Keyence FS-N10 Series Instruction Manual

1

Digital Fiber Sensor

FS-N10 Series

Instruction Manual

Read this manual before using the product in order to achieve maximum performance.
Keep this manual in a safe place after reading it so that it can be used at any time.

Hints on Correct Use

• Do not wire the amplifier line along with p ower lines or high-tension lines, as the sensor m ay

malfunction or be damaged due to no ise.

• When using a commercially available switching regulator, ground the frame ground terminal

and ground terminal.

• Do not use the FS Series outdoors, or in a place where extraneous light can enter the light-

receiving element directly.

• Due to individual dispersio n characteristics and the dif ference in fiber unit models, the maxi-

mum sensing distance or displayed value may not be the same on all units.

• If the sensor is used for a long time with the APC function enabled and the LED is imposed

with a heavy load, the current consumption of the sen sor for light emission will become con­stant and 'END APC' will be displayed. The sensor can still be used in this case. However,
replace the sensor if even small changes in received light intensity should be detected for
precise detection.

Precautions on Regulations and Standards



UL Certificate

This product is an UL/C-UL Listed pr oduct.

• UL File No. E301717

• Category NRKH,NRKH7

• Enclosure Type 1 (Based on UL50)

Be sure to consider the following specifications when using this product as an UL/C-UL Listed Product.

•

Use the power supply with Class 2 output defined in NFPA70 (NEC: National Electrical Code).

•

Power supply/ Control input/ Control output shall be connected to a single Class 2 source only.

•

Use with the over current protection device which is rated 30V or more and not more than 1A.

Included accessories

• Instruction Manual 1pc.

FS-N10 Series Quick Start



Quick Start

*1 This is a channel switch on 2-output types. This is not equipped with the 0-line type.
*2 Press and hold the [MODE] button to make advanced setting changes.

Names of Each Part of the Main Unit and Expansion Unit

*1 Setting to "M" locks the power mode to MEGA mode. The switch is a channe l switch for the

two output type. This is not equipped with the 0-line type.

*2 On the FS-N1C, this is an M8 connector rather than a cable. On the FS-N1EN, this is

an e-CON connector.

Mounting Unit



Mounting on a DIN Rail

1 Align the claw at the bottom of the main body with

the DIN rail, as shown in figure1.
While pushing the main body in the direction of
the arrow 1, push down in the direction of arrow 2.

2 To dismount the sensor, raise the main body in

the direction of the arrow 3 while pushing the
main body in the direction of arrow 1.



Installation on a Wall (Main Unit Only)

1 Attach the unit to the optional mounting bracket (OP-

73880), and secure with two M3 screws as shown in
figure2.

Connecting Fiber Unit

1 Open the dust cover in the direction shown by

arrow 1.

2 Move the fiber lock lever in the direction shown

by arrow 2.

3 Insert a fiber unit into the amplifier as indicated

by arrow 3 (approximately 14 mm).

4 Move the fiber lock lever in the direction shown

by arrow 4 to secure the fiber.

Failure to follow these instructions may lead to death or seri­ous injury.

Failure to follow these instructions may lead to injury.

Failure to follow these instructions may lead to product dam­age (product malfunction, etc.)

Provides additional information on pr oper operation.

This provides useful tips for the feature being descr ibed.

See "FS-N10 Series User's Manual" for details on the features of the FS-N10 Series and
detailed instructions for configuration.

• This product is just intended to detect the object(s). Do not

use this product for the purpose to protect a human body or
a part of human body.

• This product is not intended for use as explosion-proof

product. Do not use this product in a hazardous location
and/or potentially explosive atmosphere.

• This product uses DC power. Do not apply AC power. The

product may explode or burn if an AC voltage is applied.

Danger

Warning

Caution

Note

Tip

Warning

Fine sensitivity adjustment

Mode/Output *2

Press the [MODE] button once, then

to select L-on or D-onuse

Preset function

Configure easily
with a single press
when receiving light

DownUp

Power select switch *

1

Standard ⇔MEGA (fixed)

Setting value

Light intensity

Sensitivity setting

Press once each for workpiece/no workpiece

Sub screen
(Displayed in green)

Main screen
(Displayed in red)

Dust cover

Fiber lock lever

Manual button

( )

MODE button (MODE)

Power select switch*

1

Cable*

2

Expansion
protective cover

Expansion connector

Preset button (PRESET)

SET button (SET)

Operation status indicators

Digital display

PST indicator

DTM indicator

3

2

figure1

1

OP-73880

figure2

Fiber insertion sign

1

3

2

4

96M11513

2

.

Connecting Multiple Amplifiers

Up to 16 expansion units can be connected to one main un it. However, two output types will be
treated as two main units.

1 Remove the protection covers from the main unit

and expansion unit(s).

2 Install the amplifiers on the DIN rail one at a time.

3 Slide the main unit and expansion unit(s) together.

Engage the two claws of the expansion unit with
the recesses on the main unit side until you hear/
feel a click.

4 Attach the end units (opt ion: OP-26751) to the DIN

rail in the same way as step (2).

5 Secure the amplifiers between the end units.

Tighten the screws at the top (two screws x two
units) with a Phillips screwdriver to fix the end
units.

Calibration Method



Detecting Even Small Differences

z

Two-point Calibration

Two-point calibration is the basic method of calibration.
Press the [SET] button onc e without the workpiece, and then press it once agai n with the
workpiece.

1 Press the [SET] button with no workpiece.

[SET] will be displayed on the sub-menu (green display).

2 Press the [SET] button with workpiece.

The values will be set and the submenu (green display) will flash. The values will be set to
the mid-point between the light intensity when there is no workpiece, and the light intensity
when there is a workpiece.

If "----" flashes for two seconds on the main screen, the light intensity is too small between
conditions when the workpiece is absent and when it is present. These values will be set,
but there is the possibility that det ection may become unstable.

Other Calibration Methods



Increased Resistance to Dust and Dirt

z

Maximum Sensitivity Calibration

In the state shown below, press and hold the [SET] button for three seconds or more. Stop
pushing when "5'6" flashes.
The sensitivity is set slightly higher than the received light intensity.



Calibrate with a Moving Workpiece

z

Fully Automatic Calibration

Press and hold the [SET] button with no workpiece in place. While “5'6” is flashing, pass a
workpiece through. (Continue pressing the [SET] button while the workpiece passes through.)



Position Workpiece

z

Positioning Calibration

Press the [SET] button with no workpiece.
Place the workpiece in the location you wish to position it. Press and hold the [SET] button
for at least 3 seconds. Release the button when "5'6" flashes.

Simple, User Friendly Functions



Setting the Current Value to 100.0

With the FS-N10 Series, you can set the current value to 100.0 using simple operations.
Standardizing the current value makes it possible for the sensor amplifiers t o instantly differ­entiate reductions in light intensity and is useful in predicting the need for maintenance.

• If a thin fiber unit is used, an adapter provided with the thin fiber unit will be
required.
Unless the correct adapter is connected, the thin fiber unit will be loose and
not detect targets correctly (the adapter is supplied with the fiber unit).

• To connect the coaxial reflective type fiber unit to the amplifier, connect the

single-core fiber to the transmitter side, and connect the multiple-core fiber
to the receiver side.

Mount on DIN rail and install on metal surface when connecting to
multiple amplifiers or mounting main units together.

• When connecting with units other than N-bus (a general term for the KEY­ENCE wire-saving connection system) compatible sensor amplifiers,
including the FS-N10 Series, and the network unit NU Series, consult your
nearest KEYENCE dealer.

• Turn the power off before connecting multiple expansion units.

• D o not touch the expansion connector with your bare hands.

Note

φ1.3

φ1.0

Adapter A

(OP-26500)

Adapter B

(OP-26501)

Cable outer dia Adapter Appearance

Receiver

Transmitter

Single-core fiber

Multi-core fiber

Warning

Note

OP-26751 (a set of two)

Workpiece

Workpiece

• The various Preset functions listed below cannot be used when the Zero­Shift function is enabled. Disable the Zero-Shift function before executing
the following functions.

• The Preset functions are not suited for transparent workpieces and other
cases of detection with low light intensity differences.

You can disable various Preset functions by pressing and holding the [PRESET]
button.

Workpiece

Thrubeam model

: with

workpiece

: without

workpiece

Reflective model

Press and hold for 3 seconds or more

Press and hold for 3 seconds or more

Workpiece

Common to

Thrubeam

and

Models

Reflective

While pressing the [SET] button

pass through a workpiece

Settings complete

Press and hold until
"

UGV

" flashes

Common to

Thrubeam

and

Models

Reflective

Workpiece

Press [SET] button once with
no workpiece

Press and hold [SET] button with

workpiece

Settings complete

Press and hold until
"

UGV

" flashes

Note

Tip

3

z

Preset Function

This function adjusts the current value to "".
With light received, press the [PRESET] button. The current value is set to "".

Pressing the [PRESET] button changes the setting and current value as shown below.

• Presetting with preset disabled:

The setting is changed to "". The setting can be changed via the normal calibration
method.

• Presetting with preset enabled:

Only the current value is changed to "", and the setting is not changed.

.

z

Work-Preset Function

This function adjusts the current value to "".
After executing the Preset function in a condition in which you would like "" to be dis­played, executing this function in a condition in which you would like "" to be displayed, will
adjust any two points to "" and "".

Pressing the [PRESET] button and the button at the same time will set the current
value at that time to "". Values that have been set to "" with the Preset function cannot
be changed.

z

Maximum Sensitivity Preset Function

This function sets conditions that will serve as reference, to "" and adjusts conditions with
slightly high light intensity as "". This is useful when you would like to perform detection
using the background as a reference with reflect ive models.
In the following conditions, press and hold the [PRESET] button for 3 seconds or more then
release your finger when "#WVQ" is flashed.

• The maximum value for the light intensity while the [PRESET] button is being pressed is

set to ", and light-intensity that is slightly higher than the maximum value at that time
will be adjusted to "".

• The setting value is ""

• The green [PST] indicator will light up.

z

Full Auto Preset Function

This function automatically differentiates between two conditions (presence/absence of
workpiece) and adjusts the current values to "" and "". This is effective for cases when
the workpiece is moving at high-speed.
Press and hold the [PRESET] button with no workpiece in place. While "#WVQ" is flashing,
pass a workpiece through. (Continu e pressing the [PRESET] button while the work piece
passes through.)

• Near-maximum values while the [PRESET] button is being pr essed and held are

adjusted to "" and near-minimum values are adjusted to "" .

• The setting value is changed to ""

• The green [PST] indicator will light up.



Set Current Value to "0"

z

The Zero Shift Function

This function is primarily used with reflective models.
Press the [PRESET] button and button at the same time.

• The current value is set to "".

• Green "PST" light s up

z

Disable the Zero Shift Function

Press and hold the [PRESET] button to disable the zero shift function.



Adjusting the current intensity value when it is too large
(when saturated).

z

Use the Saturation Recovery Function

Press the [SET] button while pressing the [MODE] button.

After adjusting the light transmission level and light intensity sensitivity, the current values
will be adjusted to within the ranges listed in the table that follows.

*HIGH SPEED

z

Disable Saturation Recovery

When the saturation recovery function is enabled, press th e [SET] button while pressing the
[MODE] button to cancel it.

Handy Uses for the Preset Function

This function is most useful when performing simple detection using a thru­beam model fiber unit (e.g. completely blocked detectio n, such as when all
light axes of the fiber unit are interrupted by opaque workpieces).

