 2 “Important service information” on page 25.

iv L380, L380 Yoga, S2 3rd Gen, and S2 Yoga 3rd Gen Hardware Maintenance Manual

Chapter 1. Safety information

This chapter presents the following safety information that you need to be familiar with before you service a ThinkPad notebook computer.

• “General safety” on page 1

• “Electrical safety” on page 2

• “Safety inspection guide” on page 3

• “Handling devices that are sensitive to electrostatic discharge” on page 3

• “Grounding requirements” on page 4

• “Safety notices (multilingual translations)” on page 4

• “Laser compliance statement (multilingual translations)” on page 19

General safety

Follow these rules to ensure general safety:

• Observe good housekeeping in the area of the machines during and after maintenance.

• When lifting any heavy object:

1. Ensure that you can stand safely without slipping.

2. Distribute the weight of the object equally between your feet.

3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.

4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you think is too heavy for you.

• Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.

• Before you start the machine, ensure that other service technicians and the customer's personnel are not in a hazardous position.

• Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the machine.

• Keep your toolcase away from walk areas so that other people will not trip over it.

• Do not wear loose clothing that can be trapped in the moving parts of a machine. Ensure that your sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.

• Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, about 8 centimeters (3 inches) from the end.

• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing, because metal objects are good electrical conductors.

• Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using solvents, or working in any other conditions that might be hazardous to your eyes.

• After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that is worn or defective.

• Reinstall all covers correctly before returning the machine to the customer.

• Fan louvers on the machine help to prevent overheating of internal components. Do not obstruct fan louvers or cover them with labels or stickers.

Electrical safety

Observe the following rules when working on electrical equipment.

Important:

• Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents.

• Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges (ESD). Do not use this type of mat to protect yourself from electrical shock.

• Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly.

• Do not work alone under hazardous conditions or near equipment that has hazardous voltages.

• Disconnect all power before: – Performing a mechanical inspection – Working near power supplies – Removing or installing main units

• Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer to power off the wall box that supplies power to the machine, and to lock the wall box in the off position.

• If you need to work on a machine that has exposed electrical circuits, observe the following precautions: – Ensure that another person, familiar with the power-off controls, is near you. That person must be there

to switch off the power, if necessary.

– Use only one hand when working with powered-on electrical equipment; keep the other hand in your

pocket or behind your back.

CAUTION: An electrical shock can occur only when there is a complete circuit. By observing the above rule, you may prevent a current from passing through your body.

– When using testers, set the controls correctly and use the approved probe leads and accessories for

that tester.

– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as

metal floor strips and machine frames.

Observe the special safety precautions when you work with very high voltages. Instructions for these precautions are in the safety sections of maintenance information. Use extreme care when measuring high voltages.

• Regularly inspect and maintain your electrical hand tools for safe operational condition.

• Do not use worn or broken tools and testers.

• Never assume that power has been disconnected from a circuit. First, check that it has been powered off.

• Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds.

• Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage.

• Do not service the following parts with the power on: – Power supply units – Pumps – Blowers and fans – Motor generators – Units similar to those listed above

This practice ensures correct grounding of the units.

L380, L380 Yoga, S2 3rd Gen, and S2 Yoga 3rd Gen Hardware Maintenance Manual

• If an electrical accident occurs: – Use caution; do not become a victim yourself. – Switch off power. – Send another person to get medical aid.

Safety inspection guide

The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service technicians from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-ThinkPad features or options not covered by this inspection guide.

If any unsafe conditions are present, you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem.

Consider these conditions and the safety hazards they present:

• Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal electrical shock)

• Explosive hazards, such as a damaged CRT face or a bulging capacitor

• Mechanical hazards, such as loose or missing hardware

To determine whether there are any potentially unsafe conditions, use the following checklist at the beginning of every service task. Begin the checks with the power off, and the power cord disconnected.

Checklist:

1. Check exterior covers for damage (loose, broken, or sharp edges).

2. Turn off the computer. Disconnect the power cord.

3. Check the power cord for:

a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground

continuity for 0.1 ohm or less between the external ground pin and the frame ground.

b. The power cord should be the authorized type specified for your computer. Go to:

www.lenovo.com/serviceparts-lookup

c. Insulation must not be frayed or worn.

4. Check for cracked or bulging batteries.

5. Remove the cover.

6. Check for any obvious non-ThinkPad alterations. Use good judgment as to the safety of any nonThinkPad alterations.

7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage.

8. Check for worn, frayed, or pinched cables.

9. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with.

http://

Handling devices that are sensitive to electrostatic discharge

Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects.

Chapter 1. Safety information 3

Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge.

Notes:

1. Use product-specific ESD procedures when they exceed the requirements noted here.

2. Ensure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.

When handling ESD-sensitive parts:

• Keep the parts in protective packages until they are inserted into the product.

• Avoid contact with other people.

• Wear a grounded wrist strap against your skin to eliminate static on your body.

• Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap.

• Use a grounded work mat to provide a static-free work surface. The mat is especially useful when handling ESD-sensitive devices.

• Select a grounding system, such as those listed below, to provide protection that meets the specific service requirement.

Note: The use of a grounding system to guard against ESD damage is desirable but not necessary.

– Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.

– When working on a double-insulated or battery-operated system, use an ESD common ground or

reference point. You can use coax or connector-outside shells on these systems.

– Use the round ground prong of the ac plug on ac-operated computers.

Grounding requirements

Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician.