Leica DISTO D3a-BT User Manual

User Manual
English
Congratulations on the purchase of your Leica DISTO™ D3a BT .
Carefully read the Safety Instruc­tions and the User Manual before using this product.
The person responsible for the instrument must ensure that all users understand these directions and adhere to them.
Contents
Safety Instructions ............................................. 1
Start-up................................................................6
Menu functions...................................................9
Operation........................................................... 11
Measuring .......................................................... 12
Functions ...........................................................13
Working with BLUETOOTH® ............................ 19
Appendix............................................................ 20
Safety Instructions
Symbols used
The symbols used in the Safety Instructions have the following meanings:
WARNING:
Indicates a potentially hazardous situation or an unintended use which, if not avoided, will result in death or serious injury.
CAUTION:
Indicates a potentially hazardous situation or an unintended use which, if not avoided, may result in minor injury and/or in appreciable material, finan­cial and environmental damage.
Important paragraphs which must be adhered
)
to in practice as they enabled the product to be used in a technically correct and efficient manner.
Use of the instrument
Permitted use
Measuring distances
Computing functions, e. g. areas and volumes
Storing measurements (BLUETOOTH®)
•Measuring tilts
D
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
Leica DISTO™ D3a BT 776750 gb
1
Safety Instructions
D
Prohibited use
Using the instrument without instruction
GB
Using outside the stated limits
Deactivation of safety systems and removal of
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
explanatory and hazard labels
Opening of the equipment by using tools (screw­drivers, etc.), as far as not specifically permitted for certain cases
Carrying out modification or conversion of the product
Use after misappropriation
Use of accessories from other manufacturers without the express approval of Leica Geosys­tems.
Deliberate or irresponsible behaviour on scaf­folding, when using ladders, when measuring near machines which are running, or near parts of machines or installations which are unprotected
Aiming directly into the sun
Deliberate dazzling of third parties; also in the dark
Inadequate safeguards at the surveying site (e.g. when measuring on roads, construction sites, etc.)
Limits of use
)
The Leica DISTO™ is designed for use in areas perma­nently habitable by humans, do not use the product in explosion hazardous areas or in aggressive envi­ronments.
Safety Instructions
See section “Technical Data“.
Areas of responsibility
Responsibilities of the manufacturer of the orig­inal equipment Leica Geosystems AG, CH-9435 Heerbrugg (for short Leica Geosystems):
Leica Geosystems is responsible for supplying the product, including the User Manual and original accessories, in a completely safe condition. (addi­tional language versions can be found at:
www.disto.com.
Responsibilities of the manufacturer of non-Leica accessories:
The manufacturers of non-Leica accessories
)
for the Leica DISTO™ are responsible for developing, implementing and communicating safety concepts for their products. They are also responsible for the effectiviness of these safety concepts in combination with the Leica Geosystems equipment.
Responsibilities of the person in charge of the instrument:
WARNING
The person responsible for the instrument must ensure that the equipment is used in accor­dance with the instructions. This person is also accountable for the deployment of personnel and for their training and for the safety of the equipment when in use.
The person in charge of the instrument has the following duties:
2
Leica DISTO™ D3a BT 776750 gb
To understand the safety instructions on the product and the instructions in the User Manual.
To be familiar with local safety regulations relating to accident prevention.
To inform Leica Geosystems immediately if the equipment becomes unsafe.
Hazards in use
CAUTION:
Watch out for erroneous distance measure­ments if the instrument is defective or if it has been dropped or has been misused or modified.
Precautions:
Carry out periodic test measurements. Particularly after the instrument has been subject to abnormal use, and before, during and after important measure­ments. Make sure the Leica DISTO™ optics is kept clean and that there is no mechanical damage to the bumpers.
CAUTION:
In using the instrument for distance measure­ments or for positioning moving objects (e.g. cranes, building equipment, platforms, etc.) unforeseen events may cause erroneous measurements.
Precautions:
Only use this product as a measuring sensor, not as a control device. Your system must be configured and operated in such a way, that in case of an erroneous measurement, malfunction of the device or power
failure due to installed safety measures (e.g. safety limit switch), it is assured that no damage will occur.
WARNING:
Flat batteries must not be disposed of with household waste. Care for the environment and take them to the collection points provided in accordance with national or local regulations.
The product must not be disposed of with household waste. Dispose of the product appropriately in accordance with the national regulations in force in your country. Always prevent access to the product by unauthorized personnel.
management information can be downloaded from the Leica Geosystems home page at
http://www.leica-geosystems.com/treatment or received from your Leica Geosystems dealer.
Product specific treatment and waste
Electromagnetic Compatibility (EMC)
The term "electromagnetic compatibility" is taken to mean the capability of the product to function smoothly in an environment where electromagnetic radiation and electrostatic discharges are present, and without causing electromagnetic interference to other equipment.
D
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
Leica DISTO™ D3a BT 776750 gb
3
Safety Instructions
D
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
WARNING:
The Leica DISTO™ conforms to the most strin­gent requirements of the relevant standards and regulations. Yet, the possibility of it causing interfer­ence in other devices cannot be totally excluded.
CAUTION:
Never attempt to repair the product yourself. In case of damage, contact the local dealership.
FCC statement (applic. in U.S.)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter­ference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter­mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
WARNING:
Changes or modifications not expressly approved by Leica Geosystems for compliance could void the user’s authority to operate the equipment.
Use of the product with BLUETOOTH®:
WARNING:
Electromagnetic radiation can cause distur­bances in other equipment, in installations (e.g. medical ones such as pacemakers or hearing aids) and in aircraft. It can also affect humans and animals.
Precautions:
Athough this product conforms to the most stringent standards and regulations, Leica Geosystem cannot totally exclude the possibility of harm to people and animals.
Do not use the product near petrol stations,
chemical plants, in areas with a potentially explo­sive atmosphere and where blasting takes place.
Do not use the product near medical equipment.
Do not use the product in airplanes.
Safety Instructions
4
Leica DISTO™ D3a BT 776750 gb
Do not use the product near your body for extended periods.
CAUTION:
Never attempt to repair the product yourself. In
case of damage, contact the local dealership.
Laser classification
Integrated distancemeter
The Leica DISTO™ produces a visible laser beam which emerges from the front of the instrument.
It is a Class 2 laser product in accordance with:
IEC60825-1 : 2007 "Radiation safety of laser products"
Laser Class 2 products:
Do not stare into the laser beam or direct it towards other people unnecessarily. Eye protection is normally afforded by aversion responses including the blink reflex.
WARNING:
Looking directly into the beam with optical aids
(e.g. binoculars, telescopes) can be hazardous.
Precautions:
Do not look directly into the beam with optical aids.
CAUTION:
Looking into the laser beam may be hazardous
to the eyes.
Precautions:
Do not look into the laser beam. Make sure the laser is aimed above or below eye level. (particularly with fixed installations, in machines, etc.)
D
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
Leica DISTO™ D3a BT 776750 gb
5
Safety Instructions
D
Laser Radiation
Do not stare into the beam
Laser class 2
acc. IEC 60825-1:2007
Maximum radiant power: <1mW Emitted wavelength: 620-690nm Beam divergence: 0.16 x 0.6 mrad Pulse duration: 1 x 10 -9 s
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
Labelling
Position of the product label:
Start-up
Inserting/replacing batteries
1 Remove battery compartment lid and attach
handstrap. 2 Insert batteries, observing correct polarity. 3 Close the battery compartment again. Replace
the batteries when the symbol flashes perma-
nently in the display.
Only use alkaline or rechargeable batteries.
)
Remove the batteries before any long period
)
of non-use to avoid the danger of corrosion.
Start-up
6
Leica DISTO™ D3a BT 776750 gb
Changing the reference point (multifunctional endpiece)
The instrument can be adapted for the following measuring situations:
For measurements from an edge, fold out the positioning bracket until it first locks in place.
For measurements from a corner, open the posi­tioning bracket until it locks in place, then push the positioning bracket lightly to the right to fold it out fully.
A built-in sensor automatically detects the orienta­tion of the positioning bracket and adjusts the zero point of the instrument accordingly.
Keypad
1
2
3
10
5
9
7
12
1ON / DIST (On/measuring) - button 2 Horizontal distance - button 3 Plus (+) - button 4 Minus (-) - button 5Area / volume - button 6 Storage - button 7 Reference - button 8Functions - button 9Timer - button 10 Second function button 11 Menu/equal - button 12 Clear/off - button 13 Bluetooth button
13
11
4
6
8
D
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
Leica DISTO™ D3a BT 776750 gb
7
Start-up
GB
1 2
3
4
21 30
22 31
32
5
20 29
6
13
15,16
14
7,8,9
19
18172733
12
28 10,11
23
24
25
26
NL
DK
FIN
CN
ROK
RUS
D
Display
F
I
E
S
N
J
PL
H
CZ
1Laser active 2 Reference (front) 3 Reference (rear) 4 Reference (corner stop) 5 Measuring with the tripod 6 Stake out function 7 Single Pythagoras measurement 8 Double Pythagoras measurement 9 Double (partial height) measurement 10 Save constant value, call up constant value 11 Historical memory, call up values 12 Spirit level (numeric)
Start-up
13 Battery status 14 Area/volume 15 Tilt 16 Horizontal distance measurement using tilt 17 Triangle area 18 Timer 19 Menu 20 Circumference 21 Wall area 22 Ceiling area 23 Intermediate line 1 24 Intermediate line 2 25 Intermediate line 3 26 Summary line 27 Information 28 Spirit level 29 Tilt angle 30 Distance measured 31 Indirect height 32 Detail display 33 Bluetooth Icon
8
Leica DISTO™ D3a BT 776750 gb
Menu functions
EXIT
3
4
5
6
7
2
1
0.0°
Settings
The menu allows settings to be altered and perma­nently stored. After switching off the device or replacing the batteries the settings are stored.
Navigation in the menu
The menu allows settings to be made at the user level. The instrument can be specifically configured to your personal requirements.
General description
button (pressed long) - You are in the , the units set and the first menu item "Unit" are displayed.
button (pressed short) pages through each menu item.
or button to make changes in menu items. button (pressed short) brings up the next menu
item. A long press on the button in the menu confirms
the new settings made in the submenu items . Pressing the button for longer in the menu
allows you to quit the settings function without saving.
D
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
Leica DISTO™ D3a BT 776750 gb
9
Menu functions
D
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
Setting the unit for distance measurements
The following units can be set:
Distance Area Volume
1. 0.000 m
2. 0.000
3. 0.00 m
4. 0.00 ft
5. 0'00''
6. 0.0 in
7. 0
0
1
/
32
m
1
/
32
in
0.000 m² 0.000 m³
0.000 m² 0.000 m³
0.000 m² 0.000 m³
0.00 ft² 0.00 ft³
0.00 ft² 0.00 ft³
0.00 ft² 0.00 ft³
0.00 ft² 0.00 ft³
Setting the unit for tilt measurements
The following units can be set for tilt measurements:
Units for tilt
1.
2.
+/- 0.0°
0.00%
Measuring with the tripod ( )
The reference must be appropriately adjusted in order to be able to take correct measurements with a tripod. To do this select ON in this menu item. You can switch the reference on the tripod on or off. The setting can be seen on the display .
Beep ( )
You can switch the beep on or off.
Level in status field ( )
The level (in °) in status field can be switched on or off.
Display illumination ( )
The display illumination can be turned on or off.
Menu functions
10
Leica DISTO™ D3a BT 776750 gb
Reset - returning the instrument to the factory settings ( )
The instrument has a RESET function. When you select the menu function RESET and confirm, the instrument defaults to the factory settings.
A reset returns the following values to their factory settings:
Reference (rear)
Display illumination (ON)
•Beep (ON)
Unit (m(mm))
Stack and memory are erased
All customised settings and stored values are
)
also lost.
Operation
Switching on and off
Switches on the instrument and laser. The display shows the battery symbol until the next button is pressed.
Pressing this button for longer switches the instrument off.
The instrument switches off automatically after six minutes of inactivity.
CLEAR button
The last action is cancelled. While making area or volume measurements, each single measure­ment can be deleted and remeasured in series.
Reference setting
The default reference setting is from the rear of the instrument.
Press this button to take the next measurement from the front edge . A special beep sounds when­ever the reference setting is changed.
After a measurement the reference returns automat­ically to the default setting (rear reference).
Press this button for longer the front reference
is set permanently.
Press this button, the rear reference is set again.
D
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
Leica DISTO™ D3a BT 776750 gb
11
Operation
D
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
Measuring
Single distance measurement
Press to activate the laser. Press again to trigger
the distance measurement. The result is displayed immediately.
Tilt measurement
The tilt sensor measures tilts between ± 45°.
)
During the measurement of tilt, the instru-
)
ment should be held without transverse tilt, as far as possible, (± 10°).
Horizontal measurement
Press button to activate horizontal measure­ment in the instrument. The following symbol appears in the display . If the button is active, the horizontal distance is displayed in the summary line for each distance measurement (up to max. +/­45° and up to max. a transverse tilt of +/-10°).
Press the button for longer to display additional information on the measurement, for example the tilt angle , the distance measured and the indi­rect height .
Press button again to switch off horizontal
measurement.
Measuring
Minimum/maximum measurement
This function allows the user to measure the minimum or maximum distance from a fixed measuring point. It can also be used as to determine spacings.
min. max.
It is commonly used to measure room diagonals (maximum values) or horizontal distances (minimum values).
Press and hold down this button until you hear a beep. Then slowly sweep the laser back and forth and up and down over the desired target point - (e.g. into the corner of a room).
Press to stop continuous measurement. The values for maximum and minimum distances are shown in the display as well as the last measured value in the summary line.
12
Leica DISTO™ D3a BT 776750 gb
Laser continuous
Press and hold down the key when switching
on the device until the character appears perma-
nently in the display and a beep sounds. Every further press of the key releases a distance measure­ment.
Press the key and hold to switch the device
and Laser continuous operation off.
If the laser is in continuous operation mode,
)
the device switches off automatically after 15 minutes.
Functions
Addition / subtraction
Distance measuring.
The next measurement is added to the previous one.
The next measurement is subtracted from the previous one.
This process can be repeated as required.
Press this button and the result is then always
shown in the summary line.
The last step is cancelled.
Area
Press once. The symbol appears in the display.
Press this button to take the first length measurement (e.g. length).
Press it again to take the second length measurement (e.g. width).
The result is displayed in the summary line. Press the button for longer to calculate the
circumference .
D
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
Leica DISTO™ D3a BT 776750 gb
13
Functions
D
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
Volume
Press this button twice. The symbol
appears in the display.
Press this button to take the first length
measurement (e.g. length).
Press this button to take the second length
measurement (e.g. width).
Press this button to take the third length measure-
ment (e.g. height). The volume then appears in the summary line. Press the button for longer to display additional
room information such as ceiling/floor area , surface area of the walls , circumference .
Tilt measurement
Press this button once to activate the tilt sensor. The symbol appears in the display. The tilt is continuously shown as ° or % depending on the setting.
Press to measure the inclination and the distance.
Functions
14
Leica DISTO™ D3a BT 776750 gb
Triangular area
11
2
3
0.625 m
0.625 m
0.625 m
0.625 m
0.625 m
1.025 m
The area of a triangle can be calculated by the measurement of three sides.
Press the key two times - the triangle symbol
appears in the display.
Press the key and measure the first side of the
triangle.
Press the key and measure the second side of
the triangle.
Press the key and measure the third side of the
triangle. The result is shown in the summary row.
Press and hold the key to display additional infor­mation about the measurement, such as the angle included by the first two measurements and the perimeter of the triangle .
Leica DISTO™ D3a BT 776750 gb
Stake out function
Two different distances (a and b) can be entered into the instrument and can then be used to mark off defined measured lengths, e.g. in the construction of wooden frames.
Entering stake out distances:
Press this button three times and the stake out
function symbol appears in the display .
The value (a) and the corresponding intermediate line flash.
By using and , you can adjust the values (first a and then b) to suit the desired stake out distances. Holding the buttons down increases the rate of change of the values.
Once the desired value (a) has been reached it can be confirmed with the button.
The value (b) and the intermediate line flashes (the
15
a
b
b
Functions
D
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
D
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
defined value (a) is automatically adopted). Value (b) can be entered using and . The defined value (b) is confirmed with the button.
Pressing the button starts the laser measure­ment. The display shows required stake out distance in the summary line between the stake out point (first a and then b) and the instrument (rear refer­ence).
If the DISTO™ is then moved slowly along the stake out line the displayed distance decreases. The instru­ment starts to beep at a distance of 0.1m from the next stake out point.
The arrows in the display indicate in which direc­tion the DISTO™ needs to be moved in order to achieve the defined distance (either a or b). As soon as the stake out point is reached the beep changes.
The function can be stopped at any time by pressing the button.
a
b
b
Indirect measurement
The instrument can calculate distances using Pythagoras’ theorem.
Make sure you adhere to the prescribed
)
sequence of measurement:
Al l target p oints must be in a horizonta l or vertical plane.
The best results are achieved when the instru­ment is rotated about a fixed point (e.g. with the positioning bracket fully folded out and the instrument placed on a wall).
The minimum/maximum function can be used ­see explanation in "Measuring -> Minimum/ maximum measurement". The minimum value must be used fo r me asu rem en ts at ri ght ang les to the target; the maximum distance for all other measurements.
Make sure that the first measurement and the
)
distance to be measured are at right angles. Use the Minimum/maximum function, as explained in "Measuring -> Minimum/maximum measurement".
Functions
16
Leica DISTO™ D3a BT 776750 gb
Indirect measurement - determining a dis-
1
2
3
tance using 2 auxilliary measurements
e.g. for measuring building heights or widths. It is helpful to use a tripod when measuring heights that require the measurement of two or three measurements.
Press this button four times, the display shows
the following symbol . The laser is switched on.
Aim at the upper point (1) and trigger the measurement. After the first measurement the value is adopted. Keep the instrument as horizontal as possible.
Press and hold down this button to trigger continuous measurement, sweep the laser back and forth and up and down over the ideal target point.
Press to stop continuous measurement (2). The result is displayed in the summary line, the partial results in the secondary line.
Indirect Measurement - determining a dis­tance using 3 measurements
Press this button five times; the display shows the following symbol . The laser is switched on.
Aim at the upper point (1) and trigger the measurement. After the first measurement the value is adopted. Keep the instrument as horizontal as possible
Press and hold down this button to trigger continuous measurement, sweep the laser up and down over the ideal target point.
Press to stop continuous measurement (2). The
D
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
Leica DISTO™ D3a BT 776750 gb
17
Functions
D
12
3
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
value is adopted. Aim at the lower point and
press this button to trigger the measurement (3). The result is displayed in the summary line, the partial results in the secondary lines.
Indirect measurement - determining a chain value using 3 measurements
e.g. determining the height between point 1 and point 2 using three target points.
Press this button six times; the display shows the following symbol . The laser is switched on.
Aim at the upper point (1).
Press this button and trigger the measurement. After the first measurement the value is adopted. The display flashes (2).
Functions
Triggers the measurement. After the second measurement the value is adopted. The display flashes (3).
Press and hold down this button to trigger continuous measurement. Sweep the laser up and down over the ideal target point.
Press this button to end continuous measure­ment. The result is displayed in the summary line, the partial results in the secondary lines.
Storage of constants/historical storage
Storage of a constant
You can store and recall a frequently used value e.g. height of a room. Measure the desired distance, press and hold the button until the device beeps to confirm storage.
Recalling the constant
Press this button once to recall the constant and make it available for further calculations by pressing button .
