Keyence FS-N12N, FS-N12CN, FS-N11EN, FS-N12EN, FS-N11MN Instruction Manual

1

Digital Fiber Sensor

FS-N10 Series

Instruction Manual

Hints on Correct Use

• Do not wire the amplifier line along with power lines or high-tension lines, otherwise the sen-

sor may malfunction or receive damage due to noise.

• When using a commercially available switching regulator, ground the frame ground terminal

and ground terminal.

• Do not use the FS series outdoors, or in a place where extraneous light can enter the light-

receiving surface directly.

• Due to the individual dispersion of characteristics and the difference in fiber unit model, the

maximum sensing distance or displayed value of all the units are not the same.

• If the sensor is used in S-APC mode for a long time, the LED indicators will be imposed with

a heavy load. In that case, the sensor will be automatically set to ACC mode where the cur­rent consumption of the sensor for light emission will be constant, and “END APC” will be
displayed. The sensor can be continuously used in this case. Replace the sensor, however, if
highly precise detection is required.



About UL Certification

The FS-N series is UL and C-UL certified, and is compliant with the UL and CSA standards.

• Applicable standards UL508 Industrial Control Equipment

CAN/CSA C22.2 No.14-M05 Industrial Control Equipment

• UL File No. E301717

• UL categories: NRKH, NRKH7

• Enclosure Type 1 (based on UL50 standard)



Notes on UL Certification

• The power source used with the FS-N series must be UL Listing cer tified for Class 2 output

as stipulated by US National Electric Code (NEC) NFPA70.

• Connect the FS-N12 and N14 to the FS-N11 and N13 main units for use.

Included accessories

• Instruction Manual 1pc.

• Fiber cutter 1pc.

FS-N10 Series Quick Start and Cabling



Quick Start

*1 This is a channel switch on 2-output types.
*2 Press and hold the [MODE] button to make advanced settings.



Cabling

Mounting Unit



Mounting on a DIN Rail

1 Align the claw at the bottom of the main body with

the DIN rail, as shown in figure1.
While pushing the main body in the direction of
the arrow 1, slant it in the direction of the arrow 2.

2 To dismount the sensor, raise the main body in

the direction of the arrow 3 while pushing the
main body in the direction of the arrow 1.



Installation on a Wall (Main Unit Only)

1 Attach the unit to the optional mounting bracket (OP-

73880), mount them together, and secure them with
two M3 screws as shown in figure2.

Connecting Fiber Unit

1 Open the dust cover in the direction shown by

arrow 1.

2 Move down the fiber lock lever in the direction

shown by a rrow 2.

3 Insert a fiber unit into the fiber insertion holes

to a length of the fiber insertion sign (i.e.,
approximately 14 mm).

4 Move down the fiber lock lever in the direction

shown by a rrow 4.

Failure to follow these instructions may lead to death or seri­ous injury.

Failure to follow these instructions may lead to injury.

Failure to follow these instructions may lead to product dam­age (product malfunction, etc.)

Provides additional information on proper operations that ca n be easily mistaken.

This provides tips about situations in which the feature being described is useful.

See "FS-N10 Series User's Manual" for details on the features of the FS-N 10 series and
detailed instructions for configuration.

•

This product is used to detect targets. Do not apply the
product to safety circuits for human protection.

• This product is not of explosion-proof construction. Do not

use the products in places with flammable gas, liquid, or
dust.

• This product is a sensor of DC power supply type. Do not

apply AC power. The product may explode or burn if an AC
voltage is applied.

Danger

Warning

Caution

Note

Note

Tip

Warning

See page 4 for information about connecting to external devices other than the FS­N11N.

• If a thin fiber unit is used, an adapter provided with the thin fiber unit will be
required.
Unless the correct adapter is connected, the thin fiber unit will not detect
targets correctly (the adapter is supplied with the fiber unit).

• To connect the coaxial reflective type fiber unit to the amplifier, connect the

single-core fiber to the transmitter side, and connect the multiple-core fiber
to the receiver side.

Fine sensitivity adjustment

Output switch

Press the [MODE] button once, then

to select L-on or D-onuse

Preset function

Configure easily
with a single press
when receiving light

DownUp

Power select switch *

1

Standard ⇔MEGA (fixed)

Setting value

Light intensity

Sensitivity setting

Press once each for workpiece/no workpiece

Note

Brown

Black

Blue

DC12-24V

Load

0V

3

2

figure1

1

OP-73880

figure2

Fiber insertion sign

1

3

2

4

Note

φ1.3

φ1.0

Adapter A

(OP-26500)

Adapter B

(OP-26501)

Cable outer dia Adapter Appearance

Receiver

Transmitter

Single-core fiber

Multi-core fiber

96M00603

2

Connecting Multiple Amplifiers

Up to 16 sub units can be connected to one main unit.

1 Remove the protection covers of the main unit and

sub unit(s).

2 Install the amplifiers one by one on the DIN rail.

3 Engage the two claws of the sub unit with the

recesses on the main unit side until you hear a
click.

4 Attach the end units (option: OP-26751) to the

both ends of the connected amplifiers in the same
way as in step (2).

5 Sandwich the amplifiers between the end units.

Tighten the screws at the top (two screws x two
units) with a Phillips screwdriver to fix the end
units.

Calibration Method



Detecting Even Small Differences

z

Two-point Calibration

Two-point calibration is the basic method for making calibration.
You can set the sensitivity level automatically, simply by pressing the [SET] button twice.
Just press once with the workpiece set up, and once without.

Two-point calibration performs detection at a location where there is a workpiece, and
another location where there is not, uses the intermediate value as the setting.
If the sensitivity difference does not have enough room, "- - - -" flashes for about two sec­onds after the calibration is complete. The set value is stored in memory even in that case.

Other Calibration Methods



Increase Resistance to Dust and Dirt

z

Maximum Sensitivity Setting

In the state shown below, press and hold the [SET] button for three seconds and stop push­ing when "5'6" flashes.
The sensitivity is set slightly higher than the light intensity.



Calibrate with Moving Workpiece

z

Full Auto Calibration

Press and hold the [SET] button with no workpiece in place, whil e “5'6” is flashing, pass
through a workpiece. (Continue pressing the [SET] button while the workpiece passes
through.)



Position Workpiece

z

Positioning Calibration

Press the [SET] button with no workpiece set.
Place the workpiece in the location you wish to position it, and press and hold the [SET] but­ton for at least 3 seconds. Release the button when "5'6" flashes.

Mount on DIN rail and install on metal sheeting when connecting to
multiple amplifiers or mounting main units together.

• Multiple connections cannot be made to equipment other than the FS-N10
series.

• Turn the power off before connecting multiple sub units.

• Do not touch the expansion connector with your bare hands.

Warning

Note

OP-26751 (a set of two)

Workpiece

Through-beam model setting method

Settings complete

Press [SET] button once with
no workpiece set

Press [SET] button once with
workpiece set

Reflective model setting method

Workpiece

Settings complete

Press [SET] button once with
no workpiece set

Press [SET] button once with
workpiece set

Workpiece

Through-beam model

: with

workpiece

set

Press and hold for 3 seconds or more

: without workpiece set

Reflective model

Press and hold for 3 seconds or more

Common to

Through-beam

and

ModelsReflective

Press and hold until
"

UGV

" flashes

Workpiece

While pressing the [SET] button

pass through a workpiece

Settings complete

Common to

Through-beam

and

Models

Reflective

Press [SET] button once with
no workpiece set

Workpiece

Press and hold [SET] button with

workpiece

set

Settings complete

Press and hold until
"

UGV

" flashes

3

Simple, User Friendly Functions



Easily Set up Display

z

Preset Function

With light ON, press the [PRESET] button. The current value is set to "".

Pressing the [PRESET] button changes the setting and current value as shown below.

• Presetting with preset disabled:

The setting is changed to "

". The setting can be changed via the normal calibration

method.

• Presetting with preset enabled:

Only the current value is changed to "

", and the setting is not changed.

z

Disable the Preset Function

Press and hold the [PRESET] button to disable the preset function.
When the preset function is disabled, the ratio of the setting and current values is main­tained as-is.



Set Current Value to "0"

z

The Zero Shift Function

This function is mainly used with reflective models.
Press the [PRESET] button and [ ] button at the same time.
The current value is set to "0".

z

Disable the Zero Shift Function

Press and hold the [PRESET] button to disable the zero shift function.



Set the current value to an adequate value when it is too
large (when saturated).

z

Use the Saturation Recovery Function

Press the [SET] button while pressing the [MODE] button to enable the saturation recovery
function.
The light transmission level and light intensity gain are calibrated automatically.

z

Disable Saturation Recovery

When the saturation recovery function is enabled, press th e [SET] button while pressi ng the
[MODE] button to cancel it.

Output Switch

Either light-ON (L-on) mode or dark-ON (D-on) mode can be selected.

