1
LCD
Display
Function key
Stand
Function keys
WS-9060U-IT FORECAST STATION
Battery
compartment
Hanging
hole
2
3
+ key
MIN/MAX key
SET key
4
New
Moon
Waning
Crescent
First
Quarter
Waxing
Gibbous
Waxing
Crescent
Last
Quarter
Full
Moon
Waning
Gibbous
Bar segment (moon phase indicator)
INTRODUCTION:
Congratulations on purchasing this state-of-the-art
weather station as an example of innovative design and
quality piece of engineering. Providing time, calendar,
weather forecast, moon phase, indoor and outdoor
temperature, indoor and outdoor relative humidity. This
unit will never keep you guessing on current and future
weather conditions.
The Weather Station
FEATURES:
x 12/24 hour time display
x Calendar display (year shows only in set mode)
x Display 8 Moon phases throughout the year
x Weather forecasting with weather tendency indicator
x Indoor and outdoor temperature display with
MIN/MAX records
x Temperature display in ºC/ ºF
x Indoor and outdoor humidity display
x Humidity data display as RH%
x Low battery indicator
Quick Setup Guide
INITIAL SETUP:
Do not mix old and new batteries. Do not mix alkaline,
standard, or rechargeable batteries
1. Install batteries (2-AAA LR3, 1.5V) into the Thermohygro Transmitter according to polarity.
2. Install batteries (2-AAA LR3, 1.5V) into the Weather
Station according to polarity.
3. Place the transmitter and weather station 5-10 feet
apart. When the batteries are inserted, the weather
station will start receiving data signal from the
transmitter. The outdoor temperature and humidity
data should be displayed on the weather station.
4. If this does not happen after 2 minutes, the batteries
will need to be removed from both units and reset
from step 1.
5. If the outdoor temperature and humidity are
displayed for 15 minutes, the transmitter can be
placed outside.
Note:
When changing batteries in the units, ensure the batteries
do not spring free from the contacts. Always wait at least
15 minutes after removing the batteries before reinserting,
otherwise start up and transmission problems may occur.
TO INSTALL AND REPLACE BATTERIES IN THE
THERMO-HYGRO TRANSMITTER
The outdoor thermo-hygro transmitter uses 2 x AAA, IEC
LR3, 1.5V batteries. To install and replace the batteries,
please follow the steps below:
setting up procedures. This is due to a random security
code assigned by the transmitter at start-up. This code
must be received and stored by the weather station in the
first 3 minutes of power being supplied to the transmitter.
1. Remove the battery cover.
2. Insert the batteries, observing the
correct polarity (see battery
compartment marking).
3. Replace the battery cover on the unit.
Note:
When changing batteries in any of the units,
all units need to be reset by following the
TO INSTALL AND REPLACE BATTERIES IN THE
WEATHER STATION
The weather station uses 2 x AAA, IEC LR3, 1.5V
batteries. To install and replace the batteries, please follow
the steps below:
BATTERY CHANGE:
It is recommended to replace the batteries in all units on
an annual basis to ensure optimum accuracy of these
units.
FUNCTION KEYS:
Weather Station:
The Weather Station has 3 easy to use function keys: 1
key on the front, and 2 keys on the back
Please participate in the preservation of
the environment. Return used batteries to
an authorized depot.
1. Insert finger or other solid
object in the space at the
bottom center of the
battery compartment and
lift up to remove the
cover.
2. Insert batteries observing
the correct polarity (see
marking).
3. Replace compartment
cover.
MANUAL SETTINGS: The SET key will move you through
the program menu. The + key will change a value.
12/24-HOUR TIME: Hold the SET key and 12h or 24h will
flash. Use the + key to select 12-hour or 24-hour time.
Press and release the SET key to confirm and continue.
HOUR: The Hour will flash. Use the + key to select the
Hour. Press and release the SET key to confirm and
continue.
MINUTES: The Minutes will flash. Use the + key to select
the Minutes. Press and release the SET key to confirm
and continue.
YEAR: The Year will flash. Use the + key to select the
Year (the year will not display on the weather station).
Press and release the SET key to confirm and continue.
MONTH: The Month will flash. Use the + key to select the
Month. Press and release the SET key to confirm and
continue.
DATE: The Date will flash. Use the + key to select the
Date. Press and release the SET key to confirm and
continue.
°F/°C TEMPERATURE: °F/°C will flash. Use the + key to
select the °F or °C . Press and release the SET key to
confirm and exit the manual settings.
MOON PHASES SYMBOL
The moon icon of the weather station will also display all 8
moon phases throughout the year according to the set
calendar. A bar segment above the moon phase will
indicate current moon phase.