Adjusting the constant
Press the button for longer to change the constant
- the constant flashes, you can now change the
18
Leica DISTO™ D3a BT 776750 gb
constant to the required value using the or button. Press the button to save the constant.
Historical storage
Press this button twice and the previous 20 results (measurements or calculated results) are shown in reverse order.
The and buttons can be used for navigation.
Press this button to use a result from the summary line for further calculations.
Pressing the and buttons at the same time erases all the values in historical storage.
Timer (self-triggering)
Press this button to set a 5-second time delay. or
Press and hold down this button until the desired time delay is reached (max. 60 seconds).
Once the key is released the remaining seconds until measurement (e.g. 59, 58, 57...) are displayed in a countdown. The last 5 seconds are counted down with a beep. After the last beep the measurement is taken and the value is displayed.
The timer can be used for all measurements.
)
Working with BLUETOOTH®
Switching on BLUETOOTH® / sending measurements
A quick press on the - key starts DISTO™ BLUE­TOOTH®. The data connection must then be estab­lished out from a Pocket PC / PC by the application software. A BLUETOOTH® - icon will appear in the display until this has been successfully completed. BLUETOOTH® automatically switches off if the connection to the Pocket PC / PC is not established within 240 sec from when the BLUETOOTH® was switched on.
Whilst the first connection between the
)
Pocket PC/PC and the DISTO™ is being established, a prompt for the Pin-code of the DISTO™ may be displayed. In this case, enter the code 0000 into your Pocket PC/PC.
Switching off BLUETOOTH®
BLUETOOTH® switches off as soon as the DISTO™ is switched off.
D
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
Leica DISTO™ D3a BT 776750 gb
19
Working with BLUETOOTH®
D
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
The direction keys
Eight direction keys (identified by a small arrow near the key) on the operator's keypad are used to manoeuvre the cursor. The direction keys become active when you switch to the second level (by pressing the key). The distance measuring key is active in both levels. The functionality of the direction keys depends on the software used.
Transmitting the measurement
If your software supports the direction keys use them to select the appropriate position for the cursor.
Press the button briefly to transfer the value from the summary row to the pocket PC / PC.
Press the botton long to transfer all values from the display.
For further details please consult your manual for the software used.
During data transmission
If the data is not confirmed as being successfully received by the Pocket PC/ PC then no new measure­ment can be processed. The Info code "240" appears in the display if no data transmission has taken place after 2 seconds. Press the - key and repeat
the measurement and then transmit it.
The free software supplied is designed to
)
provide the user with basic functionality. Leica Geosystems provides no warranty for this free soft­ware and offers no support for it. Leica Geosystems accepts no liability whatsoever arising from the use of the free software and is not obliged to provide corrections nor to develop updates or upgrades. You can find numerous commercial vendors of soft­ware for a wide range of applications on our homepage.
Appendix
Message codes
All message codes are displayed with either or "Error". The following errors can be corrected:
Cause Remedy
156
Transverse tilt greater than 10°
160
Main tilt direction, angle too high (> 45°)
204
Calculation error Repeat procedure
240
Data transfer error Repeat procedure
Hold the instrument without any transverse tilt
Measure angle up to max. ± 45°
Appendix
20
Leica DISTO™ D3a BT 776750 gb
Cause Remedy
245
2nd button pressed although no Blue­tooth connection exists.
252
Temperature too high
253
Temperature too low
255
Receiver signal too weak, measurement time too long, distance > 100 m
256
Received signal too strong
257
Wrong measure­ment, background brightness too high
260
Laser beam inter­rupted
Error Cause Remedy
Error Hardware error Switch on/off the
Establish Bluetooth connection
Cool down instrument
Warm up instrument
Use target plate
Target too reflective (use target plate)
Darken target (measure in different lighting conditions)
Repeat measurement
device several times. If the symbol still appears, then your instrument is defective. Please call your dealer for assistance.