1 While the current value is displayed, press the [MODE] button once.

2 Use to switch the output (.QP/&QP), then press the [MODE] button again.

The output switch completes, and the display returns to the current value.

Names of Each Part of the Main Unit

*1 Setting to "M" locks the power mode to MEGA mode. The two output type is a channel

switch .

*2 On the FS-N10Cx, this is an M8 connector rather than a cable. On the FS-N10Ex, this is an

e-CON connector.

• The preset function cannot be used tog ether with the zero shift func­tion. To use the zero shift function, you must first disable the preset
function.

• This is not suited to transparent workpieces and other cases of detec­tion with low light shielding.

Handy Uses for the Preset Function

This function is mainly useful when performing simple detection using a
through-beam model fiber unit (e.g. complete dark detection, such as when all
light axes of the fiber unit are shielded with opaque workpieces).

When you are using multiple FS-N10 series units simultaneously, this function
is an easy way to make all the displays uniform.

The zero shift and preset function cannot be used together. To use
the preset function, you must first disable the zero shift function.

Handy Uses for the Zero Shift Function

This function is mainly used to set the current value to "0" on a reflective
model fiber unit.

When a reflective model is first installed, the light intensity is sometimes not
set to "0".
If this happens, using the zero shift function to set the value to "0" when there
is no workpiece allows for easier understanding of the difference in light inten­sity.

Green "PST" lights up

Press [PRESET] button once
with no

workpiece

set

Setting is
"



"

Current value is
"



"

Note

Note

Tip

Green "PST" lights up

Current value is ""

Note

Note

Tip

Power mode Light intensity setting range

HSP, FINE, TURBO 2047 r 350

SUPER 4095 r 500

ULTRA, MEGA 5000 r 600

Handy Uses for the Saturation Recovery Function

This function is handy when the fiber unit becomes saturated after installation.
This eliminates the saturation via a simple operation, by automatically calibrat­ing the light transmission level and light intensity gain.

Press the [SET] button while
pressing the [MODE] button.

Set the light intensity to
within the range in the table below.

Note

Tip

Setting value
(Displayed in green)

Current value
(Displayed in red)

Dust cover

Fiber lock lever

Manual button

( )

MODE button (MODE)

Power select switch*

1

Cable*

2

Expansion
protective cover

Expansion connector

Preset button (PRESET)

SET button (SET)

Operation status indicators

Digital monitor

PST indicator

DTM indicator

4

Connecting to External Devices

*1 FS- N11N/N11MN/N13N only
*2 FS-N11MN only
*3 The FS-N13N/N14N has a white cable as separate output 2.

*1 FS-N11P/N13P/N13CP only
*2 The FS-N13P/N14P has a white cable as separate output 2.

The FS-N13CP/N14CP has the pin2 as separate output2.



FS-N11CN/N12CN/N11EN/N12EN



FS-N11CP/N12CP



Socket Cable (Sold Separately)

For FS-N11CN/N11CP/N12CN/N12CP/N13CP/N14CP

Error Displays and Corrective Actions

Initializing the Settings



Initializing Method

1 Press and hold the [SET] and [PRESET] buttons simultaneously for three seconds.

2 Use the to select "456", then press the [MODE] button.
3 Use the to select "K0K6", then press the [MODE] button.

After initialization is complete, the display returns to the current value.

z

Initial Settings

Using a Fiber Cutter and Cautions for Use



Using a Fiber Cutter

1 Inset the fiber into the cutter hole .
2 Bring down the blade in a single,

swift motion to cut the fiber.



Cautions for Using a Fiber Cutter

• When cutting a fiber unit to be attached to the FS-N10 series, be sure to use a gray fiber cut-

ter (OP-87098)

• Stopping the blade midway could cause a bad cut plane, reducing the detection range.

• Do not use the same hole twice.

Function Configuration



Basic Setting

*1 You can press the button to set between the range of 2 to 2.



FS-N11N/N12N/N11MN/N13N/N14N

Output Circuit Diagram I

nput Circuit Diagram (FS-N13N/N14N only)



FS-N11P/N12P/N13P/N14P/N13CP/N14CP

Output Circuit Diagram

Input Circuit Diagram (FS-N13P/N14P only)

Output Circuit Diagram Input Circuit Diagram

*FS-N11CN/N11EN only

Output Circuit Diagram Input Circuit Diagram

*FS-N11CP only

Error display Cause Solution

ErC Overcurrent in the control output.

Check the load and return the current
within the rated value.