WEATHER FORECASTING ICONS:
The weather icons in the second section of LCD can be
displayed in any of the following combinations:
5
For every sudden or significant change in the air pressure,
6
Moon
phase
icon
Weather
tendency
indicator
Calendar
Indoor
relative
humidity
in RH%
Indoor
temperature
in ºC/ºF
Weather
forecast icon
Outdoor data signal
reception indicator*
Outdoor
temperature
in ºC/ºF
Outdoor relative
humidity in RH%
Time
Low battery indicator
(weather station)
Low battery
indicator
(transmitter)
7
Mounting at a sheltered place. Avoid
hygro transmitter can be
8
the weather icons will update accordingly to represent the
change in weather. If the icons do not change, then it
means either the air pressure has not changed or the
change has been too slow for the Weather station to
register
The icons displayed forecasts the weather in terms of
getting better or worse and not necessarily sunny or rainy
as each icon indicates. All reading should be disregarded
for the first 48 hours after set up.
WEATHER TENDENCY INDICATOR
Working together with the weather icons is the weather
tendency indicators (located on the left and right sides of
the weather icons). When the indicator points upwards, it
means that the air-pressure is increasing and the weather
is expected to improve, but when indicator points
downwards, the air-pressure is dropping and the weather
is expected to become worse.
MIN/MAX DATA
VIEW THE MIN/MAX DATA
Press the MIN/MAX key several times to view the
MIN/MAX indoor temperature, and MIN/MAX outdoor
temperature sequentially.
RESET THE MIN/MAX DATA
Press and hold MIN/MAX key for 3 seconds to reset all
the indoor and outdoor temperature to current
temperatures.
LOW BATTERY INDICATOR
Low battery indicator is displayed on the LCD by the time
when the batteries require changing in the display. The
low battery indicator is displayed in the outdoor
temperature area when the batteries in the transmitter
require changing.
LCD SCREEN
The LCD screen is split into 5 sections displaying the
information for time/calendar, weather forecast, moon
phase, indoor data, and outdoor data.
* When the signal is successfully received by the weather
station, the outdoor transmission icon will be switched on.
(If not successful, the icon will not be shown on LCD). The
user can then easily see whether the last reception was
successful (icon on) or not (icon off).
THERMO-HYGRO TRANSMITTER
The temperature may affect the range of the thermo-hygro
transmitter. At cold temperatures the transmitting distance
may be decreased. Please bear this in mind when
positioning the transmitters. Also the batteries may be
reduced in power for the thermo-hygro transmitter.
POSITIONING THE THERMO-HYGRO TRANSMITTER
and humidity readings are receivable. In event that the
signal is not received, relocate the thermo-hygro
transmitter or the weather station slightly as this may help
the signal reception.
POSITIONING THE WEATHER STATION
The weather station provides the option of table standing
or wall mounting the unit. Before wall mounting, please
check that the outdoor data can be received from the
desired locations.
direct rain and sunshine.
The thermoplaced onto any flat surface or wall
mount using the bracket which
doubles as a stand or wall mount
base.
To wall mount:
1. Secure the bracket onto a desired wall
using the screws and plastic anchors.
2. Clip the transmitter onto the bracket.
Note:
Before permanently fixing the thermo-hygro to
the wall base, pace all units in the desired
locations to check that the outdoor temperature
To wall mount:
1. Fix a screw (not supplied) into the
desired wall, leaving the head
extended out by about 5mm.
2. Place the weather station onto
the screw, using the hanging hole
on the backside. Gently pull the
weather station down to lock the
screw into place.
Foldout table stand:
The foldout table stand leg is located
on the backside. Pull the stand out
from the bottom center edge of the
weather station, below the battery
compartment. Once the foldout table
stand is extended, place the weather
CARE AND MAINTENANCE:
x Extreme temperatures, vibration and shock should
be avoided as these may cause damage to the units
and give inaccurate forecasts and readings.
x When cleaning the display and casings, use a soft
damp cloth only. Do not use solvents or scouring
agents as they may mark the LCD and casings.
x Do not submerge the units in water.
x Immediately remove all low powered batteries to
avoid leakage and damage. Replace only with new
batteries of the recommended type.
x Do not make any repair attempts to the units. Return
it to their original point of purchase for repair by a
qualified engineer. Opening and tampering with the
units may invalidate their guarantee.
x Do not expose the units to extreme and sudden
temperature changes, this may lead to rapid
changes in forecasts and readings and thereby
reduce their accuracy.
SPECIFICATIONS:
Temperature measuring range:
Indoor : 14.2°F to +139.8°F with 0.2°F resolution
-9.9ºC to +59.9ºC with 0.1°C resolution
(“OF.L” displayed if outside this range)
Outdoor : -39.8°F to +139.8°F with 0.2°F resolution
-39.9ºC to +59.9ºC with 0.1°C resolution
(“OF.L” displayed if outside this range)
Indoor humidity range : 20% to 95% with 1% resolution
(Display “- -“ if temperature is OF.L; display “19%“ if < 20%
and “96%” if > 95%)
Outdoor humidity range : 1% to 99% with 1% resolution
(Display “- -“ if outside temperature is OF.L; display 1% if <
1% and 99% if > 99%)
Data checking intervals
station in an appropriate location.