The Work-Preset function can be used while the Preset function is in use
(when Preset is enabled).

When using this function with reflective models, "" will be displayed when
there is a workpiece, and "" will be displayed when there is no workpiece,
making it easy to know when t he workpiece is present or absent. Additionally,
even when with a reflective model, the background h as higher light intensity
than the workpiece, if you set a condition with low light intensity to "" using
the Preset function and then using the Work-Preset function, register a condi­tion with high light intensity as "", the background will display as "" and when
the workpiece is present, it will be displayed as "".

Cannot be executed when the Preset function is already being used (when
the [PST] indicator is flashing). Press and hold the [PRESET] button to dis­able the Preset function be fore executing this function.

Green "PST" lights up

Press [PRESET] button once

with no

workpiece

Setting is "



"

Current value is "



"

Tip

Important

Green "PST"
lights up

Current value is ""

100.0

[

PRESET] +

3.0

.0

Workpiece

Tip

Workpiece

Thrubeam model : with workpiece

: without workpiece

Press and hold for 3 seconds or more

Press and hold for 3 seconds or more

Reflective model

Note

Cannot be executed when the Preset function is already being used (when
the [PST] indicator is flashing). Press and hold the [PRESET] button to dis­able the Preset function before executing this function.

The zero shift and preset function cannot be used together. To use the
preset function, you must first disable the zero shift function.

Handy Uses for the Zero Shift Function

This function is primarily used to set the current value to "0" on a reflective
model fiber unit.

When a reflective model is first installed, the light intensity is sometimes not
set to "0".
If this happens, using the zero shift function to set the value to "0" when there is
no workpiece allows for easier understanding of the difference in light intensity.

Power mode Light intensity setting range

HSP*, FINE, TURBO 2047 ± 350

SUPER 4095 ± 500

ULTRA, MEGA 5000 ± 600

Handy Uses for the Saturation Recovery Function

This function is useful when the intensity value is saturated after installation.
This function corrects the saturatio n via a simple operation, by automatically
calibrating the light transmission level and light intensity gain.

・

Workpiece

Press and hold until
"#WVQ" flashes

While pressing the [PRESET] button
pass through a workpiece

Settings complete

Common to Thrubeam and Reflective Models

Note

Note

Tip

Press the [SET] button while
pressing the [MODE] button.

Tip

4

Output Switch

Either light-ON (L-on) mode or dar k-ON (D-on) mode can be selected.

1 While the current value is displayed, press the [MODE] button once.

2 Use to switch the output (.QP/&QP), then press the [MODE] button again.

The output change completes, and the display returns to the current value.

Connecting to External Devices



Cable Types



M8/e-CON Connector Types



M8 connector Cable (Sold Separately)

For FS-N11CN/N11CP/N12CN/N12CP/N13CP/N14CP

Error Displays and Corrective Actions

Consult your nearest KEYENCE office regarding error displays other than the ones listed above.

Initializing the Settings



Initialization Method

1 Press and hold the [SET] and [PRESET] buttons simultaneously for three seconds.

2 Use the to select "456", then press the [MODE] button.
3 Use the to select "K0K6", then press the [MODE] button.

After initialization is complete, the display returns to the current value.

z

Initial Settings

Using a Fiber Cutter and Cautions for Use



Using a Fiber Cutter

1 Insert the fiber into the cutter hole.
2 Bring down the blade in a single,

swift motion to cut the fiber.



Cautions for Using a Fiber Cutter

• The fiber cutter comes with the fiber unit.

• When cutting a fiber unit to be attached to the FS-N10 Series, be sure to use a gray fiber cut-

ter (OP-87098)

• Stopping the blade midway could cause a bad cut plane, reducing the detection range.

• Do not use the same hole twice.

Function Configuration



Basic Setting

*1 You can press the button to set between the range of 2 to 2.