ErE Failed to write/load the internal data. Perform initialization (p.4).

End APC Large load on the light source.

Replace the sensor if highly precise
detection is required.

0 V

DC12−24 V

DC5−30 V

Brown*

1

Black*

3

Monitor output(1−5V)*

2

Orange

Load

Device with input
impedance
10 Ω or more

Blue*

1

(Control output)

Sensor main circuit

Overcurrent

protection

circuit

Protection

circuit

Pink

DC3.3 V

Blue

PLC, etc.

0 V

Sensor main circuit

(Short-circuit current
1 mA or less)

Brown 1*

1

Blue 3*

1

Black 4*

2

0 V

DC12−24 V

Load

Sensor main circuit

Overcurrent

protection circuit

(Control output)

Pink

Brown

PLC, etc.

DC12−24 V

Sensor main circuit

(Short-circuit
current 2 mA
or less)

123

4

M8 connector Pin layout

0 V

DC12−24 V

DC5−30 V

Load

1*

3*

4

Sensor main circuit

Overcurrent

protection circuit

1

DC3.3 V

3*

PLC, etc.

0 V

Sensor main circuit

(Short-circuit current
1 mA or less)

123

4

M8 connector Pin layout

e-CON connector Pin layout

3*

1*

4

0 V

DC12−24 V

Load

Sensor main circuit

Overcurrent

protection circuit

2

1*

PLC, etc.

DC12−24 V

Sensor main circuit

(Short-circuit
current 2 mA
or less)

123

4

M8 connector Pin layout

e-CON connector Pin layout

OP-73864
(Cable length: 2 m)

OP-73865
(Cable length: 10 m)

1

2

3

4

Connected
pin No.

Pin - Pin and wire color table

1 Brown
2
3
4

White
Blue
Black

Core wire
cover color

Setting Initial Value

Power mode FINE

Detection mode Normal

Setting value 50

Output switch L-on

Failure to heed the cautions below could reduce the detection range.

Press and hold for 3 seconds or more

Fiber

Always insert fiber from the end with writing

Fiber cutter
(OP-87098)

2

1

MODE

Press and hold for 3 seconds or more

High Speed mode

Fine mode

Turbo mode

Super mode

Ultra mode

MEGA mode

Normal sensitivity setting method

Percentage Calibration*

1

Zero-shift calibration

Settings complete

Go to detection setup mode

Go to display setup mode

Go to system setup mode

MODE

MODE

MODE

MODE

J52

(KPG
6WT$
5W24

7.64
/')#

5V)
5V)
5V)

5'6









5VF

5'V2
15'V

'0&

(W0E
&K52

5;5

5'6
5'6

Return to normal display

MODE

5



Detection Settings

*1 Press the button to set between the range of  and (ms).

*2 Press the button to set the retouch sensitivity to a range of between

.'W and .'W

and set the warning output level to a range of between 12 and 2.

*3 Press the button to toggle between

Q((/Q0/-''2.

*4 Can be set between the range of  and .
*5 Can be set between the range of  and .

*6 Only external input types (FS-N11CN/N11CP/N11EN/N12EN/N13N/N13P/N14N/N14P).

*7 Only monitor output types (FS-N11MN).



Display Settings

*1 Press the button to toggle between 5VF/2`2A/D`DA/2AD`/2`DA
*2 Press the button to set between the range of 2 and 2.



System Settings

*1 Main unit only.



Two Ou tput

*2

*1 Press the button to set between the range of  and (ms).

*2 Only 2 output types (FS-N13N/N13P/N14N/N14P/N13CP/N14CP).

Normal (light intensity)
detection mode

DATUM1 mode *

2

Timer OFF

Off-delay timer *

1

On-delay timer *

1

One-shot timer *

1

DATUM2 mode *

2

Area detection mode

Rising Edge Detection Mode

Falling Edge Detection Mode

Settings complete

Go to display setup mode

Go to system setup mode

Return to original
detection setup mode

Do not use external input

External calibration input

Preset input

Zero shift input

Reset input

Transmission OFF input

Pause mode transition input *

3

Sleep mode transition input

Light emission power selection *

4

Analog scaling *

5

MODE

MODE

MODE

MODE

MODE

6Q((

Q((&
Q0&
5JQ6

5V)
5V)
5V)

&'VE

&'VE
&'VE
&'VE
&'VE
&'VE



5V) (W0E





5VF

&V/
&V/
#4'#

MODE

KP

KP
KP
KP
KP
KP
KP
KP

Q((

#66



5'V
245V
5J(V

45V
.Q((

#P.)



