La Crosse Technology WS-9055TWC, WS-9055TWC User Manual
WS-9055TWC
Wireless 433 MHz
Weather Station
Instruction Manual
TABLE OF CONTENTS
Topic Page
Quick Setup 3-5
Inventory of Contents 6-7
Detailed Setup Guide
Battery Installation 7
Setting the Time 8
Features
Minimum and Maximum
Temperatures
Resetting Minimum and
Maximum Temperatures
Adding additional remote
temperature sensors
(optional)
Weather Forecast 12
Weather Icons 13-14
Tendency Arrow 14
Mounting 15-16
Troubleshooting 16-18
Maintenance and Care 18-19
Specifications 19-20
Warranty Information 21-26
9
10
10-11
2
QUICK SETUP
Hint: Use good quality Alkaline
Batteries and avoid rechargeable
batteries.
1. Have the indoor temperature
station and remote temperature
sensor 3 to 5 feet apart.
2. Batteries should be out of both
units for 10 minutes.
3. Place the batteries into the
remote temperature sensor first
then into the indoor temperature
station.
(All remote temperature sensors must
be started before the indoor
temperature station)
4. DO NOT PRESS ANY
BUTTONS FOR 15 MINUTES.
In this time the indoor temperature
station and remote temperature sensor
3
will start to talk to each other and the
display will show both the indoor
temperature and an outdoor
temperature. If the indoor
temperature station does not display
both temperatures after the 15
minutes please retry the set up as
stated above. After both indoor and
outdoor temperatures are displayed
for 15 minutes you can place your
remote temperature sensor outdoors
and set your time.
The remote temperature sensor
should be placed in a dry, shaded
area. The remote temperature sensor
has a range of 80 feet. Any walls that
the signal will have to pass through
will reduce distance. An outdoor
wall or window can have up to 30
feet of resistance and an interior wall
can have up to 20 feet of resistance.
4
Your distance plus resistance should
not exceed 80 ft. in a straight line.
NOTE: Fog and mist will not harm
your remote temperature sensor but
direct rain must be avoided.
To complete the set up of your indoor
temperature station after the 15
minutes have passed please follow the
steps in the detailed set up guide on
page 8.
INVENTORY OF CONTENTS
1.
The indoor weather station (Figure
1)
2.
The remote temperature sensor
(TX6U) and mounting bracket.
(Figure 2)
3.
3 each, 1/2” Philips screws.
4.
One strip of double sided adhesive
tape.
5.
Instruction Manual and Warranty
Card.
5
Figure 1
ADDITIONAL EQUIPMENT
(not included)
1.
1 Philips screwdriver.
2.
2 Fresh AA Alkaline batteries.
3.
2 Fresh AA Alkaline batteries
DETAILED SETUP
GUIDE
Battery Installation
Figure 2
Holder
6
1. Install 2 AA batteries in the remote
temperature sensor. Make sure they
do not spring free, or start-up
problems may occur.
2.
Install 2 AA batteries in the indoor
weather station. Do not press any
buttons for
at least
fifteen
minutes.
Setting the time
1. Press and hold the “SET” key for 4
seconds.
2. The hour will flash.
3. Press and release the “+” key to
advance the hour.
4. Press and release the “SET” key.
5. The minute is flashing.
6. Press and release the “+” key to
advance the minutes.
7
7. Press and release the “SET” key to
exit programming.
FEATURES
Minimum and Maximum
Temperatures
1.
Press and release the “MIN/MAX”
button, “MAX” appears between the
indoor and remote temperatures.
2.
The recorded maximum indoor and
remote temperature is displayed.
3.
Press and release the “MIN/MAX”
button.
4.
“MIN” appears between the indoor
and remote temperatures.
5.
The recorded minimum temperature
is displayed.
6.
Press and release the “MIN/MAX”
button to exit min/max mode.
7.
To view optional additional sensors,
press and release the “CH” button
8
Loading...