FS-N11N/N12N/N13N/N14N FS-N11P/N12P/N13P/N14P

*1 FS- N11N/N13N only
*2 FS- N13N/N14N only

*1 FS-N11P/N13P only
*2 FS-N13P/N14P only

FS-N11MN

FS-N11CN/N12CN/N11EN/N12EN FS-N11CP/N12CP/N13CP/N14CP

*1 FS- N11CN/N11EN only *1 FS-N11CP/N13CP only

*2 FS-N13CP/N14CP only
*3 FS-N11CP/N12CP only

Error display Cause Solution

ErC Overcurrent in the control output.

Check the load and return the current
within the rated value.

ErE Failed to write/load the internal data. Perform initialization (p.4).

End APC Large load on the light sour ce.

Replace the sensor if highly precise
detection is required.

Loc The keylock function is ON.

For disabling (setting) method, see
"FS-N10 Series User's Manual".

12 to 24 VDC

DC3.3V

Black
(Control output 1)

(Control output 2)

PLC, etc.

White

Pink

*2

*2

Brown

*1

0V

Load

Load

Blue

*1

Sensor main circuit

Overcurrent

protection circuit

(Short-circuit
current 1 mA
or less)

12 to 24 VDC

Black
(Control output 1)

(Control
output 2)

*2

PLC, etc.

White

Pink

*2

Brown

*1

0V

Load

Load

Blue

*1

Sensor main circuit

Overcurrent

protection circuit

(Short-circuit
current 2 mA
or less)

0 V

Brown

Black

Monitor output (1 to 5V)

Orange

Load

Blue

(Control output)

12 to 24 VDC

Device with input
impedance
10 kΩ or more

Protection

circuit

Sensor main circuit

Overcurrent

protection circuit







*1



*1

DC3.3V

Sensor main circuit

Overcurrent

protection circuit

12 to 24 VDC

PLC, etc.

0V

(Short-circuit
current 1 mA
or less)

PLC, etc.

0V

(Short-circuit
current 1 mA
or less)

(Control output)

Load







*3



*1



*1

Sensor main circuit

Overcurrent

protection circuit

12 to 24 VDC

PLC, etc.

0V

(Short-circuit
current 2 mA
or less)

(Control output 1)

(Control
output 2)

*2

Load

Load

123

4

M8 connector Pin layout

FS-N11CN/N12CN

e-CON connector Pin layout

FS-N11EN/N12EN

123

4

M8 connector Pin layout

OP-73864
(Cable length: 2 m)

OP-73865
(Cable length: 10 m)

1

2

3

4

Connected
pin No.

Pin - Pin and wire color table

1 Brown
2
3
4

White
Blue
Black

Wire color

Setting Initial Value

Power mode FINE

Detection mode Std (Normal)

Setting value 50

Output switch L-on

Failure to follow the cautions below could reduce the detection range.

Press and hold for 3 seconds or more

Fiber

Always insert fiber from the side with writing

Fiber cutter
(OP-87098)

2

1

MODE

Press and hold for 3 seconds or more

HIGH SPEED mode

FINE mode

TURBO mode

SUPER mode

ULTRA mode

MEGA mode

Normal sensitivity setting method

Percentage Calibration*

1

Zero-shift calibration

Settings complete

Go to detection setup mode

Go to display setup mode

Go to system setup mode

MODE

MODE

MODE

MODE

J52

(KPG
6WT$
5W24

7.64
/')#

5V)
5V)
5V)

5'6









5VF

5'V2
15'V

'0&

(W0E
&K52

5;5

5'6
5'6

Return to normal display

MODE

5



Detection Settings

*1 Press the button to set between the range of  and (ms).

*2 Press the button to set the retouch sensitivity to a range of between .'W and .'W

and set the warning output level to a range of between 12 and 2.

*3 Press the button to toggle between Q((/Q0/-''2.
*4 Can be set between the range of  and .
*5 Can be set between the range of  and .
*6 Can be used only for the types with the external input.