2#75

5.'2

'0&

&K52

5;5

(W0E

MODE

Return to normal display

*6

*7

MODE

MODE

MODE

Normal display method

Reverse display

Settings complete

Go to system setup mode

Go to detection setup mode

Return to original display setup mode

Do not set up sub-display

Extension display

Bar display

Excess gain display

Light intensity hold display *

1

Excess gain hold display *

1

L-on / D-on display

Disable the saturation of the
Preset function

Enable the saturation of the
Preset function *

2

MODE

MODE

5V)
5V)
5V)

4'W

5V) &K52

Q((

QP

MODE

5W$

Q((

56&'

$#4
2'4

*.&
*.&2
.FQP

MODE

MODE

24*

QP

Q((

'0&

5;5
(W0E
&K52

24*

5W$
5W$
5W$
5W$
5W$
5W$

4'W

Return to normal display

MODE

MODE

Disable APC

Enable APC

Settings complete

Go to detection setup mode

Go to original display setup mode

Return to system setup mode

Normal operation

Twice number of
interference-prevention units as

56&

(response time 2 times slower)

Do not use eco feature

Enable eco feature

Reduce power consumption
(response time 4 times slower)

Disable common key operations

Enable common key operations

MODE

MODE

MODE

MODE

MODE

MODE

MODE

5V)
5V)
5V)

#2%

5V) 5;5

Q((

QP

KPV(

56&

&Q$.

'EQ

Q((

QP

(W..

.KP-

Q((

QP

'0&

(W0E
&KU2

5;5

#2%

Standard current value display

Maximum current value display
(4 times hysteresis)

)#KP

5VF

(W..

)CKP

'EQ
'EQ

KPV(

.KP-

Return to normal display

*1

Light intensity detection mode

Limit setting output mode

Auto reset

User reset

Warning output mode

Timer OFF

Off-delay timer *

1

On-delay timer *

1

One-shot timer *

1

Settings complete

MODE

MODE

MODE

6Q((

Q((&
Q0&
5JQ6

EJ







5VF
EJ

.K/V

T5V

75'4

EJ

#.TV

#WVQ

'0&

T5V

MODE

Return to normal display

MODE

6

Specifications

*1 Use a cable length of 30m or less for M8 connector and e-CON connector types.
*2 In creases 100 mW (4.0 mA) for High Speed mode
*3 One or two more units connected: -10 to +55qC; 3 to 10 more units connected: -10 to +50qC; 11 to 16 more units connected: -10 to +45qC. When using 2-outputs, one unit is counted as two units.

All temperature regulations are for when the unit is mounted on a DIN rail and installed on metal sheeting.

Warranties and Disclaimers

KEYENCE, at its sole option, will refund, repair or replace at no charge any defective Products
within 1 year from the date of shipment. Unless stated otherwise herein, the Products should
not be used internally in humans, for human transportation, as safety devices or fail-safe sys­tems. EXCEPT FOR THE FOREGOING, ALL EXPRESS, IMPLIED AND STATUTORY WAR­RANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE AND NONINFRINGEMENT OF PROPRIETARY RIGHTS, ARE
EXPRESSLY DISCLAIMED. KEYENCE SHALL NOT BE LIABLE FOR ANY DIRECT, INDI­RECT, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES, EVEN IF DAMAGES
RESULT FROM THE USE OF THE PRODUCTS IN ACCORDANCE WITH ANY SUGGES­TIONS OR INFORMATION PROVIDED BY KEYENCE. In some jurisdictions, some of the fore­going warranty disclaimers or damage limitations may not apply.

Ty pe

Standard 1 output

Monitor

output

High functionality 2 output

Cable/M8 connector

Cable

M8 connector

*1

e-CON connector

*1

Cable Cable

M8 connector

*1

Main unit/sub unit

Main unit

Sub unit

(with output

cable)

Main unit

Sub unit

(with output

cable)

Main unit

Sub unit

(with output

cable)

Main unit Main unit

Sub unit

(with output

cable)

Main unit

Sub unit

(with output

cable)

Model NPN FS-N11N FS-N12N FS-N11CN FS-N12CN FS-N11EN FS-N12EN FS-N11MN FS-N13N FS-N14N - -

PNP FS-N11P FS-N12P FS-N11CP FS-N12CP - - - FS-N13P FS-N14P FS-N13CP FS-N14CP

Control output 1 output 1 output 1 output 1 output 1 output 1 output 1 output 2 output 2 output 2 output 2 output