Technical data
Distance measurements:
Measuring accuracy* up to 10 m (2 σ, standard deviation)
Power Range Technology™: Range (use target plate from about 80m)
Smallest unit displayed 0.1 mm Distance measurement Minimum/maximum
measurement, Continuous measurement
Area/volume calculation of room data
Addition / subtraction Indirect measurement
using Pythagoras
Tilt measurements:
Tilt sensor: Accuracy (2 σ, standard deviation)
- to laser beam
- to the housing Horizontal measurement Indirect measurement
using tilt sensor (direct horizontal distance)
Angle measurement using tilt sensor(
± 45°)
typically: ± 1/16 in*
(+/- 1.0mm)
0.05 m to 100 m 2 in. to 325 ft
9
9
9
9
9
± 0.3° ± 0.3°
9
9
9
D
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
Leica DISTO™ D3a BT 776750 gb
21
Appendix
D
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
General:
Laser class II Laser type 635 nm, < 1 mW Ø laser point
(at distances) Autom. laser switch-off after 3 min Autom. instrument
switch-off Display illumination Multifunctional endpiece Timer (self-triggering) Save constant value Historical storage
(20 values) BLUETOOTH® 2.0 Range of BLUETOOTH®
Cl. 2 Tripod thread Battery life,
Type AAA, 2 x 1.5V Protection against
splashes and dust Dimensions 127 x 49 x 27.3 mm
Weight (with batteries) 150 g Temperature range:
Storage
Operation
6 / 30 / 60 mm
(10 / 50 / 100 m)
after 6 min
9 9 9 9
9
9
10 m
9
up to
5 000 measurements
IP 54, dust-proof,
splash-proof
5 x 1.93 x 1.06 in
-25°C up to +70°C
(-13°F up to +158°F)
-10°C up to +50°C
(14°F up to +122°F)
* maximum deviation occurs under unfavourable conditions such as bright sunlight or when measuring to poorly reflecting or very rough surfaces. Measuring accuracy between 10 m and 30 m may deteriorate to approx. ± 0.025 mm/m, for distances above 30 m to ± 0.1 mm/m.
Measuring conditions
Measuring range
The range is limited to 100 m. At night or dusk and if the target is in shadow the
measuring range without target plate is increased. Use a target plate to increase the measurement range during daylight or if the target has poor reflec­tion properties.
Target surfaces
Measuring errors can occur when measuring toward colourless liquids (e.g. water) or dust free glass, Styrofoam or similar semi-permeable surfaces.
Aiming at high gloss surfaces may deflect the laser beam and lead to measurement errors.
Against non-reflective and dark surfaces the measuring time may increase.
Appendix
22
Leica DISTO™ D3a BT 776750 gb
Care
Do not immerse the instrument in water. Wipe off dirt with a damp, soft cloth. Do not use aggressive cleaning agents or solutions. Handle the instrument as you would a telescope or camera.
Warranty
The Leica DISTO™ D3a BT comes with a three* year warranty from Leica Geosystems AG.
More detailed information can be found at:
www.disto.com
All illustrations, descriptions and technical specifica­tions may be subject to change without prior notice.
* To receive the three year warranty, the product must be regis­tered on our website www.disto.com within eight weeks of the purchase date. If the product is not registered, a two year warranty applies.
D
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
Leica DISTO™ D3a BT 776750 gb
23
Appendix
D
GB
F
I
E
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
Appendix
24
Leica DISTO™ D3a BT 776750 gb
Leica Geosystems AG CH-9435 Heerbrugg (Switzerland) www.disto.com
Leica Geosystems AG, Heerbrugg, Switzerland has been certified as being equipped with a quality system which meets the International Standards of Quality Management and Quality Systems (ISO standard 9001) and Environmental Management Systems (ISO standard 14001).
Total Quality Management - Our commitment to total customer satisfaction. Ask your local Leica Geosystems agent for more information about our TQM program.
Copyright Leica Geosystems AG, Heerbrugg, Switzerland 2010 Translation of original text (776750)
Pat. No.: WO 9427164, WO 9818019, WO 0244754, WO 0216964,
US 5949531, EP 1195617, US 7030969, WO 03104748
Loading...