Note that these functions can be used via communication when connecting with the network
unit NU Series.

*7 Only monitor output types (FS-N11MN).



Display Settings

*1 Press the button to toggle between 5VF/2`2A/D`DA/2AD`/2`DA

*2 Press the button to set between the range of 2 and 2.



System Settings

*1 Main unit only.



Two Ou tpu t

*2

*1 Press the button to set between the range of  and (ms).

*2 Only 2 output types (FS-N13N/N13P/N14N/N14P/N13CP/N14CP).

Normal (light intensity)
detection mode

DATUM1 mode *

2

Timer OFF

Off-delay timer *

1

On-delay timer *

1

One-shot timer *

1

DATUM2 mode *

2

Area detection mode

Rising Edge Detection Mode

Falling Edge Detection Mode

Settings complete

Go to display setup mode

Go to system setup mode

Return to original
detection setup mode

External input off

External calibration input

Preset input

Zero shift input

Reset input

Light transmission OFF input

Pause mode transition input *

3

Sleep mode transition input

Light emission power selection *

4

Analog scaling *

5

Return to normal display

*6

*7

MODE

MODE

MODE

Normal display method

Reverse display

Settings complete

Go to system setup mode

Go to detection setup mode

Return to original display setup mode

Sub-display off

Extended display

Bar display

Excess gain display

Light intensity hold display *

1

Excess gain hold display *

1

L-on / D-on display

Disable the saturation of the
Preset function

Enable the saturation of the
Preset function *

2

Return to normal display

MODE

MODE

Disable APC

Enable APC

Settings complete

Go to detection setup mode

Go to original display setup mode

Return to system setup mode

Normal operation

Twice the number of
interference-prevention units as

56&

(response time 2 times slower)

Eco feature off

Enable eco feature

Reduce power consumption
(response time 4 times slower)

Disable common key operations

Enable common key operations

Standard current value display

Maximum current value display
(4 times hysteresis)

Return to normal display

*1

Light intensity detection mode

Limit setting output mode

Auto reset

User reset

Warning output mode

Timer OFF

Off-delay timer *

1

On-delay timer *

1

One-shot timer *

1

Settings complete

Return to normal display

MODE

Specifications

*1 Use a cable length of 30 m or less for M8 connector and e-CON connector types.
*2 Counted as 1 output when connecting with the network unit NU Series.
*3 FS-N11MN only
*4 SUPER : 1.2 ms, ULTRA : 1.8ms, MEGA : 4.2 ms
*5 Input time is 25 ms (ON)/25 ms (OFF) only when external calibration input is selected.
*6 In creases 100 mW (4.0 mA) for High Speed mode
*7 One or two more units connected: -20 to +55°C; 3 to 10 more units connected: -20 to +50°C; 11 to 16 more units connected: -20 to +45°C. When using 2-outputs, one unit is counted as two units.

All temperature regulations are for when the unit is mounted on a DIN rail and installed on metal sheeting.

Type Standard 1 output High functionality 2 output

Monitor output

0-line

Cable/M8 connector

Cable

M8 connector

*1

e-CON connector

*1

Cable

M8 connector

*1

Cable -

Main unit/expansion unit

Main unit

Expansion unit

(with output cable)

Main unit

Expansion unit

(with output cable)

Main unit

Expansion unit

(with output cable)

Main unit

Expansion unit

(with output cable)

Main unit

Expansion unit

(with output cable)

Main unit

Expansion unit

(without output cable)

Model NPN FS-N11N FS-N 12N FS-N11CN FS-N12CN FS-N11EN FS-N12EN FS-N13N FS-N14N - - FS-N11MN

FS-N10

PNP FS- N11P FS-N12P FS-N11CP FS-N1 2CP - - FS-N13P FS-N14P FS-N13CP FS-N14CP -

Control output

1 output 1 output 1 output 1 output 1 output 1 output 2 output 2 output 2 output 2 output 1 output