Monitor output (1-5 V) - - - - - - 1 output - - - -

External input - - 1 input 1 input 1 input 1 input - 1 input 1 input - -

Response time

50 Ǵs (HIGH SPEED)/250 Ǵs (FINE)/500 Ǵs (TURBO)/1 ms (SUPER)/4 ms (ULTRA)/16 ms (MEGA)

Control
output

NPN output NPN open collector 30 V; 1 output max: 100 mA or less; 2 output total:

100 mA or less (used stand-alone)/20 mA or less (multiple connections); residual voltage 1 V or less

PNP output PNP open collector 30 V; 1 output max: 100 mA or less; 2 output total:

100 mA or less (used stand-alone)/20 mA or less (multiple connections); residual voltage 1 V or less

Monitor output

1 to 5 V voltage output; load resistance 10 k: or more; repeat precision r 0.5% of F.S.; responsiveness 1 ms (FS-N11MN only)

External input input time 2 ms (ON)/20 ms (OFF) or more

Multiple connections to sub
units

Up to 16 units can be connected total, but two-output type is treated as two units

Number of interference
prevention units

0 for HSP; 4 for FINE; 8 for TURBO/SUPER/ULTRA/MEGA (When set to double, the number of interference-prevention units will be doubled.)

Rating Power volt age

12 - 24 V DC r 10% ripple (P-P) 10% or less

NPN

Normal:900 mW or less (36 mA max. at 24 V, 48 mA max. at 12 V)

*2

Eco on mode:800 mW or less (32 mA max. at 24 V, 39 mA max. at 12 V)

*2

Eco Full mode:470 mW or less (19 mA max. at 24 V, 23 mA max. at 12 V)

PNP

Normal : 950 mW or less (39 mA max. at 24 V, 52 mA max. at 12 V)

*2

Eco on mode : 850 mW or less (35 mA max. at 24 V, 44 mA max. at 12 V)

*2

Eco Full mode : 520 mW or less (21 mA max. at 24 V, 26 mA max. at 12 V)

-

Normal : 1050 mW or less( 42 mA max. at 24 V,

56 mA max. at 12 V)

*2

Eco on mode : 950 mW or less(38 mA max. at 24 V,

47 mA max. at 12 V)

*2

Eco Full mode : 600 mW or less(24 mA max. at 24 V,

29 mA max. at 12 V)

Environme
ntal
resistance

Operating
ambient
luminance

Incandescent lamp: 20,000 lx or less; Sunlight: 30,000 lx or less

Operating
ambient
temperature

-10 to +55 qC (no freezing)

*3

Operating
ambient
humidity

35 to 85% RH (no condensation)

Vibration
resistance

10 to 55 Hz Compound amplitude 1.5 mm, 2 hours for each of X,Y,Z axis

Shock
resistance

500 m/s

2

3 times for each of X,Y,Z axis

Case material Both main unit and housing material: Polycarbonate

Weight Approx 75g Approx 45g Approx 22g Approx 22g Approx 22g Approx 22g Approx 75g Approx 80g Approx 70g Approx 22g Approx 22g

Specifications are subject to change without notice.

KEYENCE CORPORATION

1-3-14, Higashi-Nakajima, Higashi-Yodogawa-ku,
Osaka, 533-8555, Japan
PHONE: [phone]

A6WW1-MAN-0059

Copyright (c) 2009 KEYENCE CORPORATION. All rights reserved.

00603E 0079-1 96M00603 Printed in Japan

CANADA

Phone: [phone]

CHINA

Phone: [phone]

CZECH REPUBLIC

Phone: [phone]

GERMANY

Phone: [phone]

FRANCE

Phone: [phone]

AUSTRIA

Phone: [phone]

HONG KONG

Phone: [phone]

BELGIUM

Phone: [phone]

ITALY

Phone: [phone]

JAPAN

Phone: [phone]

KOREA

Phone: [phone]

MEXICO

Phone: [phone]

MALAYSIA

Phone: [phone]

NETHERLANDS

Phone: [phone]

HUNGARY

Phone: [phone]

POLAND

Phone: +4

8 71 36861 60

SINGAPORE

Phone:

[phone]

SLOVAKIA

Phone: [phone]

SWITZERLAND

Phone: [phone]

THAILAND

Phone: [phone]

TAIWAN

Phone: [phone]

UK & IRELAND

Phone: [phone]

USA

Phone: [phone]

www.keyence.com