9
Indoor temperature : every 16 seconds
10
11
12
Indoor humidity : every 64 seconds
Outdoor temperature and humidity: every 4 seconds
Transmission range : up to 260 feet (open space)
80 meters (open space)
Power consumption (alkaline batteries recommended):
Weather station : 2 x AAA, IEC LR3, 1.5V
Thermo-hygro transmitter : 2 x AAA, IEC LR3, 1.5V
Battery life : up to 12 months
Dimensions (L x W x H):
Weather station : 3.72” x 0.78” x 6.18”
94.6 x 20 x 157mm
Thermo-hygro transmitter : 1.41” x 0.62” x 4.03”
36 x 16 x 102.6mm
WARRANTY INFORMATION
La Crosse Technology, Ltd provides a 1-year limited
warranty on this product against manufacturing defects in
materials and workmanship.
This limited warranty begins on the original date of
purchase, is valid only on products purchased and used in
North America and only to the original purchaser of this
product. To receive warranty service, the purchaser must
contact La Crosse Technology, Ltd for problem
determination and service procedures. Warranty service
can only be performed by a La Crosse Technology, Ltd
authorized service center. The original dated bill of sale
must be presented upon request as proof of purchase to
La Crosse Technology, Ltd or La Crosse Technology,
Ltd’s authorized service center.
La Crosse Technology, Ltd will repair or replace this
product, at our option and at no charge as stipulated
herein, with new or reconditioned parts or products if found
to be defective during the limited warranty period specified
above. All replaced parts and products become the
property of La Crosse Technology, Ltd and must be
returned to La Crosse Technology, Ltd.
Replacement parts and products assume the remaining
original warranty, or ninety (90) days, whichever is longer.
La Crosse Technology, Ltd will pay all expenses for labor
and materials for all repairs covered by this warranty. If
necessary repairs are not covered by this warranty, or if a
product is examined which is not in need or repair, you will
be charged for the repairs or examination.
The owner must pay any shipping charges incurred in
getting your La Crosse Technology, Ltd product to a La
Crosse Technology, Ltd authorized service center.
Your La Crosse Technology, Ltd warranty covers all
defects in material and workmanship with the following
specified exceptions: (1) damage caused by accident,
unreasonable use or neglect (including the lack of
reasonable and necessary maintenance); (2) damage
occurring during shipment (claims must be presented to
the carrier); (3) damage to, or deterioration of, any
accessory or decorative surface; (4) damage resulting
from failure to follow instructions contained in your owner’s
manual; (5) damage resulting from the performance of
repairs or alterations by someone other than an authorized
La Crosse Technology, Ltd authorized service center; (6)
units used for other than home use (7) applications and
uses that this product was not intended or (8) the products
inability to receive a signal due to any source of
interference.
This warranty covers only actual defects within the product
itself, and does not cover the cost of installation or removal
from a fixed installation, normal set-up or adjustments,
claims based on misrepresentation by the seller or
performance variations resulting from installation-related
circumstances.
LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME
LIABILITY FOR INCIDENTAL, CONSEQUENTIAL,
PUNITIVE, OR OTHER SIMILAR DAMAGES
ASSOCIATED WITH THE OPERATION OR
MALFUNCTION OF THIS PRODUCT. THIS PRODUCT
IS NOT TO BE USED FOR MEDICAL PURPOSES OR
FOR PUBLIC INFORMATION. THIS PRODUCT IS NOT
A TOY. KEEP OUT OF CHILDREN’S REACH.
This warranty gives you specific legal rights. You may
also have other rights specific to your State. Some States
do no allow the exclusion of consequential or incidental
damages therefore the above exclusion of limitation may
not apply to you.
Contact info for warranty or technical support:
La Crosse Technology
Product Info and Support:
www.lacrossetechnology.com/9060
www.lacrossetechnology.com/support/register.php
All rights reserved. This handbook must not be
reproduced in any form, even in excerpts, or duplicated or
processed using electronic, mechanical or chemical
procedures without written permission of the publisher.
This handbook may contain mistakes and printing errors.
The information in this handbook is regularly checked and
corrections made in the next issue. We accept no liability
for technical mistakes or printing errors, or their
consequences.
All trademarks and patents are acknowledged.
FCC ID: OMO-TX45U-TH-IT (transmitter)
FCC DISCLAIMER
RF Exposure mobile:
The internal / external antennas used for this mobile
transmitter must provide a separation distance of at least
20 cm (8 inches) from all persons and must not be co-
Product Registration:
Contact Support: 1-608-782-1610
2817 Losey Blvd. S.
La Crosse, WI 54601
located or operating in conjunction with any other antenna
or transmitter."
Statement according to FCC part 15.19:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Statement according to FCC part 15.21:
Modifications not expressly approved by this company
could void the user's authority to operate the equipment.
Statement according to FCC part 15.105:
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
x Reorient or relocate the receiving antenna.
x Increase the separation between the equipment and
receiver.
x Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
x Consult the dealer or an experienced radio/TV
technician for help.
Loading...