N/A

*2

Monitor output (1 to 5 V)----------1 output­External input - - 1 input 1 input 1 input 1 input 1 input 1 input - - - ­Light source LED Red 4-element LED (wavelength 630 nm)
Response time

50 μs (HIGH SPEED)/250 μs (FINE)/500 μs (TURBO)/1 ms (SUPER)/4 ms (ULTRA)/16 ms (MEGA)

Output toggle Light-ON/dark-ON toggle
Timer function Timer OFF, OFF delay, ON delay, One-shot
Control
output

NPN output NPN open collector 24 V; 1 output max: 100 mA or less; 2 output total:

100 mA or less (used stand-alone)/20 mA or less (multiple connections); residual voltage 1 V or less

PNP output PNP open collector 24 V; 1 output max: 100 mA or less; 2 output total:

100 mA or less (used stand-alone)/20 mA or less (multiple connections); residual voltage 1 V or less

Monitor output

*3

1 to 5 V voltage output; load resistance 10 kΩ or more; repeat precision ± 0.5% of F.S.; 1 ms response time (HIGH SPEED, FINE, TURBO)

*4

External input

input time 2 ms (ON)/20 ms (OFF) or more

*5

Expansion Units Up to 16 units can be connected (total of 17 units including the main unit). Note that the two-output type is counted as two units.
Protection circuit Protection against reverse power connection, output overcurrent, and output surge
Number of interference

prevention units

0 for HIGH SPEED; 4 for FINE; 8 for TURBO/SUPER/ULTRA/MEGA (When set to double, the number of interference-prevention units will be doubled.)

Rating

Powe r vo ltage

12 to 24 V DC ± 10% ripple (P-P) 10% or less

NPN

Normal:900 mW or less (36 mA max. at 24 V, 48 mA max. at 12 V)

*6

Eco on mode:800 mW or less (32 mA max. at 24 V, 39 mA max. at 12 V)

*6

Eco Full mode:470 mW or less (19 mA max. at 24 V, 23 mA max. at 12 V)

PNP

Normal : 950 mW or less (39 mA max. at 24 V, 52 mA max. at 12 V)

*6

Eco on mode : 850 mW or less (35 mA max. at 24 V, 44 mA max. at 12 V)

*6

Eco Full mode : 520 mW or less (21 mA max. at 24 V, 26 mA max. at 12 V)

Normal : 1050 mW or less (42 mA max. at 24 V,

56 mA max. at 12 V)

*6

Eco on mode : 950 mW or less (38 mA max. at 24 V,

47 mA max. at 12 V)

*6

Eco Full mode : 600 mW or less (24 mA max. at 24 V,

29 mA max. at 12 V)

-

Environme
ntal
resistance

Operating ambient
luminance

Incandescent lamp: 20,000 lx or less; Sunlight: 30,000 lx or less

Operating ambient
temperature

-20 to +55 °C (no freezing)

*7

Operating ambient
humidity

35 to 85% RH (no condensation)

Vibration
resistance

10 to 55 Hz Compound amplitude 1.5 mm, 2 hours for each of X,Y,Z axis

Shock resistance

500 m/s2 3 times for each of X,Y,Z axis
Case material Both main unit and expansion unit housing material: Polycarbonate
Case dimensions H30.3mm x W9.8mm x L71.8mm
Weight Approx 75g Approx 45g Approx 22g Approx 22g Approx 22g Approx 22g Approx 80g Approx 70g Approx 22g Approx 22g Approx 75g Approx 20g

IIIInnnn

str

stru

stru

stru

ument

menta

menta

menta

ation for Science

tion for Science a

tion for Science a

tion for Science aannnndddd I I IInnnndddduuuussss

try

try

try

try

ISI sa-nv Rue du Doyenné 3 - 1180 Brussels Tel [phone] Fax [phone] web : http:// www.isi-be.com

mail : [e